Search Documents

By O. W. Ellis

THE writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.1 The copper referred to in his in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal, did not measure up to conductivity FIG. L -INGOT OF OVERPOLEP COPPER. standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the Westinghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 ½ in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of overpoling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By A. W. Griffith, R. G. Beverly, W. A. Millsap

THE Grand Junction Pilot Plant, operated by National Lead Co. Inc., for the U. S. Atomic Energy Commission, is engaged in the amenability testing of orebodies to establish design and cost data for commercial mills and to test new processes for recovery of uranium from ores. Test work was performed to study the effects of several variables on leaching of uranium ores in carbonate solutions. Many of these variables had been investigated in the laboratory, but pilot plant tests were desirable to evaluate their importance in semi-works equipment and to predict optimum operating conditions for future commercial mills. The results of these tests should serve as a guide in selecting the most efficient and economical method of leaching uranium ores amenable to a carbonate process. This article is concerned with a process in which uranium is extracted from the ore by a hot Na2CO3- NaHCO3 solution; the uranium-bearing solution is separated from the solid residue by filtration, and uranium is then precipitated by chemical means.

Jan 9, 1957

By Lawrence K. Jetter, Robert F. Mehl

SOME advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory.? Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selected for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatometric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system-a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation ;2,3,4 there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type-the ideal case which Becker5 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1942

By W. A. Foster

NINETY years after the Riddle nickel deposit N was discovered in Oregon in 1864, Hanna Coal & Ore Corp. began mining operations. Until 1954 much prospecting and preliminary development work had been done on the property, but no ore had been shipped other than for metallurgical testing. The deposit is being explored by churn drilling and trenching, and a few test shafts have been put down for the purpose of studying the ore in place, determining volume and moisture factors, and gathering bulk samples for pilot plant and smelter tests. In churn drilling, 6-in. casing is driven down 2 or 3 ft behind the drill bit and bottomed at each 5-ft interval. All the sludge for each cased 5-ft interval is dumped through a splitter and one eighth is saved and analyzed. Drillholes are stopped after going through the ore zone and penetrating fresh peridotite in which the nickel content is less than 0.5 pct.

Jan 8, 1957

By H. I-Lieh Huang, O. D. Sherby, J. E. Dorn

RECENT investigations1-4 have suggested that the total plastic strain, C, for high temperature creep under a given stress can be correlated by means of a temperature-compensated time, te- where t is the duration of test, e is the base of natural logarithms, aH is the activation energy for creep, R is the gas constant, and T is the absolute temperature. A typical set of data on which this deduction was based is given in Fig. la. Inasmuch as the e-in t curves for the various temperatures are identical except for their displacement along the In t axis where f and are appropriate functions. If the increase in creep rate with an increase in temperature is exclusively ascribable to a single process involv- ing thermal activation, (T) should equal RT and therefore it = constant [2] where ?= te Assuming the validity of this relationship, ? = ?2 at the same strain, or where the subscripts refer to two alternate test conditions.

Jan 1, 1957

By R. G. Bowman

DISCUSSIONS of processes for the manufacture of white lead generally open with the statement that white lead is the oldest chemical pigment known to man. This fact is of more than historical interest; in the light of the present extensive use of white lead, ii indicates that the .compound possesses characteristics that make it unique among white pigments, and superior to all ;in its particular field. A greater variety of processes have been proposed for manufacturing white lead than for any other one chemical compound. Only a few of these processes have come into commercial use, however, and a large part of the present production here and abroad is made by the process used in ancient times. The outstanding disadvantages of the old process are that it is slow and laborious, affords no control of the product, and yields at best an impure material lacking in uniformity. Improved processes, sometimes classed all together as "quick processes," have had as their main object the shortening of the time required. Most of them accomplish this and some have yielded a superior product as well, but only two or three are now in use commercially. For centuries the manufacture and mixing of paints has been treated as an art, and the practice has been much influenced by tradition and precedent. There is a reluctance to abandon old materials for this purpose, and as few new uses for white lead have been developed, the adoption of the quick processes has been slow. The electrolytic production of white lead is not-new, a large number of processes and forms of apparatus have been proposed and patented within the past 25 years, all directed toward the, production of white lead, wholly or in part, by electrolysis. One or two of these processes were tried commercially but proved unsuccessful.

Jan 9, 1925

By C. S. Matthews, H. M. Girner, C. D. Williams, M. J. Edwardson, H. R. Parkison

Quantitative interpretation of electric logs requires knowledge of formation temperature. In this paper, methods are developed for computing changes in formation temperature caused by circulation of mud during drilling operations. The basis of the method is the mathematical solution of the differential equation of heat conduction. The solution of this equation is presented in a series of graphs. These graphs are used to determine formation temperature disturbance at various radii for arbitrary mud circulation histories. Example comparisons with field results show reasonable agreement. It is concluded that, in general, the temperature disturbances caused by circulating mud are small beyond 10 ft from the wellbore but are quite significant near the wellbore. INTRODUCTION Quantitative interpretation of electric logs requires knowledge of the formation temperature in order to establish the resistivity of the formation water with accuracy. To determine the formation temperature, the temperature disturbances produced by circulating drilling mud must be evaluated. -The objective of this investigation was to develop a method for the numerical determination of these temperature disturbances at any distance from the wellbore as a function of time. The first step was to solve the differential equation describing the temperature behavior in the formation during and after mud circulation. This solution was used to calculate a series of curves relating temperature disturbance to shut-in time for various circulating periods. An "exact" method for computing formation temperatures with the use of these temperature-disturbance plots is described, and the results of an application of this method to a well in Montana are presented. Procedures for approximating formation temperatures are also discussed. BASIC EQUATIONS AND ASSUMPTIONS With the assumptions that (1) cylindrical symmetry exists, with the borehole as the axis, (2) heat flow is 1. The formation can be treated as though it is radially infinite and homogeneous in extent, as regards heat flow. 2. The presence of mud cake can be disregarded. 3. The effect of heat generated by bit action is negligible. 4. After mud circulation ceases, the rate of radial heat flow at the wellbore is negligible and is assumed zero for purposes of calculating temperature change with time. These assumptions are believed to be reasonable because of the agreement achieved between calculated and measured borehole temperature in a well, to be discussed later. Further, the agreement at the wellbore indicates that temperatures in the formation were also approximately correct. since it is the formation temperatures that determine wellbore temperature after ceasing circulations SOLUTION OF THE DIFFERENTIAL EQUATION AND ITS APPLICATION The solution of Eq. 2 for the temperature behavior during and after a single period of mud circulation is

By J. O. Nelson, C. J. Altstetter

Single crystals of hcp cobalt, 3 mm in diameter and up to 35 cm long, were grown using an electron-beam, zone-melting technique. The martensitic-phase transformation was studied in single-crystalline and polycrystalline specimens by making length-change measurements as a function of temperature under various elastic compressive stresses. Upon thermal cycling, single-crystalline or polycrystalline specimens repeatedly transformed almost entirely on the same variant of close-packed plane provided the maximum temperature did not exceed 600°C. Cycling to 1000°C resulted in transformation on more than one {111} variant. This behavior is termed multivariance. The multivariant transformation occurred very rapidly at an M, temperature 2° to 6°C lower than the M, of a transformation which would result in a single-crystal product. Elastic compressive stresses (up to 253 g per sq mm) tended to lower the A, and raise the M, temperatures, decreasing the width of the temperature vs dilatation hysteresis loop. The transformation habit plane and transformation shear direction of an as-grown single crystal were not grossly affected by elastic compressi?ie stress. This was evidenced by similar dilatations on the temperature us dilatation loops joy specimens with and without compressive stress. A dislocation mechanism is proposed to explain the observed results. IT has been shown that, on heating, cobalt transforms martensitically from the hcp to the fcc phase.' The transformation habit plane is (0001)hcp || (lll)fcc and the transformation shear direction is (1010)hcp || (112)fcc. The transformation involves a shear of 1g°28', which may be achieved by a shearing of a/6(112) of every two planes with respect to the plane beneath, thus changing the ABABAB stacking of hcp to the ABCABC stacking of fcc. Associated with the phase change is a 0.3 x 10"3 contraction in the habit plane and a 4.2 X 10"3 expansion perpendicular to the habit plane resulting in a 3.6 x X volume increase on heating.' On cooling, an identical volume decrease takes place. The temperature at which the fcc phase begins to form on heating (A,) is reported as 430°C, and the temperature at which the hcp phase begins to form on cooling from an elevated temperature (A&) is reported as 390oC1,3 Consequently, temperature vs dilatation plots have the form of a hysteresis loop. If heating or cooling is reversed during a transformation, a smaller hysteresis loop results. Upon heating, the transformation is always complete; whereas, fcc is often retained at room temperature as a metastable phase entrapped in the polycrystal-line hexagonal matrix.1,4,5 Two obstacles in the theory of the allotropic-phase transformation of cobalt have been: 1) a detailed knowledge of the product nucleus, and 2) a plausible method of propagation of the transformation. Bilby,8 christian, 7 and seeger 8,9 have suggested a "pole mechanism" as a means of propagation of partiai dislocations from plane to plane. A pole dislocation and a Shockley partial come together at a node. The a/6(112) Shockley partial rotates about the pole dislocation effecting the transformation shear. The pole dislocation must have a 2a/3(111) screw component which causes extension of the transformed region by two atomic planes with each full rotation of the Shockley partial. Bollmannl0 suggested, on the other hand, that transformation propagation occurs due to the stress fields of intersecting (111)-type stacking faults. As faults intersect, a stress distribution is set up about their intersection which is in turn reduced by the emergence of another fault on the second nearest plane. This process continues with the final result of a complete phase transformation. In view of the similarities between deformation and transformation in cobalt, the effect of stress on the transformation would, hopefully, yield valuable information concerning nucleation and propagation. In the present work single-crystalline and polycrystalline specimen length changes were measured as a function of temperature at various compressive loads. PROCEDURE Several orientations of single crystals of hcp cobalt in lengths up to 25 cm were grown by electron-beam floating zone melting from 99.95 and 99.999 pct, 3-mm-diam cobalt rod as supplied by Johnson

Jan 1, 1964

By Henry S. Rawdon

The structure of wrought iron as usually described by metallographists and workers in metal in general is that of a fairly pure iron. Impurities, if present, are usually considered as being in solid solution in the crystals of the ferrite matrix or as forming part of the ever present "slag streaks." Attention is herein directed to one type of these dissolved impurities; to the detection of such impurities, particularly in low-grade irons, and to their possible influence on the physical properties of the metal. The attention of the Bureau of Standards was first directed to wrought iron of the peculiar and unusual characteristics to be described later, in material which had failed in service and was submitted for test. The examination was extended to other grades of wrought iron, to see whether such features are of common occurrence in this class of material. MICROSTRUCTURE OF WROUGHT IRON Usual Structure The general microstructure of wrought iron is so well known that a detailed description of it here is needless. There is shown in Fig. 2 the structure of a sample of Swedish iron which illustrates well the matrix of ferrite crystals in which are embedded the slag threads so characteristic of the puddling process and the subsequent working of the material. The usual commercial product contains varying amounts of the impurities commonly associated with iron and steel, i,e,, manganese, phosphorus, silicon, and sulphur together with small amounts of carbon. Of these, the larger part of the phosphorus and some of the silicon present are held in solid solution in the ferrite while most of the remaining impurities, other than carbon, exist in the in closures of slag. Aside from the discontinuities introduced by the slag streaks the ferrite matrix has the microstructure and appearance of a pure metal. No definite orientation of the various crystals or grains is apparent; deep etching of the specimens reveals no intracrystalline features (i.e., within the grains) other than those noted in " pure " metals in general (etching pits).

Jan 1, 1918

By T. J. Woods

This paper deals with the origin, definition and prevention of scabs on semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. Definition of a Scab The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.—On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters. This is true whether molds are coated or not. Shape.—There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. Experimental Work Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on flat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By T. J. Woods

This paper deals with the origin, definition and prevention of scabs on semifinished rolled-steel product. Mold coatings, which are considered essential in scab prevention, were found to be effective only in relation to the ingot surface of semikilled and killed steels and not necessary for the rolled product. That is to say, the scabs on ingots caused by having been cast in uncoated molds are eliminated in the soaking and rolling operations, therefore are not present on the rolled product. This fact, which is contrary to the average opinion, was established after extensive and thorough experiments had proved the ordinary conception of the origin of scabs to be incorrect. This subject may be of little or no concern to steel plants producing small ingots for the manufacture of small billets and bars, except as it may be of interest in showing why their surface troubles with scabs do not exist on the product of heats with normal pouring practice. But to the producer of large ingots to be rolled into slabs for large plates used in shipbuilding, it is a very important subject. Definition of a Scab The generally accepted opinion is that the individual scabs present on rolled products (as shown by Fig. I) are considered to have been individual splashes on the ingot surface. This opinion was found to be incorrect. Experiments showed that there were no individual scabs on the product that had appeared as individuals on the ingot surface. The single scabs seen are either pieces of a shell that is present near the bottom of all top-cast ingots, or a veneer that may be present on any part of an ingot improperly poured, as when the stream strikes the mold wall. This definition is based on a detailed study of scabs and their characteristics in which the following have been found true: Location.—On the product of heats poured without trouble, scabs, if present, are always on the product that corresponds to the bottom end of the ingot, and usually occur in clusters. This is true whether molds are coated or not. Shape.—There is no regularity as to shape, size or thickness. It is sometimes possible to separate a few pieces and place them together, like pieces of a jigsaw puzzle, indicating that at one time they had been united as one piece. If individual splashes were the origin of scabs, the foregoing would not be true. Instead, the splashes, which occur throughout the pouring of the ingots, would be present uniformly over the entire product and there would be considerable similarity in the shape and thickness of the scabs. Experimental Work Our experimental work was conducted on 200-ton heats of semikilled plate steel tapped into an oval ladle 15 ft. high. All ingots were top-cast direct into 24 by 54 by 82-in. molds, straight-sided, set on flat stools. Two separate studies were made about one year apart, each study extending

Jan 1, 1943

By O. F. Thornton, D. L. Marshall

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By D. L. Marshall, O. F. Thornton

Results of the determination of the inter stitial water content of several core samples from oil reservoirs are presented. Data obtained by the capillary pressure method, which has recently been developed, are compared with water saturations measured in cores cut with oil-base mud and with values calculated from the electrical resistivity of the formation. The agreement between the capillary pressure and other methods, combined with the fact that similar agreement has been obtained by others, indicates that the capillary method properly applied yields results sufficiently accurate for most engineering purposes. In some cases, it may be possible to extend the utility of data obtained with the capillary pressure method by correlation of interstitial water saturation with more easily measured physical properties of the media. Introduction Several methods are in use for determining or for estimating the interstitial water saturation at given points within oil and gas reservoirs. The direct measurement of the water content of cores obtained with nonaqueous fluid in the hole is believed to be an accurate method under most conditions. The water saturation may be calculated by use of the resistivity curves of the electric log,' although this method is not applicable under conditions that exist in some reservoirs. Recently, a method has been developed and described3.' wherein the interstitial water saturation of cores is measured at a capillary pressure such that conditions existing in the reservoir are simulated. The purpose of this paper is to present data obtained by use of this latter method, and to compare the results obtained with determinations made by other means. Method The theory underlying the capillary pressure method applied to petroleum reservoirs has been discussed adequately in the literature by Garrison,2 Leverett,5 and Others.3,6,7 Briefly, and simply, capillary pressure is defined as the difference in pressure between two contacting fluid phases, such as oil and water. For the simplified sand, water and oil system illustrated in Fig I, the pressure difference can be stated as follows:6 where Pc is the capillary pressure in pounds per square inch, ? is the interfacial tension between oil and water in pounds per inch, r1 and r2 are the radii of curvature of the interface between oil and water in inches. Capillary pressure varies in a given reservoir with depth because of the greater density of the water phase as compared with oil or gas. The following equation expresses the difference in pressure between two points: p1- p2 - h?p/144 [2] where p1 — p2 is the capillary pressure difference in pounds per square inch, h is

Jan 1, 1947

By Arnold S. Epstein

Tlze green electroluminescence occurring at liquid-nitvogen temperature in epitaxial gallium phosphide diodes is exarnined using the donor dopants silicon and sulfur. Zinc is used as the p-type diffusant. Two tt~ain peaks are found, namely til 0.56 and 0.535 p. The intensity of the gYeen peak occurring at 0.56 is found to oary as -4"' wlzere Jf is the forward current density and to first order appears to be dependent on the concet~tvation of ionized donovs. Tile vadintive lifetinze fov this process is -10-'sec. The intensity of the 0.56-p lu~ninescence is nt least several ovdevs of magnitude greate,, at liquid-nitvogen temperature than that noted jor the 0.538 radiation for current densities up to about 35 amp per sq cm. The variation oj- the intensity of. the 0.538-p peak with current density caries according to the donor dopant. With sulfur as the donor one has a J12 dependence, whereas when silicon is the donov a J1.5 dependence is noted. Tl~e above can be fitted to a In molecular process (in first order) such as a band to band recombination. The constant B fir band to band vecombination) is found from our experitt~etlt to be of the order of 2 CZI cm per sec, zcl~ereas for tlze impurity vecombination peak (0.56 p]) tile A cotzstor~t is of the order of. 7 x 10-' cu cm per sec. The structuve o/. the diodes at liquid-nitvog-en tett~peruture is oj tlze double injection type, and by carefi~lly selecting. the thickness of the structure one can regulate the onset of the 0.538-p radiation. The diode clzavaclevistics follow an I-Vx laiv where x is >1. Llregatiue resistance in these structures con be correlated with saturation of tlze 0.56- peak. ThE development of high-purity, large single crystals of epitaxially grown gallium phosphide is the ultimate aim of the studies to be reported. While a number of papers and reviews' have been presented on properties of gallium phosphide grown from gallium solution and from the melt, less attention has been paid to the properties of epitaxial gallium phosphide grown from the vapor. In the studies to be reported we have examined the effects of shallow donor impurities, primarily silicon and sulfur, at liquid-nitrogen temperature, on both the electrical and green electroluminescent properties of carefully characterized single-crystal epitaxial Gap. I) EXPERIMENTAL PROCEDURES A) Material Preparation and Properties. The samules used in this investigation were single-crystal n-type epitaxial gallium phosphide. he single crystals were synthesized from the elements by vapor transport and epitaxial deposition on single-crystal gallium arsenide substrates. Typical transport agents used were chlorides. The growth procedures are described in more detail in Ref. 2. The samples were grown in the (111) orientation and had thicknesses up to 480 . Following the growth, the GaAs substrate was removed from the epitaxial Gap by etching in nitric acid. The Hall effect and resistivity of these n-type samples were measured as a function of temperature and analyzed for impurity content and compared with spectroscopic emission analysis. The results are given in greater detail in Ref. 3 but a summary is noted in Table I. In Table I, AED denotes the donor ionization energy, Nd is the donor impurity concentration, lvA is the acceptor impurity concentration, NI is the total impurity concentration, Rip vs temperature is the measured Hall mobility-temperature relationship from liquid nitrogen to about 400"K, n(77"K) is the measured carrier concentration at liquid nitrogen, and R/p(77'~) is the measured Hall mobility at liquid nitrogen. Good agreement is noted between electrical and emission analysis for the major donor impurity, silicon, in the two materials where it is a major constituent. In the case of the two samples SC90-6 and AP138-3(111) B which were sulfur-doped the ionization energy found from the electrical data is in good agreement with that reported for sulfur.4 The acceptor impurities are not known, although from the presence of magnesium in the samples as indicated by emission analysis and its known role as an acceptor in GaP,4 magnesium could be present as an acceptor. Similarly, since silicon is known to be an amphoteric impurity4 it may also be present as an acceptor in the Gap.* The *A small band has been noted at 0.625 11 in samples SC90-6, SC76-4, and SC77-4, suggesting according to Ref. 5 that sillcon could be present as an acceptor In these samples since these authors have found this peak to represent a donor-silicon emission. presence of calcium deduced from emission analysis is not correlatable with the electrical analysis and its presence as an electrically active impurity should be questioned. B) Sample Preparation and Diode Fabrication. The original slices were of the order of 2 sq cm in area witi the (111)B face up. The material was cleaved and sectioned and the best pieces selected (i.e., those which visually appeared to have the least strain and defects). The samples were polished, lightly etched, and cleaned in trichloroethylene. Zinc was diffused in a closed tube at 800°C to form a p-n junction. Diodes were made from these samples. The depth of junction varied, but did not exceed 10 p depth. The back side of the slice was lapped back and a low-resistance n-type contact was formed (at 600°C in forming gas) to an Au-Mo tab with a hole in the middle for

Jan 1, 1968

By P. S. Miller, S. H. Ash

EXTENSIVE and diversified resources justify large populations and great industries. To carry on the business of commerce and meet the demands of large populations, the utilization of tunnels in some form for transportation purposes constitutes an important link in modern civilization. The driving of tunnels has been appropriated by the tunneling branch of the heavy-construction industry, and the progressive steps taken by modern tunnel builders were not even dreamed of 50 years ago. Great strides have been made toward more rapid progress in tunneling in the United States during the past 10 years. Tunneling consists of a definite cycle of operations developed from ideas that are crystallized and translated into action programs through various engineering phases that begin with the first preliminary survey and do not end until the job is completed. Once the line of the bore is established and a time set for the completion of the work, the face must advance according to estimates prepared before the work commences. This schedule must be followed in regular sequence from the moment the drills start against a new face of rock until they are ready again to drill the succeeding face, constituting a round.1 Mining is largely tunneling carried on under conditions often more inherently hazardous than actual tunnel construction, but for various reasons1 tunneling is more hazardous than mining in any branch of the mineral industry, On the other hand, obstacles are sometimes encountered in heavy-construction tunneling projects that when met in mining enterprises do not offer comparable tasks to avoid or overcome them. One of these is the existence of water under high pressures. In mining enterprises, various alternatives offer a solution in driving a tunnel, even to the extent of its discontinuance or the abandonment of the mine, but a "construction" tunnel usually must go forward because some important project depends largely if not entirely upon it. This paper describes an unusual method of driving a water-supply tunnel through rock carrying water under pressures and conditions that did not permit the use of ordinary tunneling methods. THE DELAWARE AQUEDUCT The new Delaware aqueduct is a Manhattan project of some magnitude; when completed, it will contain what probably will be, for some time to come, the longest tunnel in the world. Various features in its construction are currently described in the trade journals of the construction industry, and informative engineering details are given in the Delaware Water Supply News, published twice a month by the Board of Water Supply of the City of New York. Work was begun on this project on March 24, 1937. The tunnel will convey water from reservoirs at the headwaters of the Delaware River to the City of New York.

Jan 1, 1942

By S. L. Lopata, E. B. Kula

A variation of yield and tensile strength with direction has been noted in heat-treated 4340 steel which had been warn-worked by rolling in the austenitic condition prior to quenching. Measurements by X-rays showed a preferred orientation of martensite crystals. Various ideal preferred orientations of martensite were calculated by assuming a preferred orientation for austenite and transforming this to martensite by the Kurdjumov -Sachs and Nishiyama relationships. Comparison with the measured preferred orientation showed that the ideal rolling texture for austenite in 4340 steel could be expressed as a (112) [111] texture with a component of (110) [112]. No evidence was found for any fiber axis in the rolling direction, or fop- a (123) [412] texture. The observed martensite pole figures can be adequately accounted for by these ideal austenite textures and by the Kurdjumou-Sachs or Nishiyama transformation relationships between austenite and martensite. ALTHOUGH preferred orientations are found in cold-rolled steel sheet and in many nonferrous metals, they are not generally encountered in wrought, heat-treated high-strength steels, since such steels are generally not cold worked sufficiently to develop a strong texture, and any texture that is present is removed during heat treatment by the phase transformations taking place. This report gives details on a preferred orientation found in warm-rolled and hardened 4340 steel. In a recent study, a special combination heat-treating and working technique was used in which 4340 steel was deformed in the austenitic condition, and before re crystallization of the austenite could occur, quenched to form martensite.' Since the austenite was unrecrystallized, it was cold worked and hence could have contained a preferred orientation which could be transmitted to the martensite on quenching, and this in turn could be manifested as a directionality of mechanical properties. Such a directionality of properties was found as a result of working, and this prompted an X-ray study of the preferred orientation. Literature Survey— Rolling Texture in Face-Cen-tered-Cubic Austenite—M a preferred orientation is found in a rolled and hardened steel, it is first appropriate to consider what texture existed in the austenite as a result of the rolling but prior to the transformation to martensite. The changes taking place as a result of the austenite-martensite transformation are then considered. In view of the instability of austenite in 4340 steel at low temperatures, no direct determination of the austenite texture was made. However, an estimate of the texture for austenite in 4340 steel may be made by considering the textures found for other face-centered-cubic metals. Barrett' has reviewed the rolling textures for many materials. The most common orientation in face-centered-cubic metals has the (110) planes parallel to the rolling plane and the [112] directions parallel to the rolling direction, or (110) [112]. Other orientations found are (112) [111], as well as (100) [001], (110) [001], and others. Beck and his co-workers, using quantitative pole figures, report that (123) [121],3 later corrected to (123) [412],4 better describes the ideal orientation. smallman5 reported that the ideal preferred orientation for high-purity face-centered-cubic metals is (123) [121], but that there is a transition to (110) [112] as solid solution elements are added. The latter texture tends to occur more readily at lower temperatures. This transition between the two textures was explained by differences in the slip characteristics with concentration or temperature. More recently, Jones and Fell6 concluded that the (123) [412] texture for face-centered-cubic metals could equally well be represented by a mixture of (110) [112] and (112) [111] textures, and hence it had no physical reality. From the above results it can be seen that there is no agreement on the "ideal" texture for fcc metals and, hence, no firm basis for assuming a texture for austenite in 4340 steel. Therefore, the orientations (110) [112], (123) [412], and (112) [111] have been considered in the following.* *The (123) [4121 is identical to the (123) [121] rotated 90 deg. Orientation Relationship between Austenite and Martensite—When martensite forms from austenite, certain crystallographic planes of the martensite are parallel to planes in the austenite. This orientation relationship was first determined by Kurdjumov and

Jan 1, 1960

By John A. Ames

Webster's dictionary nearly equates portland cement with its current primary definition of cement. While such equation may be a triumph of common usage, the confusion between the terms cement and concrete unfortunately is very widespread. Full definition of cement properly would extend to many substances, but for purposes of this chapter cement is restricted to "varieties" of portland cement including "portland-pozzolan" cement. Among the usually recited historical notes concerning cement is that it was developed by the Romans. Their use of cement in the great structures of Rome, and even in the far corners of their Empire, such as Hadrian's Wall in the north of England, testifies to the antiquity of a major cement industry. From English sources we know of John Smeaton's carefully proportioned hydraulic cement mixed in 1756 and of Joseph Aspdin's patented cement to which, in 1824, he gave the name portland cement. (He claimed that his cement mortar looked like the famous dimension limestone quarried from the Isle of Portland on England's south coast.) The year 1971 marked the centennial of portland cement manufacture in the United States. A fair historical account of the many real contributors to the cement industry between 1756 and 1972 unfortunately would be too extensive for this chapter. Development of rotary kiln practice and burning at higher temperatures clearly was the major move into today's technology. As part of the 4th edition of Industrial Minerals and Rocks, this chapter on utilization focuses on inferred interests of the anticipated readers. The main period for which statistics are cited generally is that since the 3rd edition (1960) of this same volume. Cement manufacture is the processing of selected and prepared mineral raw materials to produce the synthetic mineral mixture (clinker) that can be ground to a powder having the specified chemical composition and physical properties of cement. Cement making incorporates a number of distinct steps, but it is characterized by the key pyroprocessing (or "burning") step, which brings about the necessary changes in the raw materials. This pyro processing is a chemical process. Conversion of large volumes of mineral raw materials into specification-controlled cement at relatively low cost is the objective. Statistics on the cement industry are of uneven quality. The U.S. Bureau of Mines (USBM) is the principal collector of available data. These statistics can be only as good as the quality of information supplied by the reporting companies. The data perhaps most often questioned relate to productive capacity of the industry. The questions submitted by USBM are valid, nevertheless, and the information gained from them, as good as is available, is what is generally used. The Portland Cement Association also is a source of much quality information. The year 1972 witnessed a test of the adaptability of cement industry statistics. This was the year of conversion from barrels and sacks of cement as the units of measure to tons and hundredweights. The barrels and sacks related to volumetric measures in that a sack was judged to be 1 cu ft (weighing a "standard" 94 lb). A barrel was 4 sacks. Volumes of concrete are stated in cubic yards, and the number of cubic feet of cement in a cubic yard of concrete was a sensible approach to the mensuration involved. However, cements do not weigh the same amount from plant to plant or from type to type, and the buyer was more interested in getting an assured weight for his money than in "buying air." Thus, a sack, in accepted practice, became 94 lb instead of 1 cu ft, and a "barrel" became 376 lb, regard- less of whether it would fit into 4 cu ft of space. With the de facto dealing in weight rather than in volumes, the awkward numbers made little

Jan 1, 1975

By Craig R. Barrett, Jack L. Lytton, Oleg D. Sherby

The types of substructures developed during high-temperature creep of (110)[001]-oriented polycrys-talline Fe-3.1 pct Si were examined by electroetching of dislocation sites. Edge dislocations were observed to accumulate adjacent to grain boundaries and poly-gonize perpendicular to their glide planes to form a "Pile-up" of nearly parallel tilt boundaries. The dislocation density developed within the grains during steady-state creep was found to increase with increasing stress. The formation of periodically spaced groups of edge dislocations along grain boundaries was observed, and it was proposed that these formed to relive bending stresses at grain boundary shear .faults. Grain boundary serrations developed at these faults, and it was suggested that this was a result of localized grain boundary migration at the polygonized groups. THE authors have conducted a series of high-temperature creep tests on (110)[001]-oriented poly-crystalline Fe-3.1 pct Si sheet. The creep specimens were examined at various stages of creep by means of electrolytic etching of dislocation sites using the chrome-acetic acid solution developed by Morris.' Hibbard and Dunn2 have demonstrated that the etch pits produced with this technique correspond to single dislocations. It is the purpose of this paper to present and discuss the dislocation substructures which were formed during high-temperature creep at constant stress. EXPERIMENTAL PROCEDURES The polycrystalline Fe-3.1 pct Si sheet employed in this study contained a (110)[001] texture. This texture was quite strong, and the elastic properties of the sheet closely approached those of a single crystal of iron.3,4 A typical analysis in weight percent for this material is 3.1 Si, 0.1 Mn, 0.003 C,

Jan 1, 1965

By AIME AIME

The Bulletin. The Bulletin of the Institute will be issued hereafter monthly instead of bi-monthly as heretofore. Among other reasons for this change, it is desired to effect thereby the earlier transmission to members of important papers, lists of candidates tin? membership, and other items of timely information. The New Haven Meeting. As already announced in special circular, the XCVIth meeting of the institute for the reading and discussion of papers will be held at New Haven, Conn., beginning Feb. 23, 1909. The Secretary of the Local Committee is Prof. J. D. Irving, Box D, Yale Station, New Haven. The program embraces visits to many interesting works in New Haven, Ansonia, Bridgeport, etc. The leading topics for discussion at the sessions will lie: The Conservation of Natural Resources; A Sea-Level Canal at Panama; and The Technical Education of Mining Engineers. But papers on other subjects also are announced. Lt is probable that a supplementary session of this meeting, will be held in New York City, at some time during March, 1909, as a joint session with other national engineering societies, for the farther discussion of the subject of The Conservation of Natural Resources. A Pacific Coast Meeting. It is now reasonably certain that the XCVIIth meeting will be held oil the Pacific Coast, including a. visit to the Exposition at Seattle, and various other points en. route going or coming, depending upon the route and program finally adopted. (lore definite information will be announced at the New Haven Meeting, or at the earliest possible date thereafter.

Jan 1, 1909

By E. R. Dean

A wire-feed mechanism has been employed to fabricute metal alloy film resistors to various sheet resistivities on oxidized silicon substrates. The effect of several thousand hours storage in air at elevated temperatures on the resistance and temperature coefficient of resistance is presented. Unprotected films of- sheet resistivity between 100 and 500 ohms per sq fabricated at 300°C substrate tenzperatures were unstable when stored at 150°Cfor extended periods. The higher sheet resistivity films exhibited the greatest instability; however, even the 100 ohms per sq films drijted excessively for device application. When stored at still higher temperatures, the normalized resistance increases to maximum, then decreases until a minimum value is obtained, then finally increases in resistance until open. The use of a protective overcoating of SiO has had considerable benejicial effects on the film stability, so that 250 ohms per sq films deposited on 300°C substrates are now stable after 1000 hr storage at 250°C and possess a temperature coefficient of resistance less than 200 ppm per C. The use of a low substrate temperature during depositon (100°C) enables the preparation oj resistors with very low tenperature coefficients of resistance (10 to 20 ppnl per 'C). However, these films are less stable than their higher substrate temperatuve counterparts. During extended storage, the resistance of the protected films always decreases with lower substrate films exhibiting larger normalized resistance decreases. This resistance decrease is accompanied by a linearly related increase in the temperature coefficient of resistance. The electrical behavior of these films may be explained by postulating That the structure of the films is in the transition region between thick continuous films and ultrathin island structure films so that the conductivity is the restlt of both electron scattering and tunneling-activated charge carrier creation between neighboring grains. The annealing behavior when thermally aged is the result of defect anneal, grain growth, and selective oxidation. TheRE is a considerable interest in thin metallic films for use as resistor elements in microelectronic circuits.1,2 These resistor films must be stable when exposed to elevated-temperature storage or operating ambient, possess low temperature coefficients of resistance (hereafter referred to as T.C.R.), and be of a high enough sheet resistivity to be useful. The resistivity and T.C.R. of a thin metallic film are determined by the structure and thickness of the film. Hence the stability of the film when exposed to stress would depend on the stability of the structure. The resistivity of a thin film is the result of the electrons' interaction with the lattice vibrations (electron-phonon scattering), scattering of electrons due to impurities, defects, and grain boundaries and specula reflection from the film surfaces.3' All of these effects serve to reduce the electron mean free path and result in a resistivity higher than the ideal bulk. In ultrathin films possessing essentially an island structure consisting of a planar array of aggregates separated by a few to a few tens of angstroms, conduction is dominated by a combination of tunneling and activated charge carrier reation. Thin films would be characterized by relatively low resistivity, positive T.C.R., and reasonable structure stability whereas ultrathin films possess unstable structures, negative T.C.R., and exhibit high resistivity. Feldman6 has investigated films intermediate between the two regions and postulates that the resistivity of a film in the transition region is composed of two linearly additive parts: that due to the resistance of the grains and that due to the gaps. The grain resistivity would represent the scattering of the conduction electrons by defects, surfaces, and phonon interaction while the gap term represents the tunneling contribution. For gold and platinum films, he found as the film structure becomes progressively less continuous, corresponding to thinner films, the absolute value of the T.C.R. becomes progressively smaller until negative values are observed with respective zero T.C.R.'s at about 35 and 150 ohm per sq, respectively. Recently the author7 investigated the behavior of a multicomponent alloy of nickel, chromium, and iron and found the T.C.R.'s of these films decrease with decreasing substrate temperature during deposition. The lower T.C.A. associated with lower substrate temperatures was attributed to an increased contribution to the total resistivity from the negatively temperature-dependent gap tunneling since it is well-known that thin films deposited on low-temperature substrates consist of a higher density of smaller grains than the same sheet resistivity films deposited on higher-temperature substrates. Under conditions of thermal anneal, the author found that, when various sheet resistivity films fabricated at 300°C substrate temperature are exposed to extended storage in air at 300°C, the thinner films increase in resistance until open, while the thicker films

Jan 1, 1967