Search Documents

By AIME AIME

S ULFURIC acid made in the United States during the last four years has averaged approximately 7,000,000 tons of 50" B6 acid a year. This is double the production of the year 1913. About 66 per cent of the acid is made from sulfur, 16 per cent from pyrite, 13 per cent at copper, lead, and zinc smelters, and the remainder from miscellaneous sources it her the chamber process or the contact process, (at some plants both) is used. In 1923, the contact process accounted for nearly 30 per cent of all the sulfuric acid made in this country and since then it has been increasingly employed. It was first introduced here in 1898, and has always .proved less expensive than the chamber process for the manufacture of .acid of high concentration and purity, but the latter produces acid of low strength suitable for many industries.

Jan 1, 1929

By Walter F. Bradley

CLOSE to 300 members and guests were registered at the Regional Meeting of the Institute in San Francisco. Oct. 3-6, and many other mining men were present at some of the sessions, but failed to register. Headquarters were at the Palace Hotel. Technical papers for the Metals Session were sponsored by the San Francisco Section, whereas the program for the Industrial Minerals Session was arranged by the Southern California Section. Walter W. Bradley, Chairman of the San Francisco Section, opened the General and Metals Session, introducing President Buehler, who gave a hearty welcome to those present. Clyde M. Eye, of the. Benguet Consolidated Mining Co., presented the first paper, entitled "The Economic and Strategic Value of Philippine Metals to the United States." In closing, he urged. that this country retain and control the Philippines because their large

Jan 1, 1935

By Alexander R. Troiano, Eugene P. Klier

Since the very early work on quenched structures, where the products of the martensite transformation had been recognizedl this transformation has provoked much interest and study. Theoretically it was desirable to account for the extreme changes in physical properties resulting from the formation of martensite, as that information might lead to results of practical importance. Desirable information, therefore, was on the kinetics of transformation from austenite to martensite as well as on the physical constitution of the martensite. It has been known for years that certain steels quenched to room temperature will contain persistent austenite as well as martensite. Other important and now well-established features of the martensite reaction are the Progress of the reaction on cooling only and the independence of Ar" with cooling velocities exceeding the critical velocity. These facts have been experimentally determined by various methods and investigators. Notable among the early investigators were Tammann and Scheill and Wever and Engel.2 Unfor- tunately, all investigators did not fully interpret their results, which, coupled with several investigations that yielde. conflicting resultsl caused a state of confusion that was not clarified until quite recently. X-ray investigations of martensite in steels3-6 indicate it to be a supersaturated solid solution of carbon in alpha iron. This supersaturation is evident from the appearance of a body-centered tetragonal structure with the addition of sufficient carbon. The dimensions of this tetragonal structure are a linear function of the carbon content within the limits of accuracy of the determinations. Slight tempering of tetragonal martensite leads to the destructi,, of the tetragonal structure, which is converted to a body-centered cubic strutture. This phenomenon has precipitated a controversy concerning the nature and mechanism of the tempering of martensite The facts in the case have been outlined by Epstein7 and more recently by Antia, Fletcher, and Cohen.8 The significance of Ar" on theoretical grounds is not clear, however, although considerable study has been devoted to its determination. The precise position of Art' aS a function of carbon content was first stated by Greninger and Troiano9 for steels covering a range of approximately 0.7 to 1.8 per cent carbon. The effect of alloying elements on Ar" has recently been the subject matter of investigation by various methods.

Jan 1, 1945

Oct. 8 to 13, inclusive, 1917 COMMITTEES Committee on Arrangements H. A. BUEHLER, Chairman W. E. MCCOURT, Secretary C. J. ADAM L. L. HUTCHISON VICTOR RAKOWSKY J. A. CASELTON EUGENE MCAULIFFE J. D. ROBERTSON .F. W. DEWOLF P. N. MOORE ARTHUR THACHER E. F. GOLTRA MRS. P. N. MOORE H. A. WHEELER Committee on Ladies', Entertainment MRS. PHILIP N. MOORE, Chairman MRS.. W. E. MCCOURT, Vice-Chairman MRS. D. M. ARMISTEAD MRS. R. G. HALL MRS. A. A. BONSACK . MRS. J. W. HEGELER MRS. B. F. BUSH MRS. J. N. HOUSER MRS. G. 0. CARPENTER MRS. EUGENE MCAULIFFE MRS. F. V. DESLOGE MRS. RUDOLPH PORTER MRS. F. W. DEWOLF MRS. N. P. ROOD MRS. A. W. DICKINSON MRS. ARTHUR THACHER

Jan 12, 1917

NEW MEMBERS The following list comprises the names of those persons who became members during the period of July 10, 1917, to Aug. 10, 1917. ARNOT, STANLEY L., Engr., Plymouth Cons. Gold Mines; Ltd., Plymouth, Amador Co .2 Cal. BARRETT, LESLIE PARK, Asst. Geol.... Michigan Geological Survey, Lansing, Mich. BENNIE, JOHN WILLIS Gen'l. Mgr., Shannon Copper Co., Clifton, Ariz. BRINTON, OWEN FUGATE Mgr., Admiralty Zinc Co., Quapaw, Okla. BRODERMANN, JORGE, Civil Engr., Compania Minera San Francisco, Havana,Cuba. BROWN, RICHARD HENRY JR., Sales Engr., Ingersoll Rand Co., 300 N. Broadway, St. Louis, Mo. BROWN, STANLEY Chile Exploration Co., Chuquicamata, Chile. BUDDECKE, WILLIAM A Pres., Point Milling & Mfg., Co. Mineral Point, Mo. BURGESS, GEORGE K., Physicist and Chief, Division of Metallurgy, Bureau of Standards, Washington, D. C.

Jan 9, 1917

[Appalachian Petroleum Section: Walter H. Chapman, chairman; Jean Freeland, first vice-chairman; John Galpin, second vice-chairman; Jack L. Trittipo, secretary-treasurer. Meets 4th Tues., Humphreys Restaurant, Charleston. Balcones Section: William E. Richards, chairman; William C. Miller, Jr., first vice-chairman; Brantley G. Myers, second vice-chairman; Harold Vagtborg, Jr., secretary-treasurer. Meets 4th Wed., Petroleum Center Club, San Antonio. Big Horn Basin Subsection: Donald G. Davis, chairman; B. E. Yester, vice-chairman; J. F. Keleher, vice-chairman; Samuel N. Conley, third vice-chairman; William O. Snyder, secretary; M. J. England, treasurer. Billings Petroleum Section: N. J. Matthews, chairman; Guy J. Lookabaugh, first vice-chairman; George O. Ellis, second vice-chairman; Robert L. Spottswood, secretary-treasurer. Meets 3rd Tues., Turf Penthouse.]

Jan 1, 1961

By H. B. Pulsifer

THIS paper outlines a method for rapid production of flat, granular surfaces on many of the medium hard- alloys. Grinding wheels and fabrics on wheels are not used; the purpose is accomplished by rubbing on emery papers and on fine abrasives heaped on hand boards. The advantages of chromic acid in the solutions for etching nickel and copper alloys are explained. Steels may require an additional step in the mechanical smoothing owing to the lack of an ideal etchant. Chloric acid is a. rapid etchant for steel. Thirty-six photomicrographs illustrate the steps in smoothing and the clearness with which structures can be rapidly exposed. New structures in low-carbon steels are announced. After a little practice, many materials can be finished within two or three minutes. CUPRONICKELS In the previous papers on the metallography of copper and magnesium which the author has presented to this Institute there has been an attempt to demonstrate the advantages of minimizing the mechanical work of surfacing and depending more on chemical means; the present paper continues the research into a still wider field. It is obvious that the success of a chemical method for smoothing and etching depends almost entirely on the use of a suitable reagent. The etchant must remove the surface granulations and outline the structures. A very special type of reaction between reagent and metal must be displayed. Promiscuous corrosion or the intensification of the attack about local couples -formed by impurities or components must not be in evidence. There are several reagents that etch highly polished nickel and copper alloys very well. Acidified ferric chloride solutions, concentrated and dilute nitric acid solutions, and nitric and acetic acids in acetone have -been used to good advantage for the purpose. However, if they are expected to etch rather deeply-that is, smooth as well as characterize-the results may be far from satisfactory.

Jan 1, 1928

By G. R. St. Pierre, R. D. Blackburn

Oxygen contents of' liquid-iron alloys saturated with oxides are analyzed. Minimum points observed in particular Fe-X-O systems can be predicled by a simple extension of first-order interaction methods. If minimum oxygen content occurs at N; where r is the ratio of metal to oxygen in the oxide phase. RECENTLY, wisher' reported on solubility measurements of A1203 in liquid iron at 1580°C which support the earlier work of d'Entremont, Guernsey, and chipman2 and Gokcen and Chipman. Swisher's diagram is reproduced in Fig. l. Minimum points in oxide solubilities have also been found in the Fe-Cr-0 system,4 Fig. 2, and the Fe-Ti-0 system,' Fig. 3. Minima positions can be used to confirm approximately the measured first-order interactions, &, cgr, and E&~, in liquid iron and to deduce compositions of components of constant activity in the oxide phases. Consider the solution of Alz03 in liquid iron: for which an equilibrium constant can be written as: differentiating Eq. [2] with respect to Na~, the atom fraction of &l in the metallic solution, and noting that If the activities of Al and 9 are expanded by a first-order interaction model, then:

Jan 1, 1969

By John W. Cahn

Tile avevage value of the mean curvature of surfaces in a specimen can be precisely delermined by sitrlple measurements performed on random sections or on 1 vojectiotzs of these surfaces. For surjaces enclosing particles, the quanlity is sllown to be velated to the probable tlurrrhev ot particles intevcepted by a random platne and, under certain conditions, to the perimeter of their Projected image and to the increuse in surjace area when the particles grow. Many of the velalionsl~ips are valid for any shape or size of the particles. THE recent growth of the field of stereology or quantitative microscopy is largely the result of the discovery of a limited number of rigorously defined geometrical parameters that can be precisely measured on random sections or projections of a structure without assumption about particle shape.' Such parameters have been the volume fraction and surface area and line length in a unit volume. The present paper introduces the average of the mean curvature of surfaces in a volume, and shows that it can be rigorously measured by counting methods alone. AVERAGE CURVATURE ON A PLANE Consider a curve y = v (x) on the xy plane. The curvature Kp in the plane at any point is given by Kp = (dZy/dx2)/[1 + (dy/dx)2]3/2. The average curvature along the curve may be defined as Kp = (1/L) fKpdl |1] where dl = [(dx)' + {dy)2]1/2 is the length of an element of the curve and .(dl = L is the total length of the curve. The integral on the right-hand side of Eq. [l] will be called the total curvature, It is dimensionless and readily evaluated by substituting d = arctan (dy/dx) to give ah which is the change in direction of the tangents to the ends of the curve, Fig. 1. Hence, Kp = (1/L)(?h) [2] It can also be seen that Eq. [2] is applicable in the limit of sharp corners. Even though the curvature is infinite at a corner, f Kpdl remains integrable and equal to the change of angle. The signs of the quantities Kp and dl are arbitrary and, if the areas adjoining the curve are equivalent, there seems to be no compelling reason to fix the signs. For a closed curve, however, it becomes worthwhile to use the signs to distinguish among different types of areas or phases enclosed. For such a closed curve AO = t2r and As a convention, we shall take the direction of the integration along the curve in such a way that the area or phase under consideration (henceforth called a) is kept to the left side of the curve, Fig. 1. Then Kp is positive where the curve is concave and negative where the curve is convex. For a closed curve Ad - +2n if the curve encloses a, and Ad = —2n if the curve is surrounded by a. PLANAR SECTIONS OF THREE-DIMENSIONAL STRUCTURE OF ISOLATED a PARTICLES Consider next a planar section of a microstructure containing particles of a in a matrix. We place no restriction on shape of connectedness of these particles, and begin by considering the curvature of only the boundary between a particles and matrix' Clumps of contiguous a particles are then treated as a single a particle. The two-dimensional section will show in a unit area na simple closed curves enclosing a particles and nh closed curves of holes, in-

Jan 1, 1968

By Atmaram H. Soni

A statistical study of machinability led the writer to examine existing data in regard to a thermal conductivity-mechanical properties relationship. Various functional relationships were proposed and the multiple correlation determined by statistical methods discussed in detail in the 1iterature.4 The relationship having the greatest engineering and statistical significance is discussed below. The data for cast and wrought aluminum alloys''2 have been compiled and analyzed separately. The results of these analyses are presented in Table I. The empirical equations for estimating the thermal conductivity (cal sec-' cm-I °C) are: for cast aluminum alloys K = 0.584 -0.00984/ -0.00263 Hb [1] and for wrought aluminum alloys K = 0.604 -0.00424l- 0.00170 Hb [2] where 1 and Hb are the percentage elongation and Brinell hardness number. Results of a similar analysis pertaining to stainless steel3 are also given in Table I. This empirical equation for estimating thermal conductivity (Btu per sq ft per hr per °F per in.) is K = 216.19- 1.716l - 0.0997 Hb [3] The relationship between electrical resistivity and mechanical properties was also examined for aluminum alloys using the same statistical method. These results are listed in Table II. While the situation of exact multiple correlation

Jan 1, 1965

By P. R. Sahm, T. V. Pruss

Mixtures of fine GaSb and Gds as well as preal-loyed GaSbl,As, powders were hot-pressed at 690°C and 25,000 psi. Dense alloys with compositional gradients of less than 5 pct were obtained from mixtures containing about 20 mol pct GaAs. For x < 0.2, there were increasing compositional gradients, and for x > 0.2 a GaAs-rich second phase appeared in the microstructure. Densification as well as alloying wlechanisms were enhanced by dissociation and, possibly, oxidation reactions of the powders. Densification of coarse prealloyed material, however, primarily depended on plastic flow phenomena and required temperatures just below solidus and pressures of 50,000 psi Thermal and electrical properties were measured. Although in no case was the figure of merit of melt growth materials approached closer than to within 25 pct, the better overall thermoelectric properties were found in coarse-grained, prealloyed materzals which had been compacted to near theoretical density and where grain regrowth had been induced. Similar results are believed to hold in other binary 111-V compound systems if processed under similar conditions. The densification of unalloyed GaSb powders during pressure sintering (= hot pressing) was shown to depend strongly on powder particle size.&apos; Fine powders displayed a "liquid skin effect" that enhanced compaction through the presence of liquid gallium, whereas coarse powders compacted predominantly by plastic flow. The liquid skin effect, in particular, appeared attractive for alloying GaSb with other, higher-melting, III-V compounds, and to densify these in a one-step operation. This is of special interest in the case of III-V compound alloys as the conventional techniques of melt growth or long-time annealing of powders2 is very time-consuming, especially in cases where a large separation of liquidus and solidus can be expected, such as in GaSbl alloys.2 It was felt that experimentation with this system, a particularly unfavorable example, would allow us to extrapolate to several other, more favorable, cases. Uses of Ill-V alloys are most evident in thermoelectric energy conversion devices.&apos; For this reason certain thermal and electrical properties were measured and compared to those of melt-grown material and to hot-pressed prealloyed powders. EXPERIMENTAL PROCEDURE The pressure-sintering apparatus has been previously described.&apos; Using this equipment, both powder mixtures of GaSb with GaAs and prealloyed GaSbl-,As, powders were hot-pressed. The mixtures were pre- pared from cast GaSb and melt-grown GaAs. The prealloyed material was obtained from stoichiometric melts, initially heated to 1200°C in an evacuated quartz ampoule, and then annealed in the solidus-liquidus interval. A typical annealing cycle consisted of a heating to 850°C (1 hr), extended successive annealing at 750°C (65 hr), and slow stepwise cooling (25 hr) to below solidus. The GaSb, GaAs, and GaSbl-,As, materials were ground in a vibrational mill to particle sizes below 500 . A jet mill reduced these further where necessary. Fine powders were analyzed by Coulter counting for their size distribution. Average sizes by volume were calculated from the data. Mixing of the powders, where necessary, was carried out through rapid vibrational motion. The hot-pressing operation consisted of a degassing period of 15 hr, in most cases at 690°C, followed by several hours of compression, normally 25,000 psi at 690°C for powder mixtures and 50,000 psi at 710°C for prealloyed powders. The chemical compositions were confirmed by X-ray fluorescence analysis. To estimate the degree of solid solution achieved, lattice parameters were determined and interpreted according to Vegard&apos;s rule. In addition, optical microscopy helped to correlate the relative amounts of the phases present as well as the degree of porosity to the measured density. To reveal grain boundaries, polished surfaces were etched4 with H 2 O:H 2 O:HCl = 2:l:l. In several cases microscopic concentration gradients were monitored by electron-probe analysis-. RESULTS AND DISCUSSION Alloying and Densification of GaSn-GaAs Powder Mixtures. After preliminary experiments showed that no appreciable alloying took place in mixtures of coarse GaSb (22.5 p) and fine GaAs (2.5 p) powders, hot pressing of mixtures was confined to fine powders only (3.1 and 2.4 p, respectively). Alloying and densification apparently occurred simultaneously with a grain regrowth mechanism which depended on the presence of a liquid phase.&apos; The liquid phase was provided by the dissociation of GasbS particles into liquid gallium and antimony above 555°C. This not only enhanced grain regrowth and densification, as in unalloyed GaSb,&apos; but took on additional importance here for the alloying process. Alloying was speeded up by the resulting liquid-solid interaction as compared to the very slow solid-state diffusion process normally expected at these temperatures.&apos; The results obtained with a series of powder mixtures have been compiled in Table I. It is seen that for mixtures with less than 20 mol pct GaAs, x < 0.2, the compositional ranges increased and for x > 0.2 a GaAs-rich phase and free antimony appeared in the microstructure in sizable amounts.

Jan 1, 1968

By ROY BERENTZ

MANUFACTURE is the transformation of material by the application of energy and power. The energy of a man exerted throughout a day is equivalent to about one horsepower-hour of mechanical work an amount which can be purchased for less than 2c. It is evident that manual labor is uneconomical if mechanical energy can be applied effectively, or without disproportionate expense. Since manual energy is relatively so costly, economy demands that mechanical power be employed so as to reduce the human effort connected with mining operations to a minimum. Power, like other commodities, is most efficiently produced in large quantities. Mechanical transmission, once prevailing, is being rapidly superseded by electric drive. There are many reasons for this change; such as increased production, ease and accuracy of control, convenient application, ease of moving, etc.

Jan 1, 1930

By W. J. Romanow

RECENT papers by Williams, Sherwood, and Boothby,1 Seybolt et al.2 Heikes; and Roberts4 attest to the increasing importance of the hexagonal ferromagnetic compound MnBi. Since the magnetic properties of MnBi crystals are highly anisotropic, it is useful and necessary to have appropriate aids for determining their orientations—a (00.1) standard stereographic projection and a corresponding table of crystallographic angles for this structure. The tables of crystallographic angles for the hexagonal system available in the literature5 are computed for c/a ratios greater than that of MnBi and cannot satisfactorily be used to find the crystallographic angles of MnBi. A table of angles between the crystallographic planes (HK.L) and (hk.1) was calculated for MnBi from the formula0 F=are cos Hh+Kk+ 1/2(Hk+hK) + 3/4 (a/c)2Ll/v(H2 + K2 + HK + 3/4 (a/c)2L2) (h2+ k2+hk + 3/4 (a/c)2l2) on an IBM Type 650 Magnetic Drum Data Processing machine. The lattice constants used are listed in Table I and are those determined by Willis and Rooksby7 at 20°C. More recently published values obtained by both X-ray and neutron diffraction"&apos; show no difference from these significant to the calculation. From the crystallographic angles between the basal plane (00.1) and the general plane (hk.1) in Table I, an (00.1) standard stereographic projection was made for MnBi which is shown in Fig. 1. Acknowledgments The author wishes to thank R. G. Treuting and J. N. Hobstetter for their technical assistance, and Miss D. P. Booth for programing the IBM machine for the calculations. He appreciates the opportunity to read the paper of B. W. Roberts of General Electric Co. prior to its publication. References 1H. J. Williams, R. C. Sherwood, and 0. L. Boothby: Bulletin Amer. Physical Soc., 1956 vol. 1, p. 132. 2 A. U. Seybolt, H. Hangen, B. W. Roberts, and P. Yurcisin: AIME Trans., 1956, vol. 206, p. 605: Journal oF Metals, May 1956. 3R. R. Heikes: Physical Review, 1955, vol. 99, p. 446. .B. W. Roberts: A Neutron Diffraction Study of the Structures of Manganese B.W.Roberts:ANeutronDiffractionBismuthide, Physical. Review, 1956, vol. 104, p. 607. 5 A. Taylor and S. Leber: AIME Trans., 1954, vol. 200, p. 190; JouRNal of Metals February 1954. « C. S. Barrett: Structure of Metals, 2nd Ed., p. 635. McGraw-Hill Book Co. New York and London, 1952. 7B. T. M. Willis and H. P. Rooksby: Proceedings Physical Soc., London, 1954, vol. 67B, p. 290.

Jan 1, 1958

By J. F. Abel, F. T. Lee

Subsidence is controlled by a complex com¬bination of mining and geologic factors. For example, a compilation of worldwide data shows that, as the percentage of shale in the overlying rock mass decreases and the amount of sandstone increases, the angle of draw (and the area affected by subsidence) decreases. Limestone in the over¬burden appears to cause a more than twofold decrease in the angle of draw compared to a like amount of sandstone. Increased amounts of sandstone were accompanied by a greater surface subsidence relative to the mining height. The total thickness of overburden did not appear to influence the subsidence magnitude above super-critical panels. The greater the thickness extracted, the smaller percentage of that thickness shows up at the surface as subsidence. The greater the percent of the seam extracted, the greater the subsidence reaching the surface. The maximum subsidence above room-and-pillar panels de¬pends on the pillar height and minimum width as well as the other factors listed.

Jan 1, 1984

By J. R. FINLA

THE three great war periods of recent times involving the-chief industrial, commercial, and military nations of the world have been the following: 1. Wars centering around the French Republic and Napoleon Bonaparte, .1791-1815;. involving every nation in Europe, parts of Asia Minor and *North Africa., and the United States of America. 2. Wars in Europe, Asia, and North -America beginning with the Crimean War, 1854-56, the British Empire, France, Sardinia, and Turkey against Russia; the Sepoy rebellion in India, -1857; -war of France . and Sardinia against ..Austria in Italy, .185.9; :the Taiping rebellion in China, 1861; Civil War in , America, 1861-65; French. occupation .of .M Mexico, .1863; Prussian war against :Denmark, :1864; (Prussia and Italy against Austria sand various -south German : states, 1866; :the Franco-German War, 1870.7,1.

Jan 1, 1931

By G. M. Gordon, J. W. Spretnak, R. Speiser

AT present, considerable research is being directed toward the development of high-temperature, oxidation-resistant columbium alloys. Columbium. along with molybdenum and tungsten, exhibits good high-temperature strength. Unlike molybdenum and tungsten. however. columbium does not form a volatig oxide below 1375°c.l Although the outermost oxide formed on pure columbium, Cb2O3 is stable in air at elevated temperatures, it is not of a protective nature. It is porous and voluminous, and

Jan 1, 1959

By K. R. Janowski, H. Conrad

As part of a program to establish the effect of crystal imperfections on laser output, a detailed study was made of the dislocation structure of ruby crystals obtained from varioius sources. Using KHSO4 as an etchant, a detailed mapping of the dislocation structure on the (0001) and the (1150) planes was carried out. A less extensive study was made of the rhombohedral planes. The average dislocation density on the basal plane was 1.5 to 3 x 106 cm&apos;2 and on the (1120) planes -5 x 10&apos; cm-2. Howe7!er, considerable variation existed between areas on a given plane. The subboundaries in the basal plane tended to lie along [1100] type directions while those on the (1120) plane tended to lie: a) parallel to the basal plane, b) along truces of the (1101) plane, and c) along normals to the traces of the (0001) planes. The orientations suggest that mang of the dislocations lie on the (0001), (1701), and (1150) planes A Laue back-rellection nnalysis Of c-axis wander in one crystal revealed a gradual increase in misorientation from me end of the crystal to the other, with a maximum variation of 1°35&apos;. Slight etching of a mechanically polished crystal revealed mumerous polishing scratches, suggesting the existence of a plastic flow layer. It is recognized that chromium concentration, lineage, and other crystalline imperfections play a role in the efficiency of ruby lasers.&apos; Consequently, it is desirable to establish in detail the imperfection structure of ruby crystals to be used as lasers. Some exploratory work along this line had already been done by Barnes&apos; and Dils and Martin.&apos;" How- referred to as the morphological system, as described by Kronberg.4 The Miller indices given in the present paper will be based on this morphological system. In this system, the three common growth planes are the (0001), the {1120}, and the {1101}.5 Since these planes are of high stability, it is expected that they are most suitable for study by the etch-pit technique. In the present investigation, a detailed mapping of the dislocation structure was carried out for the (0001) and the (1130) planes. A less extensive study was made of the etch-pit structure on rhombohedra1 planes. An analysis of dislocations in sapphire (the ruby host) was first made by kronberg,4 who postulated that slip on the (0001) plane occurred by motion of dislocations with Burgers vector 1/3 <1150> and that these dislocations might dissociate into quarter partials. An etch-pit technique using boiling phosphoric acid was developed by Scheuplein and Gibbs6, 7 for identifying dislocations intersecting the (0001) planes and the planes near (2021) in sapphire. Al-ford and Stephens8 were able to reveal dislocations on the (0001) and {1120} planes in sapphire and ruby by etching in fused potassium bisulfate (KHS04) at 675°C. The termini of basal dislocations [(000l), <1120>] were revealed by Palmour and Kriegel9 on {1120} and {1010} by thermally etching sapphire. Bond and Harvey10 were able to decorate dislocations in sapphire by adding 1 pet by weight of ZrO2 to the Al2O3 powder used in the growth of the crystals by the Verneuil technique and then heating the grown crystals for 4 hr at 1500°C. They found, using optical transmission microscopy, that many dislocations had straight segments which were parallel to one of the six [1120] directions in the basal plane. Single dislocation lines curved smoothly from one alignment to the other, turning through angles of 60 to 120 deg. Also observed were isolated hexagonal loops, approximately 10 µ in diameter, the sides of which lay along the same directions as did the longer dislocations. MATERIAL AND ETCHING PROCEDURE The ruby specimens used in this study (all containing approximately 0.04 pet Cr) had been obtained from four different sources: Linde Co., Meller Co., Valpey Crystal Corp., and those grown at Aerospace Corp.* For the initial phase of this study, several specimens were cut from the slab shown schematically in Fig. 1 which had previously been cut from a disk boule obtained from the Linde

Jan 1, 1964

By R. B. Moore

IN 1914 the writer and K. L. Kithil announced, through Bulletin 70 of the U. S. Bureau of Mines, that the United States possessed the largest deposits of radium-bearing ore in the world. At that time a small amount of this ore was being, mined and shipped to Europe, and one company was preparing to start the extraction and recovery of radium in this country. The importance of our carnotite deposits in Colorado and Utah up to the publication of Bulletin 70 was not, however, appreciated by anyone.. At that time the total supply of radium in the world was about 10 g., calculated as element, and when I estimated that at least 100 g. of radium element, and probably 200 g., would be produced from our carnotite deposits, there was a considerable amount of skepticism. Up to the present time almost 200 g. have come from this ore, and some writers put this figure a little higher. Uranium ore was found in the copper mines of the Union Minière du Haut-Katanga at Luiswishi in 1913. Later discoveries were made at other places in the Belgian Congo, and the Katanga ores now represent the largest supply of radium-bearing ore in the world. In fact, since 1923 very little radium has been produced from American carnotite, the Katanga ore representing practically the world&apos;s supply of. radium since that date.

Jan 1, 1930

By L. Adler

The author recently proposed a technique for handling the effect of planes of weakness on failure in geologic material.1 The technique employed an "extended" Mohr&apos;s rupture envelope, on which was superimposed a generalized three dimensional stress representation. Subsequently, the method was applied to so-called two-dimensional stress states" which were in reality degenerate three-dimensional ones. Since a two-dimensional stress solution usually refers to a plane stress condition, the terminology was confusing. The distinction between a plane stress state and a degenerate three-dimensional one is shown in Fig. 1. The solution of problems involving a generalized three-dimensional stress state is greatly aided by continual reference to the basic principle that no stress components can act on a plane, oriented as is the weakness plane, which lies outside of the weakness plane&apos;s rupture enVelope.2 This is shown in Fig. 2; and if it is also remembered that the radii of the Mohr&apos;s Circles give the orientation of such a plane, solutions are easier to follow, and perform. Sample Problem 1: Site Location (generalized three-dimensional case).&apos; Given: 1) Both rupture envelope for the solid and plane of weakness. 2) Existing principal stresses and orientations in space (?12, ?13) obtained from a stress analysis of the proposed structure. Find: Permissible orientations of the weakness plane in order to select a suitable site.

Jan 1, 1963

P. Herasymenko (New York University, New York) —The authors&apos; experiments on equilibria between water vapor and liquid synthetic slags represent a valuable contribution to our knowledge of the nature of liquid slags. They can be regarded as a proof of ionic splitting of water molecules dissolved in slags. The assumption that water dissolved in slag was com- pletely ionized was made in my report on hydrogen equilibria in steelmaking as early as 194010. In that paper, the first systematic data were given on the content of ionized hydrogen in acid and basic open-hearth slags. The paper probably escaped the notice of the authors, although they mention the articles published later by other investigators who reported erratic and

Jan 1, 1958