Search Documents

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By A. E. Lindquist

This Bureau of Mines publication identifies areas having sufficient coal reserves to support synthetic natural gas (SNG) development and summarizes those areas having the highest potential. Capital requirements, mining and coal cost factors, water availability, and coal-quality data pertinent to SNG production are presented. Evaluation of individual coal reserve blocks was based upon coal and water requirements of the Bureau of Mines Synthane coal gasification process.

Jan 1, 1977

By E. H. Skinner

An abandoned mine shaft near Omar, in Logan County, W, was permanently sealed through a cooperative agreement between the West Virginia Department of Commerce, Labor, and Environmental Resources, Division of Environmental Protection, and the US. Bureau of Mines (USBM), Abandoned Mine Lands (AML) Program. An engineered shaft seal design was developed and demonstrated that featured lightweight concrete as a key material component at a wet density of about 45 lb/ft3. A reinforced concrete cap designed for 5 psi live load was placed over the shaft seal. Applicable new concrete technologies relating to a 100-yr design life were utilized to assure future integrity of the shaft seal. Waterproofing methods were included in the shaft seal design to provide protection from ambient moisture and corrosive mine waters and to increase the long-term durability of the shaft seal. All construction methods used in the field trial are fully adaptable for the mine-reclamation contractor, The USBM research objectives were to develop a broad generic design that will be widely applicable to other adit-sealing and shaft-sealing problems throughout the mining industry.

Jan 1, 2010

By Louis C. Britcha

"The Phelps lease in Jasper County, Missouri, was first examined by the Bureau of Mines3/ in December 1943, at the request of Thomas Phelps of Joplin, the lessee. Owing to urgent war requirements for zinc and lead and evidence of favorable geological conditions and past productivity of adjoining properties, it,considered justifiable to explore for extensions of known ore deposits and possible undiscovered ones. In August 1944, funds were allotted for this work, which was started January 5, 1945, under the direction of the author.The provision of facilities and storage space on the property by the lessee during drilling operations is gratefully acknowledged.The Phelps lease is on land belonging to the Rex Mining & Smelting Co. It lies immediately southeast of the city limits of Joplin, Mo. It may be reached by going cast from Joplin on paved 20th street to half a mile beyond Range Line road. Twentieth street is the northern boundary line of the property, which consists of approximately 145 acres and includes the W 1/2, NE1/4, and all of the E ½. NW1/4 except 15 acres along the west side of that quarter section, of sec. 18, T. 27 N., R. 32 W., as shown on figure 1.The property is part of a 1,000-acre tract owned by the Rex Mining & Smelting Co., Paul D. Porter, president, Joplin, Mo. The lease was acquired by Thomas Phelps of Joplin, in 1937. At present the lease is controlled by a recently formed association known as the Eureka Products Co., Charles W. Madison, manager, Kansas City, Mo.Dependable skilled mine labor is scarce in the district at present, but there seems to be enough transient mine labor for small operations. The prevailing wages of the district run from 55 cents to 95 cents per hour for various types of mine labor.Living accommodations and markets to supply all domestic requirements are available in Joplin.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the and that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director."

Jul 1, 1946

By S. J. Hemberger, F. W. Lee, J. H. Swatz

"INTRODUCTION This investigation was undertaken in 1939 for the purpose of securing the necessary information relating to the field techniques and accuracy that would be needed for magnetically surveying State-wide areas. The Florida,peninsula was chosen for such a study for two reasons: First, because it is geologically ideal for such an investigation, since it comprises a series of unconsolidated, flat-lying Tertiary and Cretaceous sediments of low magnetic susceptibility covering a complex and much-folded crystalline basement comprised of rocks carrying strongly -paramagnetic materials; second, because information concerning the structural trends of the crystalline basement would be of great interest and Importance in the study of Appalachian orogeny and the relationship of the Florida Peninsula to both the Appalachian and Antilleantectonte systems. The results of this magnetic survey have clearly demonstrated that the magnetic anomalies reflect variations in the crystalline a basement. To the degree which the structures of the crystalline basement control the structures of the overlying sediments these results are useful for oil exploration.MAGNETIC OBSERVATIONSAll magnetic measurements were made with a vertical Aekania magnetic variometer having a temperature compensated needle. All observations were tied into two base stations located at Fort. Myers and Gaineeville, Fla. The absolute vertical magnetic intensities at these two bass stations were determined by the United States Coast and Geodetic Survey within an accuracy of + 10 gammas. The accuracy of the base station variometer used in the present survey was of the order of ± 3 gammas. The sensitivity throughout the survey of the magnetic variemoter used on the traverses approximated 30 gammas per scale division and it is estimated that the probable error between stations along a traverse would be about + 5 gammas. Measurements were started on traverse C near Fort Myers and tied into the Fort Myers base station established by the Coast and Geodetic Survey. Twelve traverses, comprising 1,500 station observations, wore occupied between the Fort Myers and Gainsville base stations. When the cumulative total of these 1,500 interim observations was tied into the Gainesville base station it was found to differ by only 30 gammas from the value obtained by the Coast and Geodetic Survey for that base. The observations were adjusted for this difference."

May 1, 1945

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1982 was $299.4 million, a decrease of $14.4 million from that of 1981; the decrease continued a downward trend that started in 1980. Output of most nonfuel minerals declined; cement, crushed stone, lime, sand and gravel, and clays were the major commodities produced in the State. Despite the decrease in mineral output, Alabama led the Nation in the production of crushed marble; was second in bauxite; third in ferroalloys and oyster shell; fourth in bentonite and dimension marble; fifth in common clay. fire clay, and kaolin; and sixth in masonry cement and lime.

Jan 1, 1984

By D. E. Redmon

The Federal Bureau of Mines has studied the locations and general features of 90 pegmatites found in north-central New Mexico. The dominant valuable product of the pegmatites is muscovite, both sheet and scrap. However, the Harding pegmatite in Taos County is mined only for beryl. Many attempts have been made to recover scrap mica on a large scale by mechanical beneficiation of pegmatite, but the operations heretofore have been short-lived. The Globe mine and the Apache mine, both near Petaca in Rio Arriba County, have been the most important sources of sheet mica in New Mexico. Recognition of the growing need for some of the minerals derived from pegmatites led the Bureau of Mines to investigate the occurrences of pegmatite.

Jan 1, 1961

By R. J. Fantel

The Bureau of Mines investigated the resources, costs, capacities, market relationships, and short- and long-run supply of phosphate rock and phosphoric acid. The 206 mines and deposits evaluated in 30 market economy countries contain an estimated 35.1 billion mt of recoverable phosphate rock (demonstrated resource level). U.S. resources are sufficient to satisfy the domestic and export markets for phosphate products well beyond the year 2000. Because of resource depletion at current producers, however, new properties (with higher cost levels) need to be developed if U.S. production levels are to be maintained. Existing worldwide capacity can satisfy expected demand through the early 1990's. Expansion at existing mines or low demand growth could mean that no new property development will be needed before the late 1990's. Worldwide, almost $8 billion could be required for development of new phosphate rock properties between now and the year 2000, given 3-pct annual growth in demand. Most properties that could develop in the 1990's would require price increases of 20 to 50 pct to break even. To earn a 15-pct rate of return on investment, prices must rise to nearly double the present level of $24 to $29 per metric ton.

Jan 1, 1988

By J. H. East

Potash is one of the essential chemicals used in fertilizing soil deficient in natural minerals . Europe uses a large tonnage of potash in the form of easily soluble salts , and this is particularly true of those countries where the natural minerals in the soil have been exhausted owing to intensive cropping of the land . The application of potash to the soil in these countries is essential if normal crops are to be obtained ; during the war , some European countries were unable to obtain sufficient potash , and productivity of the farming areas declined seriously . • The largest -known deposits of potash in the world ; with the possible. exception of Russia , occur in Germany , and the German output of processed salts constituted about 65 percent of world production prior to the war . The German potash-plant installations are large , modern , brick and steel construction and apparently built for a planned operation of many years . Two districts produced approximately 80 percent of the German potash; the Werra -Fulda district , near Vacha , had the largest production , and the Sudharz district , near Nordhausen and Sonderhausen , was second . (Fig . 1. ) Hannover and Stassfurt were two smaller producers . Potash fertilizers are rated in terms of potassium oxide (K20 ) . The usual basis for calculation of production or application of the salt is to reduce the potash content to 40 percent K₂0 .

May 1, 1947

By Stephenson. E. L.

"INTRODUCTION In the spring of 1942 a series of magnetometer surveys on deposits of black sand underlying Pleistocene raised marine terraces along the coast of southwestern Oregon was nada by the Division of Geophysical Exploration of the Federal Bureau of Mines in cooperation with the Oregon Department of Geology and Mineral Industries. A few preliminary tests had been made in the same area in May 1940 and December 1941.The sands contain fine gold and metals of the platinum group, and, beginning in 1852, extensive, but spasmodic mining and exploration have been done for these precious metals. There are many old placer, mines and prospects, although for the most part the yield of the metals has been small. The sands also contain other minerals of potential value, including ilmenite, magnetite, garnet, zircon, and particularly chromite, and the wartime demand for domestic chromite resulted in extensive testing and development of the known deposits. The purpose of the magnetometer surveys was to determine the efficacy of, magnetic methods in tracing and outlining these known deposits and in prospecting for new ones. The field work was done between March 17 and May 29, 1942, by the author assisted by W.W. Paulsen of the Oregon Department of Geology and Mineral Industries."

Jun 1, 1945

By Albert S. Konselman

This paper describes the mining methods and operating costs for 1938 at the South Burns shaft, situated in the Cripple Creek district, Colorado. The shaft is operated by Golden Conqueror Mines, Inc., through which portions of the properties of the Acacia Cold Mining Co., The Free Coinage Gold Mining Co., and The United Gold Mines Co. are worked under lease. During 1938, 30,773.61 dry tons of ore averaging $9.59 in gold per ton was mined. Of this, 10,138.439 tons averaging $10.65 per ton was produced on company account, and 20,635.171 tons averaging $9.05 per ton was produced by "split-check" lessees.

Jan 1, 1940

By E. B. Swanson

Atlantic seaboard refining and marketing companies , dependent largely upon other producing and refining areas for the crude and refined petroleum needed to meet the demand for petroleum products within the Atlantic Coast States , reported an increase in 1929 receipts of 2,542,000 barrels of crude petroleum and 13,479,000 barrels of gasoline over the quantities received during the preceding year . The relatively large expansion in gasoline receipts undoubtedly resulted from the unexpected increase in gasoline consumption which characterized the petroleum industry during 1929. Gasoline receipts from California increased 6,354,000 barrels and shipments from foreign countries were 5,381,000 barrels in excess of the 1928 figures , while receipts from Gulf Coast ports , the major source of outside supply, declined 811,000 barrels . Shipments of domestic crude oil by tanker from Gulf Coast ports during 1929 continued the average annual increase of approximately 7,000,000 barrels which has been recorded during the five years of this annual survey . These shipments have increased from 72,556,000 barrels during 1925 to 99,828,000 barrels during 1929. Shioments of Mid- Continent crude by pipe- line to Atlantic Coast refineries have , on the other hand , dropped from 11,903,000 barrels in 1925 to 1,409,000 barrels during 1929. Receipts of foreign crude oil declined 1,461,000 barrels from the preceding year . : Gasoline demand within the Atlantic Coast area reached a total of 123,345,000 barrels , an increase of 15.7 per cent over 1928. Gasoline production increased 4,157,000 barrels , while tanker receipts were nearly 11,000,000 barrels larger than in 1928. Indicated shioments from Appalachian refineries were somewhat larger than in the preceding year . Gasoline production showed an average of 33.5 per cent of the crude throughout , as compared with 31.5 per cent in 1928 and 32.7 per cent in 1927. Cracking operations accounted for 44.6 per cent of the gasoline produced , as compared with 40.6 per cent in 1928 and 35.3 per cent in 1927. Gas oil and fuel oil production averaged 52.8 per cent of the crude throughput , as compared with 55.1 per cent in 1928 and 49.5 per cent in 1927 , the decline reflecting the smaller quantities of foreign crude refined during the year .

Nov 1, 1930

By J. W. Howland

To determine their effectiveness in different climate and soil conditions, a demonstration of dozer blades specifically designed for recontouring mine spoil was conducted at an East Texas surface coal mine. The specialized equipment included a 48-foot angle blade, a modified 24-foot "U" blade, a 13-foot deep "U" blade, and a 24-foot grading bar. Both the 4b-foot and the 24-foot "U" blades were mounted in a two-tractor, single-operator configuration. To meet flotation problems common in this mining region, a 22-foot lightweight blade was developed and demonstrated for use on a 400-430 hp tractor. The demonstration involved 1,185 acres and showed a 50% reduction in reclamation costs and a 47% reduction in fuel requirements for this mine site over conventional equipment. Improved equipment, trained operators, good supervision, and improved monitoring techniques contributed to the savings. Procedures and results of the demonstration are presented and analyzed here along with guidelines for application of findings.

Jan 1, 1981

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) in the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By W. D. Dietzman

In view of the developments and recent interest in recovering heavy oil, this report was prepared to present general information on more than 2,000 heavy oil reservoirs in more than 1,500 fields in 26 states. Information given on each heavy-oil deposit includes the following items: Field and formation, location, average or range of depth, average API gravity of oil, aver- age thickness of formation, areal extent of field, total productive wells drilled in field, discovery date of field, field status in 1963, cumulative production to Jan. 1, 1964, and all known types of secondary-recovery operations initiated (active and terminated) Fn the reservoirs. The geographical location of heavy oil accumulations in the United States is shown by a map, and a brief discussion of 14 different areas is given in the text. As of Jan. 1, 1964, 75 percent of the heavy oil reservoirs in the United States had produced more than 10 billion barrels of oil and are estimated to contain over 90 billion barrels of oil in place. It is also estimated that if the deposits which have had little or no production history, such as the one in Missouri, were included, the total remaining heavy oil in place would be in excess of 150 billion barrels. To find economical ways of recovering this vast reserve of heavy oil, industry is developing technology in several types of thermal-recovery methods. Some of the general considerations and more suitable limitations in selecting a prospect to study fur thermal-recovery techniques are: Lithology, depth, viscosity of reservoir fluids, gravity of oil, reservoir thickness, oil in place, and permeability and porosity.

Jan 1, 1965

By Charles L. Kimbell

In overall aggregate, the world's mineral industry in 1987 experienced a more satisfactory year than in 1986, at least insofar as its performance could be assessed from traditional statistical indicators. Production, trade and consumption seemingly advanced in the case of the majority of commodities, and prices for a number of commodities advanced. It was by no means certain, however, whether 1987 investment in mineral industry ventures would top the levels of 1986, when, in the case of petroleum industry investment expenditures there had been a sharp decline, this in contrast to evidences of a slight upturn in steel industry investment. World crude mineral output value was estimated at more than $1,084 billion, and the value added by minerals industry processing of this material probably raised the total value of the industry's production from primary materials to more than $2,600 billion constant 1983 dollars. Less easy too assess was the value of mineral commodities moving in international trade, but with a resurgence in oil prices from the 1986 levels, an increase above the 1986 $500 billion mark seemed assured. There are no comprehensive aggregate statistics on mineral consumption comparable to those on production and trade, but quantitative growth recorded for most major commodities suggested a favorable trend, particularly when coupled with a general (though by no means universal) upturn in unit prices.

Jan 1, 1989

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By F. E. Walker

The Bureau of Mines determined total sulfur and sulfur forms for coal in 283 counties in 29 States and 2 fields of the State of Alaska. Specifically, organic, pyritic, and sulfate sulfur were measured of approximately 2,900 samples, and they include most of the coalbeds in the United States.

Jan 1, 1966

By Matthew N. Plis

This U.S. Bureau of Mines report presents the documentation for COALVAL, a coal property evaluation software package developed on Lotus 1-2-3,4 version 2.2, spreadsheets. The software is compatible with version 3.1 as well, and may provisionally be run on the earlier 2.01 version. COALVAL is a menu-driven program that produces a prefeasibility-level cost analysis of mine-planned coal resources. The package contains cost models for each of five coal mining methods commonly employed in Appalachia: auger, contour strip, mountain top removal, continuous miner, and longwall. Other models, such as a dragline cost model, will be incorporated as the Bureau's Coal Recoverability Program matures. COALVAL allows mine operators, evaluators, consultants, and Government entities to input resource data and the various production, operating, and cost variables that pertain to their property. The program can evaluate up to 25 seams, each to be mined with up to five different mining methods, within a given area. Summary spreadsheets listing the cost per clean ton to mine the resources, f.o.b. the tipple, are produced for each property, seam, and mining method/seam combination.

Jan 1, 1993

By Alla D. Mah

Titanium forms several compounds with oxygen and also is able to dissolve interstitially about 33 atomic percent of oxygen. Starting with titanium dioxide, reduction becomes increasingly difficult as oxygen is removed; and the final step, be reduction of the titanium-oxygen interstitial solutions, is by far the most difficult. The possibility of reducing titanium oxide, or of purifying titanium containing oxygen, by treatment with certain more volatile metals has been a subject of considerable interest. Theoretical appraisal of the limitations of this possibility, however, has been hampered by lack of adequate information on the thermodynamic properties of the titanium-oxygen solutions. The purpose of the present work was to remedy this difficulty by expanding the thermodynamic knowledge regarding these solutions. The experimental work involved three types of calorimetry and furnished the following information: (1) Heats of formation of 11 titanium-oxygen solutions, in the range of 0 to 10 wt.-percent oxygen, were determined at 298.15° K. As a byproduct, an improved value of the heat of formation of rutile was obtained, which, in turn, led to improved values of the heats of formation of the lower titanium-oxygen compounds. (2) Low-temperature heat-capacity data and entropies at 298.15°K in were determined for 2 representative titanium-oxygen interstitial solutions. (3) High-temperature heat-content data were obtained for 2 titanium-oxygen interstitial solutions to about 1,600° K.

Jan 1, 1957