Search Documents

By D. H. Newland

Certain observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U. S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.' The deposits of Canada are described by L. H. Cole. Several states, including Kansas, Oklahoma, Iowa, Michigan,and New York, have made special surveys of their gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago. Association of Gypsum and Anhydrite The two calcium sulfate compounds, gypsum (CaSO4.2H2O) and anhydrite (CaS04), are the more stable forms of a series which includes at least two other members, so-called half-hydrate (CaSO4.1/2H20) and soluble anhydrite (CaS04). Each of the latter readily takes up water to recrystallize as gypsum and consequently is incapable of existence under ordinary geological conditions; also each can be prepared from gypsum by the application of heat within certain temperatures, the process on which is based the manufacture of commercial plasters. If the temperature limitations are not observed, the result of the calcination process will be insoluble anhydrite which, compared with the soluble form, takes up water very slowly so as to be of no practical use, although actually it is soluble and in time is convertible into gypsum like the other forms.

Jan 1, 1922

By John T. Crawford

Much has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of — 48-mesh material. The percentage of this —48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The tonnage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reasonable cleaning job down to and including +l00 mesh, by far the greater majority stop at or short of the + 48-mesh size. Much of the literature on coal flotation passes by the fred pulp density and size by merely stating that the feed varies from 20 to 30 per cent solids and that the size range is from — 1/4 in. or — 1/8 in. to 0. Small wonder then that some operators with entirely different conditions, and not knowing the machine capacity, throw up their hands in despair when flotation is mentioned. Too much parallel is drawn between flotation methods as applied to ores and as applied to coal, to the detriment of the latter. In the flotation of metalliferous ores the feed pulp density ranges from 20 to 30 per cent solids, depending upon the amount of mineral to be floated and upon the size analysis. Thus where 2 to 5 per cent of the

Jan 1, 1936

By John T. Crawford

Much has been written of late regarding the flotation of coal as a means of reclaiming the valuable portion of the fines encountered in nearly all methods of coal preparation. Whether the process be wet or dry, whether the dust be sent through the entire process or removed prior to the cleaning by some such method as screening or aspiration, one of the final products consists of a considerable proportion of — 48-mesh material. The percentage of this —48-mesh material depends upon the mining method, transportation, storage, and method of preparation. The tonnage of this dust material ranges from 1 to 10 per cent of the total output of the cleaning plants. Four methods of disposal are available for this coal: 1. Disposal with the refuse from the plant. 2. Addition, after being reclaimed from the wash water, or dust collectors, without cleaning to the larger sizes. 3. Separate disposal as a pulverized fuel. 4. Cleaning so that addition to the larger sizes benefits the product as a whole. It is also true that flotation in one form or another is the only known way to effectively clean this material. While some processes do a reasonable cleaning job down to and including +l00 mesh, by far the greater majority stop at or short of the + 48-mesh size. Much of the literature on coal flotation passes by the fred pulp density and size by merely stating that the feed varies from 20 to 30 per cent solids and that the size range is from — 1/4 in. or — 1/8 in. to 0. Small wonder then that some operators with entirely different conditions, and not knowing the machine capacity, throw up their hands in despair when flotation is mentioned. Too much parallel is drawn between flotation methods as applied to ores and as applied to coal, to the detriment of the latter. In the flotation of metalliferous ores the feed pulp density ranges from 20 to 30 per cent solids, depending upon the amount of mineral to be floated and upon the size analysis. Thus where 2 to 5 per cent of the

Jan 1, 1936

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy C. Jarrett

In making gold alloys possessing certain physical properties, such i~nportant factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,' E. M. Wise12 and L. Sterner-Rainer2 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by 1/4 by 3/4-in. ingot. The method of obtaining the melting points and making color determinations was described in a previots paper.4 The Rockwell B scale with the 1/16-in. ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, % by 2 by 0.045 in., is blanked from a skip using a die, and the weight loss per square inch of surface is taken as a means of comparison. The time for this test is 2 1/2 hr. of actual submersion of the test picce in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300" F. for 20 min. and cooled in air. Thc "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1940

By Tracy Jarrett

IN making gold alloys possessing certain physical properties, such important factors as corrosion resistance, color, hardness and melting points must be considered. All of these requirements depend directly upon the composition. It is possible to obtain the same colored gold alloy by using different compositions, but in doing so one may bring in some undesirable property. Other investigations have been carried on in this field by F. E. Carter,1 E. M. Wise,2 and L. Sterner-Rainer.3 To make a complete study of the effect of composition upon these properties, a systematic investigation was carried on involving a range of copper content from 85 to 65 per cent. Elements such as zinc, silver and nickel were used to replace in part the copper content. The gold content in all the alloys remained constant. Only 10-karat gold alloys of those containing 41.6 per cent gold will be considered. All of the alloys were made in an induction furnace. Each alloy was cast in a 3 by ¼ by ¾ -in. ingot. The method of obtaining the melting points and making color determinations was described in a previous paper.4 The Rockwell B scale with the ball and 100-kg. weight was used for all hardness determinations. The submersion of test pieces in concentrated nitric acid is one of the standard corrosion tests used in the optical trade. A test piece in the 50 per cent cold-worked condition, ½ by 2 by 0.043 in., is blanked from a strip using a. die, and the weight, loss per square inch of surface is taken as a means of comparison. The time for this test is 2 ½ hr. of actual sub-mersion of the test piece in the acid. This standard test was applied to all of the 10-karat gold alloys discussed in this paper. The tensile tests were made upon strips of the dimensions shown in Fig. 1. The test pieces after blanking were annealed at 1300° F. for 20 min. and cooled in air. The "drop of the beam" method was used in determining the yield point, as there was a very marked "drop" when the yield point was reached.

Jan 1, 1939

By Thomas A. Hendricks

The object of this paper is to give a brief description of the coals in the different districts of Arkansas and Oklahoma, their present commercial classification, and the need for a scientific classification that shall be more nearly in accord with their physical and chemical properties and shall place them in their proper position in a general scheme of classification. The paper is based on two seasons of field work in the Oklahoma coal field in 1930 and 1931 and on several weeks spent in visiting most of the operating mines in Arkansas in the same years. Most of the productive districts of the Arkansas-Oklahoma coal field lie in an east-west trending belt immediately north of the Ouachita Mountains, but the northwestern districts in Oklahoma trend northward toward Kansas. With the exception of the Muskogee district, where very little coal has been mined, the coal beds of the last-mentioned districts are all younger than those of the districts in the east-west trending belt. Description of the Coal by Districts Lehigh District, Oklahoma (5).1—In the Lehigh district mining has been extensive, but only three or four mines are operating at the present time. Two coal beds of workable thickness, Atoka and Lehigh, are known in this field. The greater part of the mining has been in the Lehigh, or younger bed, and all analyses available for the field have been of that coal. The Lehigh coal is very tough and blocky, the moisture and ash contents are fairly high, 6.5 and 10.7 per cent respectively, the volatile content is 39.5 per cent, fixed carbon 43.4 per cent, B.t.u. value 11,525, and the fuel ratio 1.1 (average 15 analyses). So far as the writer has been able to ascertain, laboratory attempts to coke this coal have been unsuccessful and no attempt has been made to produce coke commercially. Tulsa District, Oklahoma (l).—All commercial mining in the Tulsa district has been by stripping from the Dawson bed, and production has never been very great. The coal is blocky, contains 6.5 per cent moisture, 36.8 per cent volatile matter, 48.4 per cent fixed carbon, and 8.3 per cent

Jan 1, 1932

By E. L. Estabrook

Oil companies operating in foreign countries have made increased use during 1930 of cooperative agreements in prospecting unproven territory and in developing proven territory. A considerable proportion of the existing foreign fields are held under single ownership and have been developed as units. The operating companies seek to maintain this condition by acquiring land in large blocks or by merging smaller concessions under unit operating agreements. Your committee has secured a number of reports on foreign non-competitive operations and a valuable formal paper which deals with the Golden Lane of Mexico.l 0. B. Knight has drawn some valuable comparisons concerning costs of development and ultimate production between a certain competitive area and another noncompetitive area along that strip of rich producing territory. After discussing details of production, numbers of wells and cost of drilling and production, he concludes that the 93,700,000 bbl. of competitive oil will have cost $0.193 per barrel as compared to 85,700,000 bbl. of noncompetitive oil at $0.059 per barrel. The saving of $0.134 per barrel amounts in round figures to $11,500,000, which is 21/2 times the total cost of developing the non-competitive block. The cost for drilling and development of the two areas of 3550 acres which Mr. Knight compares was $18,150,000 under competitive and $4,760,000 under noncompetitive conditions. The estimated ultimate production of the competitive 3550 acres is expected to reach 93,700,000 bbl., or 8,000,000 bbl. above the noncompetitive block. Under ordinary production methods it is to be expected that a noncompetitive area will yield less oil per unit area than will a similar competitive area, because of closer spacing and more rapid extraction in the latter case. The advantage of noncompetitive conditions, in this regard, is that the undivided ownership makes it possible to apply repressuring as a production method fairly early in the life of the field and thus, in the end, to vastly increase the yield. In the particular region described by Mr. Knight, repressuring is not thought to be a factor of

Jan 1, 1931

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By W. T. Ober

the hammering effect acts only to a point 3 in. back from the cutting edge, and the hardening heat extends back only 1 in. from the cutting edge. Then, as a steel is taken from the fire, the grain condition is as shown in Fig. I. After the forging operation has been performed the condition shown by Fig. 2 exists. The heating operation to harden the cutting edge produces the effect shown in Fig. 3. The questions that naturally arise are: Will the cost of the extra heat treatment necessary to change this condition (annealing) be more than the saving that may be effected in the drill steel or will the extra heating be an economical as well as a wise thing to do? Is this condition necessarily detrimental to the maximum service of the drill steel? Can this annealing action be obtained in the hardening heat by heating more of the bit, say at least 5 in., to the hardening temperature but quenching only the end of the bit by a shallow immersion? Short Rock-drill Steels Reclaimed by Welding By W. T. Ober, Lynn, Mass. Experimental tests by the Thompson Company have shown that short lengths of rock-drill steels may be reclaimed by electric butt welding. The drills used in the experiments were hollow drills l1/4-in. in diametcr containing 0.95 per cent. to 1.05 per cent. carbon. The ends to be joined must first be ground off fairly square and the greater part of the rust, scale, etc. removed for 3 or 4 in. back in order to insure good electrical contact with the dies of the welder and countersunk, with an 80° countersink, approximately 1/4 in. The steels are then clamped in the copper dies of the welder, so that a length projects from the inside edge of each pair of dies equivalent to from one-half to three-quarters the diameter of the drill. The drills should also be brought into accurate alignment. The first step is to bring the ends into close proximity and then close the primary circuit of the transformer, slowly bringing the steels together until their ends lightly touch, when they will "flash," that is, minute

Jan 1, 1922

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By V. H. Wilhelm

Drilling activity in California during 1939 decreased approximately 15 per cent from that of the previous year. New reserve discoveries were the lowest in many years, but extensions, development of deeper sands, and reappraisals, indicated enough new potential to more than equal 1939 withdrawals of about 223,644,000 barrels. On June 1 a new uniform method of allocation was adopted, which had the immediate effect of reducing production, so that approximately 6,000,000 bbl. of crude were withdrawn from storage during the year. Market demand averaged 628,845 bbl. per day as compared with a daily production of 612,945 barrels. The rate of drilling was slow during the first five months because of the unfavorable storage situation. Subsequent to the adoption of the new uniform method of allocation on June 1, drilling was speeded up and continued at a rapid rate throughout the remainder of the year. As a result of prospecting, four new fields were discovered and seven fields were measurably extended. All of the new discoveries were made in the San Joaquin Valley. Statistics of production and development arc given in Fig. 1 and Tables 1 to 3. New Discoveries Coalinga-Northeast.—The Amerada Petroleum Corporation discovered a second Eocene shore-line field north of the Coalinga Nose when it brought in well S.P.L. 7-17 in sec. 17-19-16, flowing 4230 bbl. of 32.4" gravity oil and 14,200,000 cu. ft. of gas at a depth of 8237 ft., from the "Gatchell" sand of Eocene age. This field, 2 miles north of the Coalinga Nose field, is considered to be a separate structure because it has a gas cap and a lower water table. The structure is a broad, gentle anticlinal nose probably separated from the southerly Coalinga Nose field by a shallow syncline. Production is sealed updip by the pinching out of oil sands. The average sand thickness is approximately 200 ft., the top 75 ft. containing mainly gas. The sand has an average permeability of 1000 millidarcys and an average porosity of 25 per cent. The productivc area of the field is estimated to be between 1200 and 1500 acres.

Jan 1, 1940

By E. Gaujot

IN connection with the question of coal waste and economy in mining, we would call the attention of those interested to an apparatus invented by M. Dernencourt, Superintendent of the Anzin Division of the Anzin Coal Company, North of France. This apparatus is known in France and Belgium under the name of prop screw jack (vis botte), and has been used with good results in the above-named countries for some years past. M. Ponson gives, in his " Traité de l'exploitation des Mines," a description of it (page 533), but as the description given is old, the work not widely known in this country, and as some valuable improvements have been made since, I thought it might be useful to give a description of it, having seen it in operation in 1867, while in Europe to attend the great Exposition, and on a scientific tour to the mining districts of France, Germany, Belgium, and Italy. The prop screw jack is composed of the following pieces: I. The body or column B, Fig. 4 [Plate (1)], of oak or yellow pine, sawed square, the bark taken off, and any length, proportionate to the vein. The smallest are 10 inches diameter at the base, and 9 inches at the top, the height being from 12 to 15 inches less than the size of the vein. In the axis of this column, and at the top end, is a cylindrical opening or hole, C, 2 3/4 inches diameter, 10 inches deep, for the screw, S. II. Two wrought-iron rings, R R, to strengthen the two extremities of the column ; the rings must be put on hot. III. A cast-iron washer, E, with hole in centre a little larger than the screw, to be put on the top of the column, and on which the nut is to rest; the top side of this washer must be faced on the lathe, also the bottom of the nut, to prevent friction. IV. The screw, S, having a total length of 12 inches and a diameter of 21/2 inches (for very high veins this diameter may be in¬creased to 3 inches), and has on its top a wrought-iron plate, T,

Jan 1, 1873

By Henry M. Howe

The data which are collected in Table 1 show that the ferrite of low-carbon steel and of electrolytic iron, like the network of hypo- and hyper-eutectoid carbon steel, inherits, either absolutely or relatively, the grain size of the mother austenite from which it is born in cooling through the transformation range. This evidence is so abundant and concordant as to cast doubt on Prof. Jeffries'l hypothesis of what might be called reversed inheritance, by which he explains Mr. Ruder's observation2 that a grain in a "slug of pressed pure electrolytic iron powder" was coarser, perhaps 1,500,000p2, aftcr a 3-hr. exposure to 1000" C. than after a 3-hr. exposure to 1250-1300°, when the grain size was about 35,000µ2. His explanation implies a natural tendency of coarser austenite grains to yield finer ferrite ones than spring from finer austenite grains, so that the inheritance is reversed. What seems to me a simpler explanation is that the enormous grains which followed the 1000" heating were not inherited from the mother austenite, but were formed by the process of natal coarsening, by means of which Stead and Carpenter developed grains of this same order of magnitude in this same kind of material, on heating to 950" or to 1000°, the temperature used by Mr. Ruder, provided the exposure was not unduly prolonged, and it does not seem to have been in Mr. Ruder's case. That their coarsening was natal and not through inheritance is shown first by the fact that their grain coarseness was out of all proportion to their relatively low temperatures and short periods, and hence was very far in excess of the grain size which the mother austenite must have had, and second and more cogently by the fact that the shape of these coarsened grains was evidently determined by the temperature distribution which existed during and immediately after the Ar3 transformation, that during the passage from the gamma to the non-gamma state. In discussing this subject, we must remember that coarse ferrite grains, whether those formed in cooling from the molten or those induced by

Jan 1, 1918

IN comparing the living conditions of the worker or peasant of the past with those existing today, his-torians might point out many strange contrasts. From the Doomsday Book we learn that at the time of Wil-liam the Conqueror the 1,375,000 inhabitants of Eng-land and Wales owned less than 1000 horses and 5000 oxen. Even as recently as 1871 when England and Wales had a population of 31,845.000, the total number of horses in the country was estimated at 1,110,000. Compare the necessary drudgery of labor in those days with conditions in Canada today where a population of less than ten million people own 3,500,000 horses. Re-member that there is also a turbine installation in` this country of more than four million horse-power, besides steam boilers and locomotive and automobile engines which reduce the traction and hand labor of the farm and factory. Frequently, poetic license has glossed over the poverty and hardship of the common people in the "good old days," and the imagination has created an idyllic world, far from being justified by the condi-tions which actually prevailed. Simon Patten's de-scription of the Middle Ages as "A Thousand Years Without an Ice Box" came nearer portraying the true situation. No one is likely to forget that the discovery of America was an incident in Europe's attempt to find a short route to the Indies, but the fact is usually for-gotten that the summer diet in Europe in 1400-an ice-less age-was such that spices were more precious than gold. Though the glamor of the Indies may never sur-round the modern refrigerator, certainly the modern housewife is likely 'to feel that the applied art called "cookery? may attain to higher levels with the assist-ance-6f such an adjunct. Those who have spoken slightingly of the uniformity of the modern apartment and have eulogized some of the exceptional hand-made furniture which has been bequeathed by former generations, have failed to com-pare modern house furnishings with those in the typical peasant's hovel. Machine-made furniture, though with-out particularly good lines, contrasts quite favorably with the pile of rags in the corner, and the poorest gas or oil stove is better than an open fire on a dirt floor. The scientist's application of the theories of physics, chemistry, biology and mathematics .to practical prob-lems has brought about a series of kaleidoscopic trans-formations in agriculture, industry and commerce. Large scale production, improved means of communica-tion and the prevailing higher standard of living are terms which imply a very human meaning when in-terpreted as actual changes in individual living. Though the student and the teacher may deprecate the influence of commercialism upon science, humanity as a whole has received great benefits from the close relationship which has developed between science and industry, and industry in turn has done much for science through the building and endowment of laboratories and by supply-ing funds to maintain research workers.

Jan 11, 1927

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

By W. H. Echols

An oil-emulsion mud, consisting of a mixture of oil-base mud and bentonitic water-base mud, has been used experimentally in drilling 8 of the 35 wells in the Sivells Bend field, Cooke County, Texas. Experience indicates the oil-emulsion mud can be controlled in much the same manner as a water-base mud, and the "drilling" functions of the two types of mud are comparable. The average water-loss for the oil-emulsion mud was 3.8 cu cm per well. When using oil-emulsion mud to drill the last 2000 ft of 7000 ft wells, the mud costs were approximately 2½ times that of water-base mud. There is nothing to indicate well productivities have been affected through the use of oil-emulsion mud. However, drilling time and bit footages were increased and the holes were maintained more closely to bit guage. The apparent advantages gained through the use of oil-emulsion mud in the Sivells Bend field do not appear to justify the increase in mud costs. Introduction until a comparatively few years ago most of the development of drilling mud was directed toward improving the functions of the mud as related to actual drilling operations. The industry has long recognized that one disadvantage of rotary drilling over cable-tool drilling is the possibility of injury to producing zones through the blocking effect resulting from the infiltration of water or mud into the sands. Recognizing this disadvantage, considerable attention has been diverted toward the development of muds that will improve the quality of well com-pletions through the reduction or elimination of water into the sands, but without sacrificing too many of their "drilling" functions and at a cost commensurate with the benefits derived from their use. This phase of mud research has already found practical application, for example, in the development of the Rangely field, Colorado, it appears the use of oil-base mud during drilling-in operations will contribute appreciably toward making this exploitation more profitable. Much of the discussion to follow will be better understood if a brief sketch of the Sivells Bend field is given. The Sivells Bend field, discovered by The Texas Co. in 1944 and still in the process of development, is in a large bend on the Texas side of the Red River about 85 miles north of Dallas. Geologically, the structure is an unsymmetrical anticline, with faulting having contributed to its development. The productive sands are of the Strawn series of Pennsylvanian age, the sands being lenticular in character and varying considerably in development from well to well. At Present there are 35 producing wells in the field, producing from seven different sand lenses. The productive sand lenses vary from 15 to 50 ft in thickness and the individual sands have average permeabilities of from 75 to 375 md. The presently productive sands are encountered at depths of from 6300 to 7300 ft, but testing has indicated that commercial production might be obtained from other sands as high as 5200 ft. Histories of older Strawn

Jan 1, 1948

By Lane Mitchell

A ceramic product or processed material is a solid composed of materials which have been subjected to heat above 875°F. The raw materials, which are blended together (or in some cases used singly), are selected and utilized for various reasons such as ease of fabrication, aid to processing, to yield desired properties after processing, lack or controllable degree of toxicity or hazard, availability, cost, and perhaps other considerations. Almost all solid inorganic, some organic, and some liquid and gaseous materials have the potential to be used individually in some ceramic product. There are several fundamental functions to be fulfilled in every ceramic product and a number of secondary functions are desirable in specified products. These functions are generally met by the most widely occurring minerals and rocks of the earth and their debris. This fact characterizes ceramics as a field utilizing the raw materials most available to man. Of course, specified products utilize synthetics, organics, and rare inorganics to produce desired results. Any solid nonmetallic product processed by subjection to temperature above a red heat may be called a ceramic product. Widely used construction materials and units, domestic utensils and units, industrial parts to facilitate manufacture, technical components, and aesthetic creations are very often of a ceramic nature because of the durability, inertness, hardness, ease of fabrication, cost, and availability of the ingredients. Often, organics or metals cannot meet desired specifications for some of these products. The rocks and minerals and mineral debris of the earth are largely siliceous. Oxygen and silicon comprise roughly 75% of the earth's crust with aluminum, iron, calcium, and the alkalies following in abundance. Silica ( SiO, ) and silicates can be melted to form glasses. Alumina (A1,0,), present in a mineral com- pound, gives greater durability, hardness, and strength, but lessens the glass-forming property. Iron, calcium, and the other alkalies flux silica and reduce melting points. Thus, sand, which is generally almost pure SiO,, and clay, which is generally hydrated alumina silicate, are the most widely used of all ceramic raw materials-principally because of the glass-forming propensities of silicates. In ceramic formulations, clay is generally a refractory filler or skeletal material, having in the raw state a plasticity derived from its colloidal grain size and its water-loving nature. On the other hand, silica sand is a glass former or nonplastic filler. Clay and silica sand in pure forms are quite refractory, i.e., not easily melted. Clay, although siliceous, is less of a glass former than pure silica and is more refractory. Natural contaminants, such as iron oxide or limestone, adulterate many clays and some sands. These contaminants act as fluxes and reduce the fusion points of the mineral or blends. Glass is made from silica sand by fluxing the sand with strong bases, usually soda ash and limestone. Red building bricks are hard and durable because the sand and clay have been partially fused with help of natural iron oxide serving as a flux. The iron oxide per- forms a dual function, serving as a pigment as well as a flux. In a blend of clay and sand and iron oxide, the sand is more susceptible to fusion than is the clay. Although silica sand and clay are the most widely used raw materials in most ceramic products, many other minerals, and some non- minerals are utilized in products where these materials can produce or aid in achieving desired results. Limestone and dolomite, feldspars, pigmentary minerals, refractory oxides or carbides, and special property producers can

Jan 1, 1975

By J. W. Edington

THE Hopkinson bar has become a popular technique for the measurement of the mechanical properties of materials deformed at high strain rate. Maximum use of the equipment is made in the arrangement first used by Kolskyl in which a short compression specimen is sandwiched between two pressure bars and is loaded by a single pulse travelling through the system. The pressure bars are used both to apply the load to the specimen and as transducers to obtain continuous strain-time histories of three pulses, incident on, reflected, and transmitted by the specimen. The data measured by the pressure bars can be analyzed in terms of the stress/strain behavior of the specimen.2'3 However, one of the assumptions of the analysis of the observed pulses is that the total stress and total strain do not vary significantly from point to point within the specimen at any given instant during the deformation process. Although this assumption is generally justified for very short disc-like specimens2 the situation is uncertain for larger specimens. For example, at small plastic strains (-0.01) Hauser et al.2 have some evidence of small flucations in the total stress within the crystal during deformation, even in relatively short aluminum specimens. In addition, Karnes4 has shown that the plastic strain, and by inference strain rate, is different at each end of a compression specimen tested in a Hopkinson bar, although the length of the specimen was not specified. Recently, the mechanical properties and the dislocation substructure have been investigated in single crystals of columbium5 (length 0.25 in., diam 0.19 in.), and copper6 (length 0.5 in., diam 0.5 in.) deformed at high strain rates. As part of this research program the assumption that the plastic strain is constant throughout the specimen has been checked by measuring the total dislocation density as a function of position in the specimen. Compression specimens of the same orientations and dimensions were tested as described previously5,6 sing a split Hopkinson bar. Since any discontinuity in strain distribution is most likely to arise during the initial stages of deformation the investigation was performed on specimens deformed to plastic shear strains of 0.054 (copper) at a strain rate 1.2 x l03 sec-1, and 0.06 (columbium) at a strain rate 1.5 X l03 sec-1. The orientation of the single crystals is shown in Figs. 1 and 3. Thin foils were taken parallel to the most highly stressed slip plane, i.e., (111) in copper and (011) in columbium, using conventional disc techniques. The dislocation densities were measured using first order reflections with compensation for invisible dislocations.5'6 In the copper single crystals the discs were randomly distributed throughout the cross section of the specimen. However, the dislocation density obtained from each disc was plotted vs the disc positions relative to the ends of the specimen. The results for the copper specimens are shown in Fig. 1. Clearly the dislocation density is constant throughout the main portion of specimen within the experimental error. The error bars on the dislocation densities correspond to a shear strain variation of 0.015 on the basis of previous measurements% ± of the rate of increase of dislocation density with strain in copper single crystals of the same geometry. Thus within this experimental error the plastic strain can be concluded to be constant within the specimen and the assumptions used in the analysis of the stress/time curves are therefore reasonably valid. The higher measured dslocation density near the impact end and the lower dislocation density at the bar end of the copper specimen is in agreement with the results of Karnes4 who showed that this strain/time curve rose to a maximum more rapidly at the impact end compared with the bar end. Hauser et al.2 have also pointed out that at small plastic strains (-0.01) the strain at the impact end of the specimen may be greater than that at the bar end. Thin foils taken from different points within the columbium single crystals demonstrated that the dislocation density could vary significantly within the specimen, see Fig. 2. Large areas of some thin foils up to 30 µ sq contained very few dislocations, see Fig. 2(a). However, in other parts of the compression specimen dislocation configurations like those shown in Fig. 2(b) existed over large areas (-30 µ sq). As a result, when the average dislocation density in a thin foil is plotted as a function of the position of the thin foil relative to the ends of the specimen, considerable scatter is observed, see Fig. 3. In this material then, the local dislocation density, and consequently the

Jan 1, 1970

By Peter T. Luckie, Harold L. Lovell, E. R. Palowitch, A. W. Deurbrouck, James K. Kindig

PART 1: DENSE MEDIUM SEPARATION by E. R. PALOWITCH and A. W. DEURBROUK INTRODUCTION During 1965, 64.9 percent of the 512 million tons of bituminous coal and lignite produced was cleaned mechanically, of which 95 million tons was cleaned by dense medium processes.l The percentage of bituminous coal and lignite cleaned mechanically by dense medium processes rose from 7.0 to 28.5 percent from 1938 to 1965. Dense medium separations include those coal preparation processes which clean raw coal by immersing it in a fluid having a density intermediate between clean coal and reject. As there is a general correlation between ash content and specific gravity, it is possible to achieve the required degree of removal of ash-forming impurities from a raw coal by regulating the specific gravity of the separating fluid. Dense medium processes offer the following advantages over other coal cleaning processes : 1. Ability to make sharp separations at any specific gravity within the range normally required even in the presence of high percentages of the feed in the range of e 0.1 specific gravity units. 2. Ability to maintain a separating gravity that can be controlled with ±0.005 specific gravity units. 3. Ability to handle a wide range of sizes (up to 14 inches). 4. Relatively low capital and operating costs when considered in terms of high capacity and small space requirements. 5. Ability to change specific gravity of separation to meet varying market requirements. 6. Ability to handle fluctuations in feed both in terms of quantity and quality. HISTORY Sir Henry Bessemer patented the first dense medium process in 1858. Solutions of the chlorides of iron, manganese, barium and calcium were proposed as separating liquids; the separation was made in a cone-shaped separator. One large-scale plant using calcium chloride was erected in Germany but soon was abandoned. The Chance process, using a mixture of sand and water, was first

Jan 1, 1968