Search Documents

By J. Marshall Rounsevell

It is probably not too far from the truth to say that the sulfur content of the steel bath at the first turndown of the basic oxygen furnace is influenced by every factor which varies in the operation of a BOF shop. However, the determination from normal shop operating data of the effect of a given factor on turndown sulfur content requires a means for collecting a large quantity of such data and a significant variation of the factor in question in that data. In this paper, operating data from 4000 heats collected on the computer at Inland's No. 4 BOF Shop is utilized to analyze the effect of four operating parameters -- hot metal sulfur content, hot metal manganese content, percent burnt dolomitic lime (dolomite) in the flux charge, and the presence or absence of transfer ladle slag skimming -- on first turndown sulfur content.

Jan 1, 1972

By C. J. P. Ball

Prior to 1939 the bulk of the magnesium metal produced outside of the united Stater was extracted directly from the ore and ifi the United States from magnesium chloride obtained as a by-product from the treatment of natural brines. A typical brine is one containing about 0.25 to 0.75 per cent bromine, 11 to 14 per cent sodium chloride, 9 to 11 per cent calcium chloride and 3 to 10 per cent magnesium chloride. The state of Nevada was known to possess large deposits of magnesite ore (MgCOs, the carbonate of magnesium), in Gabbs Valley, near Luning, approximately 350 miles north of Boulder Dam. Deposits mined in Europe were supplying magnesite giving 97 per cent MgCOs with about I per cent each of silica, lime and oxides of iron and aluminum. parts of the Luning de-posits Were almost equally rich, and the general average was of sufficiently high grade for production of magnesium. power to the amount of 200,000 kw. was available immediately from Boulder Dam, and water from Lake Mead, and it was this combination of available power, water, and ore that led to the initial proposal to erect a magnesium reduction plant in southern Nevada to reduce the magnesite ores from Gabbs. The extraction of magnesium metal from these magnesite deposits had been considered by the I. G. Farbenindustrie of Germany as far back as 1929. Mine and Oxide Plant The mine and oxide plant of Basic Magnesium Incorporated are perched upon the oride slope of the Paradise Range, at an altitude of 5000 ft., overlooking the 30 mile desert panorama of Gabbs Valley, Nevada. , Ore Occurrence The Gabbs magnesite ores occur in a thick series of flat, westerly dipping dolomites of Upper Triassic age. The mag-"esite bodies are exposed in steep canyon "areas encircling the north and east edges of a northerly projecting tongue of a roughly elliptical stock of granodiorite, which intrudes the dolomite. The magnesite mineralization is considered to be a a of calcium by magnesium through the agency of hydro-thermal solutions associated with the intrusion of the granodiorite. The ore bodies are of very irregular shape and distribution. Incomplete evidence points to deep pipelike replacement shapes that mushroom out erratically at various elevations. A wide latitude in the degree of magnesium replacement is reflected in a variance of quality from pure magnesite to magnesitic dolomite. The, ore is a massive crystalline mag-nesite. Though some differences in characteristics occur between ore bodies, in general the ore is a medium-grained carbonate varying in color from white, through all shades of gray, to black. Recrystallized dolomite, which encloses and occurs as

Jan 1, 1944

By A. Kenneth Schellinger, O. Cutler Shepard

Overgrinding, Or the breaking of ore particles into sizes smaller than required for liberation, is a first-magnitude problem in grinding for concentration processes. The conventional ball mill-classifier circuit used in commercial grinding produces mineral particles that are all ground to pass an upper size limit, while the proportion of very fine sizes, or slimes, is uncon rolled. Calculations based on measurements made in commercial plants which were grinding ore for flotation concentration indicate that about go pct of the energy used in grinding is consumed in useless overgrinding.1 In addition to accounting for the consumption of a large amount of energy, over-grinding is detrimental to the flotation process. Overground slime coats larger partitles and inhibits selective action by the flotation reagents on particles which by themselves could be separated very well. A further difficulty is that extremely finely ground minerals do not respond satisfactorily to flotation-collecting reagents, and both selection and recovery decrease markedly with particles finer than 5 to 10 microns.2 conventional classifier-ball mill circuits inherently tend to overgrind the valuable minerals more than the gangue minerals because most valuable minerals are of higher density and are softer and more friable than the gangue minerals. The rem- edy to this situation would seem to be a separating mechanism which would separate free valuable mineral particles regardless of size and density considerations and a mechanism which would operate in the grinding mill so that valuable mineral grains would be removed from the grinding machine as soon as they are freed. A consideration of these ideas led the authors to the conception of a simultaneous grinding and flotation mechanism. So far as the authors are aware, such a machine has never been tried, even on a laboratory scale. Development oF Apparatus and Experimental Method Apparatus development went through several stages before a really workable machine was devised. Work was started with a large cast-iron mortar 7½ in. in diameter and 8 in- deep. A cast-iron disk Was mounted on the end of a vertical shaft SO that it fitted loosely into the bottom of the mortar. On top of the disk four radial cleats ¼ in. high were bolted to agitate the ball charge as the disk, or impeller, rotated. The vertical shaft was driven at 100 rpm by a mechanism improvised from an old coffee-mill type of grinder. A hole was drilled into the bottom of the mortar through which compressed air was introduced for frothing. In operation, more charges of Ore which had been crushed to pass an 8-mesh screen were placed in the bowl along with water and suitable reagents. The impeller was then started and the compressed air turned On so that the ore was ground while being exposed to air bubbles. Mineralized froth was

Jan 1, 1949

By R. Silverman, H. Blumenthal

It was found that despite the similarity of chemical analyses of different titanium carbides used as base materials for cermets, the physical properties, especially transverse-rupture strengths, of test bars were different. Hence this metallographic study attempts to link physical properties to micro-structures. It is shown that microstructure, grain shape, and grain growth are functions of three interrelated factors: 1—powder production procedure, 2—surface conditioning of the particles, and 3—impurities either contained in the original powder or acquired during ball milling. An explanation is offered for the "coring effect," long observed, but heretofore of unknown origin. The explanation is based on assumption of an oxide film and on chemical analyses which substantiate these findings. TITANIUM carbide has become in recent years a material of great interest in the high temperature field. Consequently, many manufacturers in the United States and Europe are producing titanium carbide for cermet applications as well as for additions to the well known tungsten carbide tools. All present commercial processes of titanium carbide production utilize the chemical reaction of titanium dioxide and carbon to form as nearly as possible stoichiometric Tic. This reaction is carried out in three ways: 1—in a menstruum of molten metal,' 2—in the solid state, either in a protective atmosphere2 or in vacuum;" or 3—in an are-melting operation. In spite of the fact that the pure carbides obtained in these operations are almost identical chemically, the physical properties vary considerably when they are combined with a binder (Ni, Co) to form cermets. This fact led the authors to examine metal-lographically nickel-bonded titanium carbide in order to find the possible reasons for this behavior. Materials and Methods Five different titanium carbides were used in this investigation. They are identified in Table I. The first four materials were used in the as-received condition. Material E, received in lumps, was crushed to —100 mesh and carried through a flotation process in order to bring its graphite content in line with the other products. A Galagher flotation cell was used with pine oil as frothing agent. The chemical analyses of the investigated materials are given in Table 11. The binder used was carbonyl nickel of 9 to 14 microns particle size, supplied by A. D. Mackay. The materials were ball milled at a ball to charge ratio of 6:1 using procedures described under "Experiments and Results." All particle sizes mentioned are averages determined with a Fisher Sub-sieve Sizer. Test bars (lx0.40x0.16 in.) were prepared by 1—hot pressing to 85 to 95 pct of theoretical density at pressures between 1 and 1½ tsi and temperatures from 1600" to 1800°C, 2-—-cold presssing after 3 pct camphor had been added, or 3—wet pressing, both 2 and 3 at pressures between 5 and 10 tsi. All pressed bars were sintered in a vacuum of 105 to 10-6 mm Hg for 2 hr at 1350 °C. Transverse-rupture strengths were determined by breaking on a Baldwin Universal Testing Machine over a 9/16 in. span. Densities were measured by water displacement. The preparation of the specimens for micrographs was done according to Silverman and Doshna Luscz." All magnifications are at X1000. A sodium picrate electrolytic etch was used. Experiments and Results The influence of ball-milling procedure, ball-milling medium, pressing procedure, and sintering procedure on the microstructure of 80/20 — TiC/Ni were investigated. Ball Milling of Materials A, B, and C in a Steel Mill: Figs. 1 and 2 show microstructures of hot-pressed and vacuum-sintered test bars of materials A and B after the respective materials had been ball milled to 2.1 microns particle size in a steel mill and mixed with 20 pct Ni binder. Material A (Fig. 1) shows considerable grain growth. Also evident is a tendency of the carbide grains to coalesce. The density is 98 pct and the low transverse-rupture strength of 111,000 psi is probably caused by many large grains and an unfavorable packing factor. Almost all grains show a slight indication of "coring." Material B (Fig. 2), although showing grain growth, still has many small particles and a better distribution of binder and carbide due to the relative absence of the coalescing tendency. "Coring" can be observed in almost all grains. The high transverse-rupture strength of 179,000 psi and the density of 100 pct are believed to be due to the many small grains completely surrounded by the binder phase. There is also a preference to form spherical grains with material A, while most grains of material B preserve their angular shapes. Material C, of which no picture is given, stays between A and B in every respect. Rounding of some grains can be observed as well as coring, but the latter to a lesser degree than with material B. Its densification is good and the transverse-rupture strength obtained is 142,000 psi. Ball Milling of Materials A, B, C, and E in a WC Mill: When the Tic powders were ball milled to 2 microns particle size in a we mill, then ball-mill mixed with 20 pct Ni binder, hot pressed, and vacuum

Jan 1, 1956

By G. A. Moore

A brief review is given of methods designed to produce metallic iron of high purity, and typical results are listed. A recent method, utilized at the National Bureau of Standards, consists of the extraction of ferric chloride by ether, reduction of this ferric chloride to ferrous chloride, further purification of this chloride, and the subsequent electrolytic deposition of metallic iron. iron produced by this procedure apparently is softer than, and otherwise different in properties from, any iron previously prepared and contains appreciably smaller amounts of impurities. THE history of attempts to produce "pure" iron reaches to antiquity and it may be presumed that each ancient armorer who succeeded in making a better steel concluded, correctly, that he had done a better job of removing the "base metals," and incorrectly, that he now at last had a "pure" metal. Early metallurgical papers mentioned use of "pure iron" in making alloys—this "pure" iron in most cases being inferior to some commercial stocks of the present time. Improvement has been continuous, and usually at a sufficient rate to convince each succeeding group of workers that they, at last, were using the really pure metal (until the analysts also improved their techniques to again discover the impurities). These adventures were reviewed in some detail by Cleaves and Thompson.' Although the ores of a metal may be abundant, difficulties in extracting it may make the pure metal very rare. When impurities are restricted to a total of a few parts per million, nearly all pure metals become rarities. Lead, copper, gold, mercury, silver, zinc, aluminum, bismuth, and the six platinum metals are claimed to be available with total impurities ranging from 2 to 50 ppm. The present small and scattered world supply of so-called "pure" iron holds an unimpressive place in another group of 16 metals having approximately 100 ppm of foreign material. Of about 20 less rare metals, only the platinum metals are more costly to prepare. While the production of such rare varieties of iron may appear insignificant in the presence of thousand-ton operations with 95 to 99 pct metal, it must be emphasized that all researches on commercially interesting irons and steels are in fact studies of the modifications of the properties of iron by additional materials. Until the properties of high purity iron are directly measured, all ferrous research must operate without known base values. Traces of impurities may affect the properties of a metal in many ways. Infinitesimal traces of solutes, by disturbing the electronic configuration, greatly change the electrical properties of transistors and semiconductors2-3 and slightly larger traces might alter these quantities in iron. Soluble impurities which disturb the perfection of lattice arrangement not only may alter the magnetic constants and electric properties, but by their close association with dislocation phenomena probably control the very existence of the "yield point"; determine the value of yield stress; and perhaps control the selection of slip and cleavage planes. It has been speculated that impurities might even cause the allotropic transformation in iron, but in any case their rearrangement must contribute to the unreliability of heat capacity and other thermodynamic measurements. Impurities which do not remain in solution may cause even greater effects on the properties. Microscopically visible amounts of phases other than ferrite can be found in all high purity irons which have come to my attention. It can be calculated that from 50 to as little as 2 ppm of an insoluble material might be sufficient to completely film all grain boundaries in irons having grain sizes from ASTM Nos. 10 to 1. Should this occur, such films, even though invisible, may be very important in fracture problems, especially at extremes of temperature:' Studies of grain growth and diffusion normally imply consideration of a single-phase system, hence, in the presence of insoluble impurities they can be expected to give ambiguous data." High purity iron is also in demand for use as chemical and spectro-chemical standards; for work in classifying the lines of the iron spectrum; for biological work in nutrition; and for work in nuclear physics. where the presence of some sensitive

Jan 1, 1954

By Herbert M. Wilson

We of the employer class represent labor in the social organization and in industry just as truly as do those who labor only with their hands, and, because our labor is chiefly with our brains, the duty is all the more imposed upon us to use those gifts in which we excel in helping steer a clear course through the turbulent waters in which we are now enmeshed. Only their selfish engrossment in the daily tasks they were employed to perform could possibly have permitted the great majority of the intelligent and industrious German people to become terrorized by a handful of the idle, the vicious, and the criminal, whom the elections to the National Assembly showed to be in as pitiful a minority as they are in Russia, in this, and in other countries. It is the leisure unemployment of the I.W.W.'s, the Bolsheviki, and the Sparticans that has enabled them to devote their whole time to a concerted and aggressive struggle against the great majority of those of the world's workers who are unorganized, and who are therefore even in opposition one to the other. In union there is strength, and this was never better illustrated than by these conditions. The great fallacy of our previous attitude toward social and industrial problems has been the belief that labor, by which we commonly mean organized or physical labor, is something antagonistic to and having a different object in life from that great body of unorganized laborers who work with their brains. Our difficulty has been our lack of will or opportunity to think. The hurry of our daily struggle to earn our livelihood under the nerve-racking pressure of modern civilization has left us no opportunity for quiet thought and study. The physical laborer, and above all the laborer in the mines, on the other hand, has all his hours of toil in which to think over, in all their varied aspects, those problems that concern his immediate, personal well-being. As a result he has arrived at perhaps a more true appreciation of the facts of life in their relation to social and industrial conditions than we. Have we not too readily adopted the view that, as the managers of industry under the direction of capital, it has been our duty to think and act in opposition to labor, rather than to realize that we also are laborers, have like aspirations, and should participate in a free and aggressive solution of these problems rather than leave their solution

Jan 1, 1919

By Arthur R. Kommel, Robert F. Mehl, Gerhard Derge

The orientation relationships resulting from allotropic transformations and the formation of segregate structures in metals and alloys have been the subject of the eight earlier papers in this series'. A brief summary of orientation studies has also been given by Sachs2. A survey of these papers discloses that the factors that determine the orientation relationship of a precipitated phase to its parent solid solution, as well as the outward form and appearance of the new phase, are not completely understood. It is now evident that crystallographically analogous systems, as a rule, exhibit the same type of Widmanstatten figure and orientation relations, so that useful information is not to be expected from examination of a new alloy involving lattice combinations of which the orientation relationships are already known. Therefore, the determination of the relations existing between lattice types that have not already been studied seems to be the most promising mode of attack upon the problem; both of the systems reported in this paper represent new combinations of lattice types. A. The Mg-Mg2Sn System The magnesium-tin equilibrium diagram given by Hansen3 shows the phase Mg2Sn to be the only intermediate phase. The solid solubility of Sn in Mg decreases from 14.8 weight per cent at the eutectic temperature, 561' C., to 2.3 per cent at 450°, while no solid solubility of Mg in Mg2Sn has been observed. The crystal structur: of Mg is close-packed hexagonal with a0 = 3.202 A. and co = 5.199 A.4, while Mg2Sn is of the CaF2 type with a. = 6.78 A., with four molecules in a unit ce115,6. Alloys from two different sources have been used: (1) those supplied by the Dow Chemical Co., which contain 6 and 8 weight per cent Sn, and (2) those prepared in this laboratory, containing 8 and 13.5 per cent Sn. The latter were made from Dow high-purity Mg and Baker chemically

Jan 1, 1937

By Albert Sauveur

Some writers believe that when austenite transforms completely into pearlite on slow cooling through the thermal critical range, such transformation does not imply the formation of any of the so-called transition constituents: martensite, troostite and sorbite. Might it not be claimed with as much justification that when water freezes it does so suddenly, solid ice being obtained without passing through the intermediate stages of ice and water? Obviously, regardless of the speed of solidification, this would be erroneous. Before reaching the completed solid condition, this must of necessity pass through an unbroken series of stages when the system consists of mixtures of water and of ice, the former decreasing and the latter increasing in amount. Are not these "transitionV stages in the freezing of water similar to the transition stages occurring in the transformation of austenite into pearlite? To clarify, let us consider in Fig. 1 the mechanism of the transformation of eutectoid steel from its austenitic to its pearlitic condition as it cools slowly through its thermal critical range. It is generally admitted that this transformation is the result of two distinct phenomena: (1) the allotropic change of gamma iron into alpha iron and (2) the crystallizing out of solution of the carbide Fe3C. Whether this crystallizing of Fe3C implies also its formation is immaterial for our purpose. In other words, whether it is the carbon in atomic dispersion which is present in gamma iron or molecules of Fe3C has no bearing upon the matter to be discussed. The transformation of gamma iron into alpha iron cannot take place suddenly. It must of necessity be progressive, regardless of the speed with which it may take place. At A, for instance, there would be present AB gamma iron and BC alpha iron. The distance MN does not refer to falling temperature, but to the passage of time. It may be assumed that the transformation takes place at a constant temperature (the Ar321 point). In a similar way, the crystallization of Fe3C out of the austenite solid solution must be progressive as depicted between M and N. At A there would be present AB gamma iron, BC alpha iron, CD carbon dissolved in gamma and in alpha iron and DE Fe3C. This condition may be described according to individual preference as martensite or troostite. To sum up, can the metal pass from condition

Jan 1, 1931

By H. S. Chiang, D. F. Lu, S. S. Peng

INTRODUCTION The most important element in a successful lingual mining is a good roof control. The modern longwall mining employs hydraulic powered supports for roof control at the face area. The application of hydrau¬lic powered support requires the knowledge of over¬burden strata behavior for proper selection of sup¬port type and capacity. Failure to do so could lead so serious loss. There are several methods available for determining the required support capacity (1-3). While these methods are simple for application, they do not include the complicated roof behavior observed in longwall mining. As research progresses and operational experience accumulates (4,5), the concept about the designing and selection of powered support improves. The design of a longwall powered support consists of three major phases: 1. structural integrity and stability of the powered support, 2. external loadings induced by the movements of the overburden strata, and 3. interaction between the support, roof and floor. Phase 1 involves structural analysis (5) and full-sized testing (6) of the supports. Its validity is limited by the accuracy of the assumed external loading because of the uncertainty about the actual loading underground. The third phase includes the reaction of the support and the floor to the movements of the overburden strata and vice versa. Among the three phases, the second phase concer¬ning the external loading seems to be the least known because of the complicated behavior of the roof strata. There are many unresolved problems. For example, does the main roof break periodically and cause periodic roof weighting in the face area? If so, are there any rules governing its behavior? How does the roof load on the support canopy! Finally, how can one determine the required support capacity and select a proper type of support to meet a certain roof behavior? In order to answer those questions, underground instrumentation and observations were performed at 4 longwall panels in 3 separate mines for the past two years. This paper summarizes the current findings. PANEL LAYOUTS AND EQUIPMENT EMPLOYED The three mines selected are all located in West Virginia; two in northern and one in southern West Virginia. As shown in Table 1, seam conditions (i.e. seam, depth and thickness) and panel layouts are different among the three mines. The most significant difference in equipment is the face powered supports. Three mines used three different types of shield; 2-leg caliper, 2-leg lemniscate, and 4-leg lemniscate chock-shield. (Fig. 1) UNDERGROUND INSTRUMENTATION AND OBSERVATION PROGRAM Two events were instrumented in each observed longwall face: one was the hydraulic pressure (resistance) of the powered supports and the other was the canopy load distributions. In addition, the gob caving conditions were visually observed and recorded. Leg and Support Resistances One or two automatic Weksler Pressure Recorders were installed at the designated shield support,. In most cases, the daily charts were used to record the pressure variations in both the front or the rear legs (for the 4-leg shield), or in both the leg and the fore-pole ram (for the 2-leg shield). The recorded pressure w a s then converted to load or resistance by multiplying it by the cross-sectional area of the hydraulic leg or canopy ram piston. Fig. 2 shows the typical pressure-recorded charts for the 4-leg and 2-leg shields in a 23-24 hour period. The support resistance is the summation of the resistance in each of all the legs for that support. Generally, the resistance of the fore-pole ram will not be considered in determining the capacity of the support because of its rather small vertical compo¬nent force at the tip of the fore-pole. Canopy Load Distribution External load distribution on the canopy as exer¬ted by the roof was monitored. The measurements employed 12-14 pieces of pressure cells (6-inch square) that were uniformly arranged in two rows on the canopy. After support setting, the pressure changes in the cells were monitored at various stages of the mining (supporting) cycle while the support leg pressures were recorded continuously by the pressure recorders. Based on the calibration chara¬cteristics of each pressure cell as performed in the laboratory before and after each underground test, the cell pressures were converted to actual loadings. From these load measurements the canopy load distri¬butions and the relations between measured canopy loadings and support leg resistances were determined. Accordingly, the supporting efficiency of the shield support can be determined.

Jan 1, 1982

By D. V. Edmonds, C. J. Beevers

Tensile tests were carried out on a! titanium containing 850, 1250, and 2700 ppm 0, and up to -500 ppm H. The tests were performed at -196", -78", 20°, 150°, and 300°C at a strain rate of -1.0 x 10??3 sec-1. Increasing oxygen content, increasing grain size, and decreasing test temperature resulted in enhanced embrittlement of the a titanium by the hydrogen additions. Metallographic observations showed that this can be correlated with the influence of these parameters on the introduction of cracks into the a! titanium by fracture of titanium hydride precipitates. CRAIGHEAD et al.1 reported that the hydrogen content normally found in commercial-purity a! titanium (60 to 100 ppm) was sufficient to cause a substantial lowering of the impact strength, and they attributed this embrittling effect of hydrogen to the precipitation of titanium hydride. Lenning et al.&apos; found that in commercial-purity a titanium there is an almost complete loss of impact strength at about 200 pprn H, which is approximately half the value needed to eliminate the impact strength of high-purity a titanium. They also showed that the presence of 3000 ppm hydrogen reduces the room-temperature tensile ductility of commercial-purity material to a value of the order of 10 pct; the corresponding hydrogen concentration for high-purity titanium is over 9000 ppm. It thus appears that the detrimental effect of hydrogen on the mechanical properties of commercial-purity titanium becomes evident at much lower hydrogen contents than for high-purity titanium. The main difference between the two types of a titanium might be expected to be the higher level of interstitial impurity in the commercial-purity grade. Jaffee et a1.3 studied the influence of temperature and strain rate on the hydrogen embrittlement of high-purity and commercial-purity ! titanium. In general, the behavior was the same for both materials; embrittlement was enhanced by decreasing temperature and increasing strain rate. Recent results from tests on commercial-purity a titanium containing 850 ppm O and varying amounts of hydrogen up to -500 ppm showed that the degree of embrittlement by hydrogen is intimately related to the fracture characteristics of titanium hydride precipitates.4 The present paper considers the interrelationship between the mechanical properties and micro-structural features of commercial-purity a! titanium containing 850, 1250, and 2700 ppm 0 and varying amounts of hydrogen up to -500 ppm. 1. EXPERIMENTAL PROCEDURE Three types of commercial-purity titanium supplied by IMI* were used in the investigation, and for the *Address: Witton, Birmingham 6, United Kingdom. purpose of this paper are designated Ti 115, Ti 130, and Ti 160. The principal impurity elements are given in Table I. The material was received in the form of 12.7 mm diam bars having a fully recrystallized structure. Tensile specimens with a round cross-section of 4.5 mm diam and a gage length of 15.2 mm were machined from the bars. In order to develop the same grain size (mean linear intercept of grain boundaries) in each of the three types the specimens were annealed under a dynamic vacuum of <10?5 mm Hg, Table 11. Specimen hydriding was carried out in a modified Sieverts apparatus;&apos; hydrogen was taken into solution at 450°C and after holding the specimens at this temperature for 24 hr they were furnace-cooled to room temperature at an average rate of -100 C deg per hr. By this method nominal hydrogen contents of 0, 50, 100, 250, and 500 ppm were introduced into specimens of Ti 115, Ti 130, and Ti 160 (100 ppm (wt) -0.5 at. pct). The actual hydrogen contents were calculated from the weight differences obtained by weighing the specimens before and after the hydriding treatment. Tensile tests were carried out at temperatures of -196", -78", 20°, 150°, and 300°C on a 10,000 kg In-stron machine at a nominal strain rate of -1.0 x 10-3 sec-1. Fractured specimens were sectioned in planes parallel to the tensile axis, mechanically polished to 0.25 µm grade of diamond paste, and then attack polished using a solution containing by volume 99 parts H2O, 1 part HF, and 1 part HNO3. Although the latter treatment unavoidably opened out cracks and voids visible after mechanical polishing, it did reveal the grain structure, titanium hydride morphology, and deformation twinning structure.

Jan 1, 1970

By R. S. Busk, E. G. Bobalek

THE relation between gases and metals has been a subject of increasingly active investigation during the past years, principally devoted to the study of metal-hydrogen systems. It has been found that hydrogen is soluble in most molten metals to an appreciable extent and somewhat soluble in most solid metals.1,2 In every known case there is a sudden decrease in solubility at the melting point. Thus a freezing mass of metal containing hydrogen in excess of the solid solubility must in some way expel that excess during the freezing process. This leads to internal blowholes, and such effects as pinhole porosity. Gas trapped in metal that is to be fabricated by a working process such as extrusion or rolling may be the cause of blisters. For some cases, notably in copper and iron alloys, the presence of hydrogen can lead to extreme embrittlement of the metal. The aluminum-casting industry has long recognized the importance of hydrogen in its techniques. Excess gas in molten aluminum alloys often leads to the formation of "pinhole porosity" in the solid casting.3 To prevent this hydrogen pickup it is necessary to avoid overheating the melt and to protect it from such sources of hydrogen as water. In spite of all precautions, it is sometimes necessary to extract hydrogen from the melt just before pouring by bubbling with a gas such as chlorine or nitrogen. Recently it has been found that somewhat similar effects are possible with magnesium alloys, in that the presence of hydrogen can induce or aggravate microporosity.4-6 This paper is primarily concerned with a presentation of some facts concerning the solubility of hydrogen in magnesium and its alloys, with some discussion of the significance of these facts in a practical sense. In any study of gas-metal systems it is important to bear in mind a clear distinction between adsorption on surfaces and absorption within the lattice.1 Considerable attention has been directed toward determining whether hydrogen is truly soluble in any solid metal, or whether the gas extracted from a sample was present at surfaces (external and internal) only.7 Most present day evidence supports the idea of true solution in addition to adsorption. A second important factor when dealing with gas solubility is the dependence of such solubility on external pressure. For diatomic gases such as H2, solubility in both liquid and solid metals apparently is proportional to the square root of the pressure, indicating a breakdown to a monatomic gas before diffusion into the lattice .2 For true equilibrium values of solubility, therefore, the pressure at the metal surface must be constant and, preferably, known. Very little has been published concerning the hydrogen-magnesium system. Winterhager has presented the most

Jan 1, 1946

By B. M. Larsen

IN spite of the great amount of operating experience and of studies directed toward elucidation of the interrelation of the several processes going on in the blast furnace, the present picture of its operation is based largely on indirect evidence and on speculation. The reason for this unsatisfactory situation is the extreme difficulty of making direct observations and significant measurements while the furnace is operating, and of translating laboratory experience to the conditions obtaining in the smelting process. Yet there are questions that can be investigated with some promise of a definitive answer; and it is the purpose of the present paper to set forth some of these questions, as a basis for discussion, which may, it is hoped, lead to active work on some of them. In order to provide a starting point for this discussion, some views held tentatively by the writer are outlined, along with a certain amount of evidence gathered from operating records and interpreted on the basis of the ideas expressed. These opinions may prove not to be pertinent, and may well not be in accord with the opinions of others; they have been included to encourage others to do likewise and on purpose to provoke informal discussion. In this way it should be possible to transcend the limitations of formal papers; to bring forth suggestions of new hypotheses or new methods of investigation; and to promote better understanding between investigators and operators in this difficult field. The statements made express the present views of one physical chemist who is not too familiar with all the difficulties of maintaining these enormous reaction vessels in reasonably smooth and economical operation; who, however, is persuaded that some of these difficulties would be less formidable if surer knowledge of the several interrelated and concurrent processes were available and made use of. For these difficulties arise largely, it is believed, from variation in conditions which the operator must meet as best be can, and should lessen as these conditions can be brought under control so that they are either made substantially constant or the variations are neutralized by compensating methods. A. VARIATION IN BURDEN AND IN MIXING OF CHARGE To the scientific investigator, who aims to control the conditions of experiment and to limit the number of variable factors, the most perplexing aspect of the blast-furnace process is that nothing seems to remain constant for long. Variations of burden seem to be unnecessarily frequent; and, even if the charge were constant from hour to hour, its constituents usually are not mixed as intimately as they might well be. It is understandable that separate layers of coke and of ore, also separate layers according to size, promote permeability and the

Jan 1, 1947

By G. R. Countryman, G. H. Thomas, I. Fatt

Miscible displacement in both thewetting and non-wetting phase has been studied in two-phase systems. Experimental data show that dispersion is a function of saturation and cannot be predicted from dispersion theory developed for single-phase miscible displacement. Some of the effect of saturation on dispersion is a result of the development of dead-end pores or a dendritic pore structure in multiphase systems. The presence of dead-end pores or dendritic structure is confirmed by pressure transient studies. INTRODUCTION Displacement by flooding with a miscible liquid is a possible means for recovering the estimated two-thirds of the oil that remains behind after primary production. The immense economic importance of a process that can recover such large quantities of oil has led to extensive laboratory studies of miscible displacement. As usual in production research, most laboratory studies of miscible displacement have not attemped to reproduce all of the conditions existing in a petroleum reservoir. In the early stages of investigation the need has been for information on the broad, basic principles of the phenomena involved in miscible displacement. The effects of overburden pressure, reservoir temperature, and wettability have been considered of secondary importance. However, one property of a petroleum reservoir which is expected to be of major importance and yet has been omitted from many laboratory studies is the presence of interstitial water. Two possible effects of interstitial water on the displacement mechanism in the hydrocarbon phase immediately come to mind. First, from the general1y accepted theory that capillarity governs the distribution of oil and water in porous rock one would expect that for water-wet rock the water will be in the small pores and oil in the large pores. A miscible displacement of oil carried out in the presence of water is operating in a pore size distribution shown in Fig. lb, whereas if the same test had been performed with only one phase present the pore size distribution is as shown in Fig. la. Although there is not yet a theory of miscible displacement which explains in detail the effect of pore size distribution, one would expect the differences between Figs. la and lb to influence the displacement efficiency. A second factor which may make a multiphase system different from a single-phase system is the presence in the multiphase system of dead-end pores or dendritic structure. Experiments of various kinds on reservoir rock have led to the belief that all pores in the network structure of a porous rock take part in conducting fluid during single phase fluid flow.1,2 There are then no dead-end pores and no fingers or dendritic structures containing stagnant fluid. In a multiphase system, however, the second phase may

By P. van Meurs

This paper describes a technique which permits visual observation of oil displacement processes througlrout the interior of a porous structure as thick as 2 in. A model having glass walls is filled with finely powdered glass. Such a model becomes completely transparent if the powdered glass pack is saturated with an oil having the same refractive index as the glass. When water or gar, with a refractive index different from that of the oil (glass) is injected, the model becomes opaque in the space occupied by the water (gar). visual observation and photography of these displacement processes are thus rendered possible. The following processes have been studied: (I) displacement of oil by water (linear drive) in a homo-geneous formation and in a stratified formation, (2) water flooding (five-spot well pattern), (3) solution gas-drive process, and (4) oil-bank formation. INTRODUCTION Most of the scaled model experiments heretofore carried out in the Koninklijke/Shell Laboratorium, Amsterdam, have been done in steel containers, in which oil-saturated sand packs represented the oil-bearing formation. In such experiments, for instance those on the displacement of oil by water, the cumulative oil production was measured as a function of the cumulative water injection. In order to interpret the measured production data, a need has for some time been felt for a means of observing visually what happens in the course of such experiments. Some information of this kind was obtained earlier by observing the water-oil distribution in various cross sections of the sand after the conclusion of the experiment.&apos; However, the technique used did not guarantee that the fluid distribution remained undisturbed. Moreover, the procedure was somewhat elaborate and the information obtained limited. Therefore a new technique has been developed, which is described below. DESCRIPTION OF EXPERIMENTAL TECHNIQUE AND APPARATUS Glass models simulating part of an oil reservoir are filled with ground Pyrex glass of a specific grain size, representing the porous structure of the prototype. Before an experiment is started, the porous formation has to be saturated completely with an oil having exactly the same refractive index as the Pyrex glass powder. All light-scattering surfaces of the glass grains become invisible and the formation is then transparent. If the oil is displaced by another fluid (e.g. by water in a water-drive experiment, or by gas liberated from the oil in a solution gas-drive experiment) the formation becomes opaque in the region where the oil is expelled from the rock.* The back of the apparatus is painted black and illumination is from the front; therefore, in the photographs of the experiments, the oil-bearing formation appears black, whereas the water- or gas-invaded areas are white.

Jan 1, 1958

By J. J. Gilman

Rates of prisnzatic plastic glide ( {1010}<2110>) in pure Cd crystals have been measured at temperatures from 158° to 276°C. The glide rate is proportional to the 2.75 power of the applied shear-stress. The activation energy is 29.2 kcal per mol. It is suggested that the rates of prismatic glide in Cd and Zn crystals are determined by the strengths of the atomic bonds across the prism planes. ALTHOUGH zinc and cadmium crystals both have hexagonal structures with nearly the same c/o ratios, their mechanical behaviors are quite different. Whereas zinc becomes quite brittle below room temperature, and cleaves readily on (0001) planes, cadmium is very ductile even at 4.2°K, and cannot be cleaved at any temperature. As part of a search for the explanation of this difference in behavior, a study has been made of prismatic glide in cadmium. It complements a previous study of the same phenomenon in zinc.1 The primary glide plane in cadmium is the basal (0001) plane, and the primary glide direction is the direction of atomic close-packing <2110>. However, if a tensile stress is applied parallel to the basal plane, then the shear stress on the basal plane equals zero so basal glide cannot occur. At low temperatures, deformation by twinning occurs; but at high temperatures, it has been found in this study that gliding on prismatic planes (1010) occurs in the close-packed direction. This is completely analogous with the case of zinc, except that lower temperatures are required. EXPERIMENTAL The experiments were done in nearly the same way as for zinc.&apos; Therefore, only the differences in the two sets of experiments will be described here; for other details the reader is referred to the previous paper. Crystals 6 by 6 mm sq were used that were grown from "Super Purity" 99.999 + pct Cd purchased from the New Jersey Zinc Co. The crystals were grown with their basal planes parallel to both the rod axis and one of the flat sides of the square cross section, A close-packed direction in the basal plane was oriented parallel to the rod axis. Gage sections were carefully machined into the crystals, and the surface damage caused by machining was removed with the same chemical polishing reagent as had been used for zinc. Thus, specimens of the same form and size as the previous zinc ones were produced. The crystals were heated to the test temperatures in a silicone oil bath (fused salts were tried first, but they reacted badly with the cadmium). An Instron tensile-testing machine was used for applying stresses to the crystals at various constant strain-rates. RESULTS The general behavior of cadmium crystals is much the same as for zinc. Only the constants that measure specific properties are different. Just as

Jan 1, 1962

THE composition and quality of finished steel depend upon selection and proportioning of the raw materials of the charge as well as upon control of furnace practice. This chapter deals only with the raw materials of the basic open-hearth process that are important in determining the composition of the steel or slay. They are the metallic charge, oxygen-bearing materials, fluxes, alloying and deoxidizing additions, and certain refractory materials used for maintenance of bottoms. Other refractories, which may affect the slag composition, are discussed in Chapter 3. Wide variations are possible in the type and composition of charged materials but certain limiting relations among the elements of the charge must be observed. Since the process consists essentially of refining by the oxidation of undesired elements, a balance must be established between the sources of oxygen and the elements in the charge that are subject to oxidation (see Chapters 2 and 7). For example, if it is desired to use a high ratio of blast-furnace hot metal to scrap, it is necessary to add an oxygen-bearing material such as ore or mill scale to eliminate the excess carbon and silicon that are present in the hot metal. An example of the opposite extreme is the use of a metallic charge composed entirely of steel scrap. With this type of charge, it is common practice to substitute burnt lime for limestone as a flux and to charge some carbonaceous material such as coke to avoid an excess of oxygen in relation to the elements of the charge that are subject to oxidation. Elements such as copper and nickel, which are not oxidized or eliminated by any other reaction, may be introduced into the charge only to the extent to which they are permissible in the finished steel. An example of adjustment of the charge for elements of this type is found in the use of steel scrap high in copper. In this case, metallic components of the charge other than the scrap should be low in copper, or a sufficiently high ratio, of pig iron to scrap should be charged to dilute the copper from the

Jan 1, 1964

By R. S. Archibald

THE Blueberry mine is about 10 miles west of Ishpeming, Marquette County, Michigan. The property consists of about 2000 acres in sets. 3, 4 and 5, T. 47, N.R. 28W. and sets. 32, 33 and 34, T. 48, N.R. 28W., and, excepting one intervening 80-acre tract, contains the iron formation for a length of about 2 1/4 miles. The property is traversed by State Highway M-28 and is served by three railways, the Chicago & Northwestern, the Duluth, South Shore & Atlantic, and the Lake Superior & Ishpeming. The Northwestern transports the ore to a dock at Escanaba; the other railways, to Mar¬quette. Ore for Chicago goes via Escanaba and that for Lower Lake ports, as Detroit, Cleveland, and Buffalo, via Marquette.

Jan 1, 1935

By Nelson B. Russell, Donald C. Bond

The effects of various antifreeze agents on the formation of hydrogen sulphide hydrate have been studied. On a molar basis the relative lowering of Tm (the maximum temperature at which solid hydrogen sulphide hydrate can exist in equilibrium with the given solution) for the various agents is: sodium chloride 1.00, calcium chloride 1.71, methyl alcohol 0.57, ethyl alcohol 0.68, ethylene glycol 0.73, diethylene glycol 0.73, sucrose 0.87, dextrose 0.71. On a weight basis the relative lowering of TM is: sodium chloride 1.00, calcium chloride 0.91, methyl alcohol 1.08, ethyl alcohol 0.89, ethylene glycol 0.69, diethylene glycol 0.41, dextrose 0.23, and sucrose 0.15. Introduction The solid hydrate of hydrogen sulphide, H2S.6H20,1 is in equilibrium with water and liquid hydrogen sulphide at 85°F at a partial pressure of hydrogen sulphide approximately equal to the vapor pressure Of hydrogen sulphide at that temperature. At temperatures below 85°F, in the presence Of excess hydrogen sulphide (greater than the amount required to react with the water present) the hydrate is in equilibrium with liquid hydrogen sulphide at approximately the vapor pressure Of hydrogen sulphide. In the presence of excess water, the solid hydrate is in equilibrium with liquid water, containing dissolved hydrogen sulphide, at a pressure lower than the vapor pressure of liquid hydrogen sulphide at the same temperat~re.2 The lower the temperature, the greater the difference between the decomposition pressure of the hydrate and the vapor pressure of liquid hydrogen sulphide at that temperature. Conditions conducive to the formation of solid hydrogen sulphide hydrate may exist in wells producing a gas containing a high percentage of hydrogen sulphide under high pressure, or in the lead lines from such wells. This paper gives the results of tests made with various antifreeze agents which might be useful in decomposing the hydrate or in preventing the formation of the hydrate of hydrogen sulphide Apparatus Fig , shows a diagram of the apparatus used. The sample under observation was contained in a glass tube 34 cm long, having a 6 mm id and a wall thickness of 2.5 mm. The lower end of this tube was closed- with a plug of butyl rubber. The upper end of the tube was connected to a diaphragm gauge, with a stainless steel diaphragm, a manometer, a vacuum pump, and a cylinder of hydrogen sulphide, The tube was held nearly horizontal, with the liquid resting along the lower side of the tube. It was found that when the tube was held in a vertical position, it broke with ex. plosive violence as soon as it became filled with solid hydrate. Presumably this was caused by the expansion which occurred on solidification of the hydrate. The difficulty disappeared when the tube was held in an inclined position during the tests.

Jan 1, 1949

By M. F. Comerford

M. F. Comerford (Smithsonian Astrophysical Observatovy)- The authors&apos; concern about the effects of preferred orientation is justified and emphasizes a phenomenon that can be a source of serious error, but the cogency of their concluding statement bears close examination. They contend that comparison of intensities from parallel planes of the two phases, as proposed by Averbach, Comerford, and Bever,13 leads to incorrect results. The state- ment is based on the fact that, in Fig. 3, intensity measurements at extreme angles of tilt, (2, lead to different values than those given by the average of all the data. The proposed explanation is that unsuspected superpositions of (110), reflections spuriously enhance the martensite intensity. However, it can be shown on appropriate stereographic projections that no superpositions occur which can affect the reflections in question. Hence, the ex-

Jan 1, 1965

By J. J. Pye, J. B. Drew

Mzasurements of the surface diffusion coefficients of metals have been made. Diffusion profiles for the Ag-Ag system were obtained by means of a radioactive point source and a precision auto-radiographic technique. The activation energy for silver self diffusion (=8.1 kcal per mole) is lower than that previously reported (-10 kcal per mole) on poly crystalline wire by Nickerson and Parker. The bresent data indicate an effect due to parasitic volume diffusion at temperatures above 500°C. RELATIVELY few measurements have been made of the surface self-diffusion coefficients of metals. Nickerson and arker&apos; measured the diffusion of silver over the surface of poly crystalline wires and estimated that the activation energy was 10.3 kcal per mole. Winegard and chalmers2 carried out measurements on both polycrystalline and single crystal surfaces but did not report a value of the activation energy. They found, however, that at temperatures between 250" and 400°C the diffusion coefficients were on the order of lo-&apos; sq cm per sec and that there was an acceleration of the migration of silver on the polycrystalline sample when a change of surface shape occurred. Winegard and Chalmers used an autoradiographic technique, hereafter designated ARG, and Nickerson and Parker used a surface scanning geiger counter in order to determine the diffusion profiles. More recently, Hackerman and simpson3 measured the surface self-diffusion coefficient of copper at a single temperature (750°C), and the value of the diffusivity (- 10-5 sq cm per sec) is in agreement with that given by jostein from his thermal grooving measurements. This paper reports the results of an investigation of the surface self-diffusion coefficients of silver over a large temperature range and describes the adaptation of autoradiographic (ARG) techniques for the determination of diffusion profiles obtained from a radioactive point source. EXPERIMENTAL PROCEDURE The experimental procedure is a modification of the method employed by Hackerman and simpson3 in their measurements on copper. A brief description of their technique is as follows: A radioactive needle which sinters to the surface during the diffusion an- neal serves as the source of diffusing atoms. After the diffusion run the needle is removed and the surface is scanned with a shielded counting arrangement. The diffusion profiles reported in this paper were obtained by a modification of the above procedure which employs a precision ARG technique. Previous investigations in this laboratory and elsewhere51B have shown that under carefully controlled developing conditions and by the use of calibration sources a linear relation exists between the concentration of the isotope and the photographic density for values below unity. The use of ARG under these conditions has advantages over the counter scanning method in that cumbersome shielding and requirements for great mechanical precision of the scanner are eliminated. Also the ARG gives a complete picture of the surface which is advantageous in studies of anisotropic diffusion. A recording microdensitometer having a 0.1 p wide slit was employed. At low temperatures the disturbing effects of subsurface radiations are negligible. The diffusion anneals are carried out in the cell shown in Fig. 1. The needle is formed by grinding down a 1.0 mm rod of high-purity silver until a tip of 0.2 mm radius or smaller is formed. This tip is plated withA"&apos; which becomes the source of the diffusing atoms that are detected by ARG. The needle carrier and the crystal holder, Fig. 1 are constructed of quartz and ports are provided in the holder pedestal which allow free vapor circulation ((2.0 oz) and the carrier apron fits snugly over the crystal holder cap, insuring that the needle does not move and scratch the surface. Temperatures are provided by a stabilized tubular furnace which can be quickly positioned around the cell, thus bringing the crystal up to temperature in a time that is short compared to the diffusing times. The diffusion anneals range from 2 hr for the high-temperature samples to about 25 hr for those at the lowest temperature. The possibility of vapor transport of the radioactive metal as a contributing factor in the diffusion profile was investigated in two ways. One method was to suspend the needle directly over a dummy sample, raise the temperature, for periods of time equal to the diffusion times, and then take an auto-radiograph of the surface. Negligible radioactivity appeared. In the second method a thin slot in the crystal face on one side of the source provided a "cong path" for surface diffusion. If evaporation was the primary source of surface atoms the region of radioactivity around the source would be symmetrical. This was not the case. The profile dipped abruptly at the edge of the slot but on the other side of the source the usual diffusion profile appeared.

Jan 1, 1963