Search Documents

By M. J. Swan, W. C. Foshee, R. R. Klimpel

The large volume of water used in coal preparation plants makes water recycling a necessity. Economical cleaning of dirty water usually requires flocculation with an efficient organic polyelectrolyte. This paper discusses identification of optimum flocculant systems. Supporting laboratory data with on-site tests and full-scale field trails supplies information necessary for matching the polymer to the plant.

Jan 1, 1983

By W. F. Campbell

One of the deepest coal operations today is the Springhill No. 2 mine of Cumberland Railway & Coal Co., subsidiary of Dominion Coal Co. Ltd. Mining is now conducted at a slope distance of 14,000 ft, with 4400 vertical ft of cover. The record of Springhill No. 2 can be said to contain the history of bumps in the Province of Nova Scotia. The Springhill coal field forms part of the Cumberland field of Carboniferous age. There are seven mineable fields in the area, numbered in the order they were discovered. Mining has been carried on in all but the No. 4 and 5 seams, but present operations are confined to the No. 2. Fig. 1 shows a vertical section through the seams. Opened in 1873, No. 2 mine was first worked from parallel slopes driven from the outcrop of No. 2 seam down to the 7700 level. As the mine went deeper, a two-place auxiliary slope was driven from the 6900 level to the present workings. A transfer level at the 7800 connects the main haulage with the auxiliary haulage slope. The No. 2 mine plan is shown in Figs. 2 and 3. The seam is bituminous, averaging 8.5 to 9 ft thick. There is a well defined parting 14 to 16 in. from the roof, and this roof coal is harder than the rest of the seam. Average pitch at the outcrop is 30°; at the 6500 level, 20°; at the 7900 level, 16°; and at the 13,800 level, 10°. Immediate roof and floor strata consist of beds of variable thicknesses of shales, grading to arenaceous shales to shaly sandstones to sandstones. A characteristic of the strata is the appearance and disappearance of sandstone bands, of considerable thickness, over distances of several hundred feet. MINE HISTORY Entrance to No. 2 mine is obtained by three parallel slopes, separated by 100-ft pillars except in the upper portion of the mine where the pillars are smaller. Main haulage levels were originally driven 600 ft apart for room and pillar extraction. A parallel drainage and intake airway was driven below each haulage level and a parallel return airway (counter level) above. Pillars 80 to 100 ft wide separated these two servicing entries from the center haulage level. Inclines up to 700 ft apart were driven off the levels up pitch to the upper levels, and at 40-ft centers level rooms 12 ft wide were driven off each side of the inclines, separated by crosscuts every 50 to 100 ft. The rooms were driven up to 350 ft or until they were holed into the room from the adjoining incline—a plan followed until the level reached its boundary. When the entire area between two levels had been divided into pillars, the pillars were extracted from the boundary back to the slope pillars. As depth of cover increased, mining conditions required larger pillars, and at the 3300 level, where NECESSARY PRECAUTIONS FOR MINING AT DEPTH In Room and Pillar Extraction: 1) Pillars must not be too small. 2) Pillar size must be uniform. 3) Extraction lines must be kept as straight and as uniform as possible. If they are irregular they should be brought back into line slowly. 4) Peninsulas of coal surrounded by gob must be avoided. 5) Pillars should not be disturbed after they have been formed. If it is necessary to increase the width of an opening, stripping or ribbing should be done gradually over a long distance. If increased width of openings is necessary at certain locations and can be anticipated, the openings should be widened during development. 6) Under no conditions should small pillars be left in the gob that would interfere with caving. In Long wall Operations: 1) Pillars formed during development for retreating longwalls should be uniform in size and shape. 2) Pillars should not be split after development, but if pillar splitting does become necessary it should not be carried out within the zone influenced by the working faces. 3) Width of levels should not be increased after the levels have been developed. If it does become necessary to widen a level it must be done gradually over a long distance by stripping or ribbing the coal ribs. 4) Extraction lines should remain uniform. If several walls are worked together—one behind the other—a uniform distance must be maintained between them and the wall faces must be kept as straight as possible. If the walls do get out of line, they must be brought back into line gradually to allow for a gradual change in the stress distribution over the area. 5) Stumps of coal, roof supports, etc. must not be allowed to remain in the gob to interfere with caving. 6) Midwalls should be built as rigidly as possible and properly maintained.

Jan 1, 1959

By W. Hurst

What is entailed here is the extension of the sinzplified material balance formulas to encompass interference between oil fields. As previously reported, the ex-plicitness as so revealed for the cunzulative pressure drop as a function of all factors contributing to its change in the material balance equation, is now transcribed through the inter-conzmunicating aquifer to effect an increased pressure drop on an adjoining field by interference. Such is performed by mathematical analyses and the application of the Laplace transformations. What is accomplished is that the reiteration problems previously associated with interference studies are nullified, since volumetric changes for the fluids in situ are automatically adjusted by the explicitness so expressed, and what pertains to the superposition principle applies only to the impeded water drive upon a su.bject field, which is likewise incorporated in the over-all pressure drop that results. The mathematics treats with the rigorous solution of the problem, as well as with methods easily amenable to numerical interpretation by the practicing engineer. In all cases, however, what is deduced for areal extents, reveal interference between wells when time becomes large that further substantiate the analyses. Probably of equal significance, all variables and for/nation characteristics are accounted for. This applies to the differences in PVT analyses that occur from field to field and the physical parameters associated with the lithology of the reservoirs. The latter is deduced from a rigorous interpretation of the unsteady-state flow problem for sands of different permeabilities in series. Thus, what purports to be a trial-and-error calculation to include variations in sand conditions within the intercommunicating aquifer to define water drive has little importance compared to the designation of such paranzeters at the reservoir to constitute the essential criteria. INTRODUCTION In a recent publication, the reader has been introduced to the simplified material balance formulas,' It has been shown that the complexities formerly associated for identifying and determining reservoir pressure in the material balance relationship can be resolved by treating with the Laplace transformations, the inversion of which reveals pressure as an explicit function of all factors contributing to its change. For an under saturated oil reservoir, this constitutes an integrated effect from the inception of production; and for a saturated oil reservoir, such represents a survey traverse. However, what is most important, for the first time we are able to express the pressure change in a reservoir directly to the oil, gas and water produced, and to the physical parameters of the formation, in the same manner that reservoir pressure has served in the past to define well interference — which opens up this avenue of endeavor for investigating interference between oil fields. The occurrence of interference is by virtue of the juxtaposition of two or more oil reservoirs producing in the same aquifer. Thus, in any one field, the extended production so incurred creates a pressure lowering in the field, as well as in the aquifer, which can now be transcribed by these simplified material balance formulas to the adjoining reservoir to observe the increased pressure change so induced. These effects are retroactive from field to field, to reveal a pressure drop far in excess of normal depletion to evidence the interference pattern that can result. Such is the purpose for the present undertaking — to develop the mathematical physics treating with this phenomenon of interference between oil fields, employing the simplified material balance formulas. Since Ref. 1 often will be referred to in the text, it is identified as "The Simplification", in the same connotation that another paper has been referred to as the "Laplace Trans-formation. However, the amount of material to be covered in these passages is substantial; therefore, the total emphasis will be placed upon developing these fundamental ideas treating with interference rather than attempting to offer work curves, which always can be prepared. For the practical application of these simplified material balance formulas that form the framework of the present development, the reader will find a comprehensive treatment in the Appendix of Ref. 1, illustrating a factual field example. In essence, what is proposed by this presentation is to make available to the practicing engineer a simplified means to treat with interference between oil fields, independent of the complex machine computations that have attended such undertakings in the past. As the problem unfolds, a common pattern will be discernible, whereby the many reiteration processes that previously required computing devices are eliminated.

By R. J. Charles

Previous study of simple impact systems indicated that energy required for fracture and size reduction of brittle materials is greatly dependent on the type of loading that is employed. In this regard it was postulated that fracture and size reduction of a brittle specimen might be accomplished by a high velocity impact at an energy level at which a low velocity impact would leave the specimen relatively undamaged. The finite time required to propagate energy away from the point of loading of an impacted object to other parts of the object and to its supports may permit a concentration of energy at the point of impact if the rate of loading is high. Localizing of energy at the point of impact could quickly initiate fractures that would propagate through the impacted material along with the traveling stress waves. As the cracks form, the initially absorbed strain energy would be released and portions of it travel ahead of the crack tips as stress waves. These secondary stress waves, combined with the initial stress waves derived from the impact, would produce high localized strain conditions in front of the fracture zone. The fracture zone would propagate and the specimen shatter. High rates of loading are brought about by short impact times, in turn obtained by employing high velocity projectiles that are of small mass compared to the impacted object.

Oct 1, 1956

By C. S. Smith, L. W. Kempf, C. S. Taylor

The thermal conductivity of aluminum alloys is of considerable industrial importance. This is particularly true in such applications as internal-combustion engines where one of the principal reasons for the use of these alloys is their relatively higher thermal conductivity. In spite of this, relatively few data are available on this property of aluminum alloys. The reason is quite apparent to anyone concerned with the experimental determination of coefficients of thermal conductivity. This determination, in theory so simple, is extraordinarily difficult if any high degree of precision is desired. Fortunately, some .knowledge of the relationship between thermal and electrical conductivity has permitted the use of the latter physical property in deducing the relative approximate values of the thermal conductivities of metals. This fundamental relationship, first enunciated by Wiedemann and Franz' as applying to metallic elements and later shown by Lorenz2 to be applicable to alloys within a single metallic system, has been of service in the industrial application of metals. The electrical conductivity of metals is easily determined with a high degree of precision. It is, therefore, quite desirable that the relationship between electrical and thermal characteristics be determined with the greatest possible precision. This paper presents data on the electrical and thermal conductivities of a number of aluminum alloys of industrial importance. Literature on Thermal Conductivity of Aluminum Alloys Masumoto3 determined the electrical and thermal conductivities of 18 aluminum alloys. His results indicated a relatively constant relationship between thermal and electrical conductivity.

Jan 1, 1937

By William P. Blake

In another paper I have described in general the close association of zinc-blende and iron pyrites in the ore-deposits of southwest Wis consin. These two minerals generally occur together at the same horizon, a sheet of one being overlain by a sheet of the other; and also the pyrites is disseminated through the blende to such a degree that the latter is rendered comparatively worthless for the produc tion of spelter. Ordinarily the pyrites, which is mostly the trimetric marcasite variety, occurs in about equal quantity with the blende and is separated by hand-culliug and chipping; but there are large de posits where the ores are so closely mixed that they can neither be separated by culling nor by any mechanical method. The specific gravity of the two minerals is so nearly the same that attempts often made to effect even a partial separation by jigging have proved un. successful. The smelters of zinc-ores in the Mississippi valley will not take ores which carry more than 7 per cent. of iron; and it is therefore necessary to cull the massive ('jack" with great care and at consid erable expense, in order to bring it up to the market-standard of purity. The results of trials to effect a separation of blende and pyrites in other regions have been equally unsatisfactory. The literature of this branch of metallurgy abounds in examples. In Wisconsin efforts have been made in the past to " burn " the mixed ores in heaps, in order to soften or destroy the pyrites, and facilitate its separation from the massive blende. The same method has also been resorted to when galenite is mixed through the substance of the blende, for the purpose of disintegrating the ore, so that it could be separated by jigging. The custom was to pile the ore and the fuel together. As might have been expected, the results were far from satisfactory. As is usual in heap-roast ing, some portions of the ore were overheated and decomposed; zinc was lost by volatilization; the galenite in some portions was

Jan 1, 1894

By T. L. McCall

THE late Walter Herd1 in 1929 gave a full description of past and present conditions in No. 2 mine, Springhill, Nova Scotia, developed theories regarding the cause of these bumps and made certain suggestions regarding possible methods of future development. Recapitulating briefly from Mr. Herd's paper, the seam is bituminous coal, averages 9 ft. in thickness and has a well defined parting containing fusain about 14 in. from the roof. This roof coal is somewhat stronger than the rest of the seam and has a tendency to cling to the roof. The pitch of the seam where it is now being worked is about 20°. The first manifestations of bumps began when the room and pillar workings had reached a depth of cover of 1900 ft. and under continuously increasing depth of cover these bumps increased to such an extent, both in number and severity, that in the year 1924 it became apparent that some change in the system of extraction was necessary. After closely studying all the factors involved and benefiting largely by valuable out-side advice obtained by the Provincial Department of Mines of Nova Scotia,2 the system of working was changed from room and pillar to longwall retreating. Mr. Herd's paper described in detail three remarkable bumps in the year 1928 in April, July and October that affected the 5700-ft. and 5900-ft. East levels, the last bump being so severe both in intensity and in extent of damage done that this district was abandoned. The longwall workings to the west of the slope had been stopped in the year 1926 owing to an inbreak of water, coming from the flooded waste of No. 3 seam lying some 400 ft. vertically overhead. This inflow was not excessive, but a large quantity of water being impounded in the old workings it was considered advisable to take the prudent course and not incur the risk of possibly increasing the flow by further working. This district has remained idle ever since.

Jan 1, 1934

The key-note of good writing, as of good manners, is B natural. Sincerity is the first requisite for effective writing. When a man says what he knows or believes, he is likely to be interesting, because each human being possesses an individuality, a point of view, or a range of sympathy that makes him different from his fellows. To say or to write what you do not think, for the mere sake of talking or writing, is a verbal exercise that must be performed with extraordinary skill if it is to be attractive. Affectations are rarely attractive, rarely effective. To be natural is to be yourself, not a poseur; to give the reader the best of yourself, instead of re-warming the baked meats of yesterday. Quotations-which are second-hand thoughts-will serve occasionally when the thing you want to say has been said so well by another that it would be waste of energy to try to say it better; gut, as a rule, the utterance of the writer himself is more interesting than the quotation, because the writer brings something of himself to bear on the subject, and for the moment is more in touch with the reader than any dear departed author. Therefore, say things as best you can in your own way, neither in borrowed words nor in the phraseology that mimics another. Write as if you were speaking to a person whom you desire to persuade or convince. You will then write better than you speak, because, in the first place, you can be more deliberate, and, secondly, you can revise what you have written. Speaking and writing are similar mental acts, with a difference: the difference between eating food raw and eating it cooked. Some kinds of food gain nothing by being cooked; likewise some kinds of utterance are not bettered by being written down first; but most expressions of thought, especially

Jan 1, 1931

By Leslie F. Tedsen, John E. Dorn, Alan E. Flanigan

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By Leslie F. Tedsen, Alan E. Flanigan, John E. Dorn

It is necessary occasionally to use aluminum-alloy sheet where moderately elevated temperatures are encountered. Considerable attention has been directed toward determining the influence of "artificial aging" on the room-temperature properties of the precipitation-hardenable alloys, as testified by numerous company reports and by references I to 4. Investigations on the properties at elevated temperatures are few, however, and have not always covered the range of times and temperatures of greatest interest. The present investigation was instituted to overcome this deficiency. The work was done for the Office of Production Research and Development of the War Production Board, under the supervision of the War Metallurgy Committee, as a part of the "restricted" Project NRC-548. It has been released for publication by the Office of Production Research and Development. AS is well known, the high-strength aluminum alloys achieve their remarkable properties as a result of precipitation-hardening. In production they are subjected to a solution heat-treatment followed by quenching, to retain the supersaturated solid solution. The solution treatment is followed by "aging" (precipitation-hard- ening) either at room temperature or at a suitable elevated temperature. A considerable increase in tensile and compressive yield stresses results from precipitation at room temperature ("natural aging"). Through the elevated-temperature process ("artificial aging") it is possible to obtain values of yield stress considerably higher than those attainable by natural aging. The increase in yield stress is accompanied by a smaller gain in ultimate tensile stress and by a decrease in elongation. During the first stages of artificial aging the yield stress increases steadily until it reaches a maximum value. In this condition the material is said to be "fully aged." Further exposure results in "averaging," attended by a steady decrease in yield stress. In the production of the artificially aged materials, temperatures and times are selected to achieve full aging. The following important characteristics are associated with the process: 1. The higher the temperature, the more rapidly is the fully aged condition attained. :7

Jan 1, 1946

By J. S. Lasater

Resu1ts of experinmental measurernents of heat capacities and thermal conductivities of some typical porous rocks are presented. Measured heat capacities agree closely with va1ues calculated front known chenlical . compositions of the rocks. On the basis of this agreement, heat capacitir.7 of fluid-satttrated rocks were calc~ililted. Therrnal conductivities of the rock samples were measured under varioits conditions of fluid saturation. From these data therrnal dif-fvsivities were calculated. A significant variation of thermal diflusivity with trnlperature is indicated. Knowledge of the thermal characteristics of fluid-bearing porous rocks has become increasingly important with the development of thermal oil-recovery processes. Reliable thermal data for petroleum reservoir rocks are not available and approximate values are generally assumed for reservoir calculations. 'The effects of temperature, pressure and fluid saturation on thermal properties of porous rocks have not been carefully studied. The purpose of the present work was to measure and report the thermal characteristics of some typical porous rocks. A group of eight sedimentary rock samples, including limestone, shale, sandstone and silt-stone, was selected for the study. Properties reported include heat capacities, thermal conductivities and thermal diffusivities. The effect of fluid saturation on these properties was also considered. Determinations of thermal properties require precise measurements which are time consuming and difficult to reduce to a routine basis. Methods have not been developed for measurement of thermal proper-ties under conditions of pressure, temperature, and fluid saturation, which may be encountered in thermal recovery processes. As one approach to these problems, some preliminary work on methods of estimating thermal properties from other more readily measurable characteristics of the rock-fluid system is reported. The samples selected for the studies were oilfield cores from within, or closely associated with oil-productive zones. Descriptions of individual samples are given in Table 1. Clay minerals present in the samples were determined by differential thermal analysis (DTA). Quartz content was estimated from DTA cooling curves. For all but the thermal conductivity tests, a representative 200-gm sample of each core was disaggregated, thoroughly extracted in diox-ane and oven dried at 100°C. The cleaned and dried sample was care- fully split into appropriate portions for the several tests. Chemical analyses of the samples were obtained to permit calculations of heat capacities by methods which are outlined later. Resuits of chenlical analyses are given in Table 2. Heat contents of the test samples were measured by a Runsen-type calorimeter. The heat content of the unknown sample is measured relative to the known heat content of platinum. The apparatus is referred to as a relative error type because of the comparative measurements, and has the advantage of canceling systematic errors. Experimental results are reproducible within 0.5 per cent. A temperature base of 298.16 K is taken for heat content measurements. Measurements were made at five temperatures (260, 440, 620, 800 and 980° F). It was necessary to preheal the sample above the maximum experimental temperature to eliminate volatile constituents. Assuming the weight loss on pre-heat, ing was mostly water, a correction to the observed heat content was made to account for the water originally present in the sample. This latter procedure was followed in the determination of calculated heat contents as will be described later. The apparatus and the method of measure-

By W. E. Keck, W. C. Lowry, G. C. Eggleston

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By G. C. Eggleston, W. E. Keck, W. C. Lowry

The potential iron ores of Michigan can be classified from the stand-point of the predominant impurities into siliceous, sulphurous and phos-pllorous ores. Research on the flotation of each of these classes of ore was carried out in the following manner. The flotative properties of the valuable minerals of iron and of the worthless and deleterious ones were first determined under carefully controlled conditions. This information was then applied to synthetic mixtures of these minerals, which simulated the potential ores. Finally, data obtained during the two foregoing stages of the investigation were used in the flotation beneficiation of samples of the potential ores. Hematite is the most important mineral of iron in each of the above classes of iron ores. This paper deals with a study of that mineral in the very nearly pure state. There are two varieties of the mineral—specular hematite and massive hematite. The latter is the principal variety, but the former is an impor-tant' mineral of iron in some of the potential ores. Because of this condition, flotation research was performed with both varieties. This research consisted essentially of: (I) a survey of the literature on hematite flotation, (2) the preparation of pure massive hematite, (3) the preparation of pure specular hematite, (4) the development of a laboratory procedure and (5) flotation experimentation. For the purpose of this discussion, the results of previous work on the flotative properties of hematite can be summarized as follows: Specular hematite has been readily floated with terpineol and sodium oleate or heptylic acid1. Further, hematite has been likewise floated with a proprietary frother and oleic acid or other soluble oils2. Finally, lead nitrate, copper sulphate, silver nitrate, chromium nitrate, mercuric chloride, ferric

Jan 1, 1939

By Chas Fettke

DURING the summer of 1916, while on a visit to the United States Agricultural Experiment Station at Mayaguez, Porto Rico, the writers were told by D. W. May, the director, that an occurrence of manganese ore had been reported from the mesa southeast of Mayaguez. A visit to the locality showed that the mesa is covered by a mantle of bright red soil resting upon serpentine. Here and there over its surface concretionary masses of limonite have been washed out of this soil. These were FIG. I.-MAYAGUEZ FROM NORTHWEST END OF MESA. apparently mistaken for manganese ore. On account of the similarity of this occurrence to the extensive iron deposits of northeastern Cuba, it was thought that a brief description based upon a two days' reconnaissance survey of the area would be of scientific interest. Mayaguez is on the west coast of Porto Rico, at Mayaguez Bay, which is the third in importance of the harbors of the island. The city itself is about ¾ mile inland on the low-lying plain at the mouth of the

Jan 3, 1918

By J. F. Peters

The term solution loss is discussed and defined. Examples are given showing that solution loss may either have a favorable or unfavorable effect on blast furnace performance. A theory is advanced explaining the contradictions encountered during earlier studies of the problem. MANY papers have been written and numerous theories advanced concerning the chemical reactions in the iron blast furnace. Richards, discussing the utilization of fuel in the blast furnace, said: "All the carbon burnt in the furnace should be first oxidized at the tuyeres to CO and all the reduction of oxides above the tuyeres should be caused by CO, which thus becomes CO,. This dictum is not Gruner's own words, but expresses their sense, and from the point of view of the present discussion, it is the correct principle upon which to obtain the maximum generation of heat in the furnace from a given weight of fuel." Richards also said the cubic feet of wind per pound of coke does not express how efficiently a furnace is running, but it will be shown later where Howland paid much attention to this figure. Richards pointed out a shortcoming of Grun-er's discussion in that Richards claimed there is not enough CO generated in a good working blast furnace to possibly combine with the oxygen of the ore, so some of it must be reduced by solid carbon. Mathesius2 made two important contributions. First, he wrote the direct and indirect reduction equations showing the heats of formation in each case and stressed that the indirect reduction reaction produces heat while direct reduction absorbs heat. Secondly, he substantiated Richards' conclusion that there may be a deficiency of CO gas and that some direct reduction is required, but he pointed out that "direct reduction in the hearth has often been confused with direct reduction in the stack, which more correctly should be termed 'premature combustion'." Then he said that "as this carbon is consumed partly by economical (direct reduction in the hearth) and partly by wasteful reactions in ever varying proportions, it is evident that the relation of this total carbon gasified above the tuyeres to the fuel consumption of a furnace cannot possibly have a direct bearing on the economy of furnace operation. The premature combustion of carbon (CO2+C?2CO) must therefore in all cases be considered a detrimental reaction." Johnson3 discussed this whole problem. Through experience Johnson found that when departure from Gruner's ideal working is considerable, the fuel economy is poor, and when the quantity of blast goes up, the fuel economy goes up in the same proportion. Johnson said that the wind per pound of coke is a measure of fuel economy, which will be shown to be wrong. Howland4 established the fact from operating data that there was no relationship between the coke consumption of a furnace and the percentage of coke burned at the tuyeres. But some of his calculations have led to questionable conclusions, such as "it is practically impossible to obtain low coke consumption unless we keep our wind low." Howland made an important contribution when, in his concluding paragraphs, he reached certain negative decisions as to why one coke works better than another. He said the reason one coke works better than another in a blast furnace is not because: 1—there is any difference in the percentage gasified at the tuyeres, or 2—there is any difference of wind required per pound of coke. Korevaar5 propounded a new theory on combustion which disagrees with Gruner because "as far as we can see, this is sufficient proof for the invalidity of Gruner's ideal, for if it was valid, the Low coke consumption should always be accompanied by a higher percentage of carbon burned at the tuyeres. This not being the case, we must deliberately give up our belief in Gruner's ideal." The part in italics will be proved to be wrong. Martin" contended that there was not enough reducing capacity in the blast furnace unless solution loss occurs. He came to a series of conclusions, such as: 1—The greatest efficiency of the blast furnace may not be attained when the reduction is performed entirely by carbon monoxide as demanded by Gruner's definition of the ideally perfect working of the blast furnace. 2—The so-called solution loss reactions, which should more properly be termed direct reduction reactions, promote furnace efficiency. 3—In modern blast furnace practice, the carbon consumption of the process is determined primarily by the carbon needed for reduction purposes, any thermal deficiency created by the reduction process being balanced in practice by the use of blast heat. From a practical standpoint further discussion of the theory of chemical reactions is of little moment. There is however one phase of the general theory of chemical reactions which is very important and that is the combustion of coke in the blast furnace. The purpose of this paper is to show that the reaction

Jan 1, 1955

By Persifor Frazer

The mines which I am about to describe are all situated in the northern part of the States of Nuevo Leon and Coahuila, Mexico, between the twenty-sixth and twenty-seventh degrees of latitude. They might be grouped, orographically, into four classes: 1. Those in the Sierra de la Ygnana chain; 2. Those in the Sierra de Gomez chain; 3. Those in the Cerro Mercado; 4. Those in the Sierra de San Marcos chain. (See large map.) The first two of these may be further arranged in one geographical district, to which the name, "the Villaldatna. district," may be applied, and the last may be ascribed to the geographical district of " Monclova." Geologically described, the country rock, in which four of the six mines occnr, is a limestone, concerning which a few words will be said further on, to wit.: The Arroyo (gulch), the Montanos and the Pinitos (pines), in the Villaldama district, and La Paloma (the dove), or Iron Mine, in the Monclova district. The San Rafael appears to lie in granite, or a heavy-bedded gneiss, presenting most of the characteristics of the latter, though the contact plane of the limestone is not far off. It is certainly worthy of attention that the ore occurs in that portion of the crystalline rock, which is nearest to the limestone, and it has been thought by some observers to be a true contact vein. It is well known that veins of this character are very often distinguished for constancy and richness. Although the undersigned cannot entirely free himself from the impression that this proximity of different formations has had an important influence in the origin of the part of the vein on which this mine is situated; still he was unable to establish it actually at the contact of the limestone and granite, but rather a short distance within the latter. Two openings of the Riojas vein were respectively in limestone and in rotten whitish granite, but this fact, if established (as by the correspondence of the strike line of the vein in direction with that of a line joining the

Jan 1, 1884

By R. W. Ph. D. Raymond, Anton Filers, O. H. Hahn

THIS paper will treat of such works only as beneficiate ores directly in the mining districts. And when it is said that more than twenty furnaces exist in Utah, about as many in Nevada, five in Montana, and four in Cerro Gordo, Inyo County, California, it is obvious that a business so extended deserves attention. Wide apart as these different works are located, they have nevertheless to deal in nearly every case with the same or very similar circumstances and conditions, so that, with very few exceptions, virtually the same system of smelting is followed in all these establishments. This is the so-called method of reduction and precipitation in blast-furnaces. As the principal reasons for the employment of a blast-furnace process are to be considered : the low percentage of lead in the ores, the high price of the only available fuel, charcoal, and the exorbitant rates demanded for labor. The reasons why the reduction and precipitation process is preferred to a roasting, reduction, and precipitation process are the high prices of labor and materials, and the preponderance of oxidized ores over sulphurets, though in some cases the latter are quite abundant. The weight of these reasons will be better understood when the character of the ores to be treated and the object of the smelting are more minutely stated. The ores are in nearly all cases a preponderating mass of oxidized lead ores, such as cerussite, anglesite, and leadhillite, in which nests and nodules of undecomposed galena occur. Associated with these are : in Eureka, Nevada, arseniate of iron and arsenical pyrites, hydrated oxide of iron, quartz, and calcareous clay ; in Little Cottonwood Canyon and American Fork, Utah, iron oxide, and in some cases a combination of antimony, the nature of which I have not ascertained; also dolomite and quartz in widely varying proportions; in Bingham Canyon, Utah, only quartz and comparatively little oxide of iron, or iron sulphurets; in Cerro Gordo, California, oxide of iron, iron pyrites, antimonial compounds, copper ores, and, as gangue, carbonate of lime and quartz. In Argenta, Montana, occur, besides the above-named lead ores, pyromorphite, and molybdate of lead. The preponderating gangue of the Argenta ores is quartz, and there is here a larger proportion of galena than elsewhere in the West. In most of the localities named, the lead ores themselves contain sufficient silver to render its separation from the ore the main object of the smelting; but in some of the districts, and especially in Montana, the lead ores serve only to furnish the extracting agent for the silver of true quartzose silver ores, which at the same time contain a sufficient percentage of lead to make amalgamation impracticable. They are therefore beneficiated by smelting, although the lead itself has no market value.

Jan 1, 1873

By T. A. Rickard

RICO, in the southwestern corner of Colorado, is one of the productive mining centers of the San Juan region, so-called because its waters drain into the river of that name, which is tributary to the Colorado. The San Juan region includes the counties of Ouray, Hinsdale, San Miguel, Dolores, San Juan and Montezuma. It is traversed by a network of picturesque mountain ranges on whose lofty summits there rests perpetual snow. The region is peculiarly rugged, and, in the early days of its development, tested to the full the hardihood of the adventurers who first explored its can ions 111 search for gold and silver. A prospecting party, guided by Jim Baker, scout and trapper, penetrated in 1861 this part of the territory of Kansas. At that time the country was in the possession of the Ute Indians. In October, 1873, by the Brunot treaty, they ceded to the United States Government the richest mineral-bearing portion of their

Jan 1, 1897

By Evan Just

Throughout history mining operations have, been relatively technical in character and somewhat esoteric. In ancient times mines were places where prisoners of war or criminals were sent, to drag out short lives of hard labor, under conditions ranging from hazardous to lethal. Underground mines were damp and poorly lighted, and workers were often cramped in narrow spaces and tiresome positions. Hard rock was mined by building fires against faces and quenching with water. Combustion products from these fires and from such dim torches as were provided, plus the dampness, made the underground atmospheres quite injurious to health. During the Middle Ages, mining became less penitential and more technical. Because of the desire of sovereigns to foster production from mines, miners enjoyed special privileges as free men. Crude pumping, hoisting, and ventilation systems were introduced (Fig. 9.1). However, mining remained a relatively hardworking, hazardous occupation, separated from the lives and comprehensions of most people. With the Industrial Revolution, steam-powered pumps enabled penetration to greater depths, and the use of power-driven machinery gradually revolutionized productivity. Skill became more important than back-breaking labor. This revolution continues into the present. Mining today uses some of the largest and most complicated machinery in existence and little rock is moved by direct labor. Power drills, explosives, and boring machines penetrate and break hard rock. The modern mine, surface or underground, presents an impressive panoply of drilling, breaking, loading, and transporting equipment, facilities for power transmission, pumping, and ventilation, and expensive, complicated crushing and treatment machinery. Modern technology, machinery, and skilled workmen produce an efficiency that knows no parallel in the raw material field. Mineral substances are extracted and converted into useful forms at costs which are dwarfed by those of providing forest or agricultural products in terms of comparable weights, even though conversion of these last categories is typically much simpler. Capital investment per worker, i.e., mechanization, is greater than in nearly all other industries. Despite these features, and more than average financial risk, the mineral industries perform at modest profit. The popular concept that mines and oil fields are sources of boundless rewards is a myth, sustained by the occasional unusual episode. Before one can start actual production of minerals, he must first acquire a suitable deposit. The process of acquisition will require anything from a rather simple search to a difficult, lengthy, expensive exploration effort. After locating the desired deposit, title must be obtained by denouncement, concession, leasing, or purchase. If the deposit is solid, it can be mined in pits or underground workings. If fluid or easily fusible, it can be produced through wells. If dissolved in lake or seawater, it can be

Jan 1, 1976

By G. S. Cole, G. F. Bolling

A series of Al-Cu alloys has been cast from constant superheat to solidify either with a hot top or with a free liquid/air interface. All the other variables which affect relative fluid motions were kept constant except the imposition of slow rotations m oscillations of the mold. Depending upon the exact circumstances, evi-dence could be found for the nucleation of equiaxed grains from dendrite bits detached from the columnar zone, or from the free surface, or from solid bits induced at pouring; a special experiment showed the solute buildup during ingot solidification and by inference the reality of constitutional supercooling. All methods of grain nucleation are thus supported. When solidification is arranged in a static mold the columnar- to-equiaxed transition occurs by one of these nucleation paths, subject to the natural decay of temperature gradients which promotes nucleation or the survival of nuclei. But when solidification is forced under special fluid flows it may display odd transitions. In one of these the equiaxed zone is synihesized from. dendrite bits detached from the solid/liquid interface. These survive under the concurrent lowering of temperature gradients and eventually cause transition by impeding columnar growth. GRAIN structure control is desired because real experience shows that specific properties are associated with specific cast grain structures. But since control is thus a matter of need and does not require understanding, much of casting remains art. For example, the manipulation of relative fluid motions in simple ingots provides a control of grain structure development,1-4 but theoretical insight is not required in order to broaden its potential applicability. Fortunately, however, once a variable like fluid flow is recognized it can also provide paths toward new insight. New observations using this variable have provided an insight which is curious. All the theories or descriptions of the columnar-to-equiaxed transition (CET) seem to be supported as long as the appropriate experiment is carried out. In order to develop this idea, let us ignore segregation, the chill zone (until a later section of this paper), and the origin and development of the columnar zone.= The details of questioning how equiaxed material forms in a casting may be divided in two. The first part is simply a questioning of the origin for equi-axed grains: are there fresh nuclei from heterogeneous nucleation, or dendrite bits broken off or melted from the columnar zone or elsewhere,6 or other solid bits surviving from the outset of freezing? The second is more complex, a questioning of the CET: does columnar growth slow down and allow the dominance of equiaxed grains, however they are formed, or do equi-axed grains take over and force columnar growth to stop? This "chicken-or-the-egg" second question can be quite useful, especially because it allows us to delineate the ordinary or NATURAL EQUIAXED ZONE and the induced or SYNTHETIC EQUIAXED ZONE. A natural equiaxed zone occurs if solidification proceeds in the absence of disturbances or extraneous forces such as ultrasonics, stirrings, and so forth. Both the CET theory proposed by Winegard and Chal-mers, 7requiring constitutional supercooling, and the CET theory suggested by Chalmers,8 requiring nuclea-tion only on pouring, pertain to the natural equiaxed zone. The best collating evidence to date for both these theories is contained in the work by Biloni and Chal-mers;9,10 the former theory7 is supported by special versions of the unidirectional growth experiment performed by Plaskett and winegardl1 and the latter theory' is supported in detail for the solidification of small ingots. An equiaxed zone can be synthesized when disturbances caused by forced fluid flows2-4 or other artificial means9,10 break off or melt off dendrite tips from an advancing solid/liquid interface,* if (and only if) temperature gradients in the melt are (forcibly) reduced enough to ensure the survival of these bits of dendrites, 2'3 Willful disturbances even so trivial as those produced by rapping a mold might be included here; as will be shown for example, this follows Southin's suggestion that the free liquid/air interface

Jan 1, 1970