Search Documents

Computer-based block modelling of orebodies is now used at Renison Tin mine for the estimation of ore reserves. It is considered that this has resulted in improved reserve estimation for complex 'stratafault' orebodies. The results for all orebody types are more easily understood by the mine planning section and provide greater scheduling capability than those from the previous manual isoline reserve estimation method. A structural overview of the deposit can be gained by combining geological block models for the various orebodies. It is anticipated that upon completion of block modelling for all the orebodies the time spent on the annual ore reserve estimate will be significantly reduced.

Jan 1, 1990

Most text books on rock blasting claim that the relationship between burden and borehole diameter is linear. The statistical calculation presented here with real values from one hundred open pit and underground mines indicates that the relationship is exponential. For underground mines the burdens are consistently lower than those for open pit mines because of higher ore densities, greater confinement in blasting, and finally greater demand for well fragmented rock. The results shown in this paper are recommended to be considered in basic teaching of rock blasting technique. The formulas can be used for a first rough estimation of practical burden and spacing. The formulas do not however give any information about the fragmentation. For that purpose it is necessary to use other formulas not described in this paper.

Jan 1, 1990

By Cleghorn JH

Underground mining operations on Kalgoorlie's Golden Mile were suspended in 1976, suffering the combined effects of low gold prices and grades. A subsequent substantial increase in the gold price led to the decision by Kalgoorlie Mining Associates to reopen their mines in 1979. The two shafts selected for access required excessive maintenance. The geological assessment and development parameters prescribed have been successfully used to establish reserves to maintain production at a 390 000 tonnes per annum rate. While ore reserve grade is being maintained from primary stoping sources, supplementary lower grade ore is drawn from remnant pillars and stopes at lower cost.Performance by the workforce has reached levels previously attained and a record tonnage was hoisted in the fourth year after recommencement.Keywords : Golden Mile lodes, geological research, payruns, cut and fill, mill holes, gold price, ore grade, amalgamation.

Jan 1, 1984

Digital computers, by virtue of their capacity for high speed repetitive calculation at low cost, are finding increasing application to routine calcula- tions in the mining industry. In this paper techniques are shown whereby the use of computers can be extended to more complex tasks. The regular calculation of grades and tonnages of material to be extracted from specified areas of an operating open pit is a necessary part of production planning. In this paper it is shown how these calculations can be carried out by computer. thereby freeing planning staff from manual calculation. An operating open-pit mine can be described in terms of drill logs, geological ore boundaries and pit perimeters at various levels. These form the data base which must be suitable for frequent updating to incorporate new information. A suite of computer programmes is described which operates on this data base to calculate tonnages and grades of ore within extensions to the perimeters as indicated to the system by planning staff. Possible future extensions are discussed.

Jan 1, 1971

Lightweight polymer grids have recently been introduced to the mining industry. They are currently being used for roof and rib control, longwall shield recovery, safety guarding or barricade, highwall screening, internal reinforcement of gunnite/shotcrete applications, sub-base reinforcement, construction of steepened slopes, retaining walls, mine reclamation (i.e. erosion control, turf reinforcement), and in numerous mining waste related projects. These polymer mining grids utilize a strong, lightweight polymer, usually special grades of polypropylene or polyethylene. High tensile strengths are achieved by molecular orientation of these polymers in the manufacturing process. The first step in the manufacturing process is to extrude the polymers into thick continuous sheets. These sheets are then punched, and drawn into open grid structures. Aperture size and configuration are controlled by the geometry of the punched hole and the degree to which the grids are stretched. The drawing process is the key to the molecular orientation required for the tensile strengths. These long chain polymer molecules in their natural state have a random orientation. When stretched, the molecules are pulled into a parallel alignment, thus creating a lightweight product with tensile strength comparable to Steel.

Jan 1, 1992

By Brimblecombe P

Morwell Open Cut is a continuous mining operation employing 5 buck- etwheel excavators, I bucket chain excavator and 54 conveyors. The combined bunkering capacity at both client Power Stations represents less than 12 hours maximum coal demand. This creates an extremely dynamic operating environment, which is further complicated with significant variations in both excavating and transportation plant capabilities. To achieve set objectives, including- I adequate reserves, 2 coal supply reliability, 3 cyclic plant maintenance, 4 minimal cost of coal, scheduling of the operation requires constant monitoring and reappraisal. Investigations are in progress to develop a computer based scheduling tool capable of simulating the complex operating environment. A review of computer scheduling packages currently available within the State Electricity Commission of Victoria has found limitations making most unsuitable for the task. The type of package found to be most suited is a knowledge based system ('Expert System')capable of operating within a set of rules defined by the user. Work is proceeding on the development of a knowledge base to test the effectiveness of Personal Computer based `Expert Systems'.

Jan 1, 1989

By Isaac AK

The combination of shot-firing and stage loader, and a prop and bar support system is an accepted drivage method. The support configuration is based on the final prop density, and assumes relitively uniform load sharing between the props. During the development of a longwall faceline at a medium depth (approximately 600m) British coal mine using such a drivage method, a fall occured overnight, effectively closing approximately 40m of the drivage. The severity and speed of the fall prompted an investigation into the performance of the temporary support system installed prior to chock installation. This paper deals with the investigation which disclosed some major contributory factors towards loss of strata control.

Jan 1, 1986

The design of mine ventilation systems for the BHP Steel Division Collieries is based on the acquisition of ventilation survey data for the establishment of a realistic computer net- work model. The branches which form the net- work for the computer models are calculated from a range of resistance factors incorporat- ing both a frictional and shock loss component. Since shock losses can account for up to 30 per cent of the total energy losses in mine airways the use of friction factors alone without accounting for shock losses will result in the choosing of an insufficiently performing fan. Published tables of friction factors have in- variably been taken from metalliferous or single entry studies and consequently are not reliable for Australia's mining conditions where multiple entries with regularly spaced cut-throughs are the normal practice. Typical resistance factors for roadways of rectangular cross-section 5.5 m x 2.0 m, with coal sides, have been found to vary from 0.11 Ns2/m8/km where no timber supports are used, to 0.98 Ns2/m8/km where double centre legging together with wooden chocks is used. In addition to the range of resistance factors due to varying support methods, the nature of use for a roadway is very significant because of the condition of repair and upkeep maintained.

Jan 1, 1983

Geological information plays a significant, cost effective role, in the Mt Whaleback iron ore mining operations. The geology and structure are complex. Good communication between the Mine Planning Production Scheduling and Quality Control Sections is the key to utilisation of geological information to its full potential.Drilling and pit face mapping are the two basic sources of detailed data sets which are processed to prepare up to date geological cross sections and benchwise geological plans. This information is used directly for the blast pattern design and production scheduling. Physical ore type estimation is also undertaken. Orebody models are generated from the geological information.

Jan 1, 1990

By Savage E. N

Two genetic types of base metal deposits occur in the Wainivesi area of central eastern Viti Levu. The Wainivesi deposit is now considered to be a stratiform volcanogenic type, and the Wailotu and Wainiviti deposits are described as contact metasomatic with some hydrothermal manifestations. The Wainivesi mineralization is correlated with the Tertiary "e" stage, i.e. uppermost Oligocene-Iowermost Miocene. Tertiary "e" stage rocks in Fiji are therefore potential ore producers of stratiform volcanogenic type. On the basis of plate tectonics with Fiji part of the New Hebrides Arc prior to rifting apart in the late Miocene, stratiform volcanogenic deposits of the Wainivesi type may also occur in rocks of comparable type and age in the New Hebrides.

Jan 1, 1976

By Rigby D, Gould K. W, Hart G. H

The variation in chemical and isotopic composition of hydrocarbon gases generated from humic source rocks in the Cooper Basin, the orth West Shelf, the agoorin oil shale deposit. ollinsville and the southern Sydney Basin is reviewed, discussed and interpreted.The primary composition of gases generated in and released from such source rocks appears to be very largely controlled by the degree of dispersion of the organic material. For example in eoaly shales, where the degree of dispersion may be high, products as generated may escape into surrounding inorganic structures where further maturational reactions may proceed. On the other hand, when the organic materials occur in massive form, as in coal seams, the hydrocarbons generated tend to be retained within the coal. Further cracking to the stage of methane generation is usually required before release of hydrocarbon products is significant.Secondary factors of importance in determining seam gas composition in the Bowen (Collinsville) and southern Sydney Basins are the invasion of coal measures by carbon dioxide from external magmatic sources and/or the vertical diffusion and loss from the surface ofgases generated at depth.Isotopic measurements of gas composition have been particularly valuable in determining the origins and histories of the gases examined, in demonstrating when gases are of mixed origins and in the prediction of gas quality in exploration.

Jan 1, 1985

By Newell R

The situation in which a gas stream flows through a bed of solids is found in many extractive metallurgy operations. Examples include blast furnace smelting, sintering and pellet firing. In such cases the resistance of the bed to fluid flow and heat transfer is of major significance to the operation of the process. This depends on the structure of the bed, which in turn is influenced by the manner in which the materials are charged to the bed. In this work, packed beds of hematite pellets of two different sizes were prepared in which the pellets were charged as a uniform mixture and in layers. The porosity, flow resistance and heat front velocity were measured and compared for the different bed configurations. For layered beds, the overall porosity and heat front velocity increased while the flow resistance decreased when compared with the values obtained for the uniform mixture. The size of the layers also had an effect on flow Properties.

Jan 1, 1991

Environmental considerations were key factors in the design of the Ranger Uranium Mines treatment plant. The mine is located adjacent to the Kakadu National Park and has an average rainfall of 1.6m per annum. Initially, no contaminated water or liquid effluents are to be released from the project area and thus water management is a key design and operating fact. Particulate and gas emission criteria influenced design as did occupational hygiene factors (dust, radon, housekeeping, maintenance access). Equipment selection and engineering standards were conservative and resulted in the plant attaining design performance in less than three months from the date of commissioning. A number of mechanical and operational problems were experienced and are discussed in the paper, however none of these problems have had a significant effect on production.

Jan 1, 1984

This paper considers two particular empi- rical models for the processes of the generati- on of hydrochemical zoning and epithermal near- surface mineralization of mercury-antimony-arse- nic formation in the discharge area of the Uzon Caldera ore generating hydrothermal system in Kamchatka. Vertical and horizontal hydrochemical zo- ning is caused by mixture of infiltration waters of the surface formation with fluid of chloride- sodium composition which are supplied up the-zo- ne of deep fault. Ore formation is caused by simultaneous existence of two geochemical barriers, namely oxidizing and reductive. The first barrier is determined by the-level of ground waters. The second one forms under the clay-opal screen un- der the influence of two factors, namely the inflow of deep reduction sulphur compounds (which are transported together with arsenic, antimony and mercury) and the generation of hyd- rogen sulphide as a result of sulphur- and sul- phate reduction. X-ray-amorphous phase of orpi- ment composition and realgar phase are formed, respectively, on the oxidizing and reductive Barriers.

Jan 1, 1987

By Romanovsky N. P

The Pacific Mobile Belt (PMB) is characterized by old origin and complex evolution both in time and space. As the global structure, the PMB is a narrow tectonic region dividing two plan-etary hemispheres, viz. the Pacific and IndoAfro-Atlantic ones, the relative shifting of which defines the character of many geodynamic processes in this belt. The PMB features inhomogeneity of structure, special matter composition characteristics, sharply broken-out topography, and intensive fields. Generalized anomalies of the gravitational field closely correspond to the PMB boundaries defined by the real features, i.e. the andesite line and distribution areals of Mesozoic-Cenosoic granitoids. The belt boundary position is controlled also by seismic velocity anomalies at a depth of down to 200 km. The modern PMB deformation is defined by the left-hand equatorial shift and rotation of the Pacific Ocean counterclockwise. This rotation is non-uniform in time and of an oscillating character. The motive forces of the phenomenon are considered.

Jan 1, 1990

Two independent sets of observations from rifted con-tinental margins suggest a way to reach a quantitative under-standing of how the topography of rifted margins erodes. First, a prominent erosional escarpment, which demarcates an elevated, inland region of low relief from rugged, deeply-incised terrain on the seaward side, is the main feature of the geomorphology of many rifted continental margins. Second, apatite fission track ages from the southeast Australian and southwest Saudi Arabian margins scatter about constant Paleozoic ages over the higher elevations inland from the escarpment, but decrease systematically seaward of the escarpment to near-rifting ages approaching the coastlines. We have developed erosion models based on conservation of mass principles to explain these observations. These models seek to explain the "rejuvenation" of erosion at the time of rifting, initiation of the observed erosional escarpment, and its migration inland with time at a rate on the order of 1 km/10 yr. We find from the modeling that erosion at rift flanks and passive margins is fundamentally a non-linear pro-cess. The erosional development of passive margin topogra-phy has much is common with travelling wave solutions to non-linear diffusion-type problems, and to self-similar sto-chastic processes, such as diffusion-limited aggregation. We suggest that the fission track data record the thermal effects of erosional unroofing at rift flanks and passive continental margins. Models intended to explain the erosional develop-ment of continental margins must explain both the geomor-phology and the fission track observations as well.

Jan 1, 1990

By T Baumgartl, B Richards

Covers on waste rock and tailings remain the primary choice for closure planning where the purpose is to create an environment where water ingress into reactive material can be controlled and/or prevented. In semi-arid and arid environments, dry cover systems are the preferred option with the design intention to absorb rainfall and to prevent deep drainage. Although the average amount of rain typical for semi-arid environments is relatively low and evaporative demand is high, the seasonal and annual distribution may vary greatly. Rocky substrates are often the only choice for the construction of covers due to economic constraints or availability of suitable materials. While the water holding capacity may be suitable for the application of a dry cover design in arid and semi-arid climates, some of these covers bear the risk of preferential water flow when rain events are intensive or occurring at high frequency. The objective of this presentation is to demonstrate the occurrence of preferential flow through rock containing dry cover systems. A regional classification for the applicability of dry covers is attempted to delineate those regions of Australia where the characteristic of the rainfall pattern increases the risk of failure for dry cover designs. CITATION:Baumgartl, T and Richards, B, 2016. Rainfall patterns rather than climate classification control cover design for closure, in Proceedings Life-of-Mine 2016 Conference, pp 89–92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

The basic methods to remove material from underground mines are to: convey continuously, batch in trucks, or batch in a shaft hoisting system. A critical aspect in shaft hoisting is accurately batch loading the conveyance or skip. During the 20th century, the almost universally accepted method of loading was via a measuring flask. A measured quantity of material was filled into the flask as the conveyance traveled through the shaft and then, when the conveyance arrived at the loading position, it was ædumpedÆ into the skip for hoisting. Two skip loading conveyor systems have been developed in Australia: BHP BillitonÆs Cannington Hoisting System, installed in 1996, is believed to be the first conveyor loading system designed for two skips. Two parallel conveyors were installed with a two-way gate controlling feed onto each belt. Cannington was ideally suited to conveyor loading as the very high ore density and relatively low production rate required a relatively small volumetric storage capacity on the weighed belt. Newcrest MiningÆs Telfer Hoisting System, which is to be commissioned in 2005, consists of a single slewing conveyor loading each skip with 32 tonnes of ore. The development of this system eliminates the two-way transfer, improves the accessibility and minimises the excavation required. While every hoisting system must be considered on its merits, conveyor loading offers significant advantages to the Mining Industry in the 21st century.

Jan 1, 2005

By Slater R

The initial planning and detail design phase leading to the development of a 7.5 m internal shaft to service the deep 3000 and 3500 copper orebodies at Mount Isa, Queensland is well advanced. The choice of internal shaft access was made over alternative methods such as a decline from existing levels and borehole hoisting. The resulting access development requirements and shaft configuration for production have been determined. Several techniques are being studied for shaft development. These include the application of blind shaft drilling and large hole reaming methods as well as conventional sinking techniques. As the 3000/3500 Orebodies extend from 1000 metres to more than 1800 metres below the surface, high stress conditions and ground temperatures ranging from 45CC to 62CC are anticipated. The effect of these on the methods being investigated to create a favourable working environment will influence the final choice. Exploration diamond drilling is in progress to confirm the geology of the orebodies so that planning for their extraction including refrigerated ventilation concepts can proceed.

Jan 1, 1982