Search Documents

By W. F. Kieschnick, C. C. Miller, E. R. Brownscombe

The possibility has been mentioned that large pressure gradients in a solution gas driven field caused by high production rates might lead to a reduction in the ultimate recovery obtainable compared to that which would be obtained by a very slow rate of production. In the present study the reservoir conditions accompanying a high rate of production and the corresponding ultimate recovery were compared with those obtained if the reservoir were produced at some marginal rate throughout its entire life. The method of calculation involved the application of fluid flow - material balance analysis to a series of successive steady state conditions in the reservoir. In the case studied very little difference in recovery was obtained at the abandonment pressure. An analysis of the basic factors involved indicates that the sane results would hold for considerable variation in properties of reservoir fluids, permeability of the formation or well spacing. Even if the reservoir has a water drive it appears that no harm will be done by- open flow production if the rate is cut back before any appreciable free gas is produced. However, any condition which leads to disproportionate withdrawal rates and which causes large pressure differences over large areas might result in substantial loss in ultimate recovery. INTRODUCTION When the pressure declines in a reservoir, gas is evolved from solution causing a shrinkage in the reservoir oil so that a stock tank barrel of oil with its residual dissolved gas occupies a smaller volume than originally. For a given reservoir oil saturation, therefore. stock tank oil content will be higher at the lower pressure. At the same time the evolved gas which remains in the reservoir reduces the reservoir oil saturation, and this would be expected perhaps to cause a reduction in stock tank oil content. However, around the well the shrinkage occurs so rapidly that stock tank oil may actually accumulate in this region in spite of the simultaneous reduction in reservoir oil saturation. If this accumulation should continue, spreading into a larger zone, the loss might be appreciable and because larger pressure gradients accompany higher rates the accumulation might possibly be large if wells are produced at too high a rate. It is the purpose of this paper to determine the effect of rate of flow on ultimate recovery by solution gas drive. The problem under consideration involves the unsteady state flow of oil in a closed radial system from which oil is produced by the evolution of gas as a finite drawdown is estalllished and the reservoir pressure declines. A somewhat similar unsteady state production problem dealing, however, with a linear system has been considered by Muskat and Meres, but these authors do not discuss the effects which rate may have on recovery. Other methods have been reported for estimaling recovery as a function of pressure decline when producing at an infinitesimal rate, and Muskat and Taylor' have shown the effect of fluid and reservoir characteristics on recovery under these conditions. Assuming steady state to exist, Babson has given a procedure for computing the decline in well productivity as the field is depleted, and Moyer has combined these methods to estimate abandonment conditions and the resulting ultimate recovery. These latter approaches to the problem either do not consider the effect of rate or assume steady state can be established. In detail this paper presents the behavior of the reservoir producing under unsteady state conditions and considers the effect of production rate during this unsteady state flow on the recovery attained. The analysis also shows that there will exist at abandonment a type of steady state, and on this basis a method has been clevelopetl for rapid calculation of abandonment conditions.

Jan 1, 1949

By C. C. Miller, W. F. Kieschnick, E. R. Brownscombe

The possibility has been mentioned that large pressure gradients in a solution gas driven field caused by high production rates might lead to a reduction in the ultimate recovery obtainable compared to that which would be obtained by a very slow rate of production. In the present study the reservoir conditions accompanying a high rate of production and the corresponding ultimate recovery were compared with those obtained if the reservoir were produced at some marginal rate throughout its entire life. The method of calculation involved the application of fluid flow - material balance analysis to a series of successive steady state conditions in the reservoir. In the case studied very little difference in recovery was obtained at the abandonment pressure. An analysis of the basic factors involved indicates that the sane results would hold for considerable variation in properties of reservoir fluids, permeability of the formation or well spacing. Even if the reservoir has a water drive it appears that no harm will be done by- open flow production if the rate is cut back before any appreciable free gas is produced. However, any condition which leads to disproportionate withdrawal rates and which causes large pressure differences over large areas might result in substantial loss in ultimate recovery. INTRODUCTION When the pressure declines in a reservoir, gas is evolved from solution causing a shrinkage in the reservoir oil so that a stock tank barrel of oil with its residual dissolved gas occupies a smaller volume than originally. For a given reservoir oil saturation, therefore. stock tank oil content will be higher at the lower pressure. At the same time the evolved gas which remains in the reservoir reduces the reservoir oil saturation, and this would be expected perhaps to cause a reduction in stock tank oil content. However, around the well the shrinkage occurs so rapidly that stock tank oil may actually accumulate in this region in spite of the simultaneous reduction in reservoir oil saturation. If this accumulation should continue, spreading into a larger zone, the loss might be appreciable and because larger pressure gradients accompany higher rates the accumulation might possibly be large if wells are produced at too high a rate. It is the purpose of this paper to determine the effect of rate of flow on ultimate recovery by solution gas drive. The problem under consideration involves the unsteady state flow of oil in a closed radial system from which oil is produced by the evolution of gas as a finite drawdown is estalllished and the reservoir pressure declines. A somewhat similar unsteady state production problem dealing, however, with a linear system has been considered by Muskat and Meres, but these authors do not discuss the effects which rate may have on recovery. Other methods have been reported for estimaling recovery as a function of pressure decline when producing at an infinitesimal rate, and Muskat and Taylor' have shown the effect of fluid and reservoir characteristics on recovery under these conditions. Assuming steady state to exist, Babson has given a procedure for computing the decline in well productivity as the field is depleted, and Moyer has combined these methods to estimate abandonment conditions and the resulting ultimate recovery. These latter approaches to the problem either do not consider the effect of rate or assume steady state can be established. In detail this paper presents the behavior of the reservoir producing under unsteady state conditions and considers the effect of production rate during this unsteady state flow on the recovery attained. The analysis also shows that there will exist at abandonment a type of steady state, and on this basis a method has been clevelopetl for rapid calculation of abandonment conditions.

Jan 1, 1949

By Blake M. Caldwell, Harrold D. Owen

The continued use of permanent-type, we11 completion Iras pointed LIP the need for more powerful through-tubing perforating equipment. A new expendable shaped charge perforator has been developed in which the charges are run through the tubing in a vertical position and then opened out to a horizontal position when at the desired shooting zone. The performance of this new tool is comparable to that of conventional casing type perforators. This paper describes the new tool and its applications. Performance data in targets rind under various actual well conditions are presented. INTRODUCTION The general acceptance and increasing use of pernianent-type well completion by the oil industry has indicated the need for through-tubing perforating equipment with performance comparable to that of conventional casing type perforators.'.' To achieve the performance desired, a new, expendable, shaped charge perforator has been developed with adequate power for effectively perforating both 51/2-in. and 7-in. casing below tubing. This has been accomplished without resulting severe damage to the casing and can he obtained under extremes of pressure and temperature. The design of this new tool is a radical departure from previous concepts of tubing guns since it was felt that the two major limitations imposed by previous designs severely handicapped performance. The first of these limitations was the restriction imposed upon the length of the charges by the necessary small inside diameter of the carrier. This resulted from the necessity for compromises in designing a hermetically sealed gun small enough to allow free passage through 2-in. tubing, yet with sufficient wall thickness to withstand some minimum pressure. In an effort to overcome this limitation, the charges were in some cases placed at an angle with the axis of the well with resulting loss in effective depth of penetration. The second limitation concerned the extreme distance of the charges from the casing when the gun was fired. An example of the latter situation is demonstrated by the fact that a conventional 13/4-in. tubing gun centralized in 51/2-in., 17-lb casing has a clearance of more than 1-9/16-in. on all sides. This means that a considerable portion of the force from each charge must be expended in penetrating this 1-9/16-in. of well fluid before it even reaches the casing. With the gun centered in 7-in., 23-lb casing, the amount of fluid penetration required of each jet is in excess of 21/4-in. In a situation where the 13/4-in. gun is touching one side of the 51/2-in., 17-lb casing, the jets from the charges on the opposite side have more than 3%-in. of fluid to penetrate. A similar situation in 7-in., 23-lb casing necessitates the penetration of more than 4-9/16-in. of fluid. The penetrating effect of the charges is severely impaired in passing through so much fluid. Under such conditions, there is usually insufficient force left to penetrate the casing. Previous studies have shown the decided disadvantage of having to shoot through such an excessive quantity of well fluid.'.' The problem. then, was how to position large powerful charges close to the casing prior to firing and still manage free passage through 2-in, tubing. The solution appeared to be in some method of folding sealed charge units in an open type, expendable. 13/4-in. carrier for travel through the tubing, and unfolding them upon their arrival at the shooting zone in the casing. It was desired to control the mechanism electrically from the surface through the regular shooting cable, making the release of the charges independent of the physical characteristics of the well, yet with a provision to prevent the gun from firing until the

Jan 1, 1955

By A. W. Fahrenwald

PRACTICALLY all fine grinding is done in a ball mill or some modification of a ball mill. Millions of tons of material are ground each year. The cost varies from, say, a minimum of 10 c. to a maximum of 35 c. per ton. It is thus obvious that even small improvements, which may result in increased grinding efficiency, would be welcomed by mill operators. A review of literature shows that various phases of the subject have been studied independently by many investigators. Also, it is now a subject of investigation at various laboratories in the United States and in foreign countries. Notwithstanding this extensive investigation, ball milling still remains a subject of some speculation. This paper presents the results of an experimental study of some of the factors entering into ball mill grinding.

Jan 1, 1931

By AIME AIME

ARGUMENTS and discussions were not lacking either Wednesday or Thursday mornings, when the geophysicists got together. The first session, under the chairmanship of Paul Weaver, was devoted largely to theoretical papers, except for the first one by F. W. Lee, which was a progress report. This speaker mentioned some of the high lights of geophysical exploration during the last year, such as the recently announced extension of the Rand gold fields through magnetic exploration, and the continued activity in the oil fields of this country. Even this brought forth some disagreements, Paul Weaver feeling that credit was being given geophysics where it was not due for the discovery of certain oil fields. In this criticism Everette DeGolyer concurred, and both agreed that geophysicists must lean over backward when it comes to taking credit for discoveries. The troublesome question of interpreting resistivity curves is always being aired, and Lynn G. Howell's paper, presented briefly by the chairman, served to clear up a moot point raised last year by M. King Hubbert's work. By use of Maxwell's theory of images the author calculated that the effect of a thin, conductive sheet placed perpendicularly across the middle of a four electrode system should bring the resistivity curve up to a figure equivalent to the resistivity of the surrounding medium, but no higher. Variations from this he explained as being due to dirt on the surface of the sheet. The difficult question of interpreting three-layer curves was tackled bravely in Thomas Manhart's paper, presented in abstract by S. F. Kelly. The author seems to be attaining some success through dividing three-layer curves into two approximation curves of the two-layer type.

Jan 1, 1933

By G. D. Arsdale

This paper describes a series of experiments leading to the development. of a method for leaching the mixed ores of the Inspiration Consolidated Copper Co., containing chalcocite and silicates of copper, by the use of solutions acidified with sulfuric acid and carrying ferric sulfate. Iron is added to the solutions and ferric iron is regenerated electrolytically to a percentage high enough to act as an efficient solvent. The decreased yield is partly compensated for by a higher current density. AN IMPORTANT problem in modern copper metallurgy, particularly in the Southwest, has been to obtain good recoveries from what are commonly known as mixed ores; that is ores in which the copper occurs partly as oxide and partly as sulfide compounds. The dividing line between mixed ores and ores commonly accepted as concentrating is not definite. In other words, much ore now being concentrated carries considerable copper in non-sulfide form, on which recoveries are hot so good as on ores carrying less of these constituents. While treatment by concentration may be commercially profitable, on ores carrying oxide copper within certain limits, there are large deposits for which the application of con-centration could not be considered, and yet which have not been considered amenable to leaching because they carried too much sulfide. The Inspiration Consolidated Copper Co. has large amounts of such mixed ores, and this paper is an account of the experimental work by which a method was developed for their treatment, and for which a large plant is now being erected by the Inspiration Co. It is not claimed that the method is a general solution of the problem of mixed-ore treatment but it is apparently well adapted for leaching the ores of the Inspiration Co., for which it was designed. The work done has covered preliminary laboratory and test-plant investigation, and .a pilot-plant run, extending from March to the middle of December, 1923. Thoroughly consistent and satisfactory results, were obtained continuously for more, than six months in the pilot plant; and it is believed that the results; and probable costs that can be had on a large scale have been definitely, proved. The method, however, was designed for local conditions; and while the basic principles are general, there are ores on which it will not work and other ores for which considerable modification may be required.

Jan 10, 1925

By W. F. Flanagan, D. H. Polonis, S. D. Dahlgren

Rotation diffraction patterns of Cu-4.84 wt pct Si polymystalline samples were taken during the course of isothel-ma1 affing of the suPersaturated a phase, a diffraction spots were obserzled to streak during the initial stages of aging, and this streaking was similar to the streaking of a spots observed earlier by Barvett with deformed super saturated samples of the same composition. Although it was suggested that stacking faults were the sole cause of styeaking in the deformed samples, the present study has shown that plates with one small crystallite dimension can also contribute to the streaking when there is lattice coherency across close-packed planes. THE decomposition of the supersaturated a phase in Cu-Si alloys has been reported to occur by means of both thermal and stress activation.1-4 According to the Cu-Si phase diagram,3 Fig. 1, the supersaturated a phase (fcc) is expected to transform during aging by the precipitation of the y phase. The results of earlier studies2,4 have indicated that metastable k phase (hcp with nearly ideal close packing) forms initially at temperatures below the eutectoid temperature, after which the k transforms to the a and y phases. Hof-mann et al.4 have proposed a metastable version of the phase diagram, showing the approximate boundaries for k formation below the eutectoid temperature. In view of the close-packed nature of both the a and k phases, it is essential to consider the role assumed by stacking faults in the transformation. Streaking effects have been reported by Barrett 1 in the rotating crystal X-ray patterns of strained Cu-Si alloys and were attributed to stacking faults rather than particle size effects. This deduction was based on the observation that streaks in the diffraction patterns did not occur tangent to the 220fee Debye ring. It is known that the atom movements involved in faulting leave some X-ray reflections unaffected while others are broadened,' and, in particular, it has been shown that faulting will not cause streaking of 220fee reflections tangent to the 220fee Debye ring as would be expected if all the reflections were broadened.' The formation

Jan 1, 1967

By Edwin R. Phelps

In the year 1900 about 212 million tons of bituminous coal were produced in the United States. Almost none of this was produced by surface mines (Fig. 1), because there was no large equipment suitable for stripping overburden at that time. By 1915 the surface mines had built up their capability largely through use of the steam shovel to the point that they produced 2.8 million tons of the nation's total production of 443 million tons. Over the intervening years between 1915 and 1970 surface mining provided a continually increasing percentage of the nation's bituminous coal, stimulated by the growing availability of giant surface mining machines, some of which are presently capable of removing 220 cu yd of earth with one bite of their mighty buckets. In 1970 the nation's surface mines produced 244 million tons of bituminous coal, over 40% of the total national production. On the other hand, the nation's underground mines hit a peak of 560 million tons in 1920, dropped to a low of 273 million tons in 1961, and are presently on a very slow rise. Environmental pressures generally oppose surface mining, and have forced coal companies to consider more underground mining in future planning. Also, since strippable reserves are decreasing in the eastern states, an increase in underground mining is expected over the coming years. However, in the western states there are enormous reserves to be extracted by surface methods. Why has surface mining increased, while underground mining has decreased? It's largely a matter of economics. The cost per ton is greatly reduced by surface mining because of the relative ease of obtaining the coal. Also, there is a much greater percentage of coal recovery-nearly 85% in surface mines within the minable area, as compared to an average of about 50% in underground mines. Much surface mining recovers coal that could not be extracted by underground methods because of coal bed thinness, or multiple beds close together, split seams, the nature of the roof, and other geologic conditions. What are some of the limitations of surface mining? First of all, with presently available machinery it is difficult to surface mine at depths

Jan 1, 1973

By R. E. HORE, J. B. Tyrrell

IN the vicinity of Kirkland Lake, northern Ontario, several gold mines are producing, and three are at present being operated very profitably. At these three mines and on the adjoining properties east and west of them there have been important developments during the past year, and additional equipment has been installed to permit a large increase in output. At the end of 1924 the total production amounted to $13,688,600. For the year 1926 the production is estimated at about $19,000,000, and during 1926 the output should be much greater than that of 1925. The mines which are being operated most profitably and are producing a large part of the ore now being milled are the Wright-Hargreaves, Lake Shore and Teck-Hughes. Others which have contributed smaller amounts are the Tough-Oakes-Burnside and the Kirk- land Lake Gold mines.

Jan 1, 1926

By J. G. Balkestein, J. W. R. Baerts

During an attempt to develop a method for accurate, rapid, continuous analysis of ash content of wal, the Dutch State Mines Laboratory found that the absorption coefficient for X-rays was related to ash content. This relationship was utilized in the development of an apparatus called CendreX, used to measure the absorption and in turn the ash content. The principle, procedure, accuracy, and applications of the CendreX automatic determination of ash in coal are discussed in detail. Until recent years coal preparation research was concentrated on the possibilities and efficiency of preparation equipment. Ever increasing demands for quality in coal, however, have caused researchers to become concerned with quality control. One of the characteristics strongly influencing quality (calorific value) and, consequently, the price of coal is ash content. Both customer and producer require that the ash content be controlled. To make this possible it is necessary for the producer to collect samples from the coal stream in the washery and to determine their ash content. On the strength of the results obtained the production process can then be adjusted, if required. Until recently incineration was the only method for determining ash content. When coal is incinerated with oxygen, it takes at least 15 min to determine the ash content. Even then some time may be lost in passing on the data. Therefore, this discontinuous and time-consuming method does not make a suitable starting point for checking, re-adjusting, or modifying the production process. Since it was not possible to accelerate incineration by mechanization and automation, another type of rapid continuous analysis had to be found. This would have to depend on some coal characteristic closely linked with ash content. At the Central Laboratory of Dutch State Mines, Dijkstra and Sieswerda found that the absorption coefficient for X-rays was suitable for this purpose. An apparatus based on the measurement of this characteristic was developed. Named CendreX,* this patented equip- *A Stamicarbon N. V. registered trademark. ment, used in combination with a sampler and conditioning apparatus, permits continuous determination of ash content with satisfactory exactness to within 3 min.t At the American Mining Congress meeting of May 1961, Log A. Updegraff, surveying aspects of continuous analyaia, reported on the CendreX appartus (Mining Congress Journal, August 1961). Since the first Condition for correct ash determination, whatever the method used, is always a sample taken in the right way, some practical aspects of sampling will be discussed first. SAMPLING In coal handling operations, each grain has its characteristic properties. In both the cross-sectional and longitudinal direction of the product stream the mixture of these grains is imperfectly blended. The elimination of the factor of segregation between the cross-sections from the direction of the stream is the principal aim of continuous analysis. Therefore, the samples to be analyzed are withdrawn in various places from the segregated product stream in such a way that they form a semi-continuous flow. In order to be truly representative of the product stream, the sample flow must fulfil two conditions: 1) The sample flow must be sufficiently large to insure that adventitious differences between the composition of the product stream and sample flow will be as small as possible. 2) All grains through the entire cross section of the product stream must have an equal chance to get into the sample flow. Since there is always a segregation through the cross section the sample flow will have a bias if the sampler collects only part of this section. In order to prevent the volume of the sample flow from becoming too large, the cross sections are taken discontinuously. However, this discontinuity gives rise to the adventitious differences that arise between the composition of product stream and the sample flow, and these differences become greater and are more deranging as the fluctuations follow each other more quickly. Moreover, the intervals between the morrnents of sampling mean a delay in the analysis. The aim will, therefore, be to collect small samples, or in other words thin cross-sectional increments, taken at sufficiently high frequencies. The following points should also be taken into account: 1) The smallest dimension of the openings in the sample collector must be equivalent to at least 3 d in

Jan 1, 1962

By W. A. Walker, G. W. Ostroot

An increase in the number of deep wells being drilled where extreme bottom-hole temperatures are encountered, and the anticipated drilling of wells where temperatures in the range of 500°F or higher may occur, has brought about a comprehensive investigation of cementing materials and of the techniques involved in their proper usage at these elevated temperatures. Included are developments in cements, retarders, weighting materials and other cement additives which make it possible to formulate a variety of compositions to help resolve the cementing problems of these extreme well conditions. The problems associated with the selection and testing of cements are discussed, and a resume of field results is included. Previous studies on strength retrogression indicate that caution should be exercised in the selection of a cementing composition for use in high-temperature wells. It now appears that, by the addition of silica flour as a stabilizing additive to certain cements, compositions covering a wide range of slurry densities can be designed to meet extreme well conditions without strength retrogression. Improvements in cement retarders make it possible to produce a four-hour thickening time at static temperatures up to 500°F. This temperature is considerably higher than conditions presently being encountered in drilling and completion work. Inert weighting materials, used to produce 20-lb/gal or heavier cement slurries, are reviewed. INTRODUCTION As the search for oil continues, the number of wells being drilled to depths of 10,000 ft or below has continued to increase over the past decade. During 1959, there were 50,893 wells drilled in the United States for a total of 209 million ft of hole. Of this total, approximately 4.45 per cent were drilled below 10,000 ft and 0.30 per cent below 15,000 ft, with a record depth of 25,340 ft recorded (Table 1). With the drilling of this record-shattering hole comes the question, "How deep can wells be drilled?".' Limitations with respect to equipment (surface and subsurface), cementing materials and techniques would cause some concern; however, a panel of experts have agreed that the U. S. oil industry has the equipment and know-how to drill a 50,000-ft hole. The greatest deterrent would be the 700°F temperature they would anticipate encountering at this depth. Although the number of wells drilled under what is generally considered hot-hole conditions (230°F and higher) has been relatively high, each well often presents distinctly individual problems and requires separate consideration and selection of special materials, techniques and equipment. At the present time there are over 30 additives and special cements available for use in "tailoring" a cementing composition for a specific well. It is not uncommon to use three or four different additives with the basic cement to produce the desired slurry characteristics. A generally accepted procedure is to make laboratory tests on selected cementing compositions prior to pumping them into wells deeper than 12,000 ft, or where static temperatures are in the range of 260°F or higher. In some instances, it is recommended that laboratory tests be made where less severe well conditions are encountered. Prior to selecting a cementing composition for a particular well, key personnel representing the operator, drilling contractor and service company should meet to determine that each individual is acquainted with every detail which might influence cementing results and to discuss the execution of the job. For cementing hot-holes, a number of factors must be evaluated before proceeding with the operation. Consideration must be given to the following. 1. Thickening time—The slurry must remain fluid for a sufficient length of time to allow displacement down the casing and up the annular space in a primary cementing job or, in squeeze-cementing, adequate thickening time for both the build-up of a satisfactory squeeze pressure and the reversing out of excess cement. The thickening time of standard retarded cements will often be too short under extreme temperature conditions, thus involving special formulations and requiring laboratory tests to determine the proper amount of additional retarder to obtain the desired pumpability.

By A. B. T. Werner, J. J. Schanz

A survey of the world's sources and markets for natural graphite and some predictions of future trends are presented here. The authors feel that there is no indication of major changes in sources of graphite over the next few years, but it is possible that the importance of domestic graphites as opposed to foreign carbons may increase in the more distant future. U.S. consumption of natural graphite, which has been in general decline for the past six years, and will probably continue downhill with the virtual disappearance of some markets. However, other markets such as bearings, brake linings and crucibles will probably grow. Natural graphite is the name given to all the naturally occurring mineral forms of carbon that crystallize in the hexagonal system. Natural graphite~ are generally divided into three broad classifications that are based on physical rather than chemical differences — crystalline flake, Ceylon amorphous and other amorphous. Crystalline flake graphites occur as thousands of small individual flakes disseminated throughout the ore and closely resemble shiny black fish scales. Ceylon amorphous graphite is mined from narrow veins of almost pure mineral. It is produced in lump form and often has a coarse platy or needlelike structure. Other amorphous graphites include all those that are extremely fine-grained and have a crystalline structure that is not visible under normal circumstances. In the primary raw material markets, the graphite's country of origin is also important. Crystalline flake graphites may, for example, be of the Alabaman, Bavarian or Madagascan types; Ceylon amorphous graphite may have originated in Montana or Ceylon; and other amorphous graphites may come from Mexico, Hong Kong or Korea. The distinctions between the graphites from each particular locality are small yet important, for the country of origin will signify certain inherent physical characteristics and will often give an idea of the amount of graphitic carbon contained in the shipment in question. .In certain instances, however, even this is not enough, since the actual mine at which the graphite is produced may have to be known before its true commercial value can be ascertained. Thus, the Madagascar flake graphite shipped from the Sahalambo mines of the Societe des Graphites de la Sahanavo is a thick flake which is known to be especially suited for use in crucibles, while the dull black earthy amorphous material formerly mined at Cranston, R.I., was ideal for stove polish. Synthetic, artificial, electric furnace and manufactured are terms used to describe graphites made from coke. These graphites will be considered in this paper only to the extent that they enter competition with natural graphite. DOMESTIC SOURCES OF NATURAL GRAPHITES Natural graphites have been produced from mines in Alabama, Alaska, California, Georgia, Montana, New Jersey, New York, North Carolina, Pennsylvania, Rhode Island, Texas and other states. The exception is the crystalline minerals resembling Ceylon graphite that have come from Montana and the amorphous meta-anthracites from Rhode Island. All the products mined have been flake graphite. In 1960, production was reported only in Texas and Pennsylvania. The Alabama graphite deposits of flake in quartz-mica schists are found southeast of Birmingham in a narrow belt that extends for about 60 miles southwest from Delta in Randolph County to Verbena in Chilton County. Since the long-run prospects for Alabama graphites appear to be fairly bright, especially if regular production of high quality output becomes possible, regional ore reserves of all kinds, including indicated and inferred, are estimated to be of the order of 25 million tons. Of this amount, 14 million tons are of the weathered variety. Alabama graphites are favored by their relative ease of mining, and by the fact that special methods of milling have been developed at the larger properties. In addition, the steady rise in ocean freight rates for Madagascar graphites, the tendency among crucible manufacturers to use flakes of a smaller size, and the possibility of producing other salable byproducts in addition to the graphite are favorable to Alabama producers. Against

Jan 1, 1962

By Richard D. Harvey, Arthur M. Squires, Robert A. Graff, George Kan

Particles of half-calcined dolomite (CaC03 + MgO) that had undergone cyclic absorption of H2S and regeneration with C02 in laboratory tests reveal enlargement of the crystallite grain structure, reduction in the number of pores but enlargement in their size, and partial development of a relatively dense mosaic microstructure on outer surfaces of cyclically reacted particles. Scanning electron microscopy, X-ray microanalysis, microprobe analysis, and X-ray diffraction techniques were used to evaluate microstructural properties of particles after tests conducted at pressures of 1 and 21 atm and temperatures of 7000 to 9000 C. The tests conducted at 7500 C and 21 atm showed the most favorable absorption and regeneration capacities of the dolomite tested. The changes in structure and pores play a major role in reducing the sulfur reactivity of half-calcined dolomite particles. The mosaic microstructure forms more rapidly at 1 atm than at 21 atm pressure. Once it occurs it seals the surface of the natural pore channels that existed in the half-calcined dolomite and restricts further conversion of crystallites of CaCO3 within the particles. Although a relatively coarse, granular mosaic of crystallites is present on some particles cycled at 21 atm pressure after only three absorption-regeneration cycles, it does not completely cover the particles, and that is true even after 30 cycles. Individual crystallites of MgO were not resolved by the X-ray microanalysis, but we believe that during the tests the MgO occurs as crystallites no more than 0.1 um in diameter that are homogeneously distributed through the particles, and it remains essentially inert during the reactions. The MgO contributes to the maintenance of the original fine-grained and microporous structure of the particles, an effect that is most advantageous to absorption and regeneration.

Jan 1, 1976

By James Douglas

Though liberality is not supposed to be a prominent trait of the Scottish character, Canada owes to a Scotchman, Sir Wm. Macdonald, more than to any other of its people, not only wise ideas, but pecuniary help towards extending education: and another Scotchman, in New York, has sumptuously housed under one roof three branches of the engineering fraternity, of which we are one. Having thus created us members of the same family—for the metaphorical meaning of house and kinship is identical—Mr. Carnegie expresses more emphatically than even he could in words, that, by aff'ording facilities for closest intercourse, he invites the mechanical, electrical and mining engineers to participate in the freest interchange of idea and experience, and to correlate and combine the results of their studies and activities; and, being members of the same household, to banish reserve and secrecy. And now we, the members of the American Institute of Mining Engineers, meet as though we were at home in a neighboring country. For whether we meet in Canada, in England, or elsewhere, the Institute is always received as though no political or geographical divisions separated its members from those of congenial associations in the land of its host. In truth, the title which we have assumed claims for the sphere of our activities the whole American continent, regardless of such trifling details as boundary-lines. The fact that we meet to communicate each other's experience, to discuss our difficulties, and to seek each other's aid in solving the intricate problems that so often present themselves in the course of our professional life, is an acknowledgment of our individual helplessness; and therefore an argument for united effort. But no effort can be of any value if there is an underlying suspicion

Jan 1, 1908

By Robert Mehl

THE precipitation of the nitride Fe4N from the solid solution of nitrogen in a Fe and of the phosphide Fe3P from the solid solution of phosphorus in a Fe both lead to the formation of structures that may be easily identified as Widmanstätten figures, within the meaning of the term as used in this series of papers. A complete solution has been obtained for the figure formed by Fe4N. The structure of Fe,P, however, is not fully known and a complete solution of this figure thus cannot be obtained; nevertheless, a study of this figure has furnished some new information. PRECIPITATION OF FE4N FROM ALPHA SOLID SOLUTION OF N IN ALPHA FE Constitution of System Iron-nitrogen A knowledge of the constitution of the whole of the Fe-N system is unnecessary for this work, though the recent studies by Eisenhut and Kaupp1 and by Lehrer2 have clarified most of the moot points; it is sufficient for our purpose to state that a Fe of high purity dissolves 0.42 per cent of nitrogen in solid solution at the eutectoid temperature, 591° C., and that this solubility decreases at first rapidly and then more slowly until at room temperature the solid solubility amounts to approximately 0.1 per cent nitrogen.3

Jan 1, 1934

By David A. Sterling, Roger C. Malan

The Atomic Energy Commission is investigating the distribution of uranium and thorium in the Precambrian of the western United States and the relationship of time-space-facies patterns of uranium and thorium enrichment in the Precambrian, to the major resources of umanium in Mesozoic and Cenozoic continental clastic sediments. The results of preliminary studies in the southwestern. United States are summarized. Approximately 50% of the uranium resource of the Free World is in deposits of Precambrian age, principally in lower Proterozoic conglomerates in Canada and South Africa (Uranium Resources, Joint Report, ENEA and IAEA, 1967). Most of the uranium resource of the United States is in Mesozoic and Cenozoic continental clastic sedimentary rocks that fill intracratonic basins. The Atomic Energy Commission (AEC) is investigating the distribution of uranium and thorium in the Precambrian of the western United States and the relationship of time-space-facies patterns of uranium and thorium enrichment in the Precambrian to the major resources of uranium in the Mesozoic and Ce-nozoic host sedimentary rocks. This paper summarizes the results of preliminary studies of the Precambrian in the southwestern United States including New Mexico, Arizona, southern Nevada, and southern California (Fig. 1). The host rock provenances for the major uranium resources in epigenetic deposits of Mesozoic and Ce-nozoic age in the western United States were in areas of extensive Precambrian exposure along the eastern margin of the Phanerozoic geosynclinal belt (Fig. 2). Mesozoic continental clastic sediments in the Colorado Plateau contain about two-thirds of the uranium resource of the United States. These sediments formed from detritus derived from the Mogollon highland in the southwestern United States where the Precambrian was extensively exposed1-1 (Fig. 2). A genetic relationship may exist between this provenance and the major uranium deposits of the Colorado Plateau. The Pre- cambrian might be equally important in the genesis of uranium deposits whether the most important process in the formation of these deposits was the leaching of low-order intrinsic amounts of uranium from Precam-brian granite or from Mesozoic pyroclastics derived from syntexis of the Precambrian basement rocks.' Precambrian Geochronology of the Southwestern United States The Precambrian geochronology of the southwestern United States is in an early stage of systematic study. Until recently, the only basis of correlation was through inconclusive field relationships. However, with the increased use of isotopic age dating, new data are becoming available for correlating regional and local events. As yet, there is no undisputed evidence of ages greater than 1.8 billion years (by) old in the southwestern United States. However, most geologists who have studied the region agree that volcanism and marine sedimentation of predominately eugeosynclinal facies took place in a northeasterly trending geosyn-cline prior to 1.7 by."' Because of insufficient evidence for a pregeosynclinal continental crust, some researchers believe the geosyncline may have developed on oceanic crust.' However, sediments metamorphosed to 1.7 by-old felsic paragneisses in the Panamint Range, California," and southeastward into southern Nevada are believed to have had a nearby continental provenance. The three Precambrian disturbances that are recognized in the southwestern United States are 1.6 to 1.8 by, about 1.4 by, and about 1.1 by-old (Fig. 3). In addition to plutonism, these disturbances are characterized by predominately lower-grade metamorphism. In this report, lower-grade metamorphic rocks include argillite, phyllite, slate, mica schist, and gneiss with relic sedimentary textures. Higher-grade metamorphic rocks, in this report, are recrystallized beyond megascopic recognition of the original rock type. Principal

Jan 1, 1971

By E. C. Truesdale, R. K. Waring

THE Research Division of The New Jersey Zinc Company (of Pa.) has conducted, over a period of years, numerous tests of the reducibility of various zinc ores and the reactivity of various kinds of coal, using a number of different experimental methods. Most of these tests have involved the reduction of mixtures of ore and coal. In such cases the following simultaneous reactions are believed to be mainly responsible for the production of zinc, as was shown by Bodenstein1 some years ago: ZnO + CO = Zn + CO2[I] C + CO2 = 2CO[2]. Each of these reactions is dependent upon the other for the supply of CO and C02, respectively, and the over-all rate of formation of zinc vapor will be determined by the slower of these two reactions. An analogous pair of reactions sometimes of importance is: ZnO + H2 = Zn + H2O[3] C+ H2O=CO+H2[4] While it is possible to obtain an indication of the relative reducibility of various ores, or of a fine versus a coarse ore, by testing them with a given coal, and while coal reactivities may be measured in a corresponding manner, a more direct determination of relative reaction rates is possible by carrying out the desired reactions, such as I and 2, separately and under reproducible conditions. It is one purpose of this paper to present some of the results that have been obtained by the latter method. C. G. Maier2 discusses the relative rates of reactions I and 2 and concludes that while at relatively low temperatures reaction I is faster than reaction 2, this difference becomes less with increasing temperatures, although at smelting temperatures reaction I is still the faster. He also says (p. 48), "At temperatures . . . between 1100° and 1300°C the zinc oxide reduction reaction is intrinsically more rapid than its physical limitations; that is, it is limited by gas diffusion rates." In the course of numerous reactivity tests involving the separate use of reactions and I and 2, we have obtained data that show by direct experiment, we believe for the first time, the correctness of Maier's statements concerning these reactions. We also include data on the relative rate of reaction 3, involving reduction by hydrogen. Finally, some interesting results obtained by carrying out the reduction of a zinc ore-coal briquet in streaming atmospheres of nitrogen, carbon monoxide and hydrogen, respectively, are presented.*

Jan 1, 1941

By J. E. Hilliard

A procedure is described for determining, from measurements on a section, the moments of any degree n (i.e., the mean value of Dn, where D is a linear dimension) of the size distribution of particles (or grains) in an opaque sarnple. The analysis is applicable to particles of alnzost any shape and to any mixture of shapes. However, if absolute values of the wloments are required, it is necessary to know what shapes are present and the relative frequency of their occurrence. In addition, certain shape-dependent parameters have to be evaluated before the formulas can be used. The measurement required is the distribution of intercept lengths. This can be determined either visually or with an automatic scanning instrument. Corrections me derived for the bias due to instrumental end effects. The proposed analysis has the following advantages over existing ones: 1) Confidence limits are easily estimated for the measured properties or, conversely, the number of counts required to achieve a given accuracy can be determined. 2) The analysis is not restricted to particles of a special shape. 3) The error resulting from any known degree of departure of the actual from the assumed particle shape can be estimated. 4) The computations are simple and, apart from a change in constants, are independent of particle shape. 5) The number of particles per unit volume can be determined by a simple counting procedure. MANY procedures have been described for determining the size distribution of particles from measurements on a section (or plane of polish). They differ from one another in the property measured on the section (radius, intercept length, profile area) and in the method used for the numerical solution of the integral equation relating the property to the particle size distribution. However, all existing analyses share at least two of the following disadvantages. 1) They are limited to a particular shape of particle (usually spherical). 2) It is very difficult to determine how the statistical sampling error is propagated into the computed size distribution. The investigator thus has no means of knowing the reliability of his result and, what is of equal concern, he is unable to estimate how many measurements are required to obtain a result of the required accuracy. 3) It is also difficult to assess the error resulting from any deviation between the actual and assumed particle shape. The foregoing limitations stem from the complex relationship between the particle size distribution and the distribution of the property measured on the section. As will be shown, they can be avoided by defining the size distribution in terms of discrete parameters

Jan 1, 1969

By T. Johnston, B. Cox

The results of oxidation and corrosion experiments on niobium in oxygen and steam at temperatures of 350° to 650°C, and in dilute sulphate solutions at 300°C are presented. The oxidation of niobium in oxygen can be explained in terms of a pre-transition period, which obeys an approximately parabolic rate law, and a post-transition period in which a more rapid linear rate is partially stifled by restriction of the gas flow due to the gvowth of the porous outer film. Due to changes in the porosity of the outer layers the restriction presented by the porous outel. film attains a limiting value. Subsequent oxidation obeys a linear rate law and shows an almost linear dependence of the rate on gas pressure. liltimately a second failure of the protective film may take place leading to a further acceleration in the oxidation rate. In water vapor the oxidation of niobium follows a parabolic rate law and does not show a transition to linear kinetics. The higher oxide, Nba05, was usually absent from the NbO/NbO2 film which was formed. The addition of a small partial pressure of oxygen to the water vapo3, resulted in accelerated oxidation according to the normal kinetics for oxidation in oxygen. The oxygen reacted preferentially with the niobium, and the protective oxide film was reformed when all the oxygen had been consumed. This behavior supports the theory that nucleation of Nb205 on the surface of the protective NbO/NbO2 film is the cause of the accelerated oxidation. After oxidation in steam at high-pressure Nb2Os was found in the protective film. The mode of formation of Nb2O5 under these conditions did not produce a change in kinetics, but was thought to explain the comparatively large dependence on pressure of the oxidation rate. The kinetics of oxidation in oxygenated aqueous solutions at 300°C were similar to those for oxidation in oxygen. A penetrating attack on niobium sheet may be related to the second breakaway observed by some investigators of oxidation in oxygen.

Jan 1, 1963

By D. G. Westlake, U. F. Kocks

WHILE single crystals of most materials with cph lattice structure show essentially unlimited ductility, polycrystalline specimens of the same materials exhibit the entire range of ductilities. A difference between the ductility of single crystals and polycrystals may be associated with the special stress concentrations to be expected, for example, at the intersections of slip bands or twin lamellae with grain boundaries. Whether such stress concentrations prove catastrophic depends on the cleavage strength of the material, the size of the stress concentrations, and the speed with which they are formed. Thus, the ductility may vary in degree from material to material. Another possible reason for differences in ductility between single crystals and polycrystals is that a sufficient number of independent deformation modes must be available to insure compatibility between the macroscopic strains in neighboring grains.''2 This criterion is often taken to be a necessary condition for any polycrystal ductility whatsoever, not as one that determines different degrees of ductility; thus, a material with an insufficient number of independent deformation modes would have to be brittle as a polycrystal. The "sufficient number" is five if every grain is to accommodate arbitrary shape changes ("von Mises criterion "). We should like to argue that fewer than five independent modes may be sufficient to satisfy compatibility conditions; and that the internal stresses set up when the plastic strains are not compatible reach the theoretical fracture stress only after a significant amount of macroscopic strain has taken place which may vary in magnitude from case to case, allowing an influence on the degree of ductility. Experimental evidence for these statements is taken from the following review of the number of independent deformation modes observed in the various cph

Jan 1, 1968