Search Documents

Large deposits of manganiferous iron ores, representing several million tons of metallic manganese, occur in the United States. The Minnesota deposits of such ore are of outstanding importance because of their size, state of development, ease of mining and proximity to the Great Lakes, which permits water transportation to steel centers. In view of the fact that our steel industry requires large quantities of manganese, for which no satisfactory substitute has been found, and because our reserves of ferro-grade ore are comparatively small, the development of methods that will make our large deposits of manganiferous iron ores available as a source of ferromanganese is an important problem. Realizing the importance of this problem, some years ago the North Central Station of the U. S. Bureau of Mines and the Minnesota School of Mines Experiment Station undertook jointly the development of methods for recovering the .manganese content of manganiferous iron ores in a form suitable for the production of ferromanganese, the 80 per cent. alloy indispensable in producing steel. Two types of manganiferous iron ores have been described in previous reports.' The brown ores are higher in iron and lower in manganese than the black ores; the black ores are more siliceous but contain less phosphorus. The utilization of the iron content of the brown ores in the production of steel appears to furnish the best basis for their treatment. The method of attack has been to work out modifications in iron and steel practice so as to recover manganese in the form of slag comparable to ferro-grade ores. The greater part of the experimental work has been conducted with a 6-ton blast furnace and a 1/2-ton basic open hearth. This paper is devoted mainly to open-hearth tests in which high-phosphorus spiegel

Jan 1, 1930

By F. J. Chernosky

Most previous studies of coal flotation utilized chemically pure reagents. Since such reagents are not available in quantity, a study of various wmmercially available reagents as frothers was undertaken. Flotation procedures similar to those used in a large number of commercial coal flotation plants were employed. The reagents used were compared on yield-selectivity-wst basis. The selectivity was found to be relatively constant with yields above 70% but the reagent cost varied greatly. The types of reagents available were compared. In the past, a number of papers have been written on the use of various reagents as coal flotation frothers. For the most part, these have been an attempt to correlate the intrinsic chemical and physical proper- ties of the reagents or reagent groups to the floata-bility of various fine coals. Because of the type or nature of evaluations made, chemically pure reagents were normally used. Generally, these reagents are unavailable in commercial quantities. Therefore, the results obtained with these reagents were usually limited in usefulness to the plant operator or metallurgist. This paper presents the results of a study in which commercially available forms of various reagents were used as flotation frothers. Flotation procedures which would conform in general to those employed in a large number of commercial coal flotation plants were utilized. The objective of the test was to compare these reagents on yield-selectivity-cost basis, that is, 1) the yields obtained, 2) the ash levels obtained and 3) the reagent cost relating to these results. REAGENTS The reagents employed have been grouped into the following chemical classes: 1) aliphatic alcohols, 2) terpines, 3) glycols (synthetic water-soluble

Jan 1, 1963

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07', the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By Walter Miller

DURING the second year of America's active participation in the war the main objectives of the petroleum refining industry were again to provide the four most important product needs for war: 100-octane aviation gasoline, toluene for TNT production, high-quality lubricating oils for the needs of aviation and the armed forces, and petroleum chemicals for synthetic rubber manufacture. All other materials supplied by the petroleum industry took an inferior priority ranking, depending on the degree of essentiality. To accomplish the above objectives the industry initiated and carried on a building program during 1942 and 1943 which will put those two years down in petroleum refining history as the greatest construction years of all time, a record which will hold for decades to come. Led by an estimated total of $900,000,000 going into 100octane and contributory plant investment, it is easy to picture a total of two billion dollars and more going into additional refining-industry plant investment during 1942 and 1943, most of it privately paid for, but a substantial part covered by R.F.C. Government money financing.

Jan 1, 1944

By E. T. Turkdogan

Jan 1, 1962

By John F. McElhiney, Hosseim Kazemi

This chapter is a review of fluid flow and mass trans- port in fractured rocks. The topics include: single-phase and multiple-phase flow theory, formation productivity or injectivity improvement by artificial fracturing, and mass transport associated with fracture acidizing. Possible extension and application of such ideas to in situ mining in fractured rocks are presented.

Jan 1, 1974

By MARSHALL D. DRAPER

THERE are said to be about 150 operating companies in Kotchiu, most of these being small, corresponding in degree to lessees in western mines in the United States. Of the total number there are probably forty large companies having their own smelting plants equipped with one or two furnaces, slag crushing plant and other accessory equipment. A few plants, not more than ten, do custom smelting. There are in all about fifty smelting plants in Kotchiu. With little variation, the equipment and methods are the same. The plant usually consists of two furnaces, one being in operation while the other is being relined 01- re- paired. An adjoining house contains one or more of the large buffalo-drawn Chilean mills for crushing slag. A few houses for the working coolies, with more pretentious ones for the owners, complete the establishment, the whole being surrounded by a compound wall 8 ft. high.

Jan 1, 1931

By L. Adler

Longwall caving, one of the most economical and attractive mining methods, is yet one of the most difficult and hazardous.1 This dualism is inherent in a method which manipulates the mine supports themselves to aid in excavation. The difficulty is further compounded by the lack of an analytical method to predict and control results. This paper is intended to meet this need by providing a first approximation to the mechanics involved. The analysis will be limited to materials which are linear-elastic, homogeneous and isotropic. The rock structure is assumed to consist of beds of uniform thickness with no interbed bonding.2 Consequently, the mine roof can be likened to a beam, in which the action characteristic of longwall caving is the controlled deflection of the barrier supports. This deflection causes load to be intentionally transferred from these barrier props to the working face.3 Two of the requirements of this method, shared in common with other mining methods, are the provision of (1) adequate and (2) safe working space. The third requirement is the one characteristic of longwall caving and is somewhat in conflict with the second; (3) the development of near-failure static loads at the face. Requirement (1) is handled by spacing the barrier props sufficiently far from the working face for efficient operation. Requirement (2) limits the static stresses in the structure to predetermined allowable values. This means that it is not desirable to induce a maximum load on the working face as requirement (3) may imply. Such a condition could produce collapse in the whole structure. It is the purpose of the undercut to limit the depth, and thereby control the failure of the face. Therefore, requirement (3) really means the development of an optimum, not maximum, load which, in conjunction with undercutting, produces failure at the working face, with minimum powder consumption. Stress analysis requires an exact delineation of the structure and loads. The structure will be defined as the immediate roof and its supports. Since the roof is severed at the caving line, the supports reduce to the barrier props and the working face, as shown in Fig. 1. The mechanics of failure within the working face itself are complex and beyond the scope of this study, since the face represents a typical mine invert structure.4 However, this lack can be made good by the judicious collection of field data. The primary load on the structure is its own weight or body load which can be considered uniformly distributed over its upper surface. Additional loading occurs due to interference of overbeds with the structure. Wherever this occurs, the effect can be approximated by a load uniformly distributed on the upper surface of the structure.5 When this interference is intermittent, as with a much thicker overbed, the elastic curve for the overbed is superimposed on that for the structure and the extent of interference noted, as Fig. 2 shows. However, for simplicity, this study will ignore such intermittent loads without impairing the generality of approach. Consequently, the free-body diagram is that of a uniformly loaded cantilever beam with an inter-mediate support, as shown in Fig. 3. For convenience of analysis, the diagram will be divided just to the

Jan 1, 1961

Organization Place Date 1919 American Society of Civil Engineers..: Twin Cities, Minn. June 17-20 American Society of Mechanical Engineers Detroit, Mich. June 17-20 American Institute of Chemical Engineers Boston, Mass. June 18-21 American Drop. Forge Association Pittsburgh, Pa June 19-21 American Institute of Electrical Engineers Lake Placid, N. Y. June 24-27 American Society for Testing Materials Atlantic City, N. J. June 24-27 Society for Prom. of Engng. Education Baltimore, Md. June 25-28 American Chemical Society Philadelpia, Pa. Sept. 2-6 National Assn. of Stationary Engineers Huntington, W. Va. Sept. 8 American Peat Society.. Minneapolis, Minn. Sept. 22-24 American Iron; Steel Electrical Engineers St. Louis, Mo. Sept. 22-26 American Institute of Min. and Met. Engineers, Chicago, Ill. Sept. 22-27

Jan 6, 1919

By R. H. Winn

A method for the selection of the most suitable corrosion inhibitor for a particular system is given. The method involves the evaluation of surface passivity by means of copper ion displacement after the metal surface has been subjected to the corrosive atmosphere. The application of the method to the selection of suitable inhibitors for use in producing wells is described. Correlation with recognized laboratory tests has beet1 found to be good within the limitations of the test. The use of the test to evaluate inhibitor persistencc is described. INTRODUCTION Corrosion as it is associated with the industry shows wide variations in its qualitative as well as its quantitative aspects. This complicates the work of the corrosion engineer. In the past few years the efforts of the corrosion engineer have been further taxed by the large numbers of products being marketed as corrosion inhibitors by various manufacturers. These products are submitted to him together with a limited amount of data to support their use as inhibitors. The data are usually authentic and reliable yet all too often when these products are applied to an actual corrosive system the results are disappointing due to the ineffectiveness of the inhibitor and the corrosive system. The corrosion engineer must select a comparatively limited number of inhibitors for field trial from the large number available. The selection is usually made on the basis of a standardized laboratory test such as that adopted by the National Association of Corrosion Engineers or by field experience in an area; however, testing of this type is discouraging on large numbers of compounds, particularly in view of the specificity of environment. It has been an object of this work to devise a method which will allow the corrosion engineer to select the best inhibitor for a specific environment under field conditions. The test would of necessity be rapid and inexpensive. It would preferably eliminate the need for expensive and delicate instruments. STATEMENT OF THEORY The test as developed makes use of the fact that metal ions will be displaced from solution by metals having a more positive electrode potential. Thus, if an active iron surface is exposed to a solution of a copper salt, free copper will plate spontaneously on the iron surface as it is displaced from the salt solution by iron ions. If the iron surface is passified, as by coating with an insulating-type organic corrosion inhibitor, it is no longer capable of displacing the copper ions due to its own limited ionization. The result will be a change in the amount of copper plated upon exposure to a neutral copper salt solution. In practice it has been found possible to measure the magnitude of the alteration of the cell potential by determining the copper deposited on a standard iron surface under controlled conditions. This means that, as the film builds up, the resulting shift in the electrode potential tends to cause the iron surface to act more like a noble metal, resulting in a reduction in the cell potential to a point that copper will no longer plate spontaneously. Obviously, the salts of other metals such as silver, gold or platinum might be used for this operation; however, copper was selected because of the color difference of the plate, the comparatively low cost of copper salts and the ease of evaluation of the plated copper. Furthermore, its high cell potential provides a substantial driving energy. The determination of the copper is readily done colorimetrically by dissolving it in 5 per cent ammonium hydroxide solution containing 2 per cent potassium per-sulfate. The blue color of the copper ammonic complex ion so developed may be compared with standards prepared by dissolving known quantities of copper powder in the same reagent. In routine screening it is seldom desirable to determine the amount of copper plated. It is usually more important to determine the concentration of inhibitor required to prevent the plating of copper.

By Herbert H. Kellogg

The chemistry of sulfide roasting is analyzed to show those aspects of performance which Thecan be predicted from considerations of thermodynamic equilibrium. It is concluded that equilibrium calculations can serve as a yardstick for prediction of roaster-gas composition and sulfate formation in the calcine for fluid-bed roasting practice. A method of calculation which combines the equilibrium and stoichiometric factors is outlined, and illustrated by an example from the roasting of Cu-Fe sulfides. ON first examination the roasting of sulfides would not seem to be a process to which equilibrium calculations could be applied to yield results of practical value. The burning of sulfides is an ex-tremely spontaneous reaction, excess air is always used to obtain rapid reaction, and in most traditional roaster designs (hearth roasting) the temperature and gas composition vary widely from point to point in the roaster. These are all conditions which promote a non-equilibrium state in the roasting process. However, the introduction of the fluid-bed roaster1 has brought to roasting practice new conditions of operation, so that equilibrium calculations can be used to predict certain limited aspects of practical operation. The fluid bed is characterized by uniformity of temperature, gas composition, and calcine composition from point to point throughout the bed. These relatively uniform properties of the bed make the meaningful calculation of the equilibrium state of certain reactions in roasting possible. It is the purpose of this paper to analyze roasting from an equilibrium viewpoint, to show where the method may be expected to yield valuable information, where it fails, and to outline methods of calculation. Main Roasting Reaction The reaction MS (s) + 3/2 0, = MO (s) + SO, [I] might well be called the main roasting reaction. It adequately accounts for the well known facts that metal sulfide and air are the main reactants, and metal oxide and SO, the main products. Deviations from this simple stoichiometry will be discussed under side reactions. For all metal sulfides, Reaction 1 is strongly exothermic and the equilibrium position is far to the right. Since the reaction is exothermic, the equilibrium shifts in the right-to-left direction as the temperature is raised. However, at all practical roaster temperatures (between 500" and 1200°C), the amount of this shift is small, and the equilibrium position remains far to the right. The main roasting reaction is essentially irreversible, and the application of equilibrium considerations to this reaction will not be! a fruitful field of investigation. A knowledge of the rate of this reaction. although not the proper subject of this paper, is of great importance to the roasting process. Analysis of the factors which influence this rate shows that: 1) The rate will increase rapidly with increased temperature. 2) The rate will be proportional to the partial pressure of oxygen at the surface of the reacting particle. Because of diffusion effects, the partial pressure of oxygen at the particle surface may be considerably less than in the bulk of the roaster gas. For this reason, intimate contact between gas and solid and high relative velocity between gas and solid, such as can be obtained in a fluid bed or flash roaster, will markedly increase the rate of reaction. 3) The rate will be proportional to the surface area of metal sulfide. Therefore, smaller particle size will permit a more rapid rate per unit of weight. To achieve practical rates of roasting the partial pressure of oxygen in the roaster gases must be maintained at a finite level at all times. Even where the gas-solid contact is very good, as in the fluid-bed roaster, the oxygen content of the gas must not be allowed to drop below some limiting value (perhaps 1 pct), or the rate of the main roasting reaction will become too small for practical operation. Side Reactions in the Gas Phase The gas phase during roasting of metallic sulfides contains the elements oxygen, sulfur, nitrogen, by-

Jan 1, 1957

By D. I. Bardos, A. M. Bardos, Paul A. Beck

The approximate effective silicon radii in ternary Laves phase alloys with transition elements and silicon were found to range between 1.16 and 1.21A, i.e., considerably smaller than the atomic radius calculated for elemental silicon. The atomic radii were found to increase with the size of the transition element atoms in the structure. It has been noted by Aronsson1 that silicon in solid solution in iron, cobalt, and nickel has an effective CN 12 atomic radius of approximately 1.20Å, a value very much smaller than the CN 12 radius of 1.34Å derived from the interatomic distances in elemental silicon.7 The unusually short metal-silicon interatomic distances in transition element monosilicides and disilicides have been also pointed out by various investigators.1 A similar tendency was observed by Nevitt in Cr3O type silicides.2 Recent work on Laves phases in ternary systems of silicon with transition elements4"8 suggested that extensive Laves phase fields may occur in such systems.8 It has been pointed out by Laves7 that the MgCu2 and MgZn2 type structures lend themselves particularly well for the determination of the effective radii of the component atoms. In these AB2 phases the B atoms are arranged in close packed straight lines, and their distances are related in a simple manner to the lattice parameters.8 The present work was undertaken in order to find out whether or not the B transition element in such AB2 Laves phases can be replaced to an appreciable extent by silicon. In cases where extensive substitution proves to be possible, the "average atomic radius for the B site" at various silicon contents was to be determined, and the effective atomic radius of silicon calculated by extrapolation to complete replacement of the B component by silicon. The following ternary systems were studied: Ti-Mn-Si, Ti-Fe-Si, V-Co-Si, V-Ni-Si, Nb-Fe-Si, Nb-Co-Si, Ta-Fe-Si, Ta-Co-Si, and Mo-Fe-Si. In all of these alloy systems, the Laves phase solid solutions were found to extend over a considerable range of silicon content. As previously reported,4"8 in the V-Co-Si, V-Ni-Si, and Mo-Fe-Si ternary systems Laves phases do occur, even though there are no corresponding binary Laves phases. In stabilizing the Laves phase, silicon acts as if it were decreasing the effective electron concentration of the alloy.8 A more detailed study of the boundaries of the Laves phases in the V-Co-Si and V-Ni-Si systems has been made and will be published elsewhere. In both cases, the elongated Laves phase fields extend parallel to the B-Si side of the composition triangle, clearly showing that silicon is substituting for cobalt, respectively, nickel over a wide range of compositions. The binary Laves phases NbCo2 and TaCo2 have the cubic MgCu2-type structure. It was found that, in both ternary systems with silicon, again the MgZn2-type hexagonal Laves phase is stabilized and that this phase extends to high-silicon contents. In each ternary system at least three Laves phase alloys of the composition A(B1_xSix)2 were used, x here denoting the fractional substitution of the B-transition element atoms by silicon. The alloys, listed in Table I, were prepared by arc melting in argon. Each specimen was water quenched after a homogenizing anneal of 3 days at 110(FC, except for the Mo-Fe-Si alloys, which were annealed at 1200°C. Metallographic examination showed that most of the homogenized alloys consisted of a single phase, although some had minor amounts of a second phase, as shown in Table I. X-ray diffraction patterns were prepared using an asymmetrical focusing camera of large resolution and Fe Ka radiation. The patterns were indexed, and the lattice parameters of the hexagonal Laves phases were determined from the available diffraction lines of highest indices: (213), (205), and (313). The lat-

Jan 1, 1963

By J. Armanet

THREE MINING colleges are maintained in France; the École Nationale Supérieure des Mines, of Paris; École Nationale Supérieure des Mines, of Saint Etienne; and the École Supérieure de la Metallurgie et des Mines at Nancy. Besides graduates of these schools, a few graduates of the École Centrale des Arts et MIanufactures and of the École Polytechnique are employed as ]nine managers or engineers; however, most of the latter have taken a graduate course at one of the mining schools.

Jan 1, 1939

By C. C. Harris Discussion by B. K. Loveday

B. K. Loveday (National Institute for Metallurgy, Johannesburg, Republic of South Africa) - The paper and subsequent technical note' describing a method of determining the parameters of the three-parameter size-distribution equation developed in the paper were read with much interest. This equation was also used at National Institute for Metallurgy (NIM) to describe size distributions in grinding tests, because it was necessary to have a single equation to describe the size distribution at any time during a test. A graphical method also was used to determine the three parameters, and the use of this method as an alternative to Professor Harris's latest method is discussed here. The three-parameter model can be expressed as follows: Eq. 1 can be rearranged and transformed to Yield a linear reiationship between Y and X (transformed) log

Jan 1, 1970

By C. H. Lieb

ONE astounding fact in the production of petroleum is the comparatively recent realization by producers that flowing production is the cheapest crude produced. About 1910 or even later, operators actually endeavored to get a producing well to pumping as quickly as possible after completion. A well was not really considered to be completed until it was operating on the pump. Remarkable progress has been made since then. It was not until about 1920 that producers began to take a serious interest in pressures and to think a little about proper methods of handling oil wells. Pressure gauges were installed, and records of pressures maintained, which was quite an innovation. Desultory experiments were made with tubing of different sizes, as well as experiments with placing the bottom of the tubing string at different levels in the well. Probably the first important departure from customary procedure was about 1926, during the Seminole development, when gas lift

Jan 1, 1936

By F. X. Meyer

THE United States Smelting Refining and Mining Company maintains an ore-purchasing department for procurement of custom tonnages of milling and smelting ores and concentrates for treatment at its Midvale plant. Arrangements with other companies provide for treatment of Company and custom zinc concentrates. Location of the Midvale plant in the heart of the Western mining country makes it possible to serve shippers from these nine producing states: Arizona, California, Colorado, Idaho, Montana, Nevada, Oregon, Utah, and Washington. Shipments from most of these states travel over main-line railroads, delivery being made at Midvale within a short time after billing of the shipment. Shipments varying in size from a few sacks to carloads can be handled at

Jan 1, 1948

By C. Y. Wen, H. O. HOPMAN

l. INTRODUCTION. IN casting a thermal balance of the heat generated and absorbed in a blast-furnace treating lead-, copper- and similar non-ferrous ores, assumptions have always to be made for the values of the heat of formation of slag. ? Considering that the larger part of the charge introduced into the furnace comes out in the form of slag, the significance becomes apparent of a lack of heat-values for the singulo-silicate, which is the type of slags commonly made. The aim of the present investigation is to supply these heat-values as far as possible with the apparatus and the time available. The heats of formation of the ferrous and manganous bi-silicates have been determined by Le Chatelier; 1 those of some silicates other than iron and manganese by Tschernobaeff:2 finally Richards 3 gives a figure for a copper blast-furnace slag of known composition. The existing data and those resulting from the present investigation are assembled in Table VI. II. MATERIALS USED. The materials used in the experiments were silica, ferrous oxide, and calcium carbonate. Silica.-The silica sold in the market as chemically pure usually contains small amounts of magnesia, lime, and alumina, and is therefore not suited for the work. The pure material was obtained from clear quartz crystals from Arkansas, broken in a diamond mortar and ground in an agate mortar to pass 1 Comptes rendus, vol. cxx., p. 623 (1895); vol. cxxii., p. SO (1896). 2 Revue de Métallurgie, vol. ii., p. 729 (1905); Electrochemical and Metallurgical Industry, vol. iv., No. 2, p. 72 (Feb., 1906). 3 Electrochemical and Metallurgical Industry, vol. v., No. 7, p. 266 furls?, 1907;) ; Metallurgical Calculations, vol. iii.,.pp. 474, 475 (1908).

Jul 1, 1910

By John V. Beall

Never having done it before, it took us all day and until 11 at night to select and pack for a four-day back- pack trip up Lake Chelan last month. When we were through, we couldn't lift our own pack and Sylvia's, OUT spouse's, we barely managed to budge. Nevertheless, the next morning we were at the dock to board the Laldy of the Lake for the 3 ½ -hr boat trip to Lucerne. Our dress and accouterments creating the appearance of a veritable expedition into the wilderness made a sharp contrast with our fellow passengers, a senior citizens tour group from Spokane. We had come out to Seattle for the SME Fall Meeting and were taking advantage of the occasion for a vacation trip back to Lucerne and Holden where we had lived briefly 25-years ago, and a backpack trip up Railroad Creek from Holden to the Glacier Peak country, weather permitting. No matter what you say, weather is important, and this is one of the ingredients that went into making the SME Fall Meeting and Exhibit in Seattle, September 22-24, a thoroughly delightful experience for the 700 plus persons who attended. Seattle is a beautiful city, but with late September sunshine, which we experienced, it is the best. The second ingredient, is a swinging host committee. Under the leadership of Don Anderson and Tom Van Zandt, co-chairmen, and Mrs. Cecilia Reed, Ladies Program, superb hospitality and fine arrangements were blended. Earl Beistline, from Fairbanks, organized a two-day short course on arctic operations which preceded the meeting and drew an attendance of 44. Dick Robbins, in charge of arrangements, provided Masters-at- arms for technical sessions and a presentation of the colors by the U.S. Coast Guard at the Welcoming Luncheon. Eric Cheney's field trips ranged far and wide with events both before and after the meeting. David (Jeff) Kroft, capably managed audio-visual operations with a group of students from the University of Washington. Charles Hochmuth worked long, hard and effectively before and during the meet- ing on finances. Hank Reed, managed an authentic three-ring circus as Entertainment Chairman. His activities covered two cocktail receptions for all registrants and a dinner-dance. Dolph Campbell and Joe Hackbarth provided publicity by press and TV (see p. 37-40). SME's meetings have certain characteristics and possibly not all of these are known to everyone. The first of these is the deliberate involvement of the AIME Section in the area of the meeting. Most trade shows and conventions are run 100% by a professional staff and although SME staff could also do this, it has been our experience that a more friendly and better meeting results when the local members apply their talents. Actually SME only considers a site for a meeting after it has received an invitation from a Section. The knowledge of local conditions which Section committeemen bring to a meeting is of great value.

Jan 1, 1971

By T. V. Philip, Paul A. Beck

IN a previous note1 it was pointed out that the available information suggests a distinct correlation between the occurrence of the CsCl-type ordered structures formed in equi-atomic binary alloys of transition elements and the location of the components in the periodic table. A definite increase in the bond strength between unlike atoms, as compared with that between like atoms, is indicated when, in binary alloys of iron group elements, the other component is changed from chromium to vanadium or tantalum, to titanium. Laves and Wallbaum,2 eported a CsCl-type ordered structure for the stable intermediate phase at the equi-atomic composition in the Ti-Fe system (and also in the Ti-Ru and Ti-Os systems). On the other hand, Tagaya, Nenno, and Nishiyama8 found no ordering of this kind in the body-centered-cubic solid solutions in the Cr-Fe system. It was concluded' that the occurrence of a CsC1-type ordered phase of intermediate stability may be expected in the V-Fe system. Preliminary results were described: suggesting that at least some degree of order does exist in the equi-atomic alloy VFe, annealed at 1200° C and quenched in cold water. Using CrK radiation, at least one weak superlattice line was found in the X-ray diffraction pattern which could be indexed as (100). and which disappeared, as expected, when FeK radiation was used. It was found more recently that the impurity phase (presumably VN), previously giving rise to additional X-ray diffraction lines and thus preventing definite indentification of the (111) superlattice line,' can be eliminated by preparing the alloy by arc melting in a helium atmosphere. The alloy specimen melted in this manner had clean surfaces and showed very littte, if any, nitride phase in the microstructure after annealing in vacuum at 1250°C and quenching. The relative intensity of the (100). superlattice line with CrK radiation was greatly increased and, in addition, a fairly strong (Ill) , superlattice line and even a detectable (210) , super- lattice line was obtained, when the powder produced by filing from the 1250°C annealed and quenched specimen was reannealed in vacuum at 625°C for 1 hr. By using a cellulose acetate film as a filter in front of the photographic film in order to absorb the soft radiation resulting from air fluorescence, the background intensity could be reduced considerably in relation to the intensity of the diffraction lines. All three superlattice lines, (100),, (111)., and (210)a, disappeared, as expected, when a radiation other than CrK, was used.1 For the powder reannealed at 625ºC, the strongest lines of the s pattern also appeared weakly, indicating that during an: nealing at 625°C a small amount of transformation took place from the body-centered-cubic to the u phase. However, since all superlattice lines to be expected in the 0 angle range used were actually very clearly present, it was evident that the high temperature body-centered-cubic phase had transformed into a CsCl-type ordered structure before much s phase could form. Reannealing filings for 1 hr at 700°C resulted in complete transformation into the u phase. After 1 hr at 650°C the transformation into IT was not quite complete, the strongest body-centered-cubic diffraction lines were still present, although fairly weak, and only the (100), super-lattice line was detectable (extremely weak). These findings not only confirm the previous conclusionsL as to the existence of a CsCl-type ordered structure in the Fe-V system, but they also indicate that this metastable ordered structure forms at about 600°C preceding the formation of the stable s phase, while at 1250°C the disordered body-centered-cubic phase is stable. The faint (loo) , super-lattice line previously observed in specimens quenched from 1200°C was probably due to the fact that the quenching of the powder in an evacuated fuse:! quartz capsule was not fast enough to prevent completely the ordering reaction on cooling. The present results conform with the suggestion that the A-B bond, in relation to the A-A and B-B bonds, increases in strength from CrFe to VFe to TiFc. It is, therefore, of interest to compare the measured values of the average atomic diameter for these three alloys with the corresponding average atomic diameters calculated from the atomic radii of the elements concerned. ASSUming A-B contacts

Jan 1, 1958

By S. H. Ward

Since the advent of the first airborne electromagnetic system, it has been evident that such systems were inherently limited to shallow depths of exploration of the orderof 100 to 200 feet. Hence in 1948 the author and his associates commenced a study of the feasibility of applying natural audio frequency magnetic fields to investigation of the electrical properties of the subsurface in order to provide a system capable of overcoming this limitation. This research culminated, in the summer of 1958, in the development of a new airborne prospecting device — AFMAG. This device has detected surface massive sulphide bodies while flown at heights as great as 3000 feet. Hence, by inference, it is deduced that it could find similar sulphide bodies if they were buried 2500 feet below surface and the aircraft flown at 500 feet. Thus a considerable improvement over conventional airborne electro-magnetic systems is obtainable with AFMAG. Airborne exploration in mountainous terrain involving deep valley fill now becomes possible. Examples are presented of the results of actual airborne AFMAG test surveys over known deposits of massive sulphide mineralization. Interpretation of the data is discussed with particular reference to the knowledge of size, dip, depth, depth extent, and conductivity of causative bodies as deduced from the flight records. The possibility of mapping major geologic structures, for both mining and oil exploration purposes, is discussed with the aid of examples of airborne AFMAG data. INTRODUCTION Electrical prospecting with natural audio frequency electromagnetic waves as a source has, within the last three years, become a practical reality. Both airborne and ground survey instruments under the trademark "AFMAG" (for audio frequency magnetics) have been used successfully in the search for conductive mineral deposits. It is the object of this paper to discuss the principles of airborne AFMAG and to illustrate its application by means of examples obtained over known geological situations. WHY AFMAG? In view of the large number of good airborne electromagnetic systems available for purchase or contract surveying, one may well ask, "Why another new system?". Primarily the answer lies in the fact that AFMAG does not suffer from the very limited depth of exploration available with, and inherent in, any conventional airborne electromagnetic system. AFMAG is not conventional insofar as an artificial transmitter is not required. Only a receiving and detecting device is employed. The electromagnetic fields measured are those from millions of electrical discharges in the atmosphere (e.g;..- lightning strokes). Their random distribution in time and space make these fields difficult to employ and it is only with recent advances in the electronics of geophysical instrumentation that this has become possible. A second reason for AFMAG and one of its

Jan 1, 1961