Search Documents

By C. W. Morris

This study was performed for the U.S. Bureau of Mines. An existing computer simulation of a dragline was modified to simulate a dragline dumping into the hopper portion of a cross-pit conveyor system. This revised computer model was then used to study four proposed cross-pit conveyor systems. Parameters such as dragline position, hopper position, and digging procedure were varied to maximize the dragline production. This performance was compared with the conventional side-casting spoil method. I t was concluded that the cross-pit conveyor systems were competitive with the conventional side-casting technique.

Jan 1, 1977

By McElroy. G. E.

"INTRODUCTION The ventilation of development faces in mines for diluting gas or dust concentrations and, in hot mines for providing air-motion cooling effect, by fan pipe units discharging high-velocity streams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, a subject on which little definite information is available. A study of the air flow from grills into rooms 3/ has provided some basic data, but under conditions no different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.The purpose of this report is to present and discuss the results of an initial series of tests of a general investigation designed to yield definite laws and design data for the discharge of fan-pipe lines in mines. This series was planned to yield preliminary data on the effects of velocity of discharge, size and shape of pipe, and adjacent walls on the air-flow distribution. Tents were made on 10-inch pine with seven different end conditions and one change of wall condition. Changes in size and shape of discharge wore made by short transformation pieces directly at the discharge end, with the result that effects due to contraction and expansion of the flow, which proved to be of much greater importance than was expected, totally obscured any normal effects due to size and shape. The results of this series of tests, therefore, relate to 10-inch pipe with various discharge designs and are so reported."

Aug 1, 1940

By James A. Wasson, Harry R. Johnson, Dean W. Boley

The Cow Run sand was cored and electrical and radioactivity surveys were made in C. E. Vandevender well 35 in the Burning Springs pool of the Burning Springs oilfield , Wirt County , W. Va . Laboratory tests , reservoir - fluid analysis , well - log interpretation , and available field data indicate that a substantial quantity of oil may be recovered from this pressure - depleted reservoir by waterflooding . Two formations erroneously believed to be the First and Second Cow Run sands were similarly evaluated in A. E. Mackintosh well 8 , Anns Run Pool , Wirt County , W. Va . , but were found unsuitable for secondary - recovery operations .

Jan 1, 1964

By Charles J. Stehlik

This report deals with the changing behavior of mine roof bolt and roof rock as a result of repetitious production blasting . Observations were made in the upper shale production headings at the White Pine Copper Co. room and pillar mine , White Pine , Mich . Roof bolt compression pads and a stratascope were used in the investigations , which were carried out in three separate test sites in which nearly identical procedure produced comparative , repetitive , and anomalous observations . Results indicate roof bolt tension change and roof quality deterioration anomalies were coincident with blasting . The hypothesized cause of the anomalies is a seismic shock generated by the blasts .

Jan 1, 1964

By R. S. Rosso

A program to investigate the effects of hardened washers on the uniformity of roof bolt tension and the resulting ground control in an underground mine was carried out. The complete roof bolt installation and roof bolt loads, mine convergence, and bed separation were monitored for a period of five months. The results show no evidence to support or refute the theory that mechanical roof bolts offer better support when they are installed with a high uniformity of tension. Also shown is the fact that if the bolts are installed with a maximum deviation from the mean torque of ±15% the addition of hardened washers significantly improved the uniformity of the installed tensions in the roof bolts.

Jan 1, 1977

By R. S. Dean

"INTRODUCTION The idea of direct steel is by no means new. Although the work of Bessemer and Siemens provided simple and effective moans for converting pig iron into steel and established the ""blast-furnace route"" as the almost universal method of producing steel, metallurgists have not ceased to dream of direct steel. By direct steel is meant any process by which iron oxide in ore is reduced to Iron of the same or greater purity than the final steel or wrought iron. That is, carbon or alloying elements would be added as needed, not reduced in unwanted quantities into the iron and then removed more or completely by refining (Bessemer or open hearth) only to be readded in desired quantities.In general, direct-steel processes are ""sponge-iron"" processes, because reducing iron oxide without simultaneously alloying the iron with carbon, phcophorus, sulfur, and silicon present in ore and fuel succeeds only if the temperature is below the melting point of the iron. Such solid iron formed by reduction of iron oxide at relatively low temperature is sponge iron, which is butlery and porous. When the reduction proceeds at the higher temperature at which the particles of metal can weld together or finally even melt to yield pellets or balls that do not have the porosity and low-density characteristic of sponge iron, the product might preferably be called simply ""direct iron."""

Jan 1, 1945

By Douglas Ketcham, Thomas Jetzer

While the neurological and vascular aspects of Hand-Arm Vibration Syndrome (HAVS) has been generally accepted as a medical condition, the medical criteria and the clinical findings used to establish the diagnosis has been more difficult to bring to consensus. The criteria was first quantified by the Taylor-Palmear scale.1 This criteria was subsequently modified in 1986 at the 1st Stockholm Workshop2,3 to included more acceptance for the neurological effects that characterized the predominate findings in some workers. The relationship between hand-arm vibration and Carpal Tunnel Syndrome was defined in NIOSH 97-1414. While the aforementioned documents have defined the clinical entities associated with hand-arm vibration exposure, agreement on the clinical findings and test to confirm the diagnosis has be been more difficult to bring to consensus. Clinicians assessing HAVS has relied on a number of varied neurological and vascular tests. The neurological testing has focused on assessing damage to the sensory capability of the fingers for the neurological component including tests to measuring ability to sense vibration, cold or other end point finger sensor functions. However, the vascular testing has been traditionally focused on the ability to either measure vascular function or to reproduce the vascular blanching that occurs in HAVS with cold water provocation. Recent assessment of this testing in the United Kingdom Coal Miner’s study has questioned the value of this testing especially in reviews by McGeoch.5 In an attempt to provide some type of definitive testing to substantiate vascular damage from hand-arm vibration exposure, angiography is an alternative or adjunct to cold water provocation testing. The standards that have been established to predict the level, type and incidence of HAVS have been based on clinical studies and reports that have essentially been all male populations. However, the recent entry of women into more vibration intensive jobs has brought about the exposure of some women to high levels of vibration previously only previously experienced by men. However, there have been only few studies that look at HAVS in women6. Although exposed the same vibration levels, it has not been clear that the latency and type of pathology of HAVS in women will be the same as for men. The purpose of this study is to look at recent case studies of men and women exposed to jobs with high levels of hand-arm vibration with extensive clinical testing for both the neurological and vascular components of HAVS as well as other associated upper extremity conditions such as Carpal Tunnel Syndrome.

Jan 6, 2006

By Lloyd A. Morley

The performance of electrical grounding systems in open-pit metal mines is evaluated, using techniques which are described thoroughly. The normal electrical distribution and grounding practices used in metallic open-pit mines are reviewed and compared with coal mine usage. The results are used to generate the included recommendations for Federal Regulations concerning open-pit metal mine grounding systems.

Jan 1, 1976

By Gerald T. Homce

A system capable of monitoring mine electrical power systems and detecting impending component .failure could significantly improve power system safety and reduce unscheduled equipment downtime. Such monitoring would require a method of evaluating electrical parameters, calculated from terminal values, for indications of component deterioration. The U.S. Bureau of Mines has targeted electrical failure of squirrel cage induction motors and examined the use of mathematical models to aid in this evaluation. The initial stage of this work is complete, and has produced polynomial networks called adaptive learning networks (ALN's) that can detect and quantify winding insulation leakage simulated on laboratory motors. In this modeling process, empirical data from laboratory motors were used to select the electrical parameters most significant for assessing? motor conditions, and mathematical expressions relating these parameters to simulated deterioration were formed. ALN's developed thus far can process readily measured motor terminal information and quantify power and current levels of laboratory-simulated leakage to within 1% and 3% of full load values, respectively, for motors in the 10-to 150-hp size range. The next stage of this research is validation of these ALN's for actual motor failures; this stage is currently underway, using accelerated life testing of laboratory motors.

Jan 1, 2010

By Roy J. Greenfield

The overall purpose of this research was to improve the understanding of how the post disaster seismic location system works, what determines the signal size, what is the character of the seismic noise, how well the system can detect blows from a trapped miner, and how well the source of the blows can be located. Based on an improved understanding of the system, improvements were suggested in the seismic subarray configuration, and in the system deployment procedures. An important part of this research was to become familiar with the seismic system operation and to work with the Westinghouse Electric Corporation and MSHA personnel to modify and improve the system. To accomplish this we participated in the planning, execution, and data analysis for a number of seismic field tests. Several in-mine field tests were conducted. From these tests the capabilities of an in-mine seismic system were analyzed and specifications were made for designing an operational in-mine system. Several portions of the work done on this grant were covered in previous reports. In particular the capabilities or the presently operational surface based seismic location system has been thoroughly documented by Durkin and Greenfield (1981). Portions of the location procedures and effects of mine openings on seismic signals have also previously been published. These portions or the work will only be summarized in this final report.

Jan 1, 1982

By Leonard Obert

THE CRACKING AND POPPING of rock, often heard by men working underground, for years has been interpreted as a warning of danger and unstable ground. However, not until 1939 was it discovered that rock under stress generates subaudible and sometimes audible seismic disturbances (referred to as "micro-seismims" 4), which can be detected with the use of a suitable seismic apparatus. Since that date laboratory and field investigations have been in progress to ascertain to what extent this phenomenon can be utilized to detect, localize, and determine the magnitude of areas of instability in and around mine openings and to predict if and when failure will occur. These investigations have included a determination of the types of problems to which the method is applicable and the effect of rock type, geological defects, such as joints, fractures, faults, and other uncontrollable factors, on the reliability of results. Six reports have been prepared covering the investigations conducted between 1940 and 1952 (4-9). 5 These reports describe some of the characteristics of micro-seismims, as determined from both laboratory and field tests; the equipment used to pick up and record micro-seismims; the general test procedure and method of analyzing results; and applications of the method to specific mining problems.

Jan 1, 1957

By E. J. Lintner

This paper is one of a series being prepared by the Bureau of Mines describing; gypsum mining and crushing methods and costs at various operations throughout the, United States. These papers are designed to dissemminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs may in many instances cause embarrassment to the individual operator as well as to the industry as a whole; on the other hand, operating costs are essential to the technical discussion and. study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulation shall ensue. The following report deals specifically with the mining and primary crushing methods employed at the plant of the Ebsary Gypsum Co., Inc., Wheatland, Monroe County, N. Y. This company is capable of maintaining a maximum yearly production of 220,000 tons of crushed gypsum, thereby ranking as one of the largest gypsum operators of the State. The methods and practices employed typify the standard methods followed by gypsum producers in western Now York State, The bed of gypsum mined lies only 35 feet beneath the surface and is above average thickness for this vicinity.

Jan 1, 1937

By Earl C. Redman

The Juneau Gold Belt, centered on Juneau and approximately 120 miles long by 10 miles wide, stretches from Berners Bay on the north to Windham Bay on the south (fig. D-l). Access within the Juneau Gold Belt is provided by the Glacier, Thane, and North Douglas Highways. The Glacier Highway extends northwest from Juneau for approximately 40 miles to Echo Cove, and the other two roads end 5.5 miles southeast and 12.6 miles west from Juneau, respectively. None of these roads connect with other highway systems and access to other areas is restricted to airplanes, the State ferry system, and commercial barge lines. BUREAU ACTIVITIES The majority of lode gold produced in Alaska came from the Juneau Gold Belt portion of the Juneau Mining District. To evaluate the economic potential of the Gold Belt, the Bureau located 173 mines and prospects within the area. A total of 263 ad its and shafts were found and 56,650 feet of underground workings were mapped. The Bureau collected and analyzed 1,557 samples during the study. In addition, considerable detailed geologic map-ping was done in the vicinity of the mines and prospects from which ore control models were developed.

Jan 1, 2012

By H. B. Brunot, L. C. IlsLey, E. J. Gleim

"INTRODUCTION To supply inspectors, safety engineers, and others with detailed information as to the safety features of the various electrically operated machines that have been approved as permissible by the Bureau of Mines, three bulletins and five reports of investigations have been published dealing with the various classes of approved machines:Bull. 313, Permissible Storage-Battery Locomotives and Power Trucks.Bull, 343, Permissible Coal-Handling Equipment Approved from January 1926 to December 1930, inclusive.Bull. 382, Permissible Coal-Cutting Equipment Approved Prior to July 1, 1932.Rep. of Investigations 3309, Permissible Electrically Operated. Air Compressors.Rep. of Investigations 3326, Permissible Electrically Operated Room Hoists.Rep. of Investigations 3345, Permissible Electrically Operated Rock-Dust Distributors.Rep. of Investigations 3363, Permissible Electrically Operated Hand-Held Coal Drills.Rep. of Investigations 3391, Permissible Electrically Operated Post Drills and Drilling Machines.The present paper gives similar information relative to the mine pumps approved before October 1, 1939."

Mar 1, 1940

By Frank H. Reed

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining , preparation , and utilization of coal . This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee , which cooperated with a counterpart British committee . The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter , Deputy Solid Fuels Administrator . The personnel of the mission consisted of H. F. Yancey, in charge , J. W. Buch, Thomas Fraser , L. L. Newman , and L. D. Schmidt of the Bureau of Mines ; H. H. Lowry , Director of the Coal Research Laboratory , Carnegie Institute of Technology; H. J. Rose , Vice - president and Director of Research , Bituminous Coal Research , Inc .; and F. H. Reed , Chief Chemist , Illinois State Geological Survey . Over 50 reports were written by the members of the Solid Fuels Mission . These , together with microfilms of supporting data obtained in the course of the investigations , are on file at the Bureau of Mines , Washington , D. C. , where they are available for public examination . The Office of the Publication Board in the Department of Commerce is prepared to furnish photolith copies , photostats , or microfilm reproduction of all declassified reports . A Bibliography of Scientific and Industrial Reports is issued weekly by the Department of Commerce , Office of the Publication Board , and is sold by the Superintendent of Documents , Government Printing Office , Washington 25 , D. C. , on a subscription basis . An initial payment of $ 10 will provide for approximately 9 months , and subscribers will be notified when additional remittance is necessary . All subscriptions will begin with volume 1 , No. 1 , unless ordered otherwise . The Bibliography, covers all materials and subjects and gives instructions for obtaining the desired items . The reports of the Solid Fuels Mission relate to the following general subjects : Mining methods in the Ruhr district of Germany , with special reference to mechanical cutting and loading equipment , pneumatic packing , and Diesel mine locomotives ; activities of industrial research laboratories supported by the German coal and coke industry ; coal preparation in western Europe ; low- temperature carbonization processes ; metallurgical coke from

Jun 1, 1948

By J. J. Forbes

The investigation of major and minor coal-mine disasters has been a routine function of the Bureau of Mines since its inception in 1910, and the facts obtained during such investigations have been used as a basis for determining the precautions that the managements and employees of many mines are observing to forestall similar occurrences. The Bureau has conducted research on roof-control and other mine problems, but a comprehensive study of other fatal accidents was not attempted until February 10, 1950, when the policy of investigating all coal-mine fatalities in the United States was approved by Bureau of Mines Director James Boyd. The investigations are being conducted by Federal coal mine inspectors functioning under the provisions of the Coal Mine Inspection and Investigation Act of May, 1941, Public Law 49; and reports covering the investigations are distributed to management, the State mine-inspection agency, and representatives of the mine workers' organization have jurisdiction at the mine.

Jan 1, 1951

In 2006, a total of 4,573 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA).1 Stone mines comprised 30.7% of all mining operations. ? Mines producing the primary commodity of limestone (crushed and broken) comprised the largest number of operations (n=2,042; 44.7%). ? Stone mining operations were located in all states and territories except Delaware and North Dakota. ? Pennsylvania had the most stone mines (n=368; 8.0%), followed by Texas (n=342; 7.5%).

Jan 1, 2008

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

Coal research and technologic work by the Bureau of Mines covers a broad program of investigation aimed at conservation and utilization of this important natural resource. Conservation is served by a constant search for higher efficiencies in mining, preparation, and use. Increased utilization is sought through various projects that probe new ways to use coal and expand existing coal markets. This report, the twenty-eighth in the series,3 gives the highlights of Bureau of Mines coal research and technologic work in 1963. The scope and complexity of the program makes it virtually impossible to report all progress on every project, even tor a 12-month period. Full insight into each project can be gained only through intensive review of basic objectives, past accomplishments, and current status of the work. Details of the work are given in numerous publications issued by the Bureau and its laboratories and centers located throughout the country.

Jan 1, 1964

By J. K. Whyatt

U.S. Bureau of Mines researchers reviewed an in situ stress estimate developed from measurements of overcore strain taken at test sites on the 7300 and 7500 levels of the Star Mine near Mullan, ID. Although the field measurements of over coring strain were found to be useful, significant deficiencies were found in the stress estimation procedure. A new stress estimate was developed incorporating statistical methods and an improved understanding of stress concentration factors for interpreting overcore strains recorded by doorstopper' cells. Spatial variability of overcore strains and the implications for stress field variability were explored.

Jan 1, 2010