Search Documents

By J. R. Morison, M. P. O’Brein, J. W. Johnson, S. A. Schaaf

The force exerted by unbroken surface waves on a cylindrical object, such as a pile, which extends from the bottom upward above the wave crest, is made up of two components, namely: 1. A drag force proportional to the square of the velocity which may be represented by a drag coefficient having substantially the same value as for steady flow, and 2. A virtual mass force proportional to the horizontal component of the accelerative force exerted on the mass of water displaced by the pile. These relationships follow directly from wave theory and have been confirmed by measurements in the Fluid Mechanics Laboratory of the University of California, Berkeley. The maximum force exerted by breakers or incipient breakers is impulsive in nature, reaching a value much greater than that produced by unbroken waves but enduring for only a short time interval. This impulsive force represents the ultimate development of the accelerative force and is produced by the steep wave front and large horizontal acceleration at the front of a breaker. This impulsive force greatly exceed. the drag force computed from the particle velocities of the breaker. The reader is cautioned that these preliminary results are applicable only to single piles without bracing and are likely to be modified somewhat where multiple piles are driven, one within the influence of the other or where multiple piles are connected by submerged bracing. This paper is essentially a preliminary report submitted at this time because of the current importance of wave forces in the design of offshore structures. An extended series of additional experiments is planned for the near future. Theoretical Relationships For the sake of simplicity of treatment, the theory will be developed from the equations for waves of small amplitude. The horizontal displacement of a water particle is described by the equation 2p cosh — (d + z) H L 2pt X =----------------------sin ----- . , (1) 2 2pD T sinh------ L The horizontal component of the orbital velocity is obtained by differentiation with respect to time as 2p cosh — (d + z) pH L 2pt u = ------------------- cos— .... (2) sinh- L The acceleration of the water particles at any position is obtained by again differentiating with respect to time as 2p cosh — (d + z) 9 u -2vH L 2pt -----=----------------------------sin ----- . . (3) 3 t T2 2pd T sinh------ L where H = wave height — ft L = wave length — ft d = still water depth — ft z = depth below the still water measured negatively downward — ft. T = wave period — sec t = time — sec The force exerted on a differential section, dz, in length is pD2 s u pD 1 dF= [CM (p/4) st + Cn/2 u2] dz • • (4) where D = pile diameter — ft p = water mass density — slugs/ft3 C, = coefficient of mass C,, = coefficient of drag Substituting for a s u/s t arid u2 from Eqs. (3) and (2), the force per unit length at any position z is dF p2 pD H2 &apos; / = — [- fM sin ? ± fD cos2 ? ] . . . (5) dz 2T2 fM D fD 2pt Cm = pA/H:CD = A2;? = T [+ cos2 ? for 0 < ? < p/2 cosh— (d+z) 3p L — < o < 2p Sin L -cos2 ? for p/2 <? <3p/2 The sin 9 term (inertia) i- negative for 0 < 0 < p and positive for p < ? < 2p. Values of A and A&apos; appear in Fig. 1

Jan 1, 1950

By R. Janes, F. Everard

Pilot plant studies have been conducted on a variety of iron ores of differing composition and grain size to test their amenability to dry autogeneous grinding and dry magnetic concentration. A general description of the pilot plant and its equipment is given with particular reference to the Aerofall mill and the dry magnetic separators developed by the Ontario Research Foundation. Test results are reviewed in detail with emphasis on power consumption, mill speed, the use of ball charges, types of ores, moisture content, separator speeds, and design. In 1957 the Ontario Research Foundation installed a pilot plant (Fig. 1) for the study of dry autogenous grinding and dry magnetic concentration of iron ores. A 61/2-ft Aerofall mill was installed as the dry autogenous crushing and grinding medium. The Cavanagh fast drum and the Double Helix, two dry magnetic separators developed at Ontario Research Foundation, were also installed. Iron ore samples of 10 to 150 tons have been investigated. These ores varied widely in mineralogy and grain size. Taconite (-325 mesh), fine-grained magnetite (200 to 325 mesh), and medium-grained magnetites (65 to 150 mesh) have been treated with varying degrees of success. Lately, considerable research has also been conducted on the metamorphosed magnetite-hematite complexes of the Labrador Trough. Operational and metallurgical data have been compiled from these tests. The effects of ore type, air flow, mill speed, and ball charge on mill operation are discussed. Metallurgical data are also presented to illustrate the operation of the dry magnetic separators. PILOT PLANT DESCRIPTION Fig. 2 depicts the normal flowsheet used. Minus 6-in. ore from a vibrating feeder is fed to the 6%-ft Aerofall mill powered by a 50-hp 550-v induction motor. The main blower, a 25-hp 550-v fan rated at 7000 cfm, draws air through the mill. Finely ground ore is conveyed by the air stream to a horizontal classifier, where expansion and a change in direction cause the +I50 mesh fraction to fall onto a vibrating

Jan 1, 1962

By T. C. Poulter, B. M. Caldwell, D. E. Brink

The flash X-ray has been used more than a decade to study the configuration of the jet from a shaped charge. The high-speed, rotating-mirror smear camera has provided time-distance graphs of detonations and shock fronts in transparent materials, and the high-speed framing camera has given pictorial representations of the progress of explosive phenomena. Adequate means for measuring the paths and velocities of all parts of the shaped-charge cavity Iiner during the collapse phase have not existed heretofore. A technique enabling the single-lens framing camera to make stereoscopic photographs of the cavity liner while it is collapsing has been developed. Analysis of this photographic record gives the directions and velocities of various parts of the Iiner surface, permitting direct quantitative measurement where this has previously been impossible. Significant improvements in shnped-clrarge design are expected to result. INTRODUCTION The familiar oilwell jet perforating charge, generally referred to as a "shaped charge", is related to the Mun-roe charge first described by C. E. Munroe in 1888 and later by Neumann in 1910. It differs in construction from the Munroe charge in that its cavity is lined with some inert material (usually metal)&apos;, and it differs in performance by projecting a fast jet of dense liner material against the target instead of a stream of expanding detonation products. Fig. 1 represents a typical shaped charge in axial cross section. The charge is circularly symmetrical about its longitudinal axis. The cavity at the right is lined with metal, usually copper; and, with the exception of air, the liner is otherwise completely empty. High-explosive material is intimately in contact with the convex surface of the liner and extends in the other direction to the booster. This is a pellet of high explosive having somewhat different characteristics and serves to couple the detonator to the main charge. When the detonator is fired, a small hemispherical reaction zone of very high temperature and pressure occurs at its output end. The booster responds, adding its own latent energy to the reaction, thereby initiating the main charge. The reaction progresses throughout the main charge at a velocity of 7 to 8 mm/microsecond until all the explosive material has reacted. With a reaction pressure of about 160,000 atm, the surrounding material is moved rapidly away from the high-pressure zone. As the detonation proceeds along the cavity liner, moving from apex to edge, the liner is collapsed toward the axis of the cavity, where liner material from all parts of the concave surface converges. A zone of extraordinarily high pressure results. with only one escape path—outward along the axis. The particles from the liner, thus, become a jet of very high velocity, with a density characteristic of the material from which the liner was made. The kinetic energy of the jet, concentrated in a small area of the target, has great penetrating power. It overcomes the strength of any target, and the target material crumbles or deforms plastically to escape from the path of the jet. An unlined cavity charge, on the other hand, projects a turbulent body of hot gaseous material against a target and erodes the exposed surface. With equal quantities of explosive, the penetration effectiveness of an unlined charge is a small fraction of that of a lined charge. Given an explosive charge with a detonator at one end and an axially symmetrical metal-lined cavity at the other, one has a perforator of considerable potency. To maximize the penetrating and other desirable effects,

By E. A. von Hahn, T. R. lngraham

The rates of cementation of pd11 on electropolislzed copper cylinders were studied in aqueous perchloric acid solutions at pdII concentrations from 0.02 to 0.1 mM. The cylinders were rotated at various high speeds to reduce the diffusion layer to a minimum thickness. In 0.1 M HClO4 solutions, the cemented palladium is dense, adherent, and shiny. The rate data indicate that there are two stages in the deposition. In the initial stage, the rate of cementation is first order with respect to the pd11 concentration. The second stage is much slower. The first stage is consistent with rate control by the diffusion of pd11 ions to the copper surface, and/or chemical reaction at the surface, and the second stage is consistent with rate control by the diffusion of copper ions from the cop-per surface through the deposit of cemented palladium, out to the main body of solution. In 0.001 M HClO4 solution, only the first stage is evident and the rate is more rapid than at higher acidities. This rate enhancement is attributed to PdOH+ ions that predominate at low acidity and aye more reactive than unhydrolyzed pdII. The deposit is porous and loose. All of the cemented deposits are Pd-Cu alloys rather than pure palladium. Activation energies are 9.5 kcal per mole in 0.1 M HClO4 and 7.4 kcal per mole in 0.001 M HClO4. CEMENTATION or displacement reactions occur between aqueous solutions of metal salts and immersed metals according to the general equation: where M1 is electrochemically the more noble metal. Although these reactions find considerable application in metals recovery processes (e.g., the cementation of copper192 or gold3), in electrorefining processes (e.g., solution purification before electrolysis4,5), and in plating and metal finishing processes,6 few studies have been made of the kinetics of such reactions.7-9 The rates of cementation reactions will depend on one or more of the following factors: a) chemical reactions at the metal-solution interface; b) ionic transport to or away from the interface;&apos;-&apos; and c) the character and adherence of the cemented deposit on the substrate metal,6a,10 because the deposit will inhibit the rate of transport of dissolving ions (M2m+) into the solution. In this investigation, the kinetics of the early stages of cementation were studied to obtain an understanding of the reaction mechanism under conditions in which the deposit was sufficiently thin that its inhibiting effect could be disregarded. To achieve this, very dilute solutions in Mn+ were used. Cementation rates are often fast in the initial stages and transport-contr01led.9 To find conditions under which transport control would shift to chemical control, very high stirring velocities were used to minimize the diffusion-layer thickness. Of the many possible cementation reaction systems, the palladous perchlorate-copper system was chosen for this investigation because it was believed to involve simple ion-for-ion exchange. In addition, there are no interfering side reactions, such as the reduction of hydrogen ions, and anion effects are usually absent in perchlorate solutions. EXPERIMENTAL Materials. Reagent-grade chemicals and redistilled water were used in all experiments. Palladous perchlorate stock solutions (0.02 M) were prepared by dissolving 99.5 pct Pd sponge (Johnson Matthey and Mallory Ltd.) in concentrated nitric acid, adding concentrated perchloric acid, evaporating twice slowly (to prevent PdO precipitation) to a small volume, and diluting in a volumetric flask. To prevent gradual hydrolysis of PdII, the stock solutions were made 0.4 M in HC104. Tests for pdIV (Ref. 11) and C1- were negative. Copper strips were cut accurately from 0.025-in. electrolytic tough pitch sheet, Sample 1 (Mines Branch stock or Canadian Copper Refineries Ltd., Montreal), or from oxygen-free, high-conductivity sheet, Sample 2 (American Metal Climax O.F.H.C. brand, sold by Utility Brass and Copper Corp., Brooklyn). The strips were annealed for 1 hr at 335°C in a stream of purified nitrogen (Union Carbide, Linde Division) which had

Jan 1, 1967

By A. C. Stoddard

Early in the present century, prospect-ing was active in the area of the present Miami district. There were plenty of blue and green copper outcroppings, but very little ore of a grade that would stand shipping costs had been uncovered. Late in the first decade of the century, tunnels were driven into the north and south slopes of the Inspiration ridge, and two of them exposed disseminated copper sulphide ore. This was the original discovery of such ore on the ground of what eventually became the Inspiration Division of the consolidated company. By 1910 exploration of the ground area was well along and by 1911 underground development had been started. In the next few years a large tonnage of disseminated copper ore had been proven— sufficient to justify the expenditure of several million dollars in mine development and for mine equipment plus large sums for treatment plants. The mine and treatment plants were placed in production July 1, 1915. To Jan. I, 1945, there had been produced from the mines of the Inspiration Consoli-dated Copper Co., more than 106,000,000 tons of ore. Nearly all of this tonnage had been recovered by block caving. GeologIcal and EconomIc FActors Block caving is a mining system based on the fact that if a mass of rock has a sufficient number of fractures and planes of weakness the mass will disintegrate if the support of an area of sufficient size is taken away—that is, "undercut." If the material that caves away from the bottom of a block is drawn off the spalling is progressive. There is a limit to the speed of this spalling or caving action, which varies with the structure of the rock being caved. If the rock is drawn at a rate faster than the caving rate, and if this drawing is continued too long, a void may be created that could make a very dangerous condition if the area should drop as a block and force the air below the uncaved rock out through the raises and drifts. This can be a very destructive force. On the other hand, if the broken material is not drawn fast enough the swell of the material in place to broken material would pack the mass until it was almost solid again and could not be drawn without much blasting, or perhaps even partially undercutting again. Geologically therefore it would seem that any rock with seams and fractures would cave; but for block caving there should be enough seams and fractures in a limited area so that such an area will cave and produce a product that can be drawn safely, rapidly enough and at a cost justified by the value of the product being drawn. At the Inspiration the disseminated ores occur in two formations, the Pinal schist and the Schultze granite. There is no material difference in the grade of the ore formed in the schist and in the granite. The chief copper minerals are chalcocite, malachite, azurite and chrysocolla. Other copper minerals occur in limited quantity.

Jan 1, 1946

By J. R. Long, E. L. Anderson, R. S. Dean, F. S. Wartman

TITANIUM has been estimated to comprise about 0.65 per cent of the earth&apos;s crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, &apos;methods required for its fabrication, and the properties that may be produced in this interesting metal. METHODS OF PREPARING METALLIC TITANIUM Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,2 van Arkel,3 and Fast,4 subsequently confirmed the facts that pure titanium is a ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent &apos;solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agents2 with sufficient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By William L. Russell

A new instrument for measuring bulk and grain vol-urnes is described, and compared in accuracy with two modifications of Nutting&apos;s method, All three methods are reasonably fast, and in all three the probable error in the determinations of bulk volume can be kept down to about 0.1 to 0.2 per cent. INTRODUCTION The new pycnometer described in this paper is designed to give speed without sacrificing accuracy. Some time ago Russell1 described a somewhat similar appa-ratus; however, the instrument described in the present paper is more accurate. Nutting&apos; designed the pycnom-eter shown in Fig. 1 (A and B), and Pirson3 has shown points like those of Fig. 1-D. The procedure described in this paper for using Nutting&apos;s pycnometer has been modified from that used by Nutting. CHOICE OF LIQUIDS The best liquids for measuring grain volumes are hydrocarbons or chlorinated hydrocarbons which evaporate slowly. Trimethylbenzene or mesitylene, triethylben-zene, carbon tetrachloride, and tertalin have been used for this purpose. Any of these liquids or mercury may be used for measuring bulk volume. PREVENTING ERRORS DUE TO INVASION OF LIQUID Errors due to the invasion of the porous, permeable bulk samples by the liquid of measurement may be prevented or greatly reduced by using mercury, by applying an impervious coating, or by soaking the bulk samples in the liquid of measurement until bubbles cease issuing from them. Errors are produced only by the invasion of the samples which occurs between movement when the samples are weighed in air and the moment the weight of liquid displaced by the sample in the pycnometer is determined. No error is produced by varying degrees of filling of the pore space of the samples by the liquid of measurement. The excess liquid should be wiped from the samples immediately before the weight in air W1, is determined, and they should be placed in the pycnometers immediately. OPERATION OF NEW INSTRUMENT The new pycnometer is shown in Fig. 2. It consists of two glass parts which fit together at a ground glass joint. The spaces J and D are connected by fine glass tubes E, and the space J must be larger than the space D by at least the volume of the largest sample to be tested. The projections H afford a grip for twisting when the two parts tend to stick together. The position of the sample in mercury is shown by I, and in other liquids by M. F is a permanent mark on the glass, and G is a tem-Some marker. In order to determine the position at which G should be placed, invert the instrument so that A is at the bottom, and fill space D. Place the cub K

Jan 1, 1958

By J. Szekely, G. P. Martins

A formulation is given and a general analytical solution is presented for the problem of spherical phase growth in multicomponent systems. The results are valid for describing the rate of bubble growth in the absence of translational motion and, therefore, should be relevant to heterogeneous nucleation processes. Typical worked examples are given, which include bubble growth due to the simultaneous diffusion of hydrogen and nitrogen in molten steel, and the growth of CO bubbles in steel, due to the reaction: C + 0 = CO. The calculations predict that the presence of additional components would enhance the growth rate and also increase the absolute rate at which the individual components are transferred into the bubble. These findings should be relevant to degassing processes. THE problem of spherical bubble growth in the absence of translational motion is appropriate to the description of the heterogeneous nucleation and subsequent growth of gas bubbles while attached to a solid surface. Such problems are of considerable practical relevance to various vacuum degassing and steelmaking processes where bubble nucleation and subsequent growth play an important part in the overall reaction mechanism. A definitive formulation of spherical phase growth has been given in the now classical paper by Scriven1 and the analogous problem for solid phase growth has been discussed by Horvay,2 furthermore a thorough review of the relevant literature has also become available.3 All this previous work was concerned with one component or binary systems. The purpose of this paper is to show that the technique developed by Scriven may be generalized to alow the consideration of multicomponent systems. The results of this generalization would be particularly relevant, as gas bubble nucleation in the metallurgical systems previously mentioned frequently involves the simultaneous diffusion of several components. In the following a general formulation is given and typical worked examples are presented. FORMULATION Consider the growth of a spherical gas bubble due to diffusion in a quiescent liquid of infinite extent, as sketched in Fig. 1. The formulation of such problems requires the statement of the following conservation equations relating to the liquid phase: Equation of continuity Equation of motion Conservation of the diffusing species—Diffusion Equation. The following assumptions are made: a) The fluid is incompressible, quiescent, and of infinite extent b) The bubble is stationary, i.e., it undergoes no translational motion c) Spherical symmetry is observed throughout d) The mass diffusivity is constant e) Chemical equilibrium exists at the surface of the bubble, and any reactions occurring there are fast compared to the diffusion process f) Inertia and surface tension effects are neglected. Equations derived on the basis of these assumptions by previous investigators were found to provide a reasonable representation of bubble growth while attached to a surface in organic and aqueous systems4,5 For gas bubble growth in molten metal systems assumptions a) to d) chould hold reasonably well. The exclusion of chemical kinetics as a possible rate limiting step may not be universally valid, but should hold for many systems operating at high temperatures. The effect of hydrodynamic inertia may be neglected for moderate growth rates; finally, the assumption neglecting the effect of interfacial tension on the bubble growth was made for the sake of mathematical convenience; its inclusion would have required the use of quite cumbersome numerical techniques. While surface tension effects could be appreciable on the initial values of the overall growth rate, especially at low absolute pressures and in case of small bubbles, they are not thought to modify the relative effects present in multicomponent systems, the study of which is the objective of this paper. Within the framework of the above assumptions

Jan 1, 1970

By William T. Schneider, Taylor Cole

Drilling in West Texas during 1941 was more active than in any year since 1937, a total of 2325 wells having been drilled. Pre-Permian exploration was the greatest in the history of the area; 106 wells tested pre-Permian formations during the year. Wildcatting reached the peak since 1937, with 135 wildcats, of which 20 per cent were producers. The wells were drilled to a greater average depth than in any previous year. Slim-hole drilling was the common practice, using drilling equipment that is largely portable. Because of deeper drilling, more attention was paid to mud fluids, especially the use of materials to reduce water filtration. There has been slight improvement in the protection of the pay horizons while drilling by the use of reverse circulation, and drilling-in with oil as well as low water-filtration muds. The practice of setting and cementing the oil strings through the producing formation and perforating opposite the pay zones has increased in the fields producing from sands. It is doubtful whether this practice is of unusual value in dolomitic limestone fields. There have been few if any technological improvements in obtaining necessary information on the pay sections penetrated, by coring, core analyses, better sampling, and more detailed drilling time. However, more operators are beginning to realize the necessity of good samples. For a proper study of the reservoirs in West Texas, it is essential that better samples be obtained, that more core analyses be run, and that better methods of obtaining drilling time be initiated. It should be noted that increased drilling speeds and slim-hole drilling have tended to reduce coring and core recovery and have not aided in obtaining good subsurface samples. In fact, fast drilling speeds and slim-hole drilling have reduced the cost of drilling operations, but with the sacrifice of much needed subsurface information. Larger quantities of slower-reacting acid are being used per well. There has been improvement in shooting, in that a greater number of quarts per foot have been used and an attempt has been made to concentrate the shots opposite the pay zone. The use of mud logging to determine the characteristics of the pay section increased considerably over the year 1940. There has been a slight increase in obtaining reservoir information in the new fields, such as bottom-hole sampling, bottom-hole pressures, and records of gas, oil, and water withdrawals. However, there is great need for more data on these subjects, particularly accurate information regarding gas and water volumes. There are three repressuring projects and a fourth is nearly ready for operation in the Kermit field. There is one repressur-ing project in the Payton field and one in the North Ward field. So far, the gas-injection projects have not shown very impressive results. As yet, there are no water-flooding projects or water-disposal projects in West Texas. Not including gathering lines within the fields, 222 miles of feeder pipe lines were

Jan 1, 1942

By Taylor Cole, William T. Schneider

Drilling in West Texas during 1941 was more active than in any year since 1937, a total of 2325 wells having been drilled. Pre-Permian exploration was the greatest in the history of the area; 106 wells tested pre-Permian formations during the year. Wildcatting reached the peak since 1937, with 135 wildcats, of which 20 per cent were producers. The wells were drilled to a greater average depth than in any previous year. Slim-hole drilling was the common practice, using drilling equipment that is largely portable. Because of deeper drilling, more attention was paid to mud fluids, especially the use of materials to reduce water filtration. There has been slight improvement in the protection of the pay horizons while drilling by the use of reverse circulation, and drilling-in with oil as well as low water-filtration muds. The practice of setting and cementing the oil strings through the producing formation and perforating opposite the pay zones has increased in the fields producing from sands. It is doubtful whether this practice is of unusual value in dolomitic limestone fields. There have been few if any technological improvements in obtaining necessary information on the pay sections penetrated, by coring, core analyses, better sampling, and more detailed drilling time. However, more operators are beginning to realize the necessity of good samples. For a proper study of the reservoirs in West Texas, it is essential that better samples be obtained, that more core analyses be run, and that better methods of obtaining drilling time be initiated. It should be noted that increased drilling speeds and slim-hole drilling have tended to reduce coring and core recovery and have not aided in obtaining good subsurface samples. In fact, fast drilling speeds and slim-hole drilling have reduced the cost of drilling operations, but with the sacrifice of much needed subsurface information. Larger quantities of slower-reacting acid are being used per well. There has been improvement in shooting, in that a greater number of quarts per foot have been used and an attempt has been made to concentrate the shots opposite the pay zone. The use of mud logging to determine the characteristics of the pay section increased considerably over the year 1940. There has been a slight increase in obtaining reservoir information in the new fields, such as bottom-hole sampling, bottom-hole pressures, and records of gas, oil, and water withdrawals. However, there is great need for more data on these subjects, particularly accurate information regarding gas and water volumes. There are three repressuring projects and a fourth is nearly ready for operation in the Kermit field. There is one repressur-ing project in the Payton field and one in the North Ward field. So far, the gas-injection projects have not shown very impressive results. As yet, there are no water-flooding projects or water-disposal projects in West Texas. Not including gathering lines within the fields, 222 miles of feeder pipe lines were

Jan 1, 1942

By F. Gordon Smith

ALTHOUGH several geological indicators of the critical type are known, including quartz inversions and decomposition of hydrous minerals such as serpentine, there are very few of the general type. Solid solutions are excepted, but the limitations of use are very restricted and interpretations are sometimes ambiguous. General methods for determining temperature and pressure conditions during the crystallization of minerals would have considerable scientific and economic value. It is not the purpose of this paper .to, discuss the various methods of geological thermometry and barometry, but to present one general method, applicable to all minerals, and to describe what progress has been made in the methods of measurement. The general method, in. brief, is a study of the stress conditions in and around various types of foreign inclusions which are trapped in minerals during growth. The method depends upon the fact that any homogeneous gas, liquid, or solid will in general have coefficients of thermal expansion and volume compressibility different from those of any given mineral. Therefore stress must develop in and around all types of inclusions in minerals if the temperature or the pressure, or both, are changed from the conditions which prevailed during the growth of the mineral. The methods of measurement consist of determinations of the temperature-pressure conditions of fit of the inclusions in the host mineral. The types of inclusions in minerals are: 1-gas, or liquid plus vapor, when observed at room temperature, due to crystallization under pneumatolytic conditions; 2-liquid, or liquid plus vapor when observed at room temperature, due to crystallization under hydrothermal conditions; 3-glassy solid, or devitrified glass, due to crystallization under magmatic or high temperature metamorphic conditions, in a siliceous liquid; and 4-crystals, due to overgrowth of other minerals crystallizing simultaneously or of other minerals which crystallized previously. A survey of the literature shows that much valuable earlier work on inclusions, especially that carried out in England in the last century, has dropped out of current knowledge. The following is a brief summary of the significant, contributions to the problem up to the present day. Davy in 1822 asserted that fluid inclusions in minerals consist of an aqueous solution of salts and a gas bubble, the whole being either at lower or higher pressure than atmospheric.1 At intervals from 1823 to 1862, Brewster contributed information concerning other types of inclusion consisting of 1-aqueous solution, a much more expansible liquid, and a gas; 2-aqueous solution, salt crystals, and a gas; and 3-the very expansible liquid and a gas. The very expansible liquid fills the gas space between 20° and 30°C. Compression strain effects were seen around inclusions in diamond, topaz, and other minerals.2-6 Sorby in 1858 and 1869 further advanced the study begun by Davy, stating that fluid inclusions represent a sample of the mother liquor of crystallization and that the degree of filling of aqueous inclusions at room temperature defines the temperature-pressure relations during formation of the host. The degree of filling may be measured by determining the minimum temperature of filling of the inclusion by the liquid phase. The very expansible liquid in some fluid inclusions is liquid. carbon dioxide. The temperature at which salt crystals in fluid inclusions completely dissolve in the fluid is the minimum temperature of formation. Inclusions of glass or devitrified glass indicate crystallization from a melt. Inclusions of crystals in minerals are often centers of strain, which may be seen by optical effects or by radial tension cracks. Sorby realized that an analysis of stress-strain relations about inclusions could be used to provide precise data on the temperature of crystallization, but the matter was never pursued.7,8 Hartley (1876, 1877),9,10 Hawes (1881),11 Wright (1881),12 Johnsen (1920),13 and Holden (1925)14

Jan 1, 1952

By Carl J. McHargue

Mechanical twins were produced in electron-beam melted columbium by high-speed impact at room temperature and by slow or fast compression at -196°C. The composition plane of the twins was { 112} and the shear direction was <111>. Notches in the twin bands often corresponded to traces of {110) of the matrix and appeared to be untwinned regions. Markings within the twin bands were interpreted as resulting from {110} slip in the twins. THERE has been much work in recent years concerning plastic deformation by glide, and the dislocation theory relating to glide has reached a relatively high degree of development. On the other hand, there have been fewer studies of deformation by mechanical twinning, and understanding of this process is far from satisfactory. This method of deformation is of interest for at least two reasons. First, it provides a mechanism in addition to glide for the relief of stresses, and, in the bcc and hexagonal close-packed metals may result in significant amounts of plastic flow. Secondly, there is the possibility that twins may act as barriers for dislocation movement, resulting in pile-ups which could nucleate cracks. As might be expected, the bulk of the literature on mechanical twinning in the bcc metals is concerned with iron. A good summary of the work done prior to 1954 is contained in the book by all.&apos; Recently the refractory bcc metals have become increasingly important. Limited studies have shown that tantalum,2,3 molybdenum,4,5 vanadium,6,7 tungsten,&apos; and columbium9-11 deform by mechanical twinning under some conditions. Alloys of molybdenum with rhenium and tungsten with rhenium show extensive deformation by twinning at room temperature.I2-l4 Most of these studies have dealt primarily with mechanical properties at low temperatures or have shown the existence of twins, and there is only a small amount of information concerning the conditions under which they form. The subject of the present paper is the formation of twins under stress in columbium with a consideration of their morphology. EXPERIMENTAL PROCEDURE The material used for these studies was taken from an ingot of columbium which had been melted twice by the electron-be am-method. The analysis of the ingot was (in ppm): B < 1, C = 10, Fe < 100, The cast ingot contained very large grains, and it was possible to obtain single-crystal prisms which measured from ¼ to 3/4 in. on a side. A few experiments were conducted on polycrystalline plate which was prepared by rolling material from the same ingot at room temperature and annealing at 1000 in a dynamic vacuum of 10-6 mm Hg. This gave a plate in which the grains had an average diameter of 3 mm. After the specimens were cut from the ingot, the six faces were metallographically polished and elec-tropolished to remove all traces of cold work. Most of the observations were made on the surfaces of the deformed specirllens without further treatment. Occasionally, etching after deformation was desirable. In these cases, an etchant of the composition 50 parts H2O, 5 parts HNO3 25 parts HF, and 10 parts H2SO4 was found to delineate the twins very well. Unless considerable care was taken to ensure the removal of all disturbed metal left by the mechanical polishing, etching failed to reveal many of the features discussed in this; paper. The specimen&apos;s were deformed either by impact or slow compression at 77°K (liquid-nitrogen coolant), 198°K (dry ice and acetone coolant), and 298°K. The impact load was delivered by a hammer except in one case where the load was delivered by a bullet. Slow compression was carried out on a hydraulic testing machine equipped with a chamber to hold the coolant. EXPERIMENTAL RESULTS It has been generally believed that the conditions favoring the formation of deformation twins are large grains, low temperature, and impact loading. In fact, Barrett and Bakish2 found twins in tantalum only after impact deformation at 77°K, and Adams, Roberts, and Smallman10 observed twins in columbium only at 20 For these reasons, the initial experiments of this study used impact loading. Hammer blows caused many bands resembling twins in single crystals a.t 77" but not at 198°K. Only a few slip lines were observed on any of the single-crystal specimens of this study—essentially all the deformation occurred by twinning. The appearance of the twins on the as-deformed surface is shown in Fig. 1. Although both Figs. 1(a) and l(b) are photomicrographs of twins taken at the same magnification and from the same crystal, they are startlingly different in appearance. Fig. 1(a) was taken from the crystal face approximately perpendicular to the shear direction, whereas Fig. 1(b) was taken from

Jan 1, 1962

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. C. Dow

Belt conveyors generally are conceded to be the most economical method yet devised for the transportation of large quantities of bulk materials within plants. Belts are coming into greater use for transportation over long distances and are replacing other forms of long-haul conveyance. It is not the intent of the writer to comment on the design of belt conveyors, but to offer some suggestions for improvement in the operation of conveying belts, based on many years experience with belts in several stone-crushing plants. It is the contention of this writer that opportunities for improvement not fully realized by most operators exist in many plants and that a study of the individual conveyors can result in lower unit belt costs. General Reliability It is the fool-proof nature and general reliability of the belt conveyor that is responsible for its neglect. Even when abused, a belt will carry large tonnages and last a long time, often outlasting the personnel responsible for its care. Some operators look upon the purchase of a new belt as an expensive outlay every so many years, rather than a constant and steady cost amounting in belt wear alone to several dollars every operating day. This belt wear for all conveyors in one stone-crushing plant known by the writer costs 1 /12 cents per ton or $12 to $15 per hour, based on the present cost of belt replacements. The fact that these replacement costs are double those of prewar quality emphasizes the necessity of improving the conditions that make belts wear out. Some of those conditions are the responsibility of the conveyor designer, and if a serious original error has been made, this handicap cannot be overcome by the operator. If the belt is too narrow, too steep, or too fast for good loading, the operator finds that he has an inherently expensive belt. The other factors that decrease the life of a belt are more or less under his control. The two factors of most importance are the loading conditions and the alignment. Most of the cover wear and carcass cutting occurs at the loading point and if the alignment is not good under all conditions, edge wear or damage may result, Fig I. Loading the Belt It is difficult to load a belt in an ideal manner; that is, to flow the material on the moving belt at a steady rate, without impact, without turbulence, and with a velocity equal to and in the same direction as the belt. An inclined belt is especially difficult to load and particularly when its speed is over 300 or 350 fpm. Inclined conveyors require longer skirt plates to prevent spillage until the load settles. It does not seem reasonable to expect an inclined the to carry the same load as a horizontal belt of the same width and speed, because of the difficulty in loading

Jan 1, 1948

By M. J. Pool, P. J. Spencer, R. V. Miner

The partial molar heat of solution of rhodiunz in liquid lin and Rh-Sn alloys has been measured as a function of rhodium concentration at 700" , 725" , 750" , and 775°K. The values at infinite dilution are very exo thermic, ranging from -29,950 to -28,260 cal per g-atom Rh at 700" and 775"K, respectively. At the solubility limit the heat of solution becomes sharply nzore exothermic and has permitted the liquidus boundary to be accurately established at each temperature. From the measurements in the two-phase region of liquid Plus RhSn, the heat of formation of RhSn,has been determined. A large increase in the heat of formation between 725" and 750°K suggests the possibility of a phase transformation in this compound. V ERY few measurements have been made of the heats of solution of transition metals in liquid tin; yet those values that are available are of great interest because of their very large exothermic nature. For example, the heat of solution at infinite dilution of palladium in tin has been measured as about -26,000 cal per g-atom (625" to 800°~),&apos; while the heat of solution at infinite dilution of platinum is even more exothermic at -28,591 cal per g-atom (914°K).&apos; These values are of the same order of magnitude as the heat of formation of many intermetallic compounds and as such clearly indicate that very strong bonding must exist between the solute and tin atoms in the liquid solutions. Rhodium might be expected to display similar solution characteristics in tin in view of its close electronic resemblance to palladium and platinum. Since no thermodynamic data are available for Rh-Sn alloys, rhodium was chosen as an appropriate solute for further investigation of transition-metal systems with highly exothermic heats of solution at infinite dilution. EXPERIMENTAL The heat of solution of rhodium in dilute Rh-Sn liquid solutions was measured as a functlon of rhodium concentration at 700°, 725", 750°, and 775°K. The liquid-metal solution calorimeter used in this work has been fully described elsewhere. At the start of each series of measurements, the solvent bath consisted of about 0.5 g-atoms of 99.9+ pct pure tin. To this was made a number of small rhodium additions, about 0.0005 g-atoms each, and the heat of solution was measured for each. Rhodium of 99.9+ pct purity in powder form was used in order to promote rapid dissolution in the liquid tin. The powder specimens were contained in tin foil stated to be purified (lead-free). This foil was found to have no measurable heat of solution in pure tin so the effect of any impurities could be neglected. The energy equivalent of the calorimeter was experi- mentally determined by dropping tungsten and/or tin specimens at intervals during each series of rhodium drops. The tungsten and tin used were 99.95 and 99.999+ pct pure, respectively. The only heat effect due to a tungsten drop, or a tin drop at low rhodium concentrations in the bath, is the sensible heat of the specimen. The heat content of these materials is well-established and is presented in the compilation of Hultgren et al. 4 As the rhodium concentration in the tin bath increases a small heat effect arises from the reaction: Sn (liquid, T) — & (soln, T) where T is the temperature of the tin bath. Where necessary, this heat of solution of tin was determined by Gibbs-Duhem integration, and corrections were made to the heat effect of the tin calibration specimens and the tin foil containing the rhodium specimens. RESULTS AND DISCUSSION The calculated values of the heat of solution of rhodium in dilute Rh-Sn alloys as a function of composition are shown graphically in Fig. 1. The values have been corrected for the sensible heat of the specimens, initially at 273"K, and apply to the reaction:

Jan 1, 1969

THIS chapter and Chapter 19 deal with the heat quantities involved in open-hearth steelmaking, including the thermal efficiency of the furnace as a generator of high-temperature heat, the heat storage in the steel and slag produced and in the furnace walls, and the heats of the various chemical reactions involved in combustion, in the formation of slag, and the refining of steel. The fundamental laws to be considered are the first two laws of thermodynamics as applied to problems involving sensible and potential (or latent) heat only: 1. Heat input equals heat outflow plus storage. 2. Heat may be transferred only from a hotter body to a colder one. The first of these laws relates to the various heat quantities or the heat balance of the process. No one has as yet made an open-hearth heat balance that came out almost exactly balanced. The cause probably lies in the difficulties of accurate temperature and flow-rate measurements at the high temperatures involved and the inherent complexities in flow distribution and air leakage present in any real open-hearth furnace system. Some idea of the magnitude of the heat quantities involved can be obtained by a brief, crude outline of the heat balance of a 90-ton heat of steel. We will assume a 60 to 70 per cent hot- metal charge in a fairly fast working and only moderately efficient furnace, burning fuel oil, with a fuel consumption of around 4 million Btu per net ton of ingots produced. The time from start of charge to tap is 9 hr. During this period, the oil burned represents 360 million Btu and the sensible heat in the preheated air at the port ends is 117 million Btu, so that the total heat input at the ports is 477 million Btu. Heat stored in the steel and slag at the end of the heat, plus the various amounts absorbed by certain bath reactions, amounts to a total of 195 million Btu, but 120 million of this is supplied by the heat in the hot metal and by various heat-evolving reactions in the bath,

Jan 1, 1964

By H. Merton Ruth

THE northern anthracite fields, although facing the same economic problems as the southern fields, are confronted with the additional problem of fast dwindling reserves of anthracite which can be conventionally and economically won. The mining of coal which remains in thin beds and the recovery of pillars from areas heretofore considered unrecoverable, either by reason of cost or surface restriction, pose problems of increasing importance to the economic life of the northern field operations. Successful approaches have been made to this problem and other work is being performed that holds promise. There exists in the northern anthracite field millions of tons of solid coal, the recovery of which has not been too successful due to the following inherent operating faults: inability to concentrate producing areas, the great quantities of rock to be cut and handled, lack of consideration of proper sequence and speed of second mining, and the continued use of the mine car as the basis of payment. A mining system that has successfully solved these major problems has been in operation in the Scranton area since 1944. Over 1% million tons have been produced from veins varying from 3 to 4% ft thick by this method, which is known as the multiple panel-triangular system-conveyor mining.

Jan 7, 1950

By Eric Jette

IN order to control a chemical process by other than empirical, rule of thumb methods, two types of knowledge concerning the reactions involved must be available: (1) the thermodynamics of the reactions, and (2), by no means less important for efficient operation, the mechanisms and kinetics of the reactions. Information on the thermodynamic side enables the operator to decide upon initial and final conditions, whether heat must be .added or removed from the system, whether the reactions proceed farthest in the desired direction at high pressure or low, etc. Knowledge of the mechanisms involves the determination of the individual steps by which an initial set of reactants, under given conditions, proceed to give the desired final products and kinetic studies upon which the mechanisms are based give the speed at which each of these reactions or steps take place. Thus thermodynamic studies of a &apos;reaction enable the operator to control the direction and extent to which the reaction can proceed, while kinetic studies enable him to control rates and thus the time&apos; efficiency of the operations. The thermodynamics set the limit to which the reacting system approaches; the kinetics tell how fast the system actually approaches this limit. The two types of information are complementary and not antagonistic even though in discussing the mechanism the introduction of thermodynamics is entirely needless and generally of no assistance, while in thermodynamic studies mechanism need not even be mentioned.

Jan 1, 1931

By E. L. Anderson, J. R. Long, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth&apos;s crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By J. R. Long, E. L. Anderson, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth&apos;s crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946