Search Documents

By Raymond Mancha

The purpose of an accurate underground pressure survey is to obtain a pressure gradient along the circuit or circuits under investigation. The pressure gradient shows the rate of pressure drop between various observation points along a circuit. This determines excessive resistance regions and the economic feasibility of correcting such conditions by cleaning airways, driving additional airways, or modifying existing airways. A pressure gradient is useful for predicting the effect on other parts of the circuit when adjusting the air regulation on any one split or when planning a field airshaft or slope or a new drift to the outcrop. A single-compartment airshaft often produces disappointing results because it relievcs only a part of the circuit instead of the over-all mine pressure. It is valuable to know how the circuit pressure drop is distributed. The underground pressure survey is used also to determine the friction coefficient for various types of airway. High precision work is required to establish these vital data for predicting the characteristics of mine pressure volume when projecting new mine developments. Methods Regardless of the type of instrument used to conduct a circuit pressure survey, the work should preferably be performed at a time when the mine is idle, in order to avoid air-flow disturbances from moving trips and cages or from the opening or closing of trap doors. Preferably the survey should be made when the barometer is comparatively steady, to restrict variation in the air specific weight at observation stations while the circuit is traversed. The two most commonly used instruments for underground pressure surveys are: (I) the altimeter; (2) the inclined manometer with hose extensions. The altimeter is sufficiently accurate for determining the underground pressure gradient and is preferable to the nianometer for such work because of greater flexibility and shorter time required for the traverse. With the altimeter it is possible to select more widely separated observation stations than is practical with the manometer, with its restricted hose extension lengths. The altimeter also permits easier travel along haulage roads between airway observation stations, avoiding badly obstructed airways. The inclined manometer is more reliable than the altimeter for establishing friction coefficients in mine airways. Manometer readings are unaffected by differences in elevations between stations, which require corrections to altimeter data. The manometer provides direct reading without temperature correction, which may or may not be true with the altimeter, depending upon the make of instrument used. The elimination of correction factors combined with the instantaneous, simultaneous and

Jan 1, 1947

By Donald P. Bellum, Lee Nugent

Southwestern Utah is well known for its scenic attractions. The beauties of Bryce Canyon, Zion Canyon and the Grand Canyon are of world renown. Thusly, Cedar City is known, at least by the local Chamber of Commerce, as the Gateway to the Utah Parks. However, of the thousands of tourists flocking to Utah's many points of interest by way of Cedar City, few realize that any mining takes place in the vicinity, in spite of the fact that iron mines have been in continuous operation for 40 years. The Pinto-Iron Springs Mining District is only 15 miles west of Cedar City, and is the largest iron ore producing district in the West. In recent years, the shipments have ranged from 2% to 4 million tons per year making Utah the fifth-ranking state in iron ore production.

Jan 11, 1963

By J. T. Michalak, H. W. Paxton

The recovery of the initial flow stress of poly-crystalline iron is characterized by a) a logarithmic time dependence; b) an increasing activation energy with increasing recovery; c) an increased ?,ate and fraction of recovery with decreased temperature of deformation; and d) an increased rate with increased deformation. Isochro)ml studies of the recovery of single crystals revealed more sluggish recovery. The original flou3 stress of single crystals could be regained by recovery anneals at 800"or 900°C. ThE great majority of the theoretical treatments and experimental studies of strain-hardening have been concerned with the close-packed lattices.' Very little effort has been expended on the bcc structure so that the theory of work-hardening of this lattice is essentially nonexistent. The limited amount of experimental data resulting from the direct studies on silicon-iron,2 low-carbon steel,3 and purified irons4"7 does not as yet permit a detailed analysis of the strain-hardening. Studies concerned with the effects of annealing following deformation have been few in number," have been somewhat limited in extent, and have had the disadvantage of using irons containing a substantial impurity content. The present research was undertaken to augment the limited knowledge we have of the characteristics of a bcc metal as regards strain-hardening and recovery from the strain-hardened state. The recovery of the flow stress has been employed since it was felt that the stress associated with the hardened state gives at least a fair qualitative description of the state of the imperfections causing the hardening. The study was concerned primarily with the recovery of flow stress following strain-hardening of polycrys-talline, zone-melted iron as a function of the amount of deformation, the temperature of deformation, and the time and temperature of the recovery anneal. A limited investigation of the recovery of the initial flow stress of single crystals of this same material as a function of the recovery temperature was also conducted in conjunction with the Lambot X-ray technique." MATERIAL The zone-melted iron used in this investigation was obtained through the courtesy of the American Iron and Steel Institute and Battelle Memorial Institute. The analysis, as given by the supplier indicated a maximum impurity content of 0.02 wt pct excluding those impurities listed in Table I. (The actual impurity content is very probably less than this since detection limits were considered as the amount of a particular impurity level.) Also listed in Table I are the interstitial impurity contents of the iron at various stages of experimental work indicating that these im-

Jan 1, 1962

By Harvey P. Knudsen, Young C. Kim, Edward Mueller

Abstract-This paper describes the results of a comparative study of the geostatistical ore reserve estimation method over three conventional methods; the polygon method, the inverse of the distance squared (IDS) method, and ELIP which is similar to IDS. Each method was evaluated on its ability to accurately predict individual block grades for one bench of the Pima mine, located near Tucson, Ariz. Results at the Pima mine indicate that the geostatistical method is no better or worse in predicting block grades and total tonnage than the ELIP or IDS methods. In contrast, the polygon method is clearly inferior. All of the methods would have given better results if geology had been included in the block model. At already producing mines ELIP or IDS may be good choices since they involve substantially less cost in computer time. For prospective or new properties the geostatistical model is more attractive due to its ability to construct confidence limits on the estimates.

Jan 1, 1978

By R. A. Burmeister, G. P. Pighini, P. E. Greene

An open tube vapor phase epitaxial growth system has been used for large area (multiple substrate) growth of GaAs1-xPx on GaAs substrates. The GaCl-GaCl transport reaction is used with either a GaAs or Ga (nonsaturated) source. Selenium and tellurium have been used for donor impurities, and zinc as an acceptor. The useable substrate area in this system is approximately 20 sq cm. The uniformity of thick-ness of the epitaxial layers are typically better than ±5 pct across a given wafer. Electrical and optical measurerments indicute comparable uniformity in electrical and luminescent properties within a wufer. The application of this system to the large scale pro-duction of GaAs1-x Px for display devices, both discrete and arrays, is discussed. Typical electrical and luminescent properties of light emitting diodes fabricated front material produced by this technique are presented. THE most promising materials currently being utilized for visible injection electroluminescence are GaAs1-xPx, Ga1-xAlxAs, and Gap. All have reasonably efficient emissions in the red portion of the visible spectrum at room temperature; Gap also has an efficient green emission.' At present, GaAs1-xPx has a technological advantage over Ga1-xAlxAs and Gap for display applications, since relatively large (several sq cm) areas of GaAs1-xPx suitable for use in electroluminescent devices may be readily grown by vapor phase growth techniques. In contrast, the preparation of Gap and Ga1-xAlxAs for electroluminescent device applications generally employs solution growth techniques which are at present not well suited for the growth of large areas of uniform thickness and doping level. The capability of uniform growth over large substrate areas and the use of multiple substrates is necessary for the practical utilization of electroluminescent devices. This is particularly important when quantity production or monolithic devices are required. Furthermore, in many display applications arrays of light emitting devices are used, the individual elements of which are of a size resolvable by the unaided eye. Thus the overall dimensions of display are substantially larger than those of most semiconductor devices. It is also necessary to achieve a high degree of control over the growth parameters to attain the required degree of reproducibility of materials properties for electroluminescent devices. In the case of GaAs1-xPx it is necessary to accurately and precisely control the phosphorus content of the alloy, both on a macroscopic and microscopic scale, in addition to the parameters generally associated with epitaxial growth such as thickness and doping level. This value is critical, as it has a major effect on the performance of electroluminescent devices. This paper describes the epitaxial growth of GaAsl-xPx suitable for electroluminescent display devices using a system developed specifically for this purpose, and which contains several novel features. The results of studies of selected physical properties of the epitaxial layers are also discussed. Finally, a brief summary is given of the characteristics of display devices fabricated from GaAsl-xPx grown in this system. EXPERIMENTAL A) Reactants. A number of techniques suitable for the vapor phase epitaxial growth of GaAs1-xPx have been reported in the literature.'-' The method selected for this investigation is that in which the Ga is transported by the GaC1-GaCI3 reaction in an open tube process. The results reported here were obtained using either the combination of GaAs, AsC13, and pH3, or Ga, AsH3, pH3, and HC1 as the initial re-actants.* The ASH3 and pH3 were obtained as dilute *Several different sources of supply were used for these reactants, y~elding comparable results._____________________________________________________ mixtures in HZ; the HC1 was obtained from the reduction of AsC13 by Hz at elevated temperatures. Both selenium and tellurium were employed as donor impurities, and zinc as an acceptor impurity. Selenium was introduced in the form of H2Se, tellurium in the form of tellurium-doped GaAs, and zinc in the form of diethy1 zinc. B) Apparatus. The prinicipal difference between the apparatus used in the present study and that of Tietjen and Amick,8 in addition to size and other related design features, is that RE induction heating is utilized in place of resistance heated furnaces. Induction heating was selected for this application because it appears to have several advantages, including: 1) It is possible to keep all fused silica portions of the apparatus at temperatures well below those of the reaction zone, thus minimizing a possible source of contamination. 2) The thermal mass of an induction heated system can be made small, thus reducing the total time required for the growth process. 3) Sharp temperature profiles (desirable for high deposition efficiency) are easily achieved. 4) The volume of the system for a given substrate area can generally be made smaller than a comparable resistance heated unit. This results in shorter time

Jan 1, 1970

By Carl E. Swartz

For many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By A. W. Hesse

Ventilation of all types of coal mines is fundamentally the same, in that sufficient air must be provided to properly dilute and remove dangerous and obnoxious gases and leave the oxygen content of the air not under 1 9 per cent in all places where men and animals must work. Perhaps animals should not be mentioned, as the speed of mechanical loading leaves livestock behind and outmoded. Since this paper has to do with the influence of mechanical loading equipment on ventilation, the problems will be confined to the splits and the coal-producing places of the mine. The removal of coal dust from the air, or its rapid transmission to the return air courses; the possible increase in the liberation of gases by the multiplication of cuts in the coal made during one shift or multiple shifts; and the additional electrical equipment at the faces, are the factors that cause the added importance to good ventilation in the permissible equipment area of gassy bituminous coal mines. Ventilation tor Mechanical Loading in Gassy Mines In gassy mines, the air currents must be maintained across the faces in such a way as to prevent short cuts to the returns and leaving pockets in which accumulation of gas might occur. To do this, two or more doors are required on almost every entry containing a track to the face, so located that in no event will a trip of cars block open the doors and permit the air to bypass some place or places on the air-approach side. This method frequently requires the use of unusual lengths of duplex cables to reach the mechanical equipment at the faces, particularly where the distances between parallel working places are 100 ft., as at the Nemacolin mine. Fig. I shows a pillar section being worked with mechanical loaders. This layout requires carrying the air in on the right and releasing it on the left, because the track clearance is on the right side and the line brattice is built on this side from the last crosscut to the face. Thus, the air travels to the face with greater velocity and gives more assurance of sweeping out the gas that might be exuding from the crevices of the coal. All working places, in driving through solid coal, are thus treated alike. They are all potentially gassy and must be swept clear of whatever may contaminate the air. Once the air starts into the working section, it is not released until it does a good job. Of course the volume of air must be large enough not only to dilute the gases but to carry away explosive fumes and fine coal dust quickly. Mechanical loading entails cutting and drilling of the coal during the same working period as the loading when two-shift and three-shift operations are employed, and all three processes create finely pulverized coal, which in itself is hazardous if not controlled by some means. If the ventilation is inadequate and gas accumulates, and a spark from defective electrical

Jan 1, 1942

By J. E. Worthington, W. H. Spence, I. T. Kiff

Gold was discovered at the Haile mine in Lancaster County, South Carolina, in 1827 or 1828, and since that time the mine has been worked intermittently by both open-pit and underground methods until its forced closure in 1942 by World War II. Production figures are incomplete, especially for the early years, but the total gold produced is estimated to have been greater than 200,000 oz. Thus, the Haile mine has been the most productive gold mine in the eastern United States. The upper, residually enriched ores were relatively rich, but the bulk of the production has come from the mining of lower grade ores. General Geology The Haile mine is located in late Precambrian or early Paleozoic rocks of the Carolina slate belt at the edge of the Atlantic Coastal Plain [(Fig. 1)]. The metamorphic grade is lower greenschist facies and the rocks have been folded into a sequence of northeast-trending isoclinal folds. The gold is associated with siliceous, pyritic, and kaolinized felsic pyroclastic and tuffaceous rocks in an interbedded volcanic and volcanoclastic sequence of felsic to mafic tuffaceous rocks and argillaceous sediments [(Fig. 2)]. The ore bodies occur in two northeast trending zones approximately 500 m apart; each zone is 30-70 m wide and 600 m or more in length, with possible extensions to the east beneath the Coastal Plain sediments. Mineralogy. Gold in the Haile mine is always associated with siliceous and/or pyritic ores. The gold occurs in at least three states: As native gold as originally deposited; as residual gold derived from the breakdown of pyrite; and as gold included in pyrite. Major associated minerals in addition to quartz and pyrite are kaolinite, sericite, and iron oxides. Minor molybdenite, arsenopyrite, pyrrhotite, copper sulfides, sphalerite, rutile, and topaz are also present. Petrology. The gold-bearing ore zones vary from highly siliceous rocks to pyritic massive sulfide lenses. This variation is most easily seen today along strike from the Haile pit to the Red Hill pit. Ore grade material still exposed in the wall of the Haile pit consists of a highly siliceous and very thinly bedded rock containing minor pyrite. Along strike, the character of the mineralization changes to pyritic massive sulfide lenses occurring interbedded with siliceous horizons at the Red Hill pit. The siliceous rocks vary from the thinly-bedded material as just described from the Haile pit to silicified fragmental-appearing rocks to totally recrystallized cherty rocks lacking any recognizable primary features. Scattered, apparently at random, throughout the very thinly-bedded and very fine-grained ore face of the Haile pit are seemingly anomalous silica-rich clasts or concretions up to 5 cm in diameter which will be discussed later in this paper. Alteration. One of the most striking features of the Haile deposit is the alteration mineral assemblage which is intimately associated with the siliceous and pyritic ores. This altered material has been intersected in drill core at depths greatly exceeding the modern weathering profile and is, therefore, of hydrothermal origin rather than from supergene processes. This "sericite," actually a fine-grained mixture of sericite, kaolinite, and quartz, can be shown to stratigraphically underlie the gold- quartz-pyrite zone, and is well exposed in the open pit just southeast of the Haile and Bumalo pits. Relict textures indicate that this highly altered material was originally a felsic ash flow. Other similar alteration zones have been found in outcrop and drill core underlying the remaining ore bodies. Thus each of the mineralized zones consists of two parts: A siliceous and/or pyritic gold-bearing ore zone which is stratigraphically underlain by a zone of high alumina minerals, in this case sericite and kaolinite along with variable amounts of quartz. A green chrome mica, presumably fuchsite, is present in trace amounts in the high alumina zone. Genesis An adequate model to explain the origin and distribution of the gold deposits in the Carolina slate belt is presently lacking. Worthington and Kiff1 suggested a volcanogenic origin for certain gold deposits in the North Carolina slate belt from the waning exhalations of felsic volcanic piles. They also pointed out that such an origin has similarities to many epithermal precious metal deposits located in more recent volcanic piles in the western United States. A further key to the understanding of the genesis of the gold mineralization at the Haile mine is the close association of the mineralization in siliceous and sulfidic horizons to the genetically related and stratigraphically underlying high alumina alteration. Such high-alumina alteration is common around felsic volcanic centers in the Carolina slate belt and the mineralogy as seen today consists of some combination of kaolinite, sericite, pyrophyllite, kyanite, andalusite or sillimanite depending on the local prevailing grade of metamorphism. Accompanying the high-alumina alteration are large quantities of pyrite and iron-oxide minerals as well as characteristic minor accessory minerals often including base metal sulfides, fluorine-bearing minerals (topaz, fluorite, apatite), titanium-bearing minerals (ilmenite, rutile),

Jan 1, 1981

By J. B. Wagner, B. Swaroop

The atomic ratios of oxygen to iron in zlarious corn-posilions of wustite in the vicinity oj the reported p to n transformation were determined in the temperalure range between 950" and 1250°C. For these conditions, equilibrium vacancy concenrations have also been determined at vatious mixtures of C0,-CO. The data show a continuos introduction of iron vacancies as oxygen is introduced into wuistite. No phase change is observed with in the wuustite field. However, the value of n in the isothermal oxygen pressure dependence, the weight change shifts to 1ower values as the concentration of oxygen increases. WUSTITE is a metal deficit semiconductor with the majority lattice disorder being cation vacancies. Using the notation similar to that of Kroger and ink,' the dissolution of oxygen into wiistite using C02-CO mixtures is represented by, WHere v+! denotes a cation vacancy with k effective negative charges and kh • denotes k electron holes, h -. Applying the law of mass action and assuming a dilute solution of defects in the wiistite yields Where the square brackets denote concentrations. Furthermore, when k = 2 the cation vacancies are completely ionized, and both the concentration of cation vacancies and the concentration of electron holes are proportional to the third root of the ratio, PC /PCo. This analysis is valid for one particular mael based on an ideal solution at elevated temperatures (in this case t > 1000°C). At lower temperatures, it has been shown2 that the pressure dependence of the electronic conductivity changes in a manner which suggests that vacancies interact with or "trap" electron holes. At the very high concentrations of defects, 10'' to 10" per cu cm, these simple models no longer hold. Recently Tannhauser,3 Geiger et a1.' Bransky and Tannhauser; and Hillegas' have found an apparent p to n transformation in wiistite in the temperature range of 950" to 1300°C. This junction was found by thermoelectric and electronic conductivity measurements. Geiger eta1.' found that the electronic conductivity became almost independent of the oxygen pressure at high temperatures and oxygen concentrations within the experimental error. In addition, Vallet, Raccah, and coworkers6'7 have reported the existence of several "varieties" of wiistite which were reported to exist within what was heretofor presumed to be a

Jan 1, 1968

By Walter S. Lutz, J. T. Griffith

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By E. A. Gulbransen, W. S. Wysong

The behavior of tungsten and its surface oxides in oxidizing and reducing atmospheres and in high vacua at elevated temperatures is a question of considerable technical importance. The use of tungsten as a a Or as an important component in alloys in high temperature Oxidizing atmospheres has been limited because of the unprotective nature of its oxide film and the volatility of its oxide. This paper will present results of a micro-balance study of the following problems: (1) the oxidation behavior in the ternperature range of 25 to 550°C (') the reduction with pure hydrogen Of thin Oxide films formed On tungsten, and (3) the volatility Of thin Oxide films On tungsten. Tungsten is an interesting metal to study for the following reasons: (1) although the Oxide to to ratio is greater than one, the oxide is not considered protective, ('1 the meta1 readily Oxidizes at temperatures from 30" to 55o°C (3) the oxides WO² and WO³ are reduced at temperatures as low as 500°C. by hydrogen, and (4) the Oxide WO3 is volatile at temperatures from 800 to 1100°C. Literature The oxidation of tungsten in its thin film range has not been studied critically. In the thick film range Dunn3 has made the only systematic study. He found the oxidation rate to obey the parabolic rate law in the temperature range of 700 to 900°c. The temperature variation of the oxidation rate constant was found to follow an exponential law of the Arrhenius type. An inflection was noticed in the temperature plot of the rate law constant at 850 to 900°C. This was attributed to a phase change in the oxides, Schei14 has studied the oxidation rate at 500 and 700°C over long periods of time and found a linear rate law. This result was interpreted as evidence for the presence of a nonprotective film. Pilling and Bed-worth's5 analyses of the oxide volume to metal volume ratio would indicate that a compact protective film should form. McAdam and Geil6 have studied the oxidation of tungsten in the thin film range using the interference color method. A parabolic rate law was found. Their curves showed that tungsten oxidizes faster than nickel but more slowly than iron. The lattice structures found in the oxidation of tungsten surfaces have been studied by Hickman and Gulbransen.? They have reported that WO3 is the stable oxide in contact with the metallic substrate up to approximately 600°C while wo³ forms first at 7oo°c. Hagg and Magneli8 have recently reported a study of the lattice structures . observed in the tungsten oxidcs using the X-ray diffraction method. In addition to an a-phase WO3 and a '-phase WO2, they reported the existence of two new phases. A 8' phase, homogeneous between

Jan 1, 1949

By J. T. Griffith, Walter S. Lutz

The rainfall during the last six months of 1942 in Scranton and vicinity was 24.06 in.—only 4.35 in more than the average for this district in any equivalent period—yet that rain forced The Hudson Coal Co. to handle 38.8 tons of water for every ton of coal mined. It filled to overflowing, or to a higher level, 14 flooded mine areas holding, in total volume, 8.3 billion gallons of water in storage; brought about a pumpage of 11.4 billion gallons in the months of December 1942 and January, February and March 1943 Half of the total energy generated or purchased (44,322,980 kw-hr.) was required to keep the mines sufficiently free of water to permit the mining of coal during a period of much needed output. Fig. I shows the extent to which this flooding of exhausted and idle properties has proceeded, and is known to be proceeding further, at the upper end of the Northern field. This rainfall (24.06 in.) means 80,559,444 tons of water on approximately 46.2 sq. miles of area tributary to the pumping plants. During the high rainfall period, 72,687,661 tons went underground, being pumped at the stations in this territory. This means an inflow of 88per cent, a runoff of 12 per cent compared with 64 per cent during normal conditions in a normal region. During this period no floods, either surface or underground, had to be dealt with, although the streams and rivers were high on several occasions. In general, the rainfall for the first three months of 1943 can be described as heavy but not abnormal.9 These figures not only indicate the large volumes of water to be handled but, by their very size, they also emphasize that the mine-water problem is not to be conquered, at least from an economical standpoint, by merely buying and installing more and more pumps. Into the solving of this water problem must go much planning, adhering to the principle of keeping the highest percentage of water at the highest possible level for the longest period of time; the storage of huge volumes in sumps capable of being reduced after the flood inflow and at rates less than the inflow; plans for prevention of surface inflow; provision of the minimum of pumping capacity arranged to as nearly 100 per cent pumping load factor as is possible; intercompany joint pumping plants; the conducting of water from one plant to another and from one property to another over distances measured in miles; priorities in power to the threatening situations; and. balance of the necessities and dangers existent in one colliery over another, day by day, when quantities of water are running high. Despite these astronomical figures of water volumes, their disposal to the surface is accomplished reasonably cheaply because, although the annual cost of $575,020 is a large sum, the cost per ton is about 0.1168 cents. Credit for this goes

Jan 1, 1947

By J. N. Ong, J. P. Ratledge, J. H. Boyce

SINCE German operators opened the Tsumeb mine in the early 1900's, continuous operation has been interrupted only by enforced shutdowns during two world wars and the depression of the 1930's. Original metallurgical practice was blast furnace smelting. This was applicable only to low zinc ore, leaving large tonnages of high zinc ore to be stockpiled on the surface. A gravity concentrator using tables, buddles, and jigs operated for several years, but differential flotation of the ore did not get beyond the experimental stage. When the property was put up for sale by the South African Custodian of Enemy Property there was an estimated 434,000 tons of ore on surface dumps. The dump material, assaying 4.48 pct Cu, 15.8 pct Pb, and 10.9 pct Zn, had become highly oxidized during a stay of many years on the surface. But these dump ores had to be used in evaluating possible metallurgy because the shaft became flooded after the 1940 shutdown and underground ore was unavailable. Many companies examined Tsumeb but quickly lost enthusiasm because of the formidable metallurgical problems presented by the dump ore. However, on the basis of extensive test work, the present company decided that differential flotation would be successful and purchased the property after competitive bidding. Geology and Mineral Association is Complex The Tsumeb mine lies near the northern boundary of South West Africa at an altitude of 4200 ft. The village of Tsumeb is 335 air miles northeast of Wal-vis Bay, territorial port of entry. The orebody is a hydrothermal replacement deposit associated with an irregular intrusion of aplite cutting folded pre-Cambrian dolomite beds. In plan the deposit is a lens of 250x600 ft maximum dimensions. In section the orebody dips 55" south from the surface to 2000 ft, below which there is a reversal in dip to 75" north. Mineralization is localized in the aplite and in the adjoining brecciated dolomite. In the upper levels the ore is largely confined to a single lens, but below the 1890 level massive sulphide ore forms north and south lenses that partially enclose a pipelike body of medium to low grade disseminated ore, part of which is of too poor a grade to mine. Drilling below the 24th, or bottom level, has disclosed that a high percentage of the mineralization from the 3000 to 3300-ft horizons is comprised of copper and lead oxides. The deep oxidation may be local, since it appears due to circulating waters in a major fault cutting the orebody. Tsumeb ranks as one of the highest grade base metal deposits in the world. It is geologically and mineralogically famous for 41 copper, lead, zinc, vanadium, and germanium ore minerals, but its complex mineral assemblage is not attractive to metallurgists. In addition, there is a gradual change in oxidation intensity from the upper levels to the lowest level now operating, which is the 24th. This is well illustrated by the copper minerals. In the upper levels malachite and azurite are predominant, in the intermediate levels chalcocite, and in the lower levels tennantite. Throughout the mine there are sufficient heavy metal soluble salts to activate zinc, and large amounts of depressants are required even for so-called clean sulphide ores. When the same sulphide ore is exposed to prolonged oxidation aboveground, as was the case with the dump ores, reagent requirements become fantastic. Plant Construction First staff members arrived at Tsumeb in March 1947, and by May essential services had been restored and mine unwatering began. In 2 1/2 months company employees built a temporary jig and sorting plant for treating existing dumps to provide a saleable product during high metal prices. Meanwhile, concentrator design and construction was contracted to a South African firm, with subcon-

Jan 1, 1956

By Fernando A. Buttazzoni, Jorge C. Munita

INTRODUCTION To provide a background for discussing long-range financial and operational planning in the mining industry, we would like to begin by describing the role of planning in Codelco. Having taken part in Codelco's planning process since its inception in 1976, we believe that useful conclusions may be drawn for the experience we shall relate. Although Codelco is a state-owned copper producer with an important role in the Chilean economy, and is consequently very much at the core of national economic planning, the following discussion is not related to government planning but to planning in an operationally and commercially autonomous business concern with all the characteristics of a private enterprise. The only way in which Codelco differs from private business is that its financial successes or failures have a more direct impact on the countryls ability to participate in international trade, to meet its international financial commitments and to achieve economic and social growth. Thus, what follows is a presentation of the conceptual features of the planning process at Codelco and a description of the current state of planning in the company. It is understood that certain conceptual components are basic to any formal strategic planning process, and that the components of Codelco's planning process are therefore generally applicable in similar companies. First, the mission and scope of operation of the company must be defined, and goals must be set to achieve leadership in the business activities in which it engages. Having set this framework, the company must constantly scrutinize those internal elements and conditions that are essential to fulfill its mission and achieve leadership. In Codelco this means considering the actions which can best serve to define future capacities, taking into account declining ore grades and determining optimal production levels; watching over the productivity and skills of its labor force, and; keeping abreast of technological developments in non-ferrous mining and processing. If the company is proficient in these three areas, it will be cost efficient and there- fore competitive. Codelco must also watch over the business environment in which it operates. The company sells concentrate, blister and fire-refined copper, wirebar, cathodes and wire rod and must study the behavior of the market to attune its product mix to the demand existing for these various commodities in the international market and the copper consuming industries in general. By examining the internal and external environment in which the company conducts its production and commercial operations, it is able to diagnose its strengths and weaknesses, to identify the hazards it must overcome to stay ahead in the copper trade, and to take full advantage of business opportunities as they arise. CHARACTERISTICS OF CODELCO-CHILE Although our subject is Codelco, readers should keep in mind that there are many other copper producing operations in Chile, all in the private sector, and many valuable deposits that may be exploited in the future. Codelco is the only public sector copper producer, although there is one other state enterprise that operates smelting and refining facilities principally to serve a large number of very small producers of copper concentrate. In the mid-19801s, Codelco is the largest copper mining company of the world and the largest producer and exporter of copper with yearly sales totalling close to US$ 1.8 billion in 1983. Moreover, it is a highly profitable copper company at a time when the world copper industry as a whole has reported losses for several years. Codelco-Chile is a fairly new organization. The history of the four mining operations it manages is much longer: El Teniente was opened in 1912, Chuquicamata in 1915, Salavador in 1959 -- with installations of the old Potrerillos mine dating from 1927 -- and Andina in 1970. Having had separate owners, the management systems of the

Jan 1, 1985

By Thomas C. Wilder

ALTHOUGH there is an abundance of thermodynamic information available in the literature today, no experimental data on the standard molar properties of formation of zinc oxide have ever been reported for the temperature range 419.5" to 908°C. This is the temperature range for which zinc metal is a liquid. so that the formation reaction is: Data have been reported for Reaction [I] where zinc is a solid or a gas. Maier. Parks, and nderson' measured the electromotive force of the cell: in order to obtain the free energy of the reaction: over a limited temperature range. With the known properties of H2O, those of ZnO were calculated. These workers found that t;j of ZnO is -75,930 ± 150 cal per gfw and Mtf is-83,000 300 cal per gfw at 25°C. akolkin made similar measurements to obtain ilF7 and AH; of -75,870 and -82,540 cal per dw respectively at the same temperature. Truesdale and arirlg and Kitchener and 1gnatowicz4 measured the equilibrium of the reactions: respectively, in order to determine Ff of ZnO from the known values of CO, CO2, and H/X The thermodynamic properties of ZnO, presumably taken from the above investigations, are tabulated by Kubaschewski and vans' and Wicks and Block" The latter reference also gives values for the range where zinc is a liquid. These numbers are probably acquired from the known extremities of the range plus Cp data of the components. In the present work the electromotive force of the cell: was measured in order to calculate the properties of ZnO from the well known values of NiO for the temperature range where zinc is a liquid. In Cell [B] the cathode reaction is: and at the anode: The overall reaction is: for which the free energy change is: where is the electromotive force in volts of cell [B] after correction for the Pt-Ta thermocouple. The standard molar free energy of formation of NiO is very well known as a function of temperature. Kiukkola and agner's data are used in most tabulations. The error is probably less than I00 cal per gfw, The latter authors were the first to use solid mixed oxide electrolytes in galvanic cells. Their work with NiO and other oxides was performed with cells similar to Cell [B] using a variety of reference electrodes of fixed oxygen potential. There may be a small composition range for which either NiO, ZnO or both exist. If nonstoichiometry does exist for these oxides, then the properties described herein are those for the metal saturated compositions. The simple cell design was the same as described elsewheres except that the molten metal electrode was about 125 g of pure zinc including a small (0.25 to 0.50 g) amount of ZnO. The mixture of pure nickel and NiO powders making up the reference electrode was contained in a tube of the ZrOl + CaO electrolyte which was immersed in the molten zinc. A platinum contact was made to the reference electrode; tantalum to the zinc. A refractory cement plug was necessary at the open end of the electrolyte tube in order to prevent zinc vapor from contaminating the reference electrode. Experimental details such as the vessel containing the cell, furnace, temperature control and measurement, and electromotive force determinations of the cell have all been outlined previously. The temperature was varied randomly in the range between the freezing and boiling points of zinc. After each temperature change, time was allowed for the drift at the new temperature to be less than +;"c whereupon a series of three cell readings was taken at least 10

Jan 1, 1970

By McAuliffe, Eugene

THE TERM "engineer" has been defined in many ways by many men broadly speaking the statement that "an engineer is one versed in or practicing any brar1c.h of engineering" is sufficient. A rather close relation exists between the sciences of surgery and engineering. A successful surgeon must have the capacity to perform the most delicate work, under extremely circumscribed conditions. This portion of his education is purely mechanical and although marvellous in itself, it must remain secondary to that greater possession, a thorough knowledge of human anatomy coupled with a comprehensive understanding of human psychology. In sub- stance, the surgeon must not only know how to operate but what is more important, he must be able to decide when, if ever, the operation should be undertaken.

Jan 1, 1932

By Y. Wang, M. M. Singh, H. L. Hartman

Knowledge of the state of stress at the bottom of a drillhole is of practical importance in rock drilling, since the induced stresses must exceed the strength of the rock in order to cause fracture. This note reports on a numerical method to determine the stress distribution at the bottom of a borehole induced by a static bit load and overburden and fluid pressures. The procedure adopted is similar to that for the plane-strain, discrete model employed by Harper and Ang.1,2 The rock medium is considered to be homogeneous, isotropic, and elastic-perfectly-plastic. METHOD OF ANALYSIS AND PROGRAMMING The discrete model adopted consists of two types of points: mass points and stress points. The configuration and numbering notation are depicted in

Jan 1, 1967

By Alan K. Burton

Along with tires and transmission systems, engines have been a limiting factor in the growth of large off- highway trucks. The problem, primarily, has been the development of reliable, high-performance engines that are not prohibitively heavy or expensive. For many years, horsepower to overall truck weight ratios have been in the vicinity of 300 lb per hp for rear dump units up to 50 tons capacity. This ratio is obviously very poor when compared to the much lighter and smaller highway trucks, which frequently have a performance ratio of 100 lb per hp. Unfortunately, the larger mining trucks have not been able to match even the 50-ton trucks, and in some cases, ratios have dropped as low as 450 lb per hp. This results in a performance of only 67% of that achieved by the older smaller trucks. Thus, the message is clear: what is needed is more horsepower and less weight.

Jan 10, 1975

By R. E. Zimmerman

THE separation of fine sizes of coal from its impurities by means of various flotation methods has become of increasing importance in the coal industry. This, no doubt, will be even more so in the future as the quantity of high grade coal is depleted, particularly that used for metallurgical purposes. The purpose of this paper is to describe and report the results of research work done under the auspices of the Pittsburgh Coal Co. to determine the amenability of their bituminous fine sizes of coal to flotation, to investigate the value of various reagents and factors affecting their use, and compare the results between froth flotation and bulk oil flotation. Compared with the preferential flotation of complex minerals, or ores, the flotation of coal is comparatively easy. However, this statement should not lull one into the feeling that there are no special problems involved. For instance, the separation of coal from pyrite in high sulphur coals is still far from being 100 pct successful. Size consist has considerable effect on reagent consumption and recovery. Other factors will be described and finally it must be remembered that in the flotation of coal a low priced material is being treated and thus economic considerations govern more closely its application than is generally the case in treating other minerals. As a result of the research work done by the Pittsburgh Coal Co. on the flotation of coal, it was concluded that it was practical to clean the -48-mesh coal commercially by froth flotation and after several different types of flotation units and circuits were investigated by means of pilot plants, large scale units were installed at their Champion Nos. 1, 4 and 5 Preparation Plants for the cleaning of -48-mesh slurries. These large scale operations have been recently described by D. H. Davis. 1 C. P. Proctor and C. B. Carlson2 in their chapter on Froth Flotation of Coal in the AIME Seeley W. Mudd series book on Coal Preparation describe some of the practical applications of our Pittsburgh Coal Co. laboratory work in actual plant practice as well as summarizing part of the investigational work. The author presents this paper, however, as a supplement to their reports, and records the basic research accomplished in the laboratory investigational work as well as the results of experi¬ments using bulk oil flotation. In presenting this work the author wishes to state much more work must be done in applying the principles of flotation to cleaning coal, especially in view of recent studies and practices in other mineral beneficiation fields. METHODS OF CONDUCTING LABORATORY TESTS The bulk of the research work was conducted in the laboratory of the Champion No. r Preparation Plant. This plant has elaborate facilities for sampling and analyzing coal and proved to be an admirable location

Jan 1, 1948