Search Documents

By H. E. Wyslouzil

The highly competitive nature of the international iron ore market has forced producers to improve the quality of their pellets. The demand for low acid pellets suitable for direct reduction has resulted in an increase in the number of plants utilizing reverse froth flotation for silica reduction. Column flotation is being favoured for this service due to the low capital and operating cost of the equipment, as well as improved metallurgical performance when compared to conventional flotation cells. This paper describes the benefits of column flotation and discusses some important aspects of circuit design.

Jan 1, 1993

By D. Scott Scovira, Karl Dufresne

Blasting in geothermally high temperature ground and/or extremely reactive ground is an increasing common challenge for surface and underground mines. Many current PETN based non-electric and electronic detonators have manufacturer published in-hole temperature limits ranging from 55°C to 65°C (131°F to 150°F). When confronting blasthole temperatures above the manufacturer published limits, operations may request site-specific guidance and qualification for use. The advised safe loading window for in-hole PETN based detonators is often too short to be practicable for production blasting. To overcome limitations of PETN based initiation systems, surface mines with high temperature ground and/or reactive ground are known to load blastholes with a qualified high temperature bulk emulsion that are top primed with a cartridge of temperature qualified detonator sensitive emulsion plus an RDX detonating cord downline. As there is no in-hole delay detonator in this system, blasthole timing is accomplished with surface delays. Although this system is safe, top priming and surface delaying does influence floor quality and top size fragmentation, and safe loading windows times reduce blast block size and increase blasting frequency. A mining company with a site characterized by geothermally high temperature ground plus highly reactive ground employed a blasting system like the one described above. The site desires to improve blasting performance by moving to an in-hole delay initiation system that can withstand the site ground conditions. At the request of the mining house, DynaEnergetics developed an electronic initiation system for application in geothermally high temperature ground and/or extremely reactive ground conditions. The DynaEnergetics IGNEO high temperature electronic initiation system is rated for in-hole use in ground up to 150°C (302°F) for 48 hours. The detonator consists of a high strength detonator with an HMX base charge and thermally resistant downline. To make up a primer, the detonator is inserted into a booster charge assembly that is fitted with a small HMX shape charge. This high energy primer is designed to be compatible and reliable for firing bulk emulsions, including those with high percentages of urea inhibition to combat reactive ground. Up to 1000 detonators may be programmed in 1 ms increments up to 1500 ms. The system is controlled by a digital firing panel that can be used with either a wired or wireless trigger. The system enables high temperature and/or reactive ground sites to utilize in-hole delay initiation and realize the associated performance benefits.

Feb 1, 2024

By A. Fleming

The exploration process, like any other commercial activity, can only succeed if the objective of the exercise is clearly defined and persistently pursued. Successful exploration requires properties, funding, personnel and persistence. Many of us have years of experience in conducting exploration in our countries of residence. Conducting exploration in a foreign country, however, requires a number of significant other criteria.

Jan 1, 1997

By S. K. Kawatra, H. J. Haselhuhn

"Fine-grained hematite ore can be concentrated by the process of selective flocculation and dispersion, which relies on proper reagent selection and control of water chemistry. While many previous studies have been performed analyzing the effects of different reagents on this process in a laboratory environment, this paper focuses on investigating the water chemistry within the process in a pilot-scale continuous deslime thickener.The pH, sodium concentration, calcium concentration and magnesium concentration were varied to determine their effects on the iron concentrate grade and recovery, and the phosphorus concentrate grade and rejection in the pilotscale selective deslime thickener. The ideal pH for the iron grade and recovery of the process using a starch selective flocculant was found to be 10.5. Phosphorus rejection, however, was increased at lower pH values. Minimization of sodium concentration was shown to improve iron grade, iron recovery and phosphorus rejection. Calcium acted as a nonselective flocculant showing higher iron recovery, lower iron grade and lower phosphorus rejection with increasing concentration. Conclusions could not be drawn from the experiments that varied magnesium concentration.The zeta potential of the solid-liquid interface of particles in each sample taken was also analyzed to show relationships between zeta potential and process performance. In all cases, a maximization of the magnitude of zeta potential correlated with increased iron grade and recovery. This supports the hypothesis that a higher level of dispersion enhances the selective flocculation and separation process.IntroductionThe United States produced 53.2 million metric tons out of the 3,000 million metric tons of concentrated iron ore produced worldwide in 2012 (Tuck, 2013). With this in mind, there has been a large increase in iron ore processing research (Bolen, 2014; Carlson and Kawatra, 2008, 2013; Halt and Kawatra, 2014; Halt et al., 2014; Haselhuhn et al., 2012a,b, 2013a,b; Liu et al., 2014; Manouchehri, 2014; Sandvik and Larsen, 2014; Semberg et al., 2014). Of the 53.2 million metric tons produced, roughly 8 million metric tons of hematite (Fe2O3) concentrate were produced using a process known as selective flocculation and dispersion (Cliffs Natural Resources, 2011). This process is the only economically viable method for concentrating low grade (< 40% Fe) fine grain (< 25µm liberation size) hematite ores. It is scarcely used due to difficulty in controlling the surface chemistry of the ore and high reagent costs (Department of Energy, 2001; Haselhuhn et al., 2013a). The process is highly dependent upon both reagent selection and precise control of the water chemistry during separation. This study shows the dependence of the process performance of a pilot-scale deslime thickener on the water chemistry in the feed slurry."

Jan 1, 2015

By E. Tarshizi

This research project demonstrates the application of a mine system simulation and animation model in enhancing the efficiency of a truck-shovel operation and reducing the haulage environmental impact in an open-cut coal mine. In any mine, a key objective is to have enough equipment for production and not have excess to where it is counterproductive. Due to the advent of responsible mining, environmental regulations, and eco-friendly practices, these factors must also be considered in the analysis. The over-trucked situation at a mine will be discussed, i.e. when the number of trucks exceeds the optimum number of trucks a mine should have for the most productive/profitable mining operation. When the system has an excess number of trucks, truck utilization is reduced which impacts mine operation, capital costs and the environment, through unnecessary truck purchase, energy use, air pollution etc. A hypothetical surface coal mine layout was used for the simulation model.

Feb 23, 2014

By James E. Lawver

Response surface methodology is a well-known and powerful technique for determining optimum conditions in flotation systems. One disadvantage is the onerous task of the numerical calculations and curve platting. This paper describes a system in which the investigator simply selects the range of several flotation variables after which the design of the experiment, data analysis, generation of response surface equations, and response surface plats are automatically carried out using a digital computer and a computer-driven curve plotter. Several typical response surfaces of important variables in phosphate flotation are presented as examples. An overview of the flow charting of the system is provided in the addendum.

Jan 1, 1978

By A. L. Hornbaker

Management of mineral resources through land-use planning procedures is not a new concept, particularly at the local level of government. Colorado may well be one of the first states, however, to vigorously attempt to evaluate on both the state-wide and regional basis, mineral resource potential and to make certain that potential for mineral resources is included as one of the primary factors considered in the local land-use decision-making process. Less than a decade ago the only consideration given to mineral resource extraction, particularly aggregate resources, was whether or not they could be produced at the particular time they were needed. This attitude has now shifted to the other extreme, not only in Colorado, but other states as well, so that other interests, especially housing projects, mountain subdivisions, recreational and wilderness areas are gaining prime consideration in land-use decisions. Ideally, in a more acceptable median position, mineral resource potential would receive definite consideration at the local level.

Jan 1, 1977

By Robert Stefanko

13.1-SUBSIDENCE AND GROUND MOVEMENT ROBERT STEFANKO 13.1.1-SUBSIDENCE AND FAILURE This treatment of subsidence and ground movement will be confined to subsidence control for limiting surface damage by assessing the significant parameters affecting ground movements during mining to optimize mining techniques. The material will be equally applicable to evaporite mining as well as coal but will not deal with block caving or similar systems where failure is deliberately induced and surface protection is not necessary or provided. When an underground opening is established, the original equilibrium is disturbed with resultant stress concentrations. While many factors are involved in opening stability, the span (W) undoubtedly is one of the most important factors in failure. Assuming it is relatively small, the overlying rock strata can bridge across the opening and little if any movement or convergence of top and bottom will occur. However, as the span increases, a point is reached where the stress in the overlying rock strata exceeds some strength value of the rock, and the top breaks. If the opening span is limited to some subcritical value (-We) and/or is at great depth (D), a pseudo-arch will form, achielring stability before rupture occurs to the surface. The boundary of this arch is thought to approximate an ellipse in form with the major axis vertical and equal to four times W, although there has been little field research to substantiate this theory. However, if the width of this opening is increased at this horizon to some critical value (W,) or the same span is created in a shallower seam, the overlying strata ill progressively rupture to the surface and the characteristic subsidence trough is formed (Fig. 13-1) The area of the surface affected is much greater than the area of the seam extracted, depending on the "angle of draw" (a), which is the angle between a vertical line from the edge of the opening and another line extended to a point at which subsidence tails out to zero. This angle has been found to be about 35° in Europe but is rather academic, being a function of instrument precision in detecting subsidence. Since the subsidence effect is so small at any point beyond n 25° angle, this latter may be considered the practical limit of subsidence. Further- more, indications are that the angle of draw varies with depth and nature of the strata.&apos; In a field study over a 1,000-ft-deep potash mine in New Mexico, the maximum angle of draw was found to be 51.5°.2 So far, only a single opening has been considered. However, the width of the excavation applies to any complex mining system of entries, rooms and longwalls as long as the seam has been fully extracted and the width represents the distance from one solid rib to another. It will be noted that the amount of vertical displacement varies from point to point on the surface (s), but the maximum subsidence for a given trough occurs at the center (S). This latter value may not he equal to the maximum possible subsidence (Sm) which occurs only if a critical or super- critical (+W,) width has been exceeded (Fig. 13-1). Substantial surface damage can result when subsidence occurs. Factors affecting the amount and type of ground movement are: thickness and properties of the seam, angle of draw, width of excavation, depth and type of overburden, inclinations of strata and surface, and the amount of support left in the gob. In Europe,

Jan 1, 1973

By George W. Bain

Deposits of metals in only slightly disturbed strata have been attributed to sedimentation processes contemporary with deposition of the strata. Recently this origin has been extended&apos; to a greater variety&apos; of deposits and local enrichment has been attributed to selective remobilization of metallic minerals in the host stratum. Effects attending metallization and deformation, and exact age&apos; of the metallization are compiled to establish the sequence of events in ore deposit histories in order to clarify importance of remobilization within a formation relative to introduction from an outside source into an fav¬orable host. The pertinence respectively of deposit; origin and geometry to the work of the mining geologist is reviewed. Dwarf faunas in the Clinton iron ore, Tully pyrite bed and Rammelsberg deposit, indicate abnormal metal ions in the sedimentary environment. Slight¬ly disturbed strata are host rocks in the Swedish Kolm, Timna, Kupferschieffer, and White Pine deposit; the latter two have ore only in conjunction with tectonic structures.

Jan 1, 1966

By Jack M. Jodrey, Neil D. O’Donnell, R. A. Metz

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1992

By Earl Cook

A high-energy economy based on fossil fuels is in fundamental conflict with an ideal of clean air, clean water, undisturbed scenery, and maintenance of fragile ecosystems. There is an inevitable trade-off between the material standard of living of a modern society and the conservation of its environment. During the past four years, some of the costs of environmental protection have been internalized in the energy-flow system of the United States. The cost of bituminous coal and fuel oil usable under new air-quality standards has doubled or more. The cost of mining coal underground has risen because of a 20-30 percent reduction in productivity resulting from new environmental health and safety legislation; the economic impact of proposed surface-mine regulation may be equally severe. The cost of producing electric power has been rising at a 12 percent annual rate because of environmental costs, and would be climbing still more steeply were it not for the continued forced subsidy of natural-gas consumers by natural-gas producers. The efficiency of the automobile, already a monument to the triumph of self- indulgence over economy, is being further decreased by addition of anti-pollution devices. Part of the recent sharp rise in agricultural costs stems from the fact that five energy units of fossil fuel go into U.S. agriculture for every energy unit of raw food that leaves the farm; further large injections of fossil-fuel energy occur in the transport, processing, and refrigeration of farm products.

Jan 1, 1974

By J. F. Mack, P. R. Michael, J. M. Shapaka, S. J. Self, M. W. Richmond

"On October 11, 2000, an estimated 306 million gallons of water and coal waste slurry drained from an impoundment in Martin County, eastern Kentucky into an adjacent underground mine. Approximately 230 million gallons of the water and slurry discharged from two underground mine portals and affected over 75 miles of streams in Kentucky and West Virginia. In response to this and several other similar events, the U.S. Office of Surface Mining Reclamation and Enforcement (OSMRE) commissioned an oversight study that evaluates how well state and federal regulatory programs established under the Surface Mining Control and Enforcement Act are ensuring that impoundment operators are minimizing the potential for impoundment-basin breakthroughs. The study focuses on slurry impoundments constructed in the hollows of Appalachia where numerous coal seams and steep topography combine to result in a large number of mined seams intersecting and underlying impounding facilities. Factors under consideration include: (1) full accounting of all mineable coal seams intersecting and underlying the impoundment; (2) identification and accurate location of underground mines close enough to the impoundment to potentially affect its stability; (3) assessment of the stability of coal barriers between the impoundment basin and adjacent mines, and stability of roof rock and pillars in mines subjacent to the structure; (4) determination of the flowability of the impounded slurry when expanding or undermining the facility are being considered; and (5) measures undertaken to reduce breakthrough potential when necessary. The oversight study began in 2012 after program-evaluation criteria were defined in an OSMRE technical position paper. The study is scheduled to be completed in 2017. BACKGROUND The Surface Mining Control and Reclamation Act (SMCRA) authorizes the disposal of coal mine waste by constructing a coarse coal mine waste embankment across a valley and pumping the fine coal mine waste (slurry) into the resulting basin (Figure 1). A concern shared by many engineers, geologists, and mine inspectors familiar with coal mine waste slurry impoundments is related to the common occurrence of underground mine workings adjacent to or beneath the impoundment: the potential for slurry “breakthroughs” into mine works and subsequent breakouts into the surface waterways (Figure 2). On October 11, 2000 a combination of coal refuse slurry and water from the Big Branch impoundment in Martin County, Kentucky broke through into an underground mine and subsequently discharged into the receiving streams. The location of the point of breakthrough, pathways of slurry/water flow within the mine workings, and two points where the liquid exited the mine are shown in Figure 3. An estimated 306 million gallons of water and coal refuse slurry drained from the impoundment into the adjacent underground mine. Approximately 230 million gallons subsequently discharged from the underground mine at two portals."

Jan 1, 2015

By Abb Raymond

Finely processed industrial minerals in "powdered" form have long been utilized by the plastics, paint, rubber, paper, ceramics, and adhesives industries as fillers, extenders, coatings and special additives. These minerals, primarily calcium carbonate, talc, kaolin, titanium dioxide, and the like, have provided economic, uniform and consistent base materials which have, in turn, been used by the referenced industries to manufacture quality products. The focus of this paper will be the development of equipment and systems at ABB Raymond for the dry processing of such non-metallic minerals in order to meet what have become increasingly stringent requirements of the producers of these minerals. Changes in these requirements seem to have been accelerating rapidly during the last ten years, and it is expected this process will continue into the 1990&apos;s.

Jan 1, 1990

By Edwin R. (Original by) Phelps

Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining; 4) Surface mining normally recovers a- much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining [ ] methods because of geologic reasons such as the nature of the roof or bottom, thickness of the seam, multiple bedding, etc.

Jan 1, 1981

By K. L. Myers, R. Espell, C. Deringer

Construction of the AA Pad reclamation was completed in the fall of 2000. Seeding of the ET cover began in the late fall of 2000 and continued through May of 2001. On Saturday afternoon, June 1, 2002, a large, very localized thunderstorm struck the reclaimed AA Pad site. Eyewitnesses present at the time described a dark storm cloud parked above the site for less than half an hour. Average rainfall intensity was measured to be 122 mm (4.8 inches) per hour and peak rainfall intensity was estimated to be 213 mm (8.4 inches) to 259 mm(10.2 inches) per hour. At the time of the storm, the construction was less than two (2) years old and the vegetation had only a single season of growth. The entire period from the end of construction until the date of the storm was a drought period with below normal precipitation. Other than a few small snowmelt events, there was no precipitation event large enough to produce any significant flow in the channel network. Therefore, the very first significant runoff event was the extreme event of June 1, 2002. The storm essentially represents a large-scale field test of the design concepts used at the AA Pad site. Shortly after the storm, data was collected and analyzed with the intent of learning as much as possible about the performance of the cover system design with the expectation that the newly acquired knowledge might be utilized in future designs to further improve the performance of similar cover systems during extreme events.

Jan 1, 2003

By J. S. Hayden

It is becoming increasingly difficult to secure local aggregate resources that meet quality standards and local restrictions without conflicts with other land uses and environmental regulations. The successful integration of natural-resource information into land-use decisions is becoming increasingly important as the needs for both land and resources become more numerous, complex and urgent. Well-reasoned decisions about land-use are crucial to the Nation if infrastructure resources are to remain economically available. Provisions for uninterrupted future supplies of aggregate should be made using proper long-range planning that incorporate a multiple land-use program. That program would include identification and protection of natural resources, strategies that will permit development of resources according to future market needs and environmental considerations, and the beneficial reclamation of mined-out areas.

Jan 1, 1997

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

By David Newman

"Horizontal stress can have a profound effect on the stability of an underground limestone mine. The presence of horizontal stress is usually determined once the mine has been developed and the orientation of headers and crosscuts are well established. Multiple attempts are typically made to control roof falls without re-orienting the mine. Once the decision has been made to change the orientation, pillar centers, mine opening widths, and the question of how to determine the correct orientation must be answered.A case history is presented to illustrate how geologic structure, ground conditions and roof falls in adjacent mines, the World Stress Map (Heidbach et al., 2016), in-mine measurement of “cutter” roof orientation, the orientation of strata offset (cats eyes) within borescope holes, and the diametral deviation method of determining horizontal strain from drill core were used to establish the most likely range of horizontal stress.The main headers were re-orientated in a direction parallel to the median of the range of horizontal stress. The crosscuts were angled 60° to the headers to avoid being perpendicular to the horizontal stress direction. Pillar centers and opening widths were increased in the favorable stress direction of the mains and decreased in the less favorable crosscut orientation. The major principal horizontal stress magnitude was estimated using the strain measurements from the diametral deviation method and elastic modulus obtained through testing.INTRODUCTIONOver the past decade, there has been a significant increase in the number of underground stone mining operations in the United States. As stripping ratios at surface quarries become uneconomical and reach the extent of the mineral boundary, coupled with the encroachment of urban development on previously rural mining operations, the remaining mine reserves are best accessed through underground development.Although the majority of underground limestone mines in the Midwest are in relatively flat lying deposits with minimal geologic structure, many Appalachian mines are in folded and faulted environments. Tectonic horizontal stresses associated with multiple orogenic episodes are locked in the formation and are released as the underground mine is developed.A common misconception is that horizontal stress impacts are more prevalent at shallow depths where the ratio of horizontal to vertical stress may be high. However, field observations and academic research indicates that horizontal stress conditions may be encountered at any depth due to the tectonic compression of the limestone formation (Esterhuizen et al., 2007; Dolinar and Esterhuizen, 2007; Iannacchione et al., 2003; Slaker, Murphy, and Miller, 2017; Kuhnhein and Ramer, 2004). This paper outlines mine design and layout guidelines for the mitigation of horizontal stress impacts on underground stone mining operations through a case history example. This approach to mine planning and the ability to anticipate horizontal stress can significantly improve future production of multiple levels (Newman and Newman, 2019). As underground stone production continues at deeper depths and in more geologically and geometrically complex mining conditions, an emphasis on ground control and the anticipation of horizontal stress can provide safer and more productive single and multiple level mining operations."

Jan 1, 2019

By S. Bahrampour

One of the basic requirements for designing an optimized rock support for an underground opening is having reasonably enough geological information. It is often financially impractical to obtain detailed geological information about the rock surrounding the excavations. The geological and geotechnical information which are obtained during the construction phase are also usually inadequate and need periodic operation stoppage. Penn State University- J.H. Fletcher & Co. joint venture is to improve the existing instrumented roofbolter so that the 3D geological and geotechnical map of the rock mass surrounding the underground working can be generated real-time as the data is being collected. This information will also be used to design appropriate support for different sections of mines. In this paper, recent results in improving the performance of the measurement while drilling system will be discussed. Moreover, updates related to borehole probing methods for estimating the properties of the rock masses will be presented.

Feb 23, 2014

By Wen Tao Liu, Tong Tian, Fu Sheng Niu, Xiu Man Liang

The level of automation employed in flotation production is relatively low. In an actual concentrator, operators use their judgment to adjust the production state based on the visual characteristics of the flotation froth surface. There are shortcomings, such as strong subjectivity and lagging process operation, that easily cause the waste of manpower and material resources. Machine vision technology is introduced to replace human visualization, achieving a quantitative description of the visual characteristics of the froth surface. The state variable parameters are provided for the identification of the flotation conditions.