Search Documents

By AIME

One of the operations of the J. L. Shiely Co. is quarrying in a hard granite gneiss with intrusions of gabbro or trap. During the winter of 1948-1949 the quarry ramp was lowered about 30 ft and during the 1949 season practically all drilling was done from the quarry floor, developing a face from 72 to 83 ft for the entire quarry area. The performance and cost table shows our record for 1948 and 1949.

Jan 1, 1950

By S. J. Harrison

One of the operations of the J. L. Shiely Co. is quarrying in a hard granite gneiss with intrusions of gabbro or trap. During the winter of 1948-1949 the quarry ramp was lowered about 30 ft and during the 1949 season practically all drilling was done from the quarry floor, developing a face from 72 to 83 ft for the entire quarry area. The performance and cost table shows our record for 1948 and 1949.

Jan 9, 1950

By Vard H. Johnson

IN 1943 the U. S. Bureau of Mines undertook drilling in an effort to develop new reserves of coking coal in an area near Paonia, Colo., as a part of an attempt to alleviate the shortage of known coking coal of good quality in the western United States. Geologic mapping of the area was undertaken by the U. S. Geological Survey with the purpose of first furnishing guidance in location of drillholes and later aiding in interpreting the results of the drilling. The drilling program was under the general supervision of A. L. Toenges of the U. S. Bureau of Mines. J. J. Dowd and R. G. Travis were in charge of the work in the field. Geologic mapping was started by D. A. Andrews of the Geological Survey in the summer of 1943 and was continued from the spring of 1944 to 1949 by the writer. The first few holes drilled failed to locate coking coal, but in the summer of 1944 coking coal was discovered by drilling 6 miles east of Somerset, Colo., the site of present mining. In the succeeding years, 1945 to 1948, 100 to 150 million tons of coal suitable for coking were blocked out by drilling. The ensuing discussion of the geologic controls on the distribution of coking coal in the area is based on the geologic mapping as well as the drilling done in the Paonia area, more complete descriptions of which have appeared or are in process of publication."' In order that the possible geologic controls affecting the present distribution of coking coal may be considered, it is necessary to discuss briefly the indicators of coking quality coals. Coking Coal Coal that cokes has the property of softening to form a pastelike mass at high temperatures under reducing conditions in the coke oven. This softening is accompanied by the release of the volatile constituents as bubbles of gas. After release of the contained gases and upon cooling, a hard gray coherent but spongelike mass remains that is referred to as coke. This substance varies greatly in physical properties and, to be suitable for industrial use, must be sufficiently dense and strong to withstand the crushing pressure of heavy furnace loads. Western coals have a generally high volatile content and therefore form a satisfactory coke only when they attain a rather high fluidity during the process of heating arid distillation in the coke oven. When this high degree of fluidity is developed, the volatile constituents escape and leave a finely porous coke. On the other hand, when the degree of fluidity is low the product is an excessively porous and therefore physically weak mass that is called char." Small quantities of oxygen present in coal are believed to decrease the fluidity of the material during the coking process and to favor the development of char rather than coke. In consequence, coal chemists have for some time considered the possibility of developing an index to coking qualities by inspection of chemical analyses of coals.' A formula has now been developed that does permit a rough preliminary estimate of the cokability of coal on the basis of the analysis on an ash and moisture-free basis. Coals may be eliminated as possible coking fuels if the oxygen content is greater than 11 pct. Similarly the ratio of hydrogen to oxygen must be greater than 0.5 and the ratio of fixed carbon to volatile constituents must be greater than 1.3. If the coal, on the basis of these limiting factors, appears to have possible coking qualities, the following formula permits determination of the coking index: a+b+c+d Coking index = -------- 5 a equals 22/oxygen content on ash and moisture-free basis, b equals two times the hydrogen content divided by oxygen content on moisture and ash-free basis, c equals fixed carbon/l.3 x volatile matter, and d equals the heating value on moist, ash-free basis/13,600. Coking indices higher than 1.0 suggest that the coal will coke, and indices above' 1.1 indicate good coking tendencies. Although generally usable, this formula 'is not completely satisfactory because the percentage of oxygen shown in ultimate analyses is derived only by difference; i.e., by subtracting the sum of the percentages of the constituents determined analytically from 100 pct. Although the coking index indicates the coking tendencies of coal, it is necessary to make physical tests of coke before its industrial value can be determined. The U. S. Bureau of Mines has developed a standard procedure for determining the approximate strength of coke that would be formed from a given coal. In this test one part of ground coal, mixed with 15 parts of carborundum, is baked to form a standard briquette. The weight, in kilograms, necessary to crush the briquette is termed the agglutinating index. This test determines the relative fluidity attained in the coking process by measuring the cementing strength of the coal in the briquette. A

Jan 1, 1953

By Vard H. Johnson

IN 1943 the U. S. Bureau of Mines undertook drilling in an effort to develop new reserves of coking coal in an area near Paonia, Colo., as a part of an attempt to alleviate the shortage of known coking coal of good quality in the western United States. Geologic mapping of the area was undertaken by the U. S. Geological Survey with the purpose of first furnishing guidance in location of drillholes and later aiding in interpreting the results of the drilling. The drilling program was under the general supervision of A. L. Toenges of the U. S. Bureau of Mines. J. J. Dowd and R. G. Travis were in charge of the work in the field. Geologic mapping was started by D. A. Andrews of the Geological Survey in the summer of 1943 and was continued from the spring of 1944 to 1949 by the writer. The first few holes drilled failed to locate coking coal, but in the summer of 1944 coking coal was discovered by drilling 6 miles east of Somerset, Colo., the site of present mining. In the succeeding years, 1945 to 1948, 100 to 150 million tons of coal suitable for coking were blocked out by drilling. The ensuing discussion of the geologic controls on the distribution of coking coal in the area is based on the geologic mapping as well as the drilling done in the Paonia area, more complete descriptions of which have appeared or are in process of publication."' In order that the possible geologic controls affecting the present distribution of coking coal may be considered, it is necessary to discuss briefly the indicators of coking quality coals. Coking Coal Coal that cokes has the property of softening to form a pastelike mass at high temperatures under reducing conditions in the coke oven. This softening is accompanied by the release of the volatile constituents as bubbles of gas. After release of the contained gases and upon cooling, a hard gray coherent but spongelike mass remains that is referred to as coke. This substance varies greatly in physical properties and, to be suitable for industrial use, must be sufficiently dense and strong to withstand the crushing pressure of heavy furnace loads. Western coals have a generally high volatile content and therefore form a satisfactory coke only when they attain a rather high fluidity during the process of heating arid distillation in the coke oven. When this high degree of fluidity is developed, the volatile constituents escape and leave a finely porous coke. On the other hand, when the degree of fluidity is low the product is an excessively porous and therefore physically weak mass that is called char." Small quantities of oxygen present in coal are believed to decrease the fluidity of the material during the coking process and to favor the development of char rather than coke. In consequence, coal chemists have for some time considered the possibility of developing an index to coking qualities by inspection of chemical analyses of coals.' A formula has now been developed that does permit a rough preliminary estimate of the cokability of coal on the basis of the analysis on an ash and moisture-free basis. Coals may be eliminated as possible coking fuels if the oxygen content is greater than 11 pct. Similarly the ratio of hydrogen to oxygen must be greater than 0.5 and the ratio of fixed carbon to volatile constituents must be greater than 1.3. If the coal, on the basis of these limiting factors, appears to have possible coking qualities, the following formula permits determination of the coking index: a+b+c+d Coking index = -------- 5 a equals 22/oxygen content on ash and moisture-free basis, b equals two times the hydrogen content divided by oxygen content on moisture and ash-free basis, c equals fixed carbon/l.3 x volatile matter, and d equals the heating value on moist, ash-free basis/13,600. Coking indices higher than 1.0 suggest that the coal will coke, and indices above' 1.1 indicate good coking tendencies. Although generally usable, this formula 'is not completely satisfactory because the percentage of oxygen shown in ultimate analyses is derived only by difference; i.e., by subtracting the sum of the percentages of the constituents determined analytically from 100 pct. Although the coking index indicates the coking tendencies of coal, it is necessary to make physical tests of coke before its industrial value can be determined. The U. S. Bureau of Mines has developed a standard procedure for determining the approximate strength of coke that would be formed from a given coal. In this test one part of ground coal, mixed with 15 parts of carborundum, is baked to form a standard briquette. The weight, in kilograms, necessary to crush the briquette is termed the agglutinating index. This test determines the relative fluidity attained in the coking process by measuring the cementing strength of the coal in the briquette. A

Jan 1, 1953

By A. U. Seybolt

The pressure-temperature relations required to maintain the existence of Si3N4 in silicon-iron of 0.44-11.7 pet Si have been partially explored. The critical data obtained have allowed the calculation of some thermodynamic quantities, and have shown evidence of an order-disorder two-phase field extending at 800°C from about l pet to 5.5 pet Si. THE presence of silicon nitride in electrical sheet, nominally about 3 1/4 pet silicon, balance iron, has been described by several authors'" but there has been some discrepancy among them regarding the identity of the nitride. Also, little has been reported on the quantitative thermodynamic prop- erties. In the work to be reported here, the nitride has been found to be more stable than described by Corney and Turkdogan." Several silicon nitrides have been described in the past, including SiN, Si3N4 and Si2N4 (see, for example, Abegg6 and Pascal7). However, the literature on nitrides other than Si,N, is all very old. No recent investigators using the more powerful tools available today have reported the presence of any nitride other than S3,N4. W. B. Hicke and L. R. Brantley8 in 1930 determined the dissociation pressure of Si3N4 which they made by reacting nitrogen

Jan 1, 1959

The State Mining Experiment Station, Missouri School of Mines and Metallurgy, Rolla, Mo Charles H. Fulton, Director of the School of Mines Martin H. Thornberry, Director of the Mining Experiment Station. From the State Mining Experiment Station are issued all the general and technical bulletins of the School of Mines The latest bulletin containing a complete list of publications will be sent upon application to the Director of the Station Residents of the state may obtain bulletins as issued without charge, or may ask to be placed on the mailing list. Nonresidents should write to the Director for further information concerning specific bulletins. From the long list of bulletins the following have been care¬fully selected as being most likely to interest the geologist and the mining engineer. Vol 8, No. 1 (1916), Bibliography of concentrating ores by flotation, by J Cunningham, vol 1, No 3 (1912), Some apparatus and methods for demonstrating rock drilling and the loading of drill holes in tunneling, by L E Young, vol 2, No 1 (1915), Comparative tests of piston drill bits, by C R Forbes and L M Cummings; vol 2, No 3 (1916), Cupellation losses in assaying, by H. T Mann and C. Y Clayton; vol 4, No 1 (1917), The hydrometallurgy and electrolytic precipitation of zinc, by F D. James; vol 4, No 2 (1917), The effect of additional agents in flotation, pt 1, by M. H. Thornberry and H T. Mann, vol 5, No 1 (1919), The carbonization of Missouri cannel coals, by H L. Dunlap, K. K. Kershner and V. X Smiley. Vol 5, No. 4 (1921), Coal mining methods in Missouri, by W W Weigel, vol 6, No 1 (1921), The problem of the St Peter sand¬stone, by C L Dake, 50 cents, vol 6, No. 2 (1922), Bibliography on the electrothermic metallurgy of zinc, by B M. O'Harra, vol 6, No. 4 (1923), Experiments on the distillation of zinc from complex zinc-lead-silver ores, by B M. O'Harra and E S. Wheeler, vol 7, No 3 (1924), Underground loading devices, by C. E. van Barneveld, 81; vol 7, No. 4 (1924), Briquetting of zinc ores, by B. M. O'Harra; vol. 8, No 2 (1925), A treatise of Missouri clays, by M. H. Thornberry.

Jan 1, 1933

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

Page Foreword. By Edmund M. Wise..................... 3 A.I.M.E. Officers and Dircctors...................... 4 Institute of Metals Division Officers and Committees............ 7 Institute of Metals Division Annual Award Certificate............ 8 Institute of Metals Division Lectures and Lecturers............. 9 Photograph of E. H. Dix, Jr., Institute of Metals Division Lecturer...... 10 PAPERS Acceleration of the Rate of Corrosion by High Constant Stresses. By E. H. Dm, JR. (Institute of Metals Division Lecture, T. P. 1204).......... 11 Variation of Internal Friction with Grain Size. By Clarence Zener and R. H. Randall. (T.P. 1146, with discussion) .............41 Changes in Damping Capacity during Annealing of Alpha Brass. By John T. NoRton. (T.P. 1168, with discussion)................49 An Electron Diffraction Study of Anodic Films. By R. A. HarrinQton and H. R. Nelson. (T.P. 1158).....................62 Determination of Orientations by Etch Pits. By Charles S. Barrett .and L. H. Levenson. (T.P. 1171, with discussion).............76 Process of Precipitation from Solid Solution, I—A Crystallographic Mechanism for the Aluminum-copper Alloys. By Carl H. Samans. (T.P. 1186). . . 85 Age-hardening of Aluminum Alloys, IV — Discussion of the Theory. By WilTJam L. Fink and Dana W. Smith. (T.P. 1083, with discussion). . . 95 Structure of Aluminum after Compression. By Charles S. BaRREtt and L. H. evensonON. (T.P. 1104, with discussion)................112 Recrystallization Texture of Aluminum after Compression. By ChaRlEs S. BarRett. (T.P. 1141, with discussion)................128 Plastic Deformation and Recrystallization of Aluminum Single Crystals. By J. A. Collins and C. H. Mathewson. (T.P. 1145, with discussion) . . . 150 Recovery and Recrystailization in Long-time Annealing of 70-30 Brass. By S. E. Maddigan and A. I. Blank. . (T.P, 1166, with disonssion).....170 Correlation of Deformation and Recrystallization Textures of Rolled 70-30 Brass. By R. M. Brick. (T.P. 1144, with discussion).........193 Tensile Deformation of Critically Oriented Brass Crystals. By H. L. Burghoff. (T.P. 1149).............................214 Recrystallization of Lead. By Paul A. Beck. (T.P. 1101, with discussion). . 222 Simple Method of Thermal Analysis Permitting Quantitative Measurements of Specific and Latent Heats. By Cyril Stanley Smith. (T.P. 1100, with discussion).............................236 Metallographic Study of Internal Oxidation in the Alpha Solid Solutions of Copper. By Frederick N. Rhines. (T.P. 1162, with discussion). . . . 246

Jan 1, 1940

By R. C. Gifkins, K. U. Snowden

The value of the index n in power ktivs for the stress sensitivity of minimum creep rale at lead is derived front results drawn from lite literature and from previously unpublished nork on commercial (99.99 pel) and high-purity (99.999 pel) lead polycryslalline and hi crystal specimens. In tests al 0.5Tm (22 to 50'C) for slvesses below 250 psi, n fulls to mily for poly-cr,yslullirle specimens, single crystals, and bicrystals, and toy grain boundary sliding in bicrystals. Between 250 and 500 psi there is a tyansilion range and, for the polycrystalline specimens al least, u high-stress regime for 500 to 1500 psi where n is 5 or 6. These results are such that none of the suggested stress taws can he used to extrapolate to very loir stresses. Meclianisms for deformation in Ike grains and toy grain boundary sliding in the low-strcss regime are outlined. In particular, the mechanism for grain boundary sliding involves sliding controlled by diffusion from tensile to compressire Ledges. predictions based on this model give promising numerical agree-nicul with experiment. II is suggested that the mechanism for grain boundary sliding may he important in other circumstances, e.g., in creep of ceramic materials or superplaslicity, because it can operate with lille or no dislocation aclirity. WhEN the stress dependence of secondary creep rate is represented by a power law the values taken by the stress exponent n are found to vary between 1 and 7, see, c.g., Garofalo.' In Eq. 1 11 u is the applied stress and A a constant. The case for accepting values of v = 1 rests principally upon tests at high temperatures (>0.9Tm) and there have only been isolated tests at lower temperatures (rather than plots of creep rate against stress) for which the creep rates are such that some form of Nabarro-Herring creep with n = 1 is applicable. Hanson5 and Greenwood and cole6 plotted creep rate against stress for tests made in the vicinity of 0.5Tw, and found a "creep yield", so that below a certain low stress the creep rate was linearly related to stress: these observations appear to have been subsequently ignored. Various models have been proposed which agree with a large body of experimental results in which n equals -5 at high stresses (e.g., weertman7 and McLean8). Various alternatives to Eq. [1] have been proposed principally as a means of unifying creep data, but sometimes, it seems, in order to obviate the necessity for assuming a series of regimes of deformation associated with the various values of n; further refer- ence to these will be made in the section on stress laws. This paper calls attention to extensive results which show n = 1 for the creep of lead at room temperature (0.5 T,). RESULTS Fig. 1 is a composite diagram based on figures in the literature6,9,10 with additional results obtained by the present authors and their colleagues11,12 in the course of a number of investigations not directly concerned with stress sensitivity. In Fig. 1 In creep rate is plotted against In stress. The curves show results for two kinds of material. Lead I is of commercial purity (99.99 pct Pb) and lead IT a specially refined material, hydrogen-purified to remove oxygen; it contains 99.999 pct Pb. Curve A is for lead I in polycrystalline form (grain diameter 0.02 to 0.05 cm) at room temperature (22' to 26°C). Curve B1 is for lead I, polycrystalline, tested at 50C. Curve B2 is for lead 11, polycrystalline (grain diameter 0.02 cm), tested at room temperature (22 O- Curves C to F relate to tests made of bicrystals of lead 11: all of the same nominal orientation ("Y" in Ref. 12). Curves C and V are for creep within the component crystals of the bi crystals at 22°C (AB and CD in Fig. 2). Curve E is for creep measured in a gage straddling the boundary, approximately 0.15 mm either side (BC in Fig. 2). Curve F shows rates of grain boundary sliding (as distinct from strain rates in the other curves), obtained by averaging the offsets of six marker lines on the bi-crystal boundaries. The principal feature of the results is that the stress sensitivity falls into two distinct regimes, according to whether the stress is below approximately 250 or above 500 psi (there is a transitional range between 250 and 500 psi). The new result is that below -250 psi two of the curves (A and BI) give a value of n 1, and the other curves also drop below n - 2 to -1.5 but do not extend to low enough stresses to show clear evidence of n 1. At very high stresses the curves tend to give values of n - 6, as previously determined in other investigations. Curve R2 for the high-purity lead in polycrystalline form at room tenlperature almost merges with B, and thus gives new significance to the values for stresses of 150 and 200 psi; previously'3 these points had seemed to fall away from the curve of slope -3, but they now can be seen as almost completing a transition to n = 1. It should be noted that there was originally considerable apparent scatter in the results for the high-purity lead. However, this was found to be associated with annealing conditions or variations in residual content of oxygen and curve B2 was constructed using the highest rate (i .e., the rate for the purest lead) determined for each stress during the course of various investigations over the years: altogether, some forty tests were used in constructing curve R2.

Jan 1, 1968

By Subhas G. Malghan

Feldspathic deposits occur widely throughout the United States, but North Carolina, California, Connecticut, and South Carolina accounted for over 80% of the total domestic feldspar output for the year 1973.1 Pegmatites and granites constitute the major feldspar reserves of the United States, 2 and in addition, feldspar is produced as a byproduct by firms whose major products are spodumene and mica. 3 Feldspar flotation is practiced in the United States, Mexico, Finland, Norway, West Germany, Japan, and the USSR. According to the US Bureau of Mines estimates, the production of feldspar in the United States and rest of the world were 704,000 and 2,514,000 t, respectively. Feldspar is principally used as a flux in making glass, pottery, porcelain, enamel, tile, and other ceramic products. In recent years, the domestic feldspar industry is faced with a number of problems. As a result of increased cost of energy and the introduction in 1972 of new legislative programs relating to air, water, and noise pollution, land-use restrictions, and mined-land rehabilitation, the production costs have increased. Apart from the increased cost of operation, an operational problem exists with the feldspar producers in North Carolina, especially those in the Spruce Pine area. This problem is concerned with the use of hydrofluoric acid in the feldspar flotation. Feldspar producers in Spruce Pine, NC, have been discharging process waste water into the North Toe River. The mill waste water contains active fluoride ions. Fluoride in excessive concentrations is undesirable in waters used for drinking. It is stated that water containing 0.9-1.0 ppm fluoride will seldom cause mottled enamel on children's teeth; and for adults, concentrations less than 3-4 are not likely to cause endemic cumulative fluorosis and skeletal effect. Although the literature on this subject is rather confusing and inconclusive, the inference that concentrations over 4 ppm may affect bone structure is clear. According to the recent Federal Register,4 maximum fluoride level of 1.4 ppm at 79°-98°F is considered to be adequate and safe for the protection of health of the consumers. The EPA and state environmental agencies have accelerated their drive to reduce water pollution on a faster schedule. By 1977, the EPA specifications for maximum contaminant level of fluoride ions in the discharge waters of feldspar milling operatins is expected to be reduced to 2.0 ppm. The other problems of using hydrofluoric acid are the following: toxicity, hazards of handling and storage, and high cost as compared to other inorganic acids (almost 16 times the cost of sulfuric acid). In order to reduce fluoride levels in mill discharge waters, mining companies have taken the following steps: I) Recirculating a part of their mill water. Even though recirculation of mill water seems to be a novel method of reducing fluoride contamination of the discharge water, there are certain operational and handling problems. 2) Conducting research on the treatment of fluorides in mill waste water. The technology of treatment of fluoride ions has received considerable interest in the recent years. A recent research report5 estimates that the cost of fluoride ion removal to meet the present specifications in the feldspar industry is approximately $0.25/t of ore processed, and about $0.50/t of feldspar produced. At the request of the feldspar producing industries in North Carolina, the North Carolina State University (NCSU) Minerals Research Laboratory has taken up a research program directed towards overcoming the fluoride ion pollution problem. After a close study of the operational, technical, and economic aspects of feldspar flotation, it was decided to attempt to replace the conventional hydrofluoric acid process. Conventional Feldspar Flotatin Using Hydrofluoric Acid Since the inception of the feldspar flotation process using hydrofluoric acid by O'Meara2,6 the process has achieved a great commercial success. In the conventional flotation separation of feldspar-quartz, hydrofluoric acid is used to suppress quartz and activate feldspar, and a long chain amine salt (acetate or chloride) is used as a collector. The bulk of amine collectors used in current feldspar operations are applied as the water-soluble acetates of the free-base amines. These products are pastes or waxy solids which are available in a range of acetic acid neutralization levels generally 50 to 100% neutralized. In spite of the problems mentioned in connection with the use of hydrofluoric acid, this process is extremely stable with respect to changes in the process variables. With the exception of a few operations, alaskite and pegmatite are the major sources of feldspar.7 In the flotation treatment of a pegmatite that contains iron-bearing minerals (heavy minerals), mica, feldspar, and silica, a logical order of removal presents itself considering the following:8 1) Mica is readily floated by an amine collector in a pulp pH 3.5. Some iron-bearing minerals will usually respond to amine collector in acid circuit with the mica concentrate. 2) Since iron minerals tend to occur invariably in the feldspar concentrate, it is desirable to remove most of these prior to feldspar flotation. A fatty acid or a petroleum sulfonate collector used in this flotation step in acid circuit will float iron-bearing minerals. 3) Using hydrofluoric acid to maintain pH of 2.5, an amine collector employed in a final step will float feldspar away from silica, usually leaving the latter in the tailing as a high-grade silica concentrate. The problems connected with the flotation separation of feldspar-quartz arise due to the similarities in their chemical structure. Therefore, any reagent system that is likely to succeed in feldspar-quartz separation should have adsorption affinity towards one of the minerals and depression effect towards the other mineral.

Jan 1, 1979

By H. J. Beattie

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

By R. L. Stegman, M. R. Achter

R. L. Stegman and M. R. Achter (U.S. Naval Research Laboratory)—In a study of the surface structures developed in the fatigue of nickel at low strains as a function of temperature, we have obtained similar results.3 As our apparatus permits fatigue tests to be conducted in vacuo, there was no masking of the surface at high temperatures by oxidation so that the structures there could be observed directly. The relatively few broad slip bands observed at room temperature gave way at 300°C to a large number of uniformly distributed and narrower slip bands. At 550°C deformation began to concentrate around the grain boundaries and progressively increased up to 800°C. In addition fatigue strength was observed initially to increase with increasing temperature up to about 600°C due to the effectively increased ductility caused by the dispersal of fatigue damage. The fatigue strength then decreased at higher temperatures as grain boundary cracking dominates. Maria Ronay, W. H. Reimann, and W. A. Wood (authors' reply)— The authors are pleased to note that R. L. Stegman and M. R. Achter reach similar conclusions from their study of surface slip on nickel. However, they would emphasize that their own conclusions are based on what is shown by study of specimens that have been sectioned and that this study also shows that surface slip is not necessarily representative of what happens below the surface.

Jan 1, 1965

By J. O. Brittain, E. Lautenschlager

An investigation was conducted on fine grained airon wire to measure the influence of the temperature of deformation on strain aging near room temperature. Specimens were deformed various amounts at 77°, 195°, or 273°K and aged. The strain aging was followed by either internal friction or return of the yield-point measurements. The results show that strain aging occurs in three stages. During the first stage there is small, almost immediate return of the yield point. The solute carbon concentration, as mesured by internal friction, remains constant in stage I but is lower than the concentration in the unstrained condition. In the second stage, the solute concentration decreases while the magnitude of the yield point increases. In the third stage, the solute atoms continue to drain from the solution, the yield point approaches a maximum, and the strain-hardening coefficient and flow curve increase. The kinetics of the strain aging reaction are not the same for the two sets of measurements since the internal friction results lag behind the yield-point measurements. However, the strain-aging kinetics measured at 44° and 64°C showed no effect due to the difference in initial deformation temperature; nor were the strain aging kinetics influenced by low-temperature anneals at 77°, 195°, and 273°K. 1 HE object of this investigation was to measure the effect of initial deformation temperature on the strain aging of a-iron by tensile tests (i.e., return of the yield point) and internal friction methods, to correlate the results of the two measuring methods, and to measure the effect of low-temperature annealing (<273°K) after low-temperature deformation upon strain aging. The experiments were performed on fine-grained a-iron wire containing 0.02 wt pct c.l According to Thomas and Leak,&apos; return of the yield point and internal friction are similar measures of strain aging since both are dependent on solute atoms leaving the solid solution. The decrease in internal friction as a function of aging time is indicative of the removal of solute atoms from the solid solution, while the return of the yield point as a function of the aging time gives the rate of arrival of solute atoms at the dislocations. According to Cottrell and Bilby,3 during aging the solute atoms create an "atmosphere" which locks the dislocations and causes a return of the yield point on subsequent testing. It has been shown that after low-temperature neutron bombardment, a-iron goes through a stage of recovery at low temperatures which can be attributed to the annealing of iron interstitials&apos; and/or vacancies.4 If, after low-temperature deformation, there is an interaction during a low-temperature anneal between mobile point defects and the solute atoms (i.e., carbon atom interaction with vacancy or iron interstitial), it is possible that some solute atoms will be found at defect sites other than dislocations. Such changes in the sinks for the carbon atoms might be expected to alter the strain-aging kinetics sufficiently to be detected by either inter-

Jan 1, 1962

UNIVERSITY OF ALABAMA University, Ala Mining and Metalliaigical Society* G L Roberts, President T G Patterson, Vice-President B B Copeland, Treasurer K F Stark, Secretary G T Bator, Faculty Sponsor F H Crockard, Counselor

Jan 1, 1949

By Y. A. Topkaya

The placer gold occurrences at Sart Çayl, Manisa, Turkey, the legendary River Pactolus of King Croessus, were evaluated in this study to determine if this deposit contains sufficient recoverable value to justify development and exploitation. The gold occurs both in the upper Neogene conglomerates and the alluvium derived from these conglomerates. The total reserve in the whole region is estimated to be 500 million cubic metres. Samples were taken of the upper conglomerate and in the alluvium in an attempt to determine the amount and the physical nature of the gold. The gold in samples was recovered by screening out barren oversize followed by washing the sand and gravel through riffled sluices. The resulting sluice concentrate was later panned and amalgamated at site. Laboratory cyanidation testing of some samples for control purposes was also done. The average calculated free gold was found to be about 90-100mg/m3 and the size of gold flakes found was quite small. The field as well as laboratory testing of the samples of Sart Çay1 indicated that the potential reserves in this region could only be developed as a sand and gravel operation and the gold could be recovered together with the heavy minerals as a byproduct.

Jan 1, 1984

A self-appointed, committee consisting of J. Waldo Smith, Chairman, Richard S. Buck, J. J. Carty, J. Parke Channing, E. L. Corthell, Alfred Craven, Thomas Crimmins, Gano Dunn, George Gibbs, Alex. C. Humphreys, F. L. Hutchinson, Charles Warren Hunt, D. S. Jacobus, John W. Lieb, William Barclay Parsons, George H. Pegram, Charles F. Rand, Calvin W. Rice, Robert Ridgway, William L. Saunders, Merritt H. Smith, Bradley Stoughton, and William H. Wiley, organized a course of seven free lectures on military engineering, which were given by Captains Thomas M. Robins, Richard T. Coiner, Edward D. Ardery, Corps of Engineers, United States Army, and which was under direction of Major General Leonard Wood. The United Engineering Society presented, without charge, the use of the auditorium for the purpose of these lectures, but the interest proved to be more than three times as much as had been expected, and it was therefore necessary to divide the courses into three parts, one of which was given in the afternoon in the auditorium of the United Engineering Societies Building, one in the evening in the same place, and another in the evening in the auditorium of, the American Society of Civil Engineers. These lectures occurred on Mondays, from Feb. 14 to Mar. 27, 1916. The subjects and speakers were as follows: Feb. 14, 1916: Organization and Duties of Engineers in War, and what Engineers in Civil Life will be called upon to do in the Defence Of the United States. Captain Thomas M. Robins, Corps of Engineers. Feb. 21, 1916: The Service of Reconnaissance Including Surveying, Mapping and Sketching, Photography and Map Reproduction. Captain Richard T. Coiner.

Jan 5, 1916

[A Aamodt, H. C., A55 C Sales, Great Lakes Carbon Corp., 18 E. 48th St., New York, N.Y. Aamot, Olav Crone, M29 2126 M4, Galveston, Texas Aaronson, Hubert I., M47 E Prin Res Engr, Ford Motor Co., Met. Dept., Sci. Lab., Engrg. Staff, P. O. Box 2053, Dearborn, Mich. Aase, Glenn D., M54 D Prin Engr, Air Pollution Control Dist., 1480 Mission St., San Francisco 3, Calif. Abbett, W. A., Jr., M56 8629 Beverly St., Duluth 8, Minn. Abbey, Robert G., M56 138 Dartmouth Rd., Bala Cynwyd, Pa. Abbott, A. G., Jr., J52 E Test, Dev Engr, Chrysler Corp. Missile Div., P. O. Box 2628, Detroit 31, Mich. Abbott, Mark L., A58 Rep, General Refractories Co., 208 S. LaSalle St., Chicago, Ill. Abbott, W. K., J58 E Dev Met, Int&apos;l Nickel Co., Inc., 67 Wall St., New York 5, N.Y.]

Jan 1, 1961

By G. R. Speich

The precipitation of the Feab and Fe,Ti Laves phases (MgZn, type, C14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been studied in the temperature range 500" to 800°C using hardness measurements, light and electron microscopy, and X-ray and electron diffraction. The Fe-Nb alloys contained 0.96, 1.67, and 3.80 pct Nb and the Fe-Ti alloys 3.5, 5.8, and 8.8 pct Ti. In both systems only the equilibrium Laves phase is formed, with nucleation occurring at grain boundaries, at dislocations, and in the matrix. No cellular precipitation or transition phases were observed. The precipitation of the Laves phase in a fine dispersion leads to significant hardening in both systems. The hardness of the aged alloys is proportional to the reciprocal of the square root of the interparticle spacing. The maximum solid solubility of titanium in a! iron is 9.0 pct Ti at 1280°C. THE precipitation of the FezNb and FezTi Laves phases (MgZn2 type, C 14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been investigated as part of a continuing study of the mechanisms of precipitation from ferritic binary iron-base alloys. The iron-rich portions of the Fe-Nb and Fe-Ti phase diagrams are shown in Fig. l(a) and l(b). The Fe-Nb diagram is essentially that given by ansen&apos; with the more recent work of Hume-Rothery and Gibson2 added. Goldschmidt3 indicates that the FezNb Laves phase has a solubility extending from 32 to 55 wt pct Nb. The Fe-Ti diagram is also essentially that reported by Hansen.l The recent results of Nishimura and kamei, Murakami, Kimura, and Nishimura,&apos; indicate that the FezTi Laves phase has a solubility extending from 22.5 to 30.5 wt pct Ti. The L/6 + FezTi eutectic temperature of 1298°C indicated by Kornilov and oriskina&apos; has been adopted. The addition of niobium or titanium to iron lowers the 6 — y transformation temperature and raises the y — a! transformation temperature. This results in a closed y field in the Fe-Ti system, but the lower solubility of niobium in a! (6) iron results in a eutec-toid, 6 — y + FezNb, at 1200°C, and a peritectoid, y + FezNb —-a, at 989°C in the Fe-Nb system. The maximum solubility of niobium is reported to be 4.5 wt pct in 6 iron,&apos; 1.0 wt pct in y iron,7 and 1.8 wt pct in a iron.&apos; Some results from the present work indicate that the maximum solubility in a! iron is actually less than 0.96 wt pct Nb. The maximum solubility of titanium in a! (6) iron is somewhat uncertain since the early work of To faute and Butting-haus indicated a value of 6.0 wt pct while later work of Kornilov and Boriskina6 yielded a value of 14.0 wt pct. The present work indicates that the maximum solubility is actually 9.0 wt pct. In both systems the phase in equilibrium with the iron-base solid solutions is a Laves phase (Mg znztype, C14), FezNb or FezTi. Both of these Laves phases have a wide range of Solubility. The precipitation-hardening behavior of Fe-Nb or Fe-Ti alloys has not been studied extensively. Genders and Harrison&apos; reported that binary Fe-Nb alloys hardened upon aging. Peter and Fisher7 studied the mechanical properties of Fe-Nb and Fe-Ti alloys quenched from different phase fields.

Jan 1, 1962

US 4,186,083-An improved collector for use In the froth flotation beneficiation of phosphate rock, barite, fluorspar, scheelite or Iron oxide ore comprises 70 to 99.9% by weight of tall oil fatty acid or the like and the remainder a described anionic perfluorosulfonate compound. Reagent consumption is lessened, and high recovery at high grade is effected. S.S. Wang, E.L. Smith, Jr., and E. F Huliganga, assigned to American Cyanamid Co. Jan 29, 1980. 4 pp. (209-166). Filed. 12-21-77 (863,034).

Jan 1, 1982

By J. D. Raulerson, J. M. Williams

This paper presents a comparative evaluation of several system currently being used or proposed for the transport of matrix from an open-pit mine to a large fixed plant. The matrix is a sticky, wet clay to be carried from 8-16 km (3-10 miles) at 910 t/h to 1.8 kt /h (1,008-2,000 stph). The system is complicated by frequent moves of the open-pit mine site and other factors, such as use of the clay component in land reclamation.

Jan 1, 1984