Search Documents

By E. H. Burdick

THE difficulties inherent in table concentration operations as applied to gold, silver, lead and zinc ores, are accentuated in the scheelite mill, which has a flowsheet that is similar in general principles. The narrow "spread" in the specific gravity between scheelite and the usual gangue in which it occurs often makes its clean separation extremely difficult and in some cases impracticable. The problem is further complicated by the extreme friability of the mineral and its inordinate tendency to "slime," particularly where fine grinding is necessary and wet grinding methods are employed. The physical aspect of the occurrence of scheelite in the ores, the kind and character of the rock in which the mineral is present, its hardness, friability and the specific gravity of its constituents, as well as like characteristics of the associated minerals-pyrite, pyrrhotite, sphalerite, and others, all have a bearing on the successful milling of crude ores and the production of a concentrate that is marketable with minimum price penalty or none at all. Most tungsten deposits are considered low grade when the limiting factor of low percentage recovery by gravity methods is borne in mind. The great majority of deposits developed or in process of development carry from 0.4 to 1.0 per cent tungstic oxide. Ore carrying I per cent is considered good grade; 0.7 to 0.8 per cent, fair, and below that figure, low grade. Steady mill feed averaging upward of 1.0 per cent W03 is exceptional. Inasmuch as buying specifications demand a 60 per cent W03 content, the mineral content of the ores as mined must be concentrated to at least that degree. A few companies have constructed chemical plants for the treatment of their complex concentrates and low-grade flotation product, but the smaller operator must rely on table concentration, borrowing the tools and to a large extent the methods of his predecessors in the gold, silver, lead and zinc mills. Whether these are the best tools and methods that can be devised is an open question. Except in rare instances, table concentration, however carefully conducted, does not yield a satisfactory final recovery of the mineral content in headings as indicated by chemical determinations of tungstic oxide content. A saving of 60 to 65 per cent is considered fair, and an average 80 per cent recovery, exceptional. Each scheelite ore body is a separate problem. Details of handling that give best results in one case may not be successfully operative at a property on the same contact zone and but a short distance removed. Supplementary treatment of tailings by flotation may be successful in producing a low-grade concentrate of around 15 per cent WO3, which is adapted to further treatment chemically at a given property and entirely unsuccessful at another. This problem constitutes another of the unanswered questions. The following paragraphs relate solely to the beneficiation of scheelite ores by table concentration and supplementary methods.

Jan 1, 1942

By Peter G. Tregelles, Derek K. Barham

Introduction A successful step towards mechanisation of the collier's work was taken in 1954 when the first Anderton shearer loader was commissioned in Lancashire, and progress was reinforced in 1956 when the first powered supports were installed in Nottinghamshire. By 1970, virtually 100% of the coalfaces in the United Kingdom were mechanised and the industry's productivity had doubled. In 1961 the National Coal Board recognised that the next move towards greater productivity and improved safety would be to automate the longwall system. What was not well enough understood, however, was that the basic prerequisites of automation - reliability and measurement - had not yet been achieved. Consequently, the schemes for automatic longwall faces and for an entirely automated colliery were abandoned at the close of the decade. A review of mining research and development policy, commissioned by the Board in 1974, confirmed that the system of longwall mining had great potential for investment and that the short-term policy of automation must once again be pursued. Since then, aided by advances in computer technology, systems for automating the transport of coal from the face to the coal preparation plant have been successfully instituted. Applications of sub-systems dealing with the conveyor, coal preparation plant, and various items of fixed plant are now at the exploitation stage. In the medium term, a number of key problems have been identified, which will arise once the productivity from the coalfaces has doubled, as it is now expected to do in the next five years. One of the most important of these problems is machine guidance, and considerable research and development work is now being carried out in this area. This paper reviews the work on machine guidance prior to 1974 and explains the programme on which the National Coal Board's Mining Research and Development Establishment is currently working.

Jan 1, 1981

By C. H. Jr. Herty

The results of a study of the open-hearth process from the physicochemical view-point are given. This study includes experimentation in small laboratory furnaces and in standard 100-ton furnaces. The behavior of manganese, carbon, and phosphorus are quantitatively explained. The action of "residual" manganese is discussed with reference to its relation to iron oxide dissolved in the metal. The solubility of CO in steel and its relation to dissolved FeO and carbon is given. The equation for phosphorus elimination has been tested out on a 200-ton furnace and the results are given in the text. THE effect of temperature and slag composition on the elimination of metalloids in the basic open-hearth process has been qualitatively understood since the early days of steel making. The quantitative effect has, however, only recently been brought to attention. The effect of slag composition has received more attention than that of temperature, primarily because the range of finishing temperatures in the basic open-hearth process is small compared to the large variations found in the composition of the slag at different periods during the process, and to the variations occurring with the use of raw materials of different degrees of impurity. The effect of slag composition on the elimination of metalloids has been studied by Styri1 from the thermochemical standpoint. This method is open to serious errors, in that thermochemical data at 2900° F. are very inaccurate and in many cases completely lacking. Feild2 has calculated equilibrium constants from the rate at which the metalloids are eliminated. The effect of slag viscosity on rate of elimination will affect the constants calculated by this method. Whitely,3 Colcough4 and others have used slag compositions as the basis for calculation of constants by which the extent of elimination may be calculated.

Jan 2, 1926

By T. C. Wilson, Gerald Edmunds, W. M. Peirce, E. A. Anderson

Thirty-six elements have been alloyed singly with cartridge brass. Ammonia and mercury stress-cracking tests have been conducted on the as-rolled and recrystallized strip. Ultra high purity cartridge brass has also been tested. Silicon improves stress- cracking behavior. High silicon (I per cent) cartridge brass quenched from high temperature (for example, 800 C.) annealing is exceptionally resistant to ammonia stress cracking. This improvement is not lost by subsequent cold working, but is greatly reduced by subsequent low temperature annealing. Phosphorus, arsenic, barium, cerium, magnesium, tellurium, tin, beryllium, and manganese benefit stress-corrosion resistance under some circumstances, but not others. The other alloying additions tried had no large effect on stress-cracking resistance. None of the elements added accelerated stress cracking. The impurities in commercial brass are not responsible for season cracking.

Jan 1, 1945

By M. R. J. Wyllie, Walter D. Rose

The use of electrical well logs for the quantitative determination of such reservoir parameters as connate water saturation, formation permeability and connate water salinity has recently been attracting the attention of a number of workers1,2,3,4,5. While the theory of the determination of connate water salinity from the self potential S.P. log has received rather detailed treatment, relatively little attention has been paid to the theoretical aspects involved in the quantitative interpretation of resistivity data. It is clear that if electrical well logs can be used for the quantitative evaluation of physical characteristics of reservoir rock, they will provide a valuable tool to supplement cheaply information obtained by more laborious core analysis. In certain cases it is conceivable that the coring program could be considerably curtailed if the electric log could be relied upon to give reasonably accurate quantitative information. It is our object in this paper to examine the theoretical basis of quantitative log interpretation as expressed in such well-established logging concepts as formation factor and cementation factor. It is also our object to investigate the physical aspects of the rela- tionship which is presumed to exist between resistivity index and brine saturation in reservoir rock. In particular, we will endeavor to draw attention to the fact that it is possible to express these logging concepts in terms of capillary pressure-saturation relationships, permeability and tortuosity, parameters which we will consider in this paper to be fundamentally indicative of rock texture. The probability of being able to obtain from log recordings alone the data theoretically essential to permit quantitative log interpretatiou will be examined, and consideration will also be given to the problem of formulating simple semi-empirical relationships for use in the field. THEORETICAL CONSIDERATIONS The concept of formation resistivity factor, or as it is now commonly called, formation factor, appears to have been introduced by G. E. Archie",". Formation resistivity factor as defined by Archie is the resistivity of a rock 100 per cent brine-saturated divided by the resistivity of the brine. This relationship had previously been used by physical chemists and the concept is, for example, implicit in an early treatment by Fricke7 of the conductivity of aqueous slurries. Archie was able to establish the fact that although the relationship between formation factor and porosity did not change too greatly for different rock textures, the relationship between formation factor and permeability was markedly dependent on rock texture. The relationship found by Archie between formation factor and porosity was expanded by H. Guyod8. Archie had suggested that the formation factor, F, could be expressed in terms of the porosity, F, as follows: F =F-m .... (11 where, F = effective porosity fraction of the sand, and, m = an exponent greater than about 1.3. Guyod introduced the term cementation factor for the exponent, m, since it may be qualitatively shown that formation factor for any given porosity tends to increase as the sand becomes more cemented. It would appear that the concept of m as an exponent representing the cementation in a sand is strictly only of qualitative value, since the quantitative estimation of m by means other than the determination of F and F has not been possible. Guyod suggests that m can be estimated from a visual examination of a sample of rock, but this method appears to be both arbitrary and unreliable. It can be said, however, that in intergranular reservoirs of practical interest, the range of m is from about 1.4 to 3.0. A possible explanation for the fact that m is found to lie between these limits will be offered below. The determination of formation factor is an essential preliminary to the

Jan 1, 1950

By David Yob

INTRODUCTION This paper is intended to fulfill three major purposes. The first of these purposes is to narrate the improvements to the ventilation of Northeast Churchrock Mine and the subsequent reduction of the radiation levels. The second major objective is to pass on to persons unfamiliar with the ventilation of radon and radon daughter producing mines some of the most important characteristics of airborne radiation and the control thereof. The third objective is to describe the use of a computerized digital mine ventilation simulation. This description is not only of the usage, but also some of the important methods and techniques involved in the usage. This paper is not intended for the persons with extensive experience in these areas. However, to those persons who are just becoming involved with either ventilation of mines with airborne radiation problems or persons interested in computer simulation, this paper should be of some interest. It is the author's experience that most of the information on either computer simulation or airborne radiation control either assumes an extensive knowledge on the part of the reader, or does not address the direct application of the information contained in these articles. It is for that reason that this paper intends to concentrate on the actual application of the topics covered. INITIAL STATUS In the first quarter of 1980, the author and others became involved with the ventilation effort of the Northeast Churchrock Mine. At this time, this team began an investigation of the mine ventilation with the intent of reperforming a mine pressure survey. During the course of this investigation, it was determined that the ventilation system was inadequate. During this first quarter, the responsibility for ventilation of the mine was transferred to the author and his team. It was determined that the system that was in use was that of the single entry or haulage return type. In this type of system, there is very little direct control of the airflow, and it is not an effective type of ventilation for mines that experience problems due to airborne radiation. In a single entry, or haulage return, system there is no separate return system provided. In the system, as we found it, the only source of intake air to the ore level working areas was from the track level. This intake air was forced into the ore level, or stope level, via bulkhead fans installed on raises from the track. This air, after being used in the working areas, was then allowed to find its own way back to the exhausting vent holes. There was essentially no control of this air from the bulkhead fan discharge to the vent hole. The only control used was by the sizing of the fans on the raises. The main portion of this air used the haulage and access drifting for return. Due to the large horsepower used in these bulkhead fans and the large resistance both between the areas to the vent holes and inadequate intake ducting, the stope level pressure was higher than the track level. This pressure differential caused a severe recirculation between the stope level to the track level. This recirculation also caused a severe pre-contamination problem to the supposedly fresh intake air, making his air nearly unusable for working area ventilation. [ ] It was found at the time our ventilation effort began, that the radiation levels were high enough to make compliance with the four working-level month per year standard impossible. For this reason, we had to spend several months driving costly development drifts to implement a completely different type of ventilation system. Before describing the system that was implemented to solve the problems that were discovered during our initial investigation, some discussion of the characteristics of airborne radiation due to radon and radon daughters is needed. RADON CHARACTERISTICS AND RELATED TECHNIQUES One of the most notable characteristics of radiation contamination caused by radon and radon daughter decay is that once the contamination has entered the airstream, the radiation levels as measured in working levels will continue to rise without any further contamination. This radiation rise will eventually stop

Jan 1, 1982

By S. R. Balajee, I. Iwasaki

The adsorption mechanism of corn starch and its derivatives at mineral-solution interfaces was investigated by the adsorption of cationic starch, unmodified corn starch, British Gum 9084, and anionic starch on quartz and hematite. The adsorption of these starches, which decreases in the order mentioned, is dependent on the balance between the magnitude of the electrostatic interaction and the magnitude of the hydrogen bonding. There exists a critical starch concentration for both optimum flotation and flocculation conditions of iron ores, which corresponds to a point where the starch adsorption reaches a saturation coverage. Flocculation occurs due to the adsorption of starch via electrostatic and hydrogen-bonding forces and by interparticle bridging as a result of the conformation of starch molecules at the interface. The depressant property of starches and starch derivatives in flotation' and their flocculation char: acteristics in clarification and filtration2.3 have long been recognized on a wide variety of ores. The effectiveness of a starch as a depressant for iron minerals has been the subject of much investigation in recent years both in the amine flotation of siliceous gangue and in the anionic flotation of activated silica from iron ores. It has been reported that the depressant activity of starches and dextrins in the cationic flotation of quartz from hematite increases with molecular weight, branching, and number of hydroxyl groups, 1 and that the selectivity is affected by changing the configuration of starch molecules and the composition of its polar groups.4 ,5 The manner in which starches are solubilized was shown to exert a significant influence as a depressant in the anionic silica flotation, and a series of articles covering the practical aspects of flotation and flocculation have already been reported.618 Chemical modification of the starch structure, the pulp pH, the calcium ion, and the residual starch concentration were identified as some of the more important variables affecting the flotation behavior. In the flocculation of iron ores, it was noted that most starches flocculated suspensions of hematite in water but did not flocculate similar suspensions of quartz,9 and that an excessive use of starch restabilized the suspensions due presumably to protective action. 6 An admirable application of such an observation to practice may be cited in the selective flocculation and desliming in the anionic silica flotation of iron ores, which resulted in superior metallurgy and lower reagent cost. 10 From detailed adsorption measurements, Schulz'and Cooke4 established that the adsorption of starches and their derivatives depended on the types of minerals and of starches, pH, and electrolytes present. Their adsorption data and the foregoing flotation and flocculation observations suggested that an electrical interaction between starches and charged mineral surfaces might be playing a role in their adsorption process. Adsorption of organic polymers, particularly of synthetic origin, at solid-liquid interfaces has been extensively studied in recent years,' and it is realized that their adsorption mechanism is considerably more complex than that of simple ions or molecules. A polymer molecule possesses a number of functional groups, and the adsorption at a point may restrict the adsorbability of adjacent groups. The mechanism may be further complicated by the conformation of the polymer molecules which may exist as coiled spheres, helices, or extended chains as a result of intramolecular interactions among functional groups as well as intermolecular interactions with solvent molecules. The object of the present investigation was to examine the effect of the chemical modification on the adsorption characteristics of starches and starch products on quartz and hematite at several pH values, so that by correlating this information with flocculation and flotation results, adsorption mechanism of starches on mineral-solution interface may be elucidated. EXPERIMENTAL MATERIALS Quartz: St. Peter sand was screened at 35 mesh and the undersize was scrubbed and deslimed at a Fagergren cell. The deslimed sand was cleaned with 0.1 N hot hydrochloric acid and washed repeatedly with distilled water, For anuscript, measurementsl the -200-mesh fraction of the sand was ground dry in a porcelain mill for 3 hr. The specific surface of the finely ground quartz was

Jan 1, 1970

Open pits and quarries are the major sources of all hard rock tonnages mined today. Normally, ore is fractured from the pit bench face by blasting and then truck-hauled to a primary crusher on the pit rim for conveying to the concentrator; overburden (or waste) is generally truck- hauled from the pit to dump areas. This system of truck haulage of blasted ore and waste accounts for some 25 to 50% of total mining costs in a typical open pit operation and commonly is the largest single cost factor. In an effort to reduce these costs mining companies are continually replacing their older and smaller trucks with larger ones and at the same time are studying conversions to conveyor haulage, since this method of transport seems to offer possibilities of lower costs per ton of material handled. In these studies it seems logical to consider installing these conveyors as close as possible to the mining face for maximum use of conveyors and minimum use of trucks, since a conveyor is much less labor intensive than a trucking system. However, direct loading onto a conveyor near the retreating bench face is impractical because of excessive lump size. Consequently, it is conventional practice to load the blasted rock into trucks at the face for haulage to the crusher. After crushing, the rock is fed onto a conveyor. The closer the crusher is to the mine, or if it is in the mine, the shorter the truck haul and the greater the potential for cost saving. At first appearance, in-pit conveying might seem to be an obvious solution, yet many mining companies have considered such a move while few have implemented it. To determine why, it is necessary to consider the factors influencing such a decision. A conveyor system tends to be capital intensive but can have a lower operating cost per ton than trucks. Trucks, on the other hand, tend to cost less to buy but more to operate; thus, economics tend to favor the conveyor if it can be operated close to capacity and if a sufficiently large tonnage can be passed over the system to mitigate the effect of its high capital cost. In a typical hard-rock, open-pit mine it is necessary for a variety of reasons to mine several faces of both ore and waste at the same time; and any mining system must have sufficient flexibility to permit loading from one face or another at short notice. This makes it impractical to place small mobile crushers and their consequent network of conveyors at each working face. To date no alternative has been found to using trucks for bringing all rock of the same class to some convenient marshalling point from which it may be crushed and conveyed from the pit. Another advantage of trucking when compared to conveying is flexibility. Many mines wish to deliver their shot-rock to different locations, depending on the mineral content. For instance, a typical copper mine may have to simultaneously mine milling ore, leach ore,

Jan 1, 1978

By Len Ramp

CHROMITE deposits in southwestern Oregon occur along definite zones or horizons in sill-like ultramafic intrusions. These horizons are here referred to as ore zones and are distinguishable only by relatively Shin and scattered, discontinuous chromite occurrences. The zones are tabular in shape but are usually folded and faulted by the intensive post-intrusion deformation the ultramafic rocks have undergone. A single zone may contain disseminated, nodular, banded, or pods of massive chromite. The typical chromite deposit is composed of a series of thin lens-shaped bodies that lie along a definite plane and generally show evidence of magmatic flow with their long dimensions aligned in the direction of flow. A body of chromite often pinches down to a narrow wisp only a fraction of an inch thick. This thin streak of chromite may point to or be connected with another body of chromite. In some deposits the orebodies have a definite rake. The depth at which chromite may be found can be predicted by its position in a folded intrusive, provided that adequate structural evidence is available. Although the ore shoots are characteristically discontinuous, there is theoretically no limit to the depth at which chromite may be found. Origin: All the chromite deposits examined in southwestern Oregon are of magmatic origin, that is, the chromite was an original constituent of the peridotite magma and became segregated in varying degree from the magma to form the ore de- posits. Examples of early, intermediate, and late magmatic chromite have been recognized in the area. Crystallization of the principal minerals (olivine, pyroxene, and chromite) was apparently near completion at the time of intrusion of the peridotite magma. The magma acted as a viscous crystal mush stringing out aggregates of pyroxene and chromite in the direction of flow. These streaky accumulations are termed schlieren.

Jan 8, 1957

By S. W. Kennedy, M. Cohen, L. D. Calvert

A high-temperature X-ray diffraction method has been used to study the composition and the kinetics of formation of oxide scales at 800 °C on iron and pure iron-nickel alloys containing 25.6, 75, and 84 pct Ni. This technique has been combined with chemical analysis, and metallographic examination, and determination of weight-gain time curves. The 75 and 84 pct Ni alloys form a three-layer scale consisting of porous NiO next to the metal, a spinel layer, and a -Fe203 on the outside. The 25 pct Ni alloy produces a scale of spinel and Fe,O,, in which, however, traces of FeO and NiO are observed near to the metal. On all the nickel alloys the Fe20, is orieqted with the (107) plane parallel to the surfaces. The exposed surface of the Fe20, is in the form of needles whose axis is perpendicular to the specimen surface. Although the alloys show nonuniform oxidation rates as determined from weight-gain measurements, the X-ray data indicate that the total scale and individml scale layers grow uniformly and parabolically. Deep subscale formation is observed in the 25 pct Ni alloy only. This appeared to be associated with cracking of the scale and penetration of the oxygen along the grain boundaries. ALTHOUGH film formation has been investigated by high-temperature electron-diffraction techniques, for example by Gulbransenl and Hickman,' there have apparently been no investigations of scaling by methods permitting study of the scale during formation at the reaction temperature. Methods involving quenching of scales are based on the working assumption that no significant changes take place on cooling. In general, however, compounds may disproportionate, and the different thermal expansions of constituents may cause disruption of the scale on cooling. In particular, some scales cannot be quenched without spalling. These difficulties are avoided by X-ray diffraction examination at the temperature of formation. High-temperature diffraction procedures also provide a method of determining the kinetics of formation of each phase separately in a multicom-ponent scale. The scaling of binary iron-nickel alloys Containing up to 30 pct Ni at a temperature of 800°C has been studied by Benard and Moreau using cooled specimen~,~ whilst Foley, Druck, and Fryxel14 made an electron-diffraction study of cooled oxide films formed on an iron 42 pci Ni alloy. In the present work the scaling of three iron-nickel alloys containing 25.6, 75, and 84 pct by weight of nickel, at 800°C in oxygen at atmospheric pressure was investigated by X-ray diffraction techniques using a Norelco Geiger-counter diffrac-tometer. The oxidation of iron was investigated for comparison. In addition normal metallographic examinations and chemical and X-ray analyses were made, and weight-gain time curves obtained. EXPERIMENTAL Materials Used—The analyses of the alloys were as follows: Percent by Weight Nickel 25.6 pct 75.4 pct 83.2 pct Aluminum 0.004 None found 0.002 Cobalt — 0.05 0.05 Chromium — — — Silicon — 0.01 None found Carbon All less than 0.05 pct The chemical analysis of the iron was: Al— 0.002 i 0.001 pct, C—0.007 pct, Cr less than 0.001 pct, Cu—0.002 ± 0.001 pct, Mn—0.003 ± 0.001 pct, N—0.0002 pct, 0-0.013 pct, P—less than 0.0002 pct, Pb—not detected, S—0.0017 pct, Si—0.0095 pct, Sn—none detected. This iron was the same as that used to make the alloys and was obtained from the same source-Vacuum Metals Corp. One specimen of pure iron from The British Iron and Steel Research Association was used for preliminary investigation. Specimens were machined to shape from cast rod, polished (the final polish being with 600 Sic paper), degreased in trichlorethylene, washed, and etched. The etching and neutralizing procedure adopted by

Jan 1, 1960

By Harry M. Mikami, Harold A. Heiligman

The term chromite is often used to cover all chrome ores and concentrates which are the designations actually employed by most industrial users and producers. Chromite is, of course, the predominant mineral in chrome ores which are aggregates of chromite and gangue minerals, most commonly magnesian silicates. Most chrome ores now used are petrographically chromitites which is a rock, rather than an individual mineral term. The title of this chapter, following past usage, is meant in the broad sense. Chromite is the only primary commercial source of chromium. This book is intended to deal only with nonmetallic minerals and rocks. Chromite uses are both metallic (ferroalloys) and nonmetallic (refractories and chemicals), but any discussion of mineralogy, geology, and mining is common for all types. A number of the major commercial ores are interchangeable, and their uses are determined by economic considerations. Mineralogy COMPOSITION [Chromite is a term embracing a wide range of chromium-bearing spinel*-group minerals the compositions of which can be expressed as (Mg,Fe2+)0.(Cr,AI,Fe3+ )203.t This can be further generalized to R2+O.R23+03 and the molecular RO: R,03 ratio is generally close to one. The exact composition may be arbitrarily expressed as a solid solution of six end-members, MgAI2O4, MgCr2O4, MgFe2O4 FeCr2O4, FeA12O4, and Fe2+.Fe23+04 with the proportions of each stated or plotted in the six-cornered prism of Johnston and Stevens61 or this scheme may be simplified to comprise only three endmembers making up a composition triangle, Fig 1. [ ] FIG 1-Triaxial composition diagram showing molecular compositions of chromites listed in Table 1. The RO.Fe2O3 corner includes Ti02 norms listed in the table. Note that the high-alumina chromites (1, 2, 3, 9), form a cluster well apart from the high-Cr2O3 chromites. There is a tendency for high-iron chromites to be higher in Fe2O3 + TiO2 but it is not a consistent or systematic relationship. The MgO/RO ratio must also be known to characterize the chromite chemically. Simplest and most convenient method is Thayer's' in which a chromite such as (Mg.65Fe.352+)O.(Cr.40Al.50Fe.103+)203 would be written as (Mge,) Cr eAlo. The molecular pro- portions of ferrous and ferric oxides can be seen at a glance as the divalent and trivalent oxides]

Jan 1, 1960

By B. M. Larsen, W. E. Shenk

THIS paper describes a method of reversal control of the open-hearth furnace that obtains in practice those effects considered below as essential to a completely automatic control, without appreciable interference with the natural rise and fall in temperature of the regenerative portions of the furnace system. Growing out of some studies of radiation pyrometry in open-hearth regenerators, it was developed during 1934-1938, and has been successfully applied to a number of commercial furnaces. The goal of open-hearth furnace operation is the highest rate of production of steel of proper quality consistent with good refractory life and fuel economy. This requires rapid heat transfer from furnace to charge, which in turn is dependent upon heating the furnace refractories to the highest safe operating temperature. The greater the heat input to the melting chamber, the sooner this limiting temperature will be reached, so that control methods in general that are designed to protect against overheating of refractories should help to maintain maximum fuel input and production rate. For the typical open-hearth system, with fixed regenerator capacity and with rate of fuel input usually restricted in its range of variation, our basic assumption is the idea that the only other important variable that is, the time interval between successive reversals-should also be held constant or within a small range. The present reversal control was designed therefore so that, under normal operating conditions, no arbitrary limitation is imposed other than to keep the reversal interval within the optimum time range. However, since a near approach to completely automatic operation involves protection of refractories through the balancing of furnace end temperatures as well as emergency protection against temperature peaks above some upper limit, it was also felt essential to employ, as an integral part of the control unit, a temperature-measuring instrument to register the true temperature of the refractory surfaces at some critical region in the hot ends of the regenerative zones. As the basic elements of the control, we thus have one "maximum" and one "minimum" time relay and a potentiometer recorder-controller, combined with switches and relays to operate as follows: x. Reversal normally occurs within an optimum range limited by the maximum and minimum settings to about 4 to 6 min. variation, but the actual interval usually is less variable and closer to the minimum setting. 2. The margin between minimum and maximum time is utilized, together with a "floating temperature limit" in the potentiometric control instrument, to correct any

Jan 1, 1945

By E. T. Turkdogan, L. S. Darken

Calcium ferrite melts were equilibrated with sulfur and oxygen-bearing gases at temperatures within the range 1290°C to 1620°C. The results show that at oxygen partial pressures below 10-4 atm the sulfide-reaction occurs and at higher oxygen pressures the sulfur dissolves in the melt principally as sulfate ion. It is also observed that when the product increases, sulfate ions are converted to pyrosulfate ions and the results permit the evaluation of the pyrosulfate/sulfate ratio. It is shown that the ratio y CaSO,/rCaO increases with decreasing concentration of calcium oxide in calcium ferrite, silicate and aluminate melts. Indications are that oxy-acids, e.g. silica, alumina and ferric oxide, increase yCaS0,. A few experiments were carried out within the sul-tide range and the results are in accord with those obtained by other investigators on aluminate and silicate melts. BECAUSE of the industrial importance and theoretical interest, many investigators have studied the reactions between molten oxides, silicates or alumi-nates, and gases containing oxygen and sulfur. The early work reviewed by Schenckl and studies made by Bardenheuer and Geller2 indicates that solution of gaseous sulfur in an oxide melt resulted in the replacement of the oxide ions by the sulfide ions. Measurements made by Grant and Chipman3 on the equilibrium partition of sulfur between molten iron and complex silicate melts also demonstrated that, for a given temperature and silicate composition, the distribution of sulfur between slag and metal increased with decreasing oxygen content of the metal. Fincham and Richardson4 studied the effects of temperature and partial pressures of sulfur and oxygen on the solubility of sulfur in simple silicate and alumino-silicate melts. They observed that at oxygen partial pressures below about 10-5 atm sulfur in the gas dissolved in the melt as sulfide ions, replacing an equal number of oxide ions of the melt. At oxygen partial pressures higher than 10-3 atm, sulfur entered the melt as sulfate ions. Similar studies were made by St. Pierre and Chipman5 using calcium ferrite and calcium silico-ferrite melts. The experimental data presented in this paper were obtained in this Laboratory about 10 years ago; this is the first formal presentation although a preliminary report was given previously.6 In each of these experiments, a pure synthetic CaO-Fe2O3 melt in a platinum crucible was equilibrated with a gas mixture (SO2-O2, SO,-air, SO2-CO, or SO2-CO2-CO) at a temperature ranging from 1296°to 1620°C. The experimental technique was essentially the same as that reported by Darken and Gurry,7 the main difference being that the atmosphere in the reaction chamber contained sulfur dioxide together with oxygen, or carbon dioxide-carbon monoxide

Jan 1, 1962

By J. S. Aronofsky, H. J. Ramey

Potentiometric model studies of the five-spot water flood to determine the influence of mobility ratio upon injection or production histories are described. The results suggest a method for the correlation of data from field pilot tests for the estimation of an effective mobility ratio and its effect upon field water floods. The effect of the well spacing-to-well radius ratio upon production histories is presented. A method of accounting for this factor is suggested. The influence of injection (or production) rates and injection and production well pressures upon production histories is shown. The five-spot well pattern was investigated for water-to-oil mobility ratios of 0.1 to infinity. INTRODUCTION It has been well established that mobility ratio has an important effect upon flood patterns.1,2,3,4,5 It should be equally apparent that injection and production histories must also be influenced by mobility ratio. However, none of the articles referred to above mention the importance of being able to predict the effect of well pressures (or injection rates) during the entire time history of a waterflood operation. A complete description of production histories (the terms "injection" and "production" are synonymous for the steady-state model under consideration) would provide values for well pressures and interface positions at any time for a specified injection rate. conversely, if the waterflood problem is specified in terms of a constant injection well pressure, then it would be desirable to know the injection rate and interface positions at any time. This paper describes the results of potentiometric model studies which were used to analyze the influence of mobility ratio on injection or production histories. A method is presented for calculating production histories over a range of ratios of well spacing-to-well radius. The basic method described in this paper to evaluate production histories is to: (1) determine interface position as given in Ref. 1, and (2) measure electrical current and voltage drop for each interface position. It should be mentioned that the current state of knowledge on flood patterns as affected by mobility ratio shows that significant discrepancies exist between the results of various investigators2,3,4,5. It is beyond the scope of this paper to discuss the reasons for such discrepancies. However, the method of determining production histories presented in this paper could be applied to any of the swept-area patterns presented in the literature. All results given in this paper are based on a set of swept areas obtained by the potentiometric method. Potentiometric analyzer technique is adequately described in the literature, but the basic assumptions involved in work of this nature bear repetition. It is assumed that: 1. A distinct oil-water interface exists in the reservoir; only water is mobile in the region behind the interface (water zone) and only oil is mobile in the region ahead of the interface (oil zone). 2. There is a fixed mobility value, (k/µ) w associated

Jan 1, 1957

By J. Mote, P. Ward Flynn, J. E. Dorn

The effect of strain and strain rate on the critical resolved shear stress for prismatic slip in specially oriented single magnesium crystals was determined over a range of temperatures in an effort to identify the thermally activated strain-rate controlling dislocation process. Below about 450°K prismatic slip was preceded by twinning and fracturing. Above 450°K extensive prismatic slip was obtained followed by fracturing. Neither the Peierls&apos; mechanism nor the dislocation intersection mechanism can account for the observations. The data, however, are in good agreement with the dictates of Friedel&apos;s theory for cross slip to the prismatic plane. PREVIOUS investigations on single and polycrys-talline magnesium have resulted in the identification of the mechanisms of plastic deformation summarized in Table I. The-only well-confirmed mechanisms are {0001}, (1010}, (1011) slip plus (1012) twinning. The other twinning modes were only tentatively established and additional investigations are required to further confirm their operation. As noted in Table I, slip in this hexagonal close-packed metal invariably occurs in the direction of greatest atomic density, revealing that the Burger&apos;s vector for-active slip dislocations is always given by b = a/3<1210>. Slip is easily induced on the basal plane, and recent investigations have shown that the strain-rate controlling mechanism at low temperatures is the thermally activated intersection of the glide dislocations with dislocations threading the basal plane. In contrast, very little is known about prismatic slip. It has been reported to be active at points of stress concentration in polycrystals below

Jan 1, 1962

By W. P. Blake

The mining district and the town of Tombstone are situated in Cochise County, Arizona Territory, at the northwest end of the Mule Pass range of mountains, in longitude 110°, and latitude about 31 40&apos; N,, upon the right bank of the San Pedro River, from which the town is distant 9 miles east.. It is also 24 miles south of Benson station on the Southern Pacific Railroad of Arizona, and about 40 miles north of the Mexican line. Its altitude above the sen is 4600 feet. The Dragoon Mountains rise across a valley to the northeast, and the Huachuca Range similarly upon the southwest. The country is open, without timber, and the surface, where the mines are opened, is in general gently rolling, and accessible to wagons by. natural roads. The first locations were made in the pear 1878 by the Scheffelin brothers and Richard Gird, the latter being well known among the pioneers of Arizona as a surveyor and miner, who contributed largely to our knowledge of the geography of the Territory in early days,

Jan 1, 1882

By J. W. Snavely

THE high tension belt conveyor is introducing a new and tremendously expanded era of low cost bulk material handling. High tension belt conveyors are generally those installations involving very long centers, high lifts, or drops, in which the belts are stressed up to their maximum tension values, and further, where the belt construction provides tension capacity far beyond what is possible with conventional belt constructions. With these high tension installations, the magnitude of the forces involved demands careful refinement of accepted design practice in order to achieve optimum balance of all factors. No attempt will be made to evaluate the relative merits of belt conveyor haulage with other means of transportation. For present purposes, it is assumed this has already been done in favor of belt conveyor. Neither will any attempt be made to evaluate the various conveyor belt constructions now available or to balance the advantages of various types of mechanical equipment. It is also assumed that the basic haulage information on which the conveyor design is based is accurate and complete. A sustained maximum, uniform load on the belt at all times must be achieved through proper feed control and the use of adequate surge storage to level the peaks and valleys of any varying demand for the material being handled. General Belt Capacity Considerations The belt conveyor capacity tables published by various belting and conveyor equipment manufacturers vary to a considerable degree, and the ratings given are quite conservative. Of necessity, these published ratings are based on the handling of average materials under average conditions. In applying a high tension belt, all possible capacity from the belt must be obtained in order to hold its width to a minimum and thereby limit the initial cost. Two factors are involved, loading to maximum cross section area and traveling at a maximum practical speed. Belt Loading: Proper treatment of the loading of the belt will result in maximum cross section to the load, and published capacity ratings can be exceeded, sometimes by appreciable margins. On the 10-mile conveyor haul used in the construction of Shasta Dam, California, although the rated capacity of the belt line was 1100 tons per hr, at times the system handled peak loads of 1400 tons per hr, almost 25 pct better than the rated capacity. One of the large coal companies has been able to exceed rated capacity by as much as 50 pct. Loading conditions which must be controlled are: 1. Large lumps must be scalped off and rejected or the load must be primary crushed before being placed on the belt. 2. The material weight per cubic foot must be accurate, must be known for all the materials being handled, and must be known for the complete range of conditions of the individual material being handled. Long centers and high lifts magnify small differences into serious proportions. 3. Uniform feeding to the belt is most important. Various types of feeders are available, which can be used to place a constant predetermined volume of material on the belt, or, where an appreciable range of material weight exists, through electrical control actuated by current demand, to place a predetermined uniform tonnage on the belt. One long slope belt in a coal mine in Pennsylvania is being fed at three separate stations with the controls so arranged that whenever the maximum load is going onto the belt from the first station, the other two stations automatically cut out. Whenever the load from the first station drops back, the other two stations again automatically cut in. 4. Careful design of the chutes and skirts is necessary to get the load centered on the belt with a minimum of free margin along each edge. Some free margin at the edge of the belt is necessary to prevent spillage, but if the load can be kept accurately centered, this free margin area can be reduced, and more material can be carried on the belt. What can be accomplished in this respect will vary widely, depending on the nature of the material being hauled. The chute and skirt design must also protect the belt. 5. The design of chutes and skirts should also get the load traveling in the same direction and close to belt speed, so that the load comes to rest on the belt as quickly as possible. The design of the chutes and skirts is worthy of careful study, and after a system is put into operation it should be experimented with to get the best results. Belt Speed: High belt speeds should be used in high tension work. Obviously, high belt speeds enable haulage on a narrower belt, reducing initial cost. The major portion of belt wear takes place at the loading point and around the terminal pulleys. The

Jan 1, 1952

By O. G. Kiel, G. W. Swift

The concept of "a continuous succession of steady-states", which has been applied successfully by Aromfsky and Jenkins to obtain a solution for the nonlinear partial differential equation describing the transient Darcy flow of gas through porous media, is demonstrated to be equally valid for transient non-Darcy flow. A mathematical model, which numerically solves the partial differential equation, is used to check the validity of the succession of steady-states solution. Comparison of sand-face pressure histories compelted by the two methods shows excellent agreement. The utility of the succession of steady-states solution in predicting performance of gas wells rests in the fact that no special computation equipment is required. The development of the succession of steady-states solution leads also to a practical method for determining and analyzing field test data. A method for taking gas-well test data under constant-rate conditions is presented. Experimental data obtained in the field by employing the constant-rate method are presented and analyzed in accordance with the succession of steady-states solution. Analysis of data in this fashion is demonstrated to give direct "in situ" information for reservoir permeability, porosity and turbulence or non-Darcy coefficient. INTRODUCTION The economics of gas production are dependent upon the transient behavior of flow within the reservoir. For production from a finite reservoir, the transient flow behavior can be subdivided into two parts. At first, the transient caused by the movement of the pressure "wave" into the reservoir is of importance. Later in the production history, the pressure-wave movement ceases and the second transient stage of material depletion becomes controlling. For reservoirs of relatively high permeability, it can be shown that the pressure wave moves into the reservoir and stabilizes quite rapidly. In the case of relatively impermeable reservoirs, quite the opposite is true. Although it is theoretically possible to compute the production capability of a well from the properties of the reservoir as determined by static tests and core analyses, more reliable information is obtained by conducting flow tests on the well and thereby obtaining some measure of "in situ" formation properties. For gas wells, there are two basic types of tests in existence: the flow-after-flow method,&apos; and the isochronal method.&apos; Both of these techniques are tailored to obtain data that can be analyzed in accordance with the empirical performance equation: In addition, the isochronal method makes provision for the sluggish nature of pressure-wave movement in "tight" formations by requiring pressure build-up between flows and by stipulating that data obtained on successive flows be analyzed at equal elapsed flow times. It can be demonstrated that either test is valid for reservoirs of high permeability. Further, since it has been pointed out that the pressure wave stabilizes rapidly for reservoirs of this type, tests of relatively short duration will give stabilized information on the performance of a well. Further decline of sand-face pressure and/or production rate may be determined by employing material-balance techniques. Cullender&apos; points out that for relatively impermeable reservoirs the flow-after-flow method gives invalid results. (See Appendix C.) If the isochronal method of testing is used, there are two alternatives: (1) the tests must be conducted for a sufficient length of time to obtain stabilized information (which may require months to accomplish); or (2) some method for extrapolating the results of short-term isochronal tests must be employed. The first alternative is impracticable because of manpower, conservation and economic considerations. Recourse to the second alternative requires some assurance regarding the reliability of the extrapolation technique. Poettmann and SchilsonJ present an empirical method for predicting stabilized performance. The present investigation was originally initiated to determine the reliability of this technique. To do this, a mathematical model was developed to simulate the Darcy and non-Darcy flow of gas through porous media. The model consisted of a finite-difference approximation of the nonlinear partial differential equation which was solved on an IBM 7090 computer. Long-term production histories were simulated by the model and compared against predictions obtained from the Poettmann-Schilson method. As the work progressed, it became apparent that a straightforward predictive equation could be developed by utilizing the concept of a succession of steady-states. As a result, the emphasis of the work was redirected to exploit the advantages of the new method.

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947

By Carl A. Zapffe, M. Eleanor Haslem

The present investigation has three principal purposes: 1. To develop a method for measuring hydrogen embrittlement that avoids cer, tain errors complicating previously used methods. 2. To explore in a preliminary way some of the fundamental factors controlling embrittlement. 3. To apply the measurements specifically to stainless grades of steel, whose sensitivity or insensitivity to hydrogen embrittlement has never been clearly defined. Selecting a Test Method Hydrogen embrittlement is a condition of low ductility resulting from excessive absorption of hydrogen by the steel at some period in its history, and may be revealed by almost any test involving cold deformation. Tensile tests, impact tests, and bend tests are commonly used for detecting hydrogen embrittlement; although numerous other tests, such as cold-upsetting or extrusion, could be used. The simplicity of using a wire specimen for cathodic and acid pickling tests, and the especial adaptability of the bend test to wire specimens, led to selection of the bend test for the present research. Bend tests usually have been of three general types: (I) fatigue, (2) reversed bend, and (3) single bend. The first two types, though widely used, are inaccurate because their measurements are counteracted by an aging effect; and the third type has not been developed to its fullest utility. The effect of cold-working in removing hydrogen is well known. During a bend test hydrogen can be observed escaping from the convex side simply by coating the specimen with oil; and any technique employing flexing or reverse bending may therefore have its measurements masked because the mechanical action reduces the embrittlement during the test. This factor is so important that even elastic flexing of a hydrogen-charged wire specimen should be avoided before testing if accurate measurements are desired. Developing a Machine for Measuring Hydrogen Embrittlement As for the single-bend test, its theory is good, and recovery caused by mechanical work is kept to a minimum. With a given degree of hydrogen embrittlement, a specimen will break at a given angle if the bending is applied unidirectionally and uniformly. The radius of the bend must be kept constant; and the rate of bending should be a constant, slow enough to allow reading of the breaking angle, and yet rapid enough to prevent significant recovery from the escape of hydrogen during bending. A simple apparatus (Fig. I) was constructed using a type H Foxboro drive unit A, which is a synchronous motor with a gear-reduction ratio of 600 to I. A cord, fixed at one end to a wooden pulley B on the drive shaft of the motor, follows the pe-

Jan 1, 1947