Search Documents

By C. W. Davis

During the second year of its existence the Ore-Testing Section has actively prosecuted work in the standardization of testing methods, in conducting routine tests and analyses for other Government agencies, and in the determination of recommended processes for the treatment of representative ores from mining districts. Close cooperation has been maintained between the members and units of this Section and those of other Sections. J. A. Woolf and J, B. Clemmer have continued to act in an advisory capacity and. R. E. Head has contributed valuable assistance in the microscopic examination of ores and metallurgical products that did not respond readily to standard treatment methods.

Jan 1, 1938

By Walter R. Storms

This paper, which describes the mining methods of the Potash Co. of America in Eddy County, N. Mex., is one of a series being prepared by the Mining Branch, of the Bureau of Mines on mining practices and methods in various mining districts of the United States. 4, T. The mine and plant of Potash Co. of America are situated in sec. 20 S., R.. 30, E.,. N. M. P. M., about 22 miles by paved road northeast of Carlsbad (fig. 1). A spur line of the Atchison, Topeka & Santa Fe Railroad also connects the mine with Carlsbad.

Apr 1, 1948

By C. E. Jordan

The fundamental properties of dielectric separation were studied to provide insight into the design and operating characteristics of a dielectric separator. Force equations on mineral particles were derived and evaluated experimentally. Responses to variations in the electrical voltage and frequency, feed rate, particle size, dielectric fluid, and dielectric constant were tested theoretically and experimentally, using a 5-cm-diam dielectric separator. High-dielectric mineral recovery was proportional to the calculated effective dielectric force volume (EDFV) that surrounded each drum-electrode wire. Electrode spacing was the most sensitive design parameter; spacing of less than 0.4 cm was required for a good separation. Dielectric separation was effective for separating minerals with dielectric constants that differed by approximately 2 or more.

Jan 1, 1985

By Ruth F. Brinkley

This report is the 16th of a series of reports originally issued annually and more recently biennially to acquaint the reader with the work of the Explosives and Physical Sciences Division, Region VIII.3/ In the majority of instances the results of the investigations are made available to the public through Government publications and journal articles. In certain instances (specifically as regards security-classified research, investigations of a confidential nature, and short-range programs of very limited scope) results are reported only to those immediately concerned.

Jan 1, 1957

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1984 was $409.8 million, and established a new record high for value of nonfuel minerals in the State, at 13.4:% over the previous high of 1983. Output of nearly all nonfuel minerals increased; phosphate rock was one of the exceptions, with no recorded output in 1984. Cement, crushed stone, lime, sand and gravel, and clays were the major commodities produced in Alabama. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in fire clay and kaolin; fourth in bentonite, ferroalloys, and dimension marble; fifth in masonry cement, lime, and recovered sulfur; and sixth in portland cement. Alabama ranked 22d in the Nation in value of nonfuel minerals produced.

Jan 1, 1986

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

Reduce haulage truck accidents resulting from blind spots, with a special emphasis on reducing accidents during backing operations.

Jan 1, 1997

By John R. Bradley

The available supply of fuel and power is a subject of importance at all times and particularly at this time. The following brief survey of fuel and power in the United States appraises the extent of the several primary sources of energy the approximate monthly demand, 1929-40; the chief centers of production and consumption; and shifts in the principal uses from 1929 to recent years. The period covers the boom year 1929, the years of the great depression, the more normal year 1937, the recession in 1938, the year 1939, and 1940 (which was affected by armament programs). In some instances, the data for 1939 and 1940 are preliminary. The four primary sources of fuel and power are coal, petroleum, natural gas, and water power. Wood fuel, important in some regions, and foreign trade in natural gas and hydroelectricity represent a relatively small part of the energy supply and are not considered in this study. The tonnages shown are in terms of coal, based upon the calorific or B. t. u. equivalents of the several sources of power. In practice, the usable heat or energy varies according to the type of equipment available for its use. For example, the efficiency of turbine water wheels and internal-combustion engines is much higher than that of steam plants and household-heating devices.

Jan 1, 1941

By A. B. Hooker, P. G. Guest, E. J. Gleim

"From time to time the United States Bureau of Mines has received reports of gas explosions alleged to have been caused by correctly assembled flame safety lamps. In most of the mines where the explosions occurred the lamp was in use at a working face where the velocity of the ventilating current would be relatively low. The inference has been that the lamp was correctly assembled but that the gauze became sufficiently overheated to ignite the surrounding atmosphere.As part of its routine investigation of flame safety lamps the Bureau of Mines subjects each lamp to a test in still and moving atmospheres to determine its safety. Heretofore, as long as the lam, successfully passed this and other tests no determinations as to the margin between success and failure were made; hence, in attempting to answer inquiries concerning the reported explosions it was found desirable to be able to give actual gauze temperatures as a measure of the comparative safety of lamps under various conditions. The previous laboratory tests of flame lamps in still mixtures were made in a chamber or ""gallery"" of relatively small volume where the lamps might have been subject more or less to the smothering effect of the combustion products. It was therefore decided to make a special series of tests to obtain the gauze temperatures of both bonneted and unbonneted lamps in still and low velocity mixtures, using a larger gallery to offset any smothering effect.These tests are believed to represent the first attempt at measuring gauze temperatures by means of themocouples. The results will not only be of interest but will also be helpful to many in determining the status of flame safety lamps relative to gas ignitions in mines."

Feb 1, 1929

By Steven J. Schatzel

Prior research has suggested that the source of respirable silica dust in underground coal mines is typically the immediate top or bottom lithology adjacent to the mined seam, not mineral matter bound within the mined coal bed. Geochemical analyses were applied in an effort to identify the specific source rock of respirable quartz dust in coal mines. The analyses also demonstrate the compositional changes that take place in the generation of the respirable dust fraction from parent rock material. All six mine sites were mining coal with relatively low mineral matter content, although two mines were operating in the Fire Clay coal bed which contains a persistent tonstein. Interpretations of Ca, Mg, Mn, Na, and K concentrations strongly suggest that the top strata above the mined seam is the primary source of mineral dust produced during mining. One site indicates a mixed or bottom source, possibly due to site specific conditions. Respirable dust compositional analyses suggest a direct relationship between the quantity of mineral Si and the quantity of quartz Si. A similar relationship was not found in either the top or bottom rocks adjacent to the mined seam. An apparent loss of elemental Al was noted in the respirable dust fraction when compared to potential parent rock sources. Elemental Al is present in top and bottom rock strata within illite, kaolinite, feldspar, and chlorite. A possible explanation for loss of Al in the respirable dust samples is the removal of clays and possibly chlorite minerals. It is expected that removal of this portion of the Al bearing mineral matter occurs during rock abrasion and dust transport prior to dust capture on the samplers.

Jan 1, 2009

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By Thomas M. Barczak, Joe Bower, Jinsheng Chen

Pumpable roof supports provide an alternative longwall tailgate roof support and have grown in usage during the past few years. Heintzmann Corporation has been installing pumpable roof supports at the RAG Resources Emerald Mine in western PA since 1998, where they have provided effective roof control in their longwall tailgates. Despite the success of these supports in this application, questions remain regarding critical design issues for optimizing the use of this support technology. The support loading profile is characterized by a high initial stiffness with peak loading occurring at less than one inch of convergence, followed by significant load shedding with a post failure capacity comparable to that of wood cribbing. Therefore, the key to optimizing the support utilization is to provide sufficient load density to prevent convergence from occurring beyond the peak loading capacity. This requires an understanding of how the supports interact with the ground conditions, hence measurement of the ground reaction curve. In order to obtain this information, pumpable roof supports were instrumented to measure support loading. Roof deformation and roof-to-floor convergence measurements in the vicinity of the instrumented supports were also made. The experimental parameters for the installation were the support spacing and water-to-solids ratio of the grout, which controls the grout strength and ultimately the maximum capacity of the support. The study clearly shows that at this mine a 24-inch diameter support is fully capable of providing adequate ground control under depths of cover of 750 ft as only 50 pct of the available support capacity was utilized outby the longwall face. It was also shown that the 2.00 to 1 water-solids ratio, despite providing a slightly softer support response, is sufficient for maintaining the same degree of roof control provided by the traditional 1.75 to 1 grout mix. The 10-ft spacing of the supports did not cause any ground control problems outby the face. However, inby the face the performance of the support is degraded once the peak capacity of the supports is exceeded. It appears that the large load shedding behavior, which is characteristic of this support following peak loading, allows the immediate roof to separate. When this happens, the support is unable to regain control of the roof in time to prevent failure of the immediate roof beam.

By T. M. Garland

This report presents a Bureau of Mines assessment of crude oil and associated gas production and reserves that would result from different drilling efforts in the lower or contiguous 48 States during the 1972-85 period. The drilling effort was based upon five growth rate assumptions from the 1971 level. Additions to crude oil reserves were computed for nine cases resulting from the use of three equations for findings per foot drilled and three constant revision factors. The results indicate that the United States will not become self-sufficient in crude oil production by 1985 and also illustrate the lead time required to reverse the decline in oil production. Discussion is limited to three of the nine cases to provide high, intermediate, and low results. More emphasis is on the intermediate case because it is indicative of the most probable trends. The methodology and statistical data are included in the appendices.

Jan 1, 1974

[ ]

Jan 1, 1975

By Gregory J. Chekan

The Bureau of Mines, in an effort to improve planning and development in coal mining, is investigating strata interactions associated with mining of multiple coalbeds. Two common interactions that occur between adjacent coalbeds are subsidence and pillar load transfer. The study described involves underground observations and measurements conducted at two Pennsylvania mines, each affected by one of these interactions. At the mine affected by subsidence, measurements show that undermining had little effect on upper mine pillar stability, but had a more severe effect on the development and maintenance of entries. Roof-to-floor measurements recorded over four times more convergence in entries developed over gob as compared with entries developed over support pillars in the lower mine. At the mine affected by pillar load transfer, Initial in situ measurements have shown the existence of a pressure arch in the lower workings. Prior research has shown that arch interaction between two adjacent openings can create stress concentrations in the in-nerburden. Underground measurements and results obtained from both mine sites correlate with theoretical and photoelastic multiple-seam models, and eventually these field data will serve to refine model accuracy. Further study of multiple-seam interaction mechanisms will lead to improved mine planning, increased resource conservation, and a safer working environment.

Jan 1, 1986

By Merwin H. Howes

In constructing the NORAD Combat Operations Center, controlled blasting techniques were employed to achieve smooth walls and to avoid shattering the rock beyond excavation lines. Extraordinary measures were taken to stabilize the rock to permanently preserve the openings. Rock stabilization was accomplished by means of reinforced concrete and gunite linings, rock boltings, installation of chain-link fabric, and epoxy resin and cement grouting. A particular zone of weakness at a vital location was supported by exceptionally thick reinforced concrete lining, rock bolts, and cement grout.

Jan 1, 1966

By Alex C. Smith, Michael J. Sapko

A series of explosive detonation experiments was conducted in NIOSH’s Bruceton and Lake Lynn Experimental Mines to evaluate low level (<6 psig) detonation wave propagation behavior in single and multiple entry configurations. Entry cross-sectional area varied from 5 to140 m2 and explosive weights of Pentolite ranged from 0.24 to 2.4 kg. Behavior of the detonation wave was evaluated through recording of the pressure as a function of time and distance from the explosive detonation in single and multiple entry interconnecting tunnels. Peak pressure from detonation of an explosive in an underground mine maintains magnitude for a greater distance than is the case on the surface and is shown to follow the simple scaling rela-tionship P = 702.8(W/Vt)0.514(0.65)n, where P is the peak detonation pressure in kPa, W is the weight of the explosive charge in kg, Vt is the total volume in m3, and n is the number of splits, n = 0, 1, 2, …n. The total energy, or impulse, I, generated by these detonations can be expressed as I = 1.34(W/A)0.64n, where W is the weight of the explosive charge in kg, A is the area of the main tunnel in m2, and n is the number of side en-tries, n = 0, 1, 2, …n.

By R. L. Schmidt

Research conducted over the past 20 years in France, Great Britain, and the United States on the use of the large-hole burn cut has established cer¬tain advantages for this system. Advantages include longer pull and more complete fragmentation from blast rounds. However, research is needed to establish a set of parameters for optimum performance. As part of the Bureau of Mines Advancing Mining Technology for Marginal Resources program, the Twin Cities Mining Research Center, Twin Cities, Minn., acquired a horizontal rotary drill capable of boring holes up to 24 in. in diameter. This was used for a series of underground experiments at White Pine mine, White Pine, Mich., during 1973. Exceptional results were obtained with a 12-1/4-in void hole that yielded up to 18 ft of pull in a 10- by 20-ft drift, Fragmentation was excellent, and the compactness of the muck pile facilitated loading.

Jan 1, 1975

By R. H. Storch

"A preliminary examination of the Bi-Metallic molybdenum prospect was made in October 1944, as a result of which it was recommended that a trench exploration project be undertaken on the property. This report presents the information obtained from project work done during June 1945.In its program of exploration of mineral deposits, the Bureau of Lanes has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to the national security and. economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, special acknowledgment is due S. H. Lorain, chief, Albany Division, Mining Branch, for aid in preparing the report.The property is situated in the NW1/4, sec. 26, T. 39 N., R. 29 E. about 21 miles northeast of Tonasket. Tonasket (population 643), the nearest town, is a way point on a branch line of the Great Northern Railway. The prospect is reached by a good gravel road through Havillah to Vincent's ranch, about 3 miles northeast of Havillah. From the ranch, an abandoned dirt road extends to the portal of the Moly alit, about 1 mile distant. The mine road could be kept open without difficulty if properly graded and surfaced."

Aug 1, 1946

By Fred D. Wright

This paper describes research at the Bureau of Mines experimental oil-shale mine at Rifle, Colo., to improve blasting techniques and reduce breaking costs. Many of the conclusions are applicable to any mining operation. Experiments Were conducted on many phases of blasting. The effectiveness of various grades of explosives was compared, and several different drill-hole patterns were tried in heading rounds. An experiment was conducted to determine the maximum effective burden for various diameter blast holes. High-speed motion-picture studies were made of blasts, and the time for initial movement of rock after detonation of the explosive was measured. Experiments with millisecond-delay detonators in heading rounds proved that, when used properly, these detonators result in improved fragmentation, economical use of explosive, and compact, easily loaded muck piles.

Jan 1, 1953