Search Documents

By Walter W. Focke, Zola Kwela, Willem van der Merwe, Arao Manhique

"The advantages of the de Wet zirconium process for the manufacture of AZST from zircon sand include: Fewer processing steps; removal of radioactivity by leaching rather than by precipitation; alkali reagent recovery in the form of a sodium silicate solution that is essentially free of radioactivity; fewer waste streams and less waste to discard.Here we report on our efforts at maximizing the alkali recovery in the sodium silicate product stream: Milled zircon, d50 ˜ 9 µm, was fused with caustic soda pearls in open reaction vessels at temperatures between 650°C and 850°C. Fusion times of 1, 2, 4, 24 and 336 hours (with intermittent milling) were investigated.For prolonged fusion times the fusion products approached equilibrium compositions. However, the phases Na2ZrSiO5 and Na4Zr2Si3O12 observed at 850°C did not form at 650°C. Since they do not hydrolyse in water they limit the recovery of alkali. For 2-hour fusions a broad spectrum of non-equilibrium reaction-products, that are rich in sodium silicates, is formed. Optimum process conditions, with respect to NaOH recovery, correspond to a 2:1 stoichiometry and fusing for 2-hour at 850°C. At these conditions the alkali recovery is ca. 78% and the zirconia yield is ca. 57%."

Jan 1, 2003

By Erico Tabosa, Meng. Jun, Kym Runge, Matthew Brennan, Weiguo Xie, Dee Bradshaw

Turbulence and its distribution are of great importance in flotation cell design as they affect suspension of particles, air dispersion and particle-bubble collision rates, which in turn determine flotation performance. However, there is no mature technique to measure turbulence in three phase (liquid-solid-gas) systems such as in flotation cells. In this article, the authors present two new approaches that are suitable for measuring turbulence distribution in three phase systems and validate their applicability. The first technique uses a piezoelectric vibration sensor (PVS) to measure fluid kinetic energy standard deviation and the second technique applies electrical resistance tomography (ERT) to measure conductivity variation at a measurement position in a flotation cell. For the PVS technique, calibration of the sensor was performed to determine the values of parameters that were needed to calculate the force applied to the sensor. Then measurement was conducted in a 60L batch flotation cell and the results were compared with LDA measurement. This demonstrated that the piezoelectric sensor signal provides a good representation of fluid kinetic energy standard deviation at the position of measurement. For the ERT technique, conductivity distribution data was processed to give conductivity variations, which were then used to calculate fluid kinetic energy standard deviation at the measurement position. The spatial distribution of turbulence obtained by performing multiple measurements at different positions in the 60 litre batch flotation cell was found to agree with the PVS measurement results. These two techniques are potentially powerful tools for turbulence measurement in flotation environments, enabling a clearer understanding of turbulence’s influence on flotation performance to be determined.

Jan 1, 2014

By M. M. Moghaddam

Charge motion is of prime importance in the efficiency of comminution in tumbling mills. Since direct observation of charge shape and its motion in industrial mill are not possible, a combination of analytical and physical studies was used to determine charge trajectory. Software packages, which predict charge motion such as the GMT (Grinding Media Trajectory) only consider the outermost layer of charge (single ball) and ignore the interactions of grinding elements. In this research, the measured charge trajectory in a 1m-diameter mill with the transparent end, called model mill, was compared with that of the GMT. Four types of polyurethane rings were accurately machined to scale down the liners arrangements at two industrial mills. To explore various charge shapes and trajectories, the model mill was operated at 55, 70 and 85% of critical speed for five levels of mill filling (10, 15, 20, 25 and 30% by volume). The angular displacement of the toe, toe departure, shoulder and charge impact point were determined from the photographs taken from the model mill. New relationships to predict charge shape and charge impact points were introduced to modify the GMT results. The relationships were validated by the model mill using the new liner of the Sarcheshmeh copper complex SAG mill. The relative error of prediction was found to be 1.1%. The results indicated that when the lifter face angle increased from 7 to 30º, the distance between the charge impact point and the toe decreased from 52 to 31º for 25% filling. This meant increasing the probability of charge impacting the toe not the liner which favoured more efficient comminution practice. After converting AG mills to SAG mills on account of liner profile change, 31% increase in throughput (from 419 to 548 t/h) in addition to 4% decrease in the product size (from 516 to 496 µm) were realized which was a significant contribution in the plant performance improvement.

Sep 1, 2012

By H. J. Wu

The optimum performance in mineral processing plants usually demands the optimum size reduction, which is frequently achieved by a closed grinding circuit. Due to the difficulty associated with fine size classification, the size separation efficiency in closed grinding circuit is usually very low, which leads to huge circulating load and significant overgrinding. Recent development of Der-rick Stack Sizer has made an efficient fine size separation down to 200 mesh with a satisfactory screening capacity. With the efficient fine size separation with Derrick Stack sizer, the problems commonly associated with typical closed grinding circuit, including high circulating load and over-grinding, have been eliminated. Feedback from numerous Stack Sizer applications in iron ore industry indicated that, compared with conventional fine size classification equipment, the circulating load achieved by Derrick screen was usually decreased from approximate 300% down to 60% or so, while the iron recovery has been increased by 6% to 8% only by more efficient size separation in the closed grinding circuit. To study this phenomenon, this paper discusses the relationship between size classification, circulating load and mineral recovery in the closed grinding circuit. A simulation model to predict the improvement in the grinding circuit from more efficient screening is also introduced with this paper.

Jan 1, 2014

The ever increasing demand for energy and the progressive depletion of crude oil resources, have renewed interest in oil shale as an alternative fuel resource. Weathered oil shale samples were assembled from El-Nakheil phosphate mine in Quseir area, Eastern desert, Egypt. The oil shale samples were prepared and analyzed by XRD (X-ray diffraction), XRF (X-ray fluorescence spectrometry), and optical microscopic techniques. Rock-Eval pyrolysis and total organic carbon were used to study shale hydrocarbon potential. A leaching procedure using inorganic and organic acids was used to selectively dissolve the oil shale associated ash forming minerals. XRD results showed that calcite is the dominant carbonate mineral, whereas primary silicate minerals are quartz and montmorillonite. SEM (Scanning Electron Microscopy) observations indicated that the organic matter is dispersed throughout the rock matrix. The acid soluble fraction upon leaching was determined to be 37.59 and 42.74 wt% by using 5% HCl and 10% HCl, respectively. The TOC was increased from 20.78 to 29.88 and 34.09 wt% by using 5% HCl and 10% HCl, respectively. Keywords: el nakheil oil shale, characterization, xrd, xrf, sem, elemental analysis, proximate analysis, ultimate analysis, thin section, rock eval pyrolysis, acid leaching

Sep 1, 2012

By Richard K. Komarek, Antonios Zavaliangos, Roman T. Dec

Roller presses are widely utilized in mineral industry for fine milling and compaction. Recently used models are providing only limited information about the material behavior in the roll bite. This paper introduces a 2-dimensional finite element model for analyzing those two basic processes. A pressure-dependent plasticity model with linear elasticity was used as a constitutive model for the particular material. Coulomb friction law was used to describe phenomena on the material/roller surface interface. Two basic roller geometries are considered: smooth (used for milling and compaction) and with cavities, commonly used for briquetting. Comparison of the results obtained from the model with experiment indicates that they are following the general trends of experimental values recorded with laboratory roller presses. It is shown, that the model is suitable to analyze material behavior through all stages of the rolling process: feeding zone, nip region, neutral plane and release section. It can predict pressure, shear stress, slip of the material over the roller surface, material velocity field, failure of the compact during release and the course of other important process variables. This allows the process engineer to gain an improved understanding, leading to a better process and equipment design and control.

Jan 1, 2003

By Y. X. Li

In order to control the pulp level in flotation column which has long time-delay and great inertia, and is difficult to establish an accurate mathematical model, a Fuzzy-PID dual mode controller is applied. This method takes advantage of both strong flexibility and good reliability of fuzzy logic and high precision of PID. With the very stable and reliable process instruments, the control system has a good control performance and results the stable control of flotation column.

Jan 1, 2014

By M. R. Garmsiri

With the environmental issues and water recycling becoming more significant, the development of deep cone thickeners has improved the efficiency of thickening. While deep cones performance is dependent on many factors, the sensitivity of an industrial thickener to each variable factor has not been determined. In this work, four industrial deep cone thickeners, which are used on tailings stream in Shahrebabak Copper Complex, were monitored for a year to analyze the effectiveness of different factors affecting the performance. Feed flow rate, fine fraction of the feed, solids concentration, flocculant dosage and concentration, solids density, pH, temperature and bed height were the factors investigated on the basis of partial R2 and partial correlation. Results indicated that, with positive effect, feed slurry dilution affected the dewatering efficiency most sensitively. With a negative effect, the sensitivity of dewatering efficiency of deep cone thickeners to flocculant dosage was negligible. While, decreasing flocculant solution concentration had a considerable positive effect.

Sep 1, 2012

Electrochemical behaviors of synthetic and natural enargite in buffer solutions have been investigated using open circuit potential, stationary polarization and cyclic voltammetry as functions of solution pH, scan direction, scan range, scan rate and dissolved O2. The results indicate that the electrochemical behaviors of synthetic and natural enargite are very similar; solution pH, scan direction, scan range and scan rate have remarkable effects on the electrochemical behavior of enargite while dissolved O2 has little effect on the electrochemical behavior of enargite. The potential range in which enargite possesses the ability of passivation is from ?0.9 V to + 0.83 V vs. SCE. Enargite is most stable in neutral and alkaline solution around potential ?0.2 V vs. SCE. The main oxidation products on enargite surface in alkaline solution are Cu(OH)2 while the potential imposed on it is within the range of ?0.2 V to 0.33 V vs. SCE and Cu(OH)2 + S0while the potential applied is higher than 0.52 V vs. SCE.

Jan 1, 2014

By M. Guo

Coal-based Direct Reduction in Interior-combustion Shaft Kiln (CDR/ISK) is a brand-new technique. Compared with the traditional Coal-based Direct Reduction (CDR) technique, its main character is to use Interior-combustion Shaft Kiln (ISK) as the reactor of direct reduction. After being crushed and grinded, iron ore is made into green pellet, which will be surface-coated by coal fines. Then, the surface-coated green pellet can be directly reduced in ISK. The pellet should not be too dry and should be charged from the top of ISK. Oxygen-contained air should be blasted into ISK to keep the temperature in it higher than 1000 degrees centigrade, at which iron oxide will start direct reduction. The reduced pellet will be discharged from the bottom of ISK and after de-surface-coated, spherical Direct Reduced Iron (DRI) can be gained. The volume of carbon monoxide in the off-gas discharged from ISK is less than one per cent. By using this technique to get one tonne DRI, the consumption of coal is about 300kg of fixed carbon, which is much lower than the energy consumption by using other CDR techniques. There is a lot of complex refractory iron ore in China, which remains unexploited. The iron-bearing minerals in this kind of the iron ore can not be beneficiated economically by present technique of gravity, magnetic, flotation or magnetic roasting because the iron minerals are too very finely disseminated to be liberated, or, the iron minerals are too similar to gangue to be separated each other. By using CDR/ISK, complex refractory iron ore can be directly reduced in lower temperature and all kinds of iron mineral can be turned into iron metal. As the grains of iron metal growing larger during direct reduction, magnetic separation can be used to separate iron metal from gangue mineral, thus high-grade iron metal fines can be gained. According to the experiments, the grade of iron metal fines is above 90 percent and the recovery of iron is higher than 90 percent. The consumption of coal to process one tonne of complex refractory iron ore is only about 90kg of fixed carbon.

Jan 1, 2014

By H. Sarvamangala

Selective separation of alumina, silica, calcite and apatite from hematite was achieved through microbiologically induced flotation and flocculation in presence of bacteria (B.subtilis) and that of hematite from apatite after interaction with yeast (Saccharomyces cerevisiae). Bacterial and yeast metabolites containing extracellular proteins were characterized from mineral-grown cell free extract. Bacteria and yeast can adhere to mineral surfaces and influence subsequent separation of the minerals. Bacteria functioned as a stronger depressant for hematite, while yeast cells depressed apatite at neutral pH. Selective affinity of the bacterial and yeast cells towards the mineral surface was observed through adsorption studies. Extracellular proteins (EP) were isolated from B.subtilis and yeast. The protein profile of the EP of bacterial and yeast cells grown in presence and absence of minerals was studied. This study has demonstrated the utility and amenability of microbially-induced mineral beneficiation of iron ores through bacterial and yeast cells and their metabolic by products.

Sep 1, 2012

By M. Kargar Razi

According to the unique properties and many applications of nano gold powder, it was prepared from an acid leaching tail solution. The low value residual gold ions were existed in acid leaching tail solution in Mouteh gold mine in Iran with fellow heavy metals as pollutants (FeP2+P, Cu P2+P, and ZnP2+P). Preparation of nano gold particles is achieved by two steps. First, by addition of ammonia as separation step and second using suitable reagents for precipitation/extraction step. Conditions control includes pH, residence time, temperature, agitation, and molar ratio of reducing agents to reagents. The optimum results show that nano gold powder was prepared by temperature of 250 °C, urea to gold molar ratio of 3:1, and reduction time of 20 min. Also, heat treatment improves dispersion of nano sized gold particles. The properties of gold nano powders were evaluated by SEM, A.A, and UV- Vis spectroscopy methods. The size of prepared particles were about 80nm to 90nm.

Jan 1, 2014

By Diogo R. Prado, José Aurélio M. da Luz

Drying operation can have a major importance in a mineral processing undertaking. The proper sizing of dryers can ensure the specified dewatering level without energy wastage. However, often the sizing of fluidized bed is done disregarding the actual residence time distribution (RTD) of the particles inside the reactor. In this case it is usual to adopt the average residence time as a design criterion. In this work, we have quantified the effect of residence time distribution on drying, ensuring that a previously adopted fraction of the particles remains inside the reactor for the required time lapse needed for drying. Design criteria such as particulate flow rate and drying time, taking into account the statistical distribution of residence time was studied, matching the thermodynamic and fluid dynamic aspects of the drying process. Experimental tests carried out have confirmed the RTD for a teetering bed as the same for a canonical ideal mixing system. Although the fluidized bed volume using the proposed formulation was higher than that found for the average time based procedure, the efficiency gain in drying has proven advantageous.

Jan 1, 2014

By Kumar Ashish, Shukla Akhilesh, Kr. Rokkam Kiran, M. Sheeba, S. Sombhatla Sundar

"Purification of zinc leachate plays a predominate role in zinc leaching refineries, to produce impurity free cathode sheets. As a part of such purification sequences, copper cementation with zinc dust is the preliminary step, since the presence of copper will preferentially deposit during zinc electro deposition and has the effect of reducing current efficiency. The cake thus produced is being accumulated as an inventory, due to invariable market and leading to space constraints & hazardous ambience. Hence, a project has been taken up for in-house generation of copper sulphate solution through ammonical leach followed by solvent extraction process and utilizing it as an active promoter for zinc sulphide flotation in Hindustan Zinc’s own captive mines. Cold purification cake majorly contains copper (30-40%) along with zinc (10-20%) and cadmium (2%). Confirmation to the above statement, photomicrographs of purification cake also confirmed the major presence of copper in metallic or oxidized form. In present work ammoniacal carbonate leaching of purification cake followed by solvent extraction using diketone based solvent has been studied under the influence of various parameters viz., temperature, agitation, pulp density, ammonia, CO2 dosages, solvent concentration, and impact of w/s zinc on leaching and solvent extraction. Leaching kinetics determined based on shrinking core model. Chemical reaction at unreacted core was found to be the rate controlling step. The estimated activation energy was found to be 24 KJ/mol. Leached copper has been extracted by solvent extraction with a ß diketone based solvent and is stripped with sulfuric acid as concentrated copper sulfate solution. The above established R&D findings are successfully implemented in the Commercial plant with a treatment capacity of two tons of cold purification cake per batch. Till now 500 MT of Purification cake has been treated, and generated 6500 MT of copper sulphate (55 g/l Cu), with final Cu recoveries between 87-90%."

Jan 1, 2018

By J. Yvon, Inna V. Filippova

"The aim of this work is to seek the inhibitors of the meteoric and bacterial dissolution of sulphides and gangue minerals to stop the undesirable chemical reactions during conservation of the flotation wastes. The approach of passivation of surfaces by chemical treatment of the solid phase is applied for this objective.The samples taken from different depths of an old French waste dump revealed the capacity of the flotation tailings to produce acid waters (pH 1.8-2.4) and to release heavy metals. Mineralogical studies show not only the product of sulphide oxidation, i.e. sulphates, but also the complex transformations of aluminosilicates in acidic liquid phase. The detection by XRD of aluminium hydroxides (gibbsite, boehmite) allows supposing the recrystallisation phenomena during tailings conservation.Comparative tests of the passivation of the surface of sulphide minerals and waste of flotation with using of conventional reagents (CaO, NaOH, phosphates) and original reagents for this purpose (alkyl dithiocarbamates) allow to identify the optimal treatment conditions and the efficient chemicals.Leach tests were carried out in percolation columns during 68 weeks. The normalised leaching tests according to French legislation were run to confirm the selected treatment conditions. The results obtained show that a single treatment with carbamate inhibits the oxidation of the pyrite and the other sulphides, and totally prevents the formation of acid waters (the stabilised pH was 5.3-5.8). Treatment of in situ drainage water allows to obtaining a total precipitation of heavy metals: the residual concentrations of Fe, Cu and Zn are lower than 0,1 mg/l.The passivation of sulphides is the result of the formation with carbamate (studied by IR spectroscopy and XPS) of organometallic compounds, which are stable in acid medium. The presence of thiuramdisulphide (product of alkylcarbamate oxidation) at the mineral surface stabilises the mixed adsorption layer and leads to a considerable reduction in the hydratation rate of surface by avoiding the corrosion of the pyrite. No aluminium was detected in leach solution with this treatment."

Jan 1, 2003

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By Yongfu Yu, Xiaotie Wang, Fuguang Zhang, Liping Che

"The flotation process of native Rare Earth minerals such as bastnasite, monazite, mixed minerals of bastnasite and monazite, using the new effective collector Dh was studied in this paper, respectively, and the flotation properties are described. The good qualities of the new collector Dh were revealed through comparing with other collector of Rare Earth minerals. The test results of different ore samples show that at moderate pulp pH (8.5-9.5), Rare earth minerals can be effectively separated from barium, calcium and silicon bearing intergrowth minerals (barite, calcite and silicate minerals) and high quality Rare Earth concentrates can be obtained successfully by the new collector Dh, acid silica gel, turpentine and reagents fitting together rationally. In order to determine optimum technical conditions, the effect of pulp pH, pulp temperature, pulp density and the effect of dosage of reagents (Dh and acid silica gel) on the flotation were investigated in the test.Simultaneously, the paper explores the mechanism of the flotation of Rare Earth minerals from intergrowth minerals. The infrared spectra for Dh and Rare Earth cation by analysis in theory shows that Dh formed chelate complex with Rare Earth cation and were adsorbed on the surfaces of Rare Earth minerals. The mechanism of the intergrowth minerals depressed by acid silica gel can be explained as gummy colloid hydrolyzed from acid silica gel which are selectively absorbed on the gangue minerals, making them hydrophilic and depressed, with pulp pH value of alkalescent."

Jan 1, 2003

By Y. S. Sun, P. Gao, Y. F. Li, J. W. Yu

"Oolitic hematite ore is one of the most refractory iron ores in the world. It is not feasible to separate iron minerals from raw ore by conventional mineral processing methods. In recent years, a new technology called coal-based reduction followed by magnetic separation has been employed to produce metallic iron powder from oolitic hematite ore effectively. In order to find the nucleation mechanism, a thermodynamic analysis of the carbothermic reduction of oolitic hematite ore was conducted by the HSC 6.0 thermochemical software. The phase transition and microstructure changes during the coal-based reduction were also investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the iron oxides in the oolitic ore were reduced to metallic iron following the route of Fe2O3–Fe3O4–FeO–Fe in reduction process. The reduction reactions preferentially occur in the high activity regions to form a higher concentration of Fe elements, and then more supersaturated Fe separated out to form new phase nuclei. Under the action of homo-aggregation and principle of minimum free energy, the iron cores continuously absorbed migratory Fe around and grew into quasi-spherical iron particles embedded in slag phase. INTRODUCTION With the rapid increase of steel industry, premium grade iron ore in China has been gradually exhausted, and its supply has become bottleneck for the development of iron and steel industry (Guo et al., 2015). Therefore, it is urgent to exploit the refractory iron ores, such as oolitic hematite ore. Oolitic hematite ore is widely distributes in France, Germany, America, Canada, Pakistan, China, and among other countries (Maynard and Van Houten, 2004; Li et al., 2011). In China, the explored reserve of oolitic hematite ore is 3.72 billion tons, which accounts for approximately 1/9 of total iron ore resources of China (Gao et al, 2016). Oolitic hematite ore possesses complex composition,"

Jan 1, 2018

By S. M. Saghaeian

The studies on the product finer than 12 mm due to crushing and sizing plant of Gol-e-Gohar Iron Ore mine showed which this material contains significant amount of valuable iron minerals. Based on the carried out experimental studies on representative samples of fine hematite iron ore, a processing flow sheet was designed to upgrade iron content. This plant is known as first hematite iron ore enrichment plant in Iran which the dry medium intensity magnetic separators (with magnetic field intensity 4500 gauss and high gradient) has been used. The main objective of the plant is production of high iron product with iron content more than 61% and weight recovery more than 55% from the feed with iron content of 54%. In this plant, at first material are screened by a single deck screen (6mm), then oversize particles is separated at one stage by magnetic separator, while undersize ones at two stages. Based on the results of experimental tests, a final high iron product with iron content of 62.4% and weight recovery 63.9% can be achieved. It should mention which the iron content can be enhanced through increasing the speed of magnetic separators especially at the part of separation of finer iron ore.

Jan 1, 2014

By Yuexin Han

The wet preconcentration of haematite, comminuted by high-pressure grinding roller was studied, using the cylindrical ferromagnetic medium. The effects of various factors including rod diameter, rod gap and background magnetic field intensity (BMFI) on the performances of preconcentration for different size fractions and the force analysis of single mineral particles with different diameter in the separation zone were emphatically investigated. The results showed that as the rod diameter increased, the rod gap decreased, and the BMFI increased the tailings grade and the tailings yield reduced while the concentrates recovery raised that was regardless of variations in feed size distribution. For the -3.2+0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 7 mm at BMFI of 454kA/m is used to get a higher performance. For -0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 4 mm at BMFI of 263kA/m is used to get a higher performance. After the classifying preconcentration, at the optimum condition, the overall concentrate grade increases by 9.56 percentage points and the concentrate recovery is up to the 82.67% with a tailing grade of 10.68% and a tailing yield of 40.31%. The magnetic force, exerted on weekly magnetic minerals was proportional, to the specific susceptibility and square of BMFI. For the same BMFI, the magnetic capturing force on coarse particles increased, and that on fine particles decreased with the increasing of rod diameter. For the lean locked-particles, considering the gravity and viscous resistance of particles, rods with a big diameter were beneficial to the capture of coarse particles and had no influence on the capture of fine particles, while rods with a small diameter were good for the capture of fine particles and not suitable for the capture of coarse particles of lean locked-particles. Keywords: low grade haematite, high-pressure grinding roller, high intensity magnetic separation, pre-concentration

Sep 1, 2012