Search Documents

By M. Mirzazadeh

Air cooled crackable and conventional forged steel specimens were tested under reversed push-pull conditions to examine the effect of shot-peening on their high cycle fatigue behaviour (-106 cycles). The steels were tested in the normalized as well as shot-peened conditions. The results showed that shot-peening smooth specimens had little effect on the fatigue limit of the air cooled forged steels and the detrimental effect of the rougher peened surface was not apparent. Microhardness profiles indicated that the shot peening produced a gradient of compressive residual stresses that was greater than that of the loading stresses, suppressing the anticipated beneficial effect on fatigue life. Crack initiation was more likely to occur below the surface. The results indicate that the surface roughness was not a significant factor in controlling the fatigue lives, since they were essentially the same for the non shot-peened and shot-peened steels.

Jan 1, 2010

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

Induced microseismicity monitoring is: ?Essential tool in improving the geotechnical understanding about a mine and its inaccessible surrounding rock masses. It helps to determine: -Event timing, location, and magnitude - identification of highly stressed areas -Event source mechanism - the physics of fracturing in its seismic source region -Seismic strain-rate distribution in 5D - identification of stress concentration or migration patterns -Geomechanical interpretation - identification of hidden geological structures or weaknesses in the ground -Strategy for mining e.g. by a block caving method - maximization of mine production and to optimize ground support design -Potential of future seismic hazards -Large event re-entry protocol, to improve mine safety ?The norm as part of mine safety maintenance and long-term mine design practices

Aug 1, 2013

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

By Martin Bergeron

Producteur d?or de taille intermédiaire Mines Aurizon Ltée Bureau-chef àVancouverMine et projets localisés au Québec2

May 1, 2011

By Keith Donovan

Why are we here? Improve equipment performance & health ? Eliminate undesirable downtime and expensive secondary damage ? Maximize equipment life, optimize running costs (reduce costs) ? Improve safety and environmental performance ? Capture and consistently apply equipment knowledge ? Improve Proactive Maintenance processes & practices

May 1, 2009

By J. ?H. Chen

Remote sensing technologies have been applied to numerous fields and already benefited those in improving efficiency and recognition accuracy. Change of streamflow can be devastating to residents living along riversides. Still it is difficult to detect such deathly change in large area scale by traditional field surveys. The research aims at provision of detecting streamflow change using a mathematic method based on remote sensing technologies. The scope is on remote sensing stream images taken during the invasion by Typhoon Morakot, bringing one of the major catastrophes to Taiwan. An algorithm was adopted to deal with streamflow recognition on RGB images. The algorithm is capable of yielding change measured by meters and illustrates how main streams shift. An practical example for the Baolai area surrounded by Laonong stream shows that the streamflow moved 88 meters (36 pixels) toward the downtown area during the invasion by Typhoon Morakot. In addition, the results highlight all dangerous zones (scouring zones) for residents to prevent further potential damage.

Aug 1, 2013

By J. G. Kelly, C. P. Brown

"In June 1983 a new borehole hoisting system was commissioned at Sherritt Gordon's Fox Mine. Twelve hundred tons-per-day of ore from the 2600 and 2800 levels are being hoisted to the 2000 level through an 8-jt diameter bored winze. This new method replaces the diesel truck haulage system which had been in operation at the mine since 1975.A study was initiated in 1980to determine the most effective method of achieving the required production. The study examined several hoisting alternatives including: expanding the existing trucking system; converting to electrically -powered truck haulage; and deepening the skip compartments of the existing main shaft. The alternative selected as the hoisting method most suited to the requirements was borehole hoisting.Development of the new system commenced in April 1982. Underground excavations included 700 feet of 8-ft diameter borehole, a hoistroom and headframe, storage bins, and a grizzly and rockbreaker station. Equipment installations included: a 5-ft diameter double-drum Nordberg hoist; a counterweighted Kimberley-type skip; two rockbreakers; and the steel sets in the winze. These installations were completed in June 1983. Some problems were encountered after the initial commissioning but these were solved, and since August 1983, the system has proven that the designed capacity is achievable within expected costs."

Jan 1, 1985

By J B. McConnell

The Thompson smelter has three unique features which form the basis ~f its design: fluid bed roasters which treat nickel concentrate filter cake from the mill, as well as the flux, in order to achieve partial desulphurization; the use of electric furnaces for the smelting of the partially desulphurized, preheated roaster product; and the disposal of slag by water granulation and slag slurry pumping. The installation consists of three fluid bed roasters, each feeding an electric furnace. Nickel concentrate is received at the smelter via pipe line. It is thickened and filtered, and the filter cake, together with siliceous flux, is fed through rotary bin feeders and reciprocating double-gate seals into the fluid bed roasters. Air injected into the roasters through club-head tuyeres oxidizes part of the sulphur and associated iron in the concentrate. The heat of reaction dries and heats the charge. Roaster product is recovered from the gas stream in cyclones and from the roaster bed through automatic valves.

Jan 1, 1963

By Richard W. Hutchinson, Christopher Osterman

Abstract -The Selebi-Phikwe deposits are hosted by amphibolite to granulite facies gneisses of the Limpopo belt. The sulfide orebodies are generally stratiform and conformable to the foliation of the wallrock gneiss. Sulfide remobilization has occurred during metamorphism and has produced discordant sulfide veins, called piercement structures, which project into the hanging wall and foot­ wall gneisses. These piercement structures are compositionally similar to the stratiform sulfides, consisting mainly of pyrrhotite, pentlandite and chalcopyrite. However, texturally the piercement sulfides are coarse grained and inclusion-free, whereas the stratiform sulfides are fine grained and packed with tectonically produced wallrock inclusions. The piercement structure sulfides and adjacent stratabound sulfides were sampled and analyzed for major base metals and PGE's for comparative purposes. Most of the piercement structures were enriched in Cu, Ag and Au, whereas they were generally depleted in Ni, Co, Fe and PGE's. Changing elemental associations were observed from the stratabound sulfides and along the length of the piercement structures. This and the degree of depletion or enrichment of various major and minor elements in the sulfide piercement structures may reflect the relative mobilities of metals under metamorphic conditions. The similarities between sulfide piercement structures and the footwall Cu-POE veins in some Sudbury deposits are reviewed.

Jan 1, 1994

By S. P. Lowe

Introduction In the following pages a general description is presented of the concentrator and cyanide plant of the Hudson Bay Mining and Smelting Company, Limited, at Flin Flon, Manitoba, together with some account of the steps which have led to the adoption of the present practice. For an account of the preliminary test-work and pilot-mill operation, the reader is referred to a recent paper by R. E. Phelan on the History of Flin Flon Mine up to Construction (1). Additional notes may be found in a paper which the writer presented at the Annual Meeting of the Institute in 1930 (2). The first ore was crushed in the present plant on July 1st, 1930, and the first ball-mill was started one month later, on August 1st. Since that time, production has been continuous with the exception of one month lost during a strike in the summer of 1934. There have been no major changes in equipment or methods of treatment since the present plant was built, but many minor changes have contributed to the improvement in results obtained and to the increase in capacity to the large tonnage now being milled. The accompanying flow-sheets indicate the equipment used in the several plants, with the average life and repair cost. As originally built, the concentrator was to treat 3,000 tons per day, but the capacity has been increased to 4,400 tons. The methods adopted to make possible this increase in tonnage will be referred to below. It was the intention to produce two classes of ore: (1) a heavy sulphide, and (2) a disseminated ore. The mill was consequently divided into two sections, each adapted for most efficient treatment of one particular type of ore. However, it was soon found that it would be impossible to mine the two classes of ore separately, so it was decided to treat open-pit ore, which varies greatly in character, in the sulphide section, and underground ore, which is fairly constant, in the disseminated section. This segregation is still maintained.

Jan 1, 1935

By Christiaan Zeilstra, Jan van der Stel, Koen Meijer, Gerard Louwerse, Tim Peeters

The steel industry is producing about 5% of the world wide CO2 emission. Therefore the European steel industry has defined a research program to reduce the CO2 emission by 50% per ton: ULCOS. Since its start in 2004 ULCOS has identified four technologies for further development. Two of these technologies which produce liquid hot metal are discussed. The ULCOS blast furnace is based on recycling of decarbonated topgas and the capture and storage of CO2. The concept has been demonstrated during three campaigns at LKAB EBF in Luleå, Sweden. The smelting reduction process HIsarna is a combination of the cyclone-technology and Hismelt. The process has been demonstrated successfully in four campaigns at a pilot installation on the IJmuiden steelmaking site.

Jan 1, 2015

By Marko Lampi, Ross Andrews, Jouni Pihlasalo, Robert Matusewicz

With widespread discussion on reducing carbon, sulphur and other emissions, use of sustainable energy sources and the pivotal circular economy theme, consideration needs to be given to pyrometallurgical operations broadly and more specifically, non-ferrous metallurgy. These themes present a number of challenges in terms of current operations and the view of processing the metals which are largely taken for granted in day to day living. This paper considers how these themes will impact pyrometallurgical flowsheets using the non-ferrous base metals as an example. It will examine the flowsheet chain to offer views on the boundaries of flowsheet optimization and the application of available tools to meet these future goals and challenges. INTRODUCTION The themes of reducing footprint through lowered CO2, S and other emissions, together with process sustainability (e.g. lowered energy) and links to the circular economy are well known to everyone in the metals industries. Whether it is reducing greenhouse gas emissions or analysing the importance of metals recycling in the circular economy, all these themes carry with them the fundamental premise of any change being considered; how can you best optimize a system to meet your aims? Of course, this depends on the available tools and the approach used for optimisation.

Jan 1, 2019

By A. Bouchard

"Based on laboratory testwork, a two-stage cleaner / re-cleaner circuit with feed regrind was proposed to replace an existing single-stage middling circuit treating a scavenger concentrate at Inco’s Clarabelle mill. In order to effectively transfer the technology and implement the new flowsheet in the plant, an extensive on-site pilot plant campaign was conducted. After demonstrating the improved metallurgy, the two-stage middlings circuit was successfully implemented at the operation.The present paper describes the on-site pilot plant testwork and the plant metallurgical improvement after implementation of the new middlings circuit. The addition of TETA / Na2S03 greatly enhanced the pentlandite selectivity against pyrrhotite and the two-stage cleaning considerably improved the pentlandite selectivity against rock minerals. The improvement was immediate after the installation of the new middlings circuit. Size by size recovery analysis indicated that a finer regrind would further improve the metallurgy of the new two-stage cleanerhe-cleaner circuit and those modifications are in progress at the mill.INTRODUCTIONThe milling operation at Inco’s Clarabelle mill has been described elsewhere (Kerr and Kipkie, 1985; Agar, 1991). While maximizing the recoveries of chalcopyrite (Cp) and pentlandite (Pn), continuous effort has been directed toward improving pyrrhotite (Po) and rock minerals (Rk) rejection. Inco discovered diethylene triamine (DETA) and triethylene triamine (TETA) (Marticorena, et al., 1994) for pyrrhotite rejection. Falconbridge further improved pyrrhotite rejection using DETA and SO2 (Kelebek, et al., 1995). No special technologies are used in the rejection of rock minerals."

Jan 1, 2001

By G. M. Dunn

Pressure leach autoclave circuits are employed in the leaching of ores, concentrates, mattes, alloys and intermediates for the recovery of metals into solution. Once the metals are extracted into solution the value metals can be recovered by hydrometallurgical means such as by purification followed by electrowinning, hydrogen reduction, pyrohydrolysis, crystallisation and other unit operations. In many of these integrated flowsheets the pressure leach step is pivotal to the recovery of the value metals from the host material. In an expansion or a new project, a large component of the capital cost can be associated with the pressure leach step and process engineers frequently look for opportunities to mitigate costs. This paper examines a new route for increasing the capacity of an exothermic pressure oxidation leach for sulphide concentrates, sulphide and phosphide mattes and alloys.

Jan 1, 2004

By W. J. Mcgaughey, M. A. Vallée

"Abstract -The application of geophysical technology to resource delineation aims to improve the quality of resource/reserve estimates by integrating high-resolution survey methods, geophysical modeling and inversion with three-dimensional representations of geological and mineral deposit data. The use of geophysics can cost-effectively improve a geological interpretation based only on geological and sampling data. Success depends upon the ability to use geological visualization and modeling software, first to develop a three-dimensional geological model and then to modify it interactively by integrating geophysical data with the geological and sampling data.The high resolution required for mineral delineation geophysics results in a focus on borehole seismic and high-frequency electromagnetic methods. Borehole wireline logging is used to develop an understanding of the relationship between physical properties and geological description. Data from core samples and borehole wireline logs allow the construction of a three-dimensional physical property distribution, consistent with the existing geological interpretation. The three-dimensional physical property distribution is used for both geophysical forward modeling (to compare to field data) and as a starting model in iterative inversions.Advanced visualization techniques allow the simultaneous viewing of the three-dimensional physical property model, the geological information and data from which it is derived, and the geological interpretation and the geophysical results. Geophysical results may be simulated responses from a forward model or the output from a numerical inversion in the form of an updated physical property distribution. Iterative refinement of the geological interpretation is required to ensure consistency with the geological and geophysical data. The key to success with this approach is that all relevant geological, geophysical, and rock property data reside in a common, visual model of the earth.Examples from massive sulfide deposits illustrate the benefits obtained by the integration of geophysical and geological data."

Jan 1, 1998

By J. A. González-Anaya, F. Nava-Alonso, O. Alonso-González, F. Alvarado-Hernandez, A. Uribe-Salas, C. Jimenez-Velasco

"One of the most common hydrometallurgical methods for precious metal extraction is cyanidation. The effluents of this process may contain relatively high concentrations of copper, zinc and iron, which react with free cyanide to form complexes, adversely affecting the efficiency and the economy of the process.This preliminary work studies the use of the solvent extraction technique to remove copper, zinc and iron cyanide complexes from a synthetic solution similar to that of gold mill effluents, in order to allow the recycling of the solution back to the process. For the extraction of these anions (Cu(CN)2 -, Cu(CN)3 2-, Cu(CN)4 3-, Zn(CN)4 2- and Fe(CN)6 3-), trioctyl methyl ammonium chloride (Aliquat 336) was studied as extractant, using nonylphenol as modifier in the organic phase (iso-octane). The experimental results showed that for a synthetic solution containing 450 mg/L total cyanide, 160 mg/L copper, 50 mg/L zinc and 51 mg/L iron, it is possible to extract the 96% of copper, 91% of zinc and 75% of iron when using 0.011 mol/L of Aliquat 336 (organic/aqueous volume ratio (O/A) =1) in the pH range of 9-10."

Jan 1, 2014

By Shila Jafari, Mari Lundström, Aleksei Kritskii, Pia Sinisalo

A typical process adopted at nickel plant is the processing of nickel-copper mattes and converter mattes using the following technology: pressure oxidative leaching (POX), solvent extraction (SX), electrowinning (EW), cobalt recovery, and solutions purification. As a result of multi-stage atmospheric and autoclave process leaching, copper-nickel separation is achieved. Cobalt and nickel are further separated by SX. Copper in the process can be removed as copper cake (Cu-cake), which is a by-product with high content of valuable metals. In the current paper, a method combining atmospheric and pressure leaching of Cu-cake in sulfuric-acid media is discussed. Suggested method allows to obtain high copper extraction (>98%), with leach residue containing precious metals and PGMs. Sulfuric acid media was chosen to make the suggested technology adaptable for the primary POX-SX-EW circuit. The initial Cu-cake was analysed and a range of process parameters (t = 25–190°C; PO2 = 0–7 bar) investigated to achieve the optimal conditions for leaching process at the ambient as well as at increased pressure. As a result, an initial process block diagram for the treatment of Cu-cake with high copper leaching efficiency and low metal losses is provided. INTRODUCTION The conventional technology for nickel sulphide ore processing includes the following main stages: froth flotation, matte smelting and converting. The subsequent processing of nickel converter matte is possible using fundamentally different approaches - hydrometallurgical (Llanos, Queneau & Rickard, 1974; Rademan, Lorenzen & Van Deventer, 1999; Kshumaneva, Kasikov, Neradovskii & Belyaevskii, 2009; Dutrizac & Chen, 2013) and pyrometallurgical (Tsymbulov, Knyazev, Tsemekman & Golov, 2007). Hydrometallurgical approach in comparison with pyro-process has several advantages, such as reduced environmental load, reduced PGM losses, increased copper and nickel extraction. Typically, hydrometallurgical technologies include leaching, solvent extraction as well as nickel and cobalt recovery in metallic form by electrowinning or hydrogen reduction or as valuable metal salts via crystallization process (Crundwell, Moats, Ramachandran, Robinson & Davenport, 2011).

Jan 1, 2019

By S. P. Chong, N. C. Shih, G. A. Turner

Fine powders, with the bulk of the particle diameters Jess than 10 microns, were aerated so that each particle was, on the average, separated from its neighbours by 1.3 to 2 mean diameters. In this state, measurements were made of the viscosity and settling rate of the powder, and the interfacial tension between it and a moist pellet. From the viscosity measurements, qualitative analogies are drawn between the behaviour of the aerated powder and that of a dense gas near its critical point.

Jan 1, 1970

By Matt Manson

Renard?1-10 kimberlite pipes and ?Lynx-Hibou?kimberlite dyke system within ?Foxtrot?property 50/50 JV with SOQUEM, Stornoway operator 2001: Discovery of the Renard kimberlite pipes 2003: Discovery of the Lynx-Hibou kimberlite dykes 2006-2007: Bulk sample program 2008: First 43-101 Resource and Preliminary Assessment 2009/2010: Updated 43-101 Resource

May 1, 2010