Search Documents

For handling rough rock, the shovel-train system is unexcelled. The ideal application is a physically large, but not excessively deep, open-pit mine from which the coarsely blasted ore and waste must be transported distances in excess of three miles. If, in addition, a high production rate is to be maintained, railroad haulage will probably afford a lower cost per ton transportation than will any other haulage method. Relatively gentle grades must be employed- usually 3% for uphill hauls and 4% for downhill hauls. The greater the differences in elevation the greater are the railroad track grade space requirements. By way of illustration, a 3% ramp out of a pit only 300 ft deep must be almost two miles long. Mainline track locations should be selected carefully so that the frequency of movements during the life of the mining operation is minimized. This applies both to ore and to waste haulageways. Such moves are not only expensive but difficult to execute without adversely affecting production rates. The large mine affords greater opportunities for judicious location of semi-permanent trackage.

Jan 10, 1967

By Ralph H. Sweetser

BENEFICIATION of iron ores from the blast-furnace point of view means more than the usual enrichment of the iron contents by the removal of a large part of the clay, carbonic acid gas, silica, or moisture of the natural ore; it includes all these, but it also embraces several other mechanical .processes made , necessary by the exacting requirements of present-day blast-furnace practice. The increasing use of iron- bearing by-products, to as much as a third or more of the total ore burden, has introduced still another series of processes for improving the blast-furnace ore burden. As we look back over the past three decades of blast- furnace practice 'in. this country, we see that many of the blast-furnace troubles were directly due to lack of proper preparation of the iron ore burden,, and we realize that beneficiation in one form or another would have remedied the trouble. This was particularly true in the smelting of magnetic iron ores, where run-of- mine ore included such big lumps of 'magnetite along with rich fines that the furnace operations were greatly retarded and control of the furnace such as is usual today, was completely unknown.

Jan 1, 1930

By Samuel B. Christy

Columbia College has the honor of founding the first well-organized School of Mines in America. The University of Michigan, however, shared with her the honor of graduating the first class, in 1867. Prof. Thomas Egleston was the pioneer in the new movement. He drew up the original plan for the Columbia School of Mines in 1863, and was in 1864 appointed its first professor. The Massachusetts Institute of Technology turned out a class of mining students a year later, and others followed in the order of their first graduating class, as shown in Table I., condensed from the Engineering News of August 11, 1892. Besides those mentioned, mining schools have been organized in the States of Arizona and Nevada, and more or less instruction is advertised in connection with other engineering schools. It will be noticed that Columbia easily heads the list with reference to the number of graduates; the Massachusetts Institute of Technology stands second ; the California University third, and then follow Lehigh, Washington University, the University of Michigan, Lafayette College, Michigan Mining School, Missouri, Colorado and the others. The total number of graduates from these 16 schools in 26 years, has been 871, or an average of 33 per year; but as all these schools give a partial education to many who do not graduate, it is probable that from 2000 to 3000 mining students have received from them considerable training. An interesting comparison of the rate of growth of the engineering schools has been recently instituted by the Engineering News, for the period between 1860 and 1892. Table 11. shows that civil engineering had the advantage in numbers from the start, and maintained the advantage until 2890, when it was surpassed by mechanical engineering. The development of the latter course may be said to date from 1880. There are many interesting facts evident in Table 11. It will

Jan 1, 1894

By C. R. Keyes

Discussion of the paper of C. R. Keyes, presented at the Chattanooga meeting, October, 190S, Bulletin No. 26, February, 1909, pp. 119 to 166. E. R. BUCKLEY, Flat River, Mo. (communication to the Secretary*) :-Some statements in the paper of Mr. Keyes relative to the nature and formation of the Ozark lead- and zinc-deposits seem to me erroneous and misleading, and I respectfully present the following criticisms, placing Mr. Keyes's original statements in quotations. Referring to the Ozark dome: (P. 127.) "It is a region that has been repeatedly upraised and planed off, until in the middle portion the oldest known' rocks only are exposed." Does he mean that the St. Francois mountains, which have always been considered as lying on the eastern flank of the Ozark dome, are the middle of the dome? Or does he mean that the Cambrian rocks of the generally-accepted middle are the oldest known rocks ? Certainly not the latter, and if the former, his idea of the middle of the dome is not in accord with that of others who are familiar with the region. (P. 138.) " . . . the ore-deposits are definitely associated with, or localized by, geologic structures of some kind that .produce in effect basins in which' the underground waters are impounded, or their flow retarded." This statement does not appear to be altogether consistent with the facts, since the ore- bodies of the Joplin district, as the rule, occur in those parts of the Mississippian formation which have a tendency to accel¬erate the flow of ground-water rather than retard it. I might name the open, breeciated ground near Joplin, Webb City, and Oronogo as especially noteworthy illustrations. The ore-bodies, everywhere, occur in positions where there must have been a free and copious circulation of dilute lead- and zinc-solutions in the presence of reducing constituents. The inequalities in the distribution of the ore-deposits are

Oct 1, 1909

By P. Bandopadhyay, T. C. Rao

Geologically the Indian coals belong to Gondwana formations. Being of drift origin, these coals contain high percentage of mineral matter distributed in finely disseminated form. Indian coal-preparation plants process prime coking and medium coking coals for use in steel plants. Limited resources of good quality coking coals (Table 1) could not keep pace with the rapid developments of the iron and steel industry in India. This resulted in the introduction of coal-preparation technology and the establishment of washeries in India in the last 30 years or so. The first four washeries were set up during the early fifties at West-Bokaro, Jamadoba, Lodna and Kargali. Next came the first non-coking coal washery at Nowrozabad set up by the Associated Cement Company. In 1961, following the recommendation of Central Coal Washeries Committee (1953-54), Hindustan Steel Ltd. had set up five central washeries at appropriate locations, viz Durgapur, Dugda (2 washeries), Patherdih and Bhojudih, so that the raw coal feed having similar washability characteristics can conveniently come from a number of collieries to a particular washery. Subsequently, to meet the increasing demand of metallurgical coal by steel plants, two more central washeries (at Durgapur and Chasnala) and three pit-head washeries (at Kathara, Swang and Gidi) were installed by 1970. The prime objective of washing Indian coking coal is essentially to reduce the ash content. All the washeries in India, taken together have an installed capacity of about 26 million tons of raw coal input per annum. Details of these washeries in respect of their annual capacity, main washing systems adopted and the nature and size of the products are given in Table 2. It can be observed from this table that (1) bulk of the coal is processed in units like jigs HM baths and HM cyclones; (2) only two of the washeries have cleaning circuits for treatment of fines.

Jan 1, 1980

By R. J. Mechin

Top-slicing was introduced in the Pachuca district in 1917 by T. C. Baker, at that time mine superintendent of the Santa Gertmdis mine. There then existed 1200 ft. below the surface, lying between the fourteenth and eighteenth levels (a vertical distance of 354.2 ft.) a block of ore having a length of 295 ft. and an average width of 82 ft. and dipping at an angle of 65°. This block lay in the hanging wall of the vein and consisted of highly altered and fractured andesite, cut through with mineralized quartz stringers. On the foot-wall side, 26 ft. of old filling, left by former operators, was of payable grade. Stoping therein was first undertaken by the square-set filling system, but because of the extremely heavy hanging wall and loose dry filling in the foot wall, all square setting had to be accompanied by spiling, which made the operation exceedingly slow and costly. A system of mining was sought that would eliminate the difficulties inherent to the square-set system in heavy ground and that at the same time would effect the desired economies in mining. After several years, top-slicing has met all the conditions most satisfactorily, so that when similar conditions presented themselves in El Bordo mine, this method was adopted with necessary modifications. El Bordo mine is operated by the Santa Gertrudis company, and is situated about two miles north of Pachuca. Because of the diversity of the orebodies, a number of different mining methods are in use, among them top-slicing. Description of Block of Ore Former operators, when mining the original vein, left in the foot wall ore of too low grade to be profitable at the time; also, considerabe low-grade material was sorted out and stored as filling in the stopes. Some pillars were left in place, either for support or because they were not payable. All this has formed a body of ore that can now be exploited

Jan 1, 1925

By R. B. G. Yeo

Pronounced isothermal martensite formation at room temperature was measured dilatometrically in a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pctAl, 2.58 pct Ti and 0.25 pct Cb. It is shown that martensite will form isothermally if stabilization of the austenite-martensite transformation is eliminated by removal of carbon. The decarburization of two iron-nickel alloys allows isothermal transformation to martensite to occur at temperatures above their athermal Ms temperatures. In an Fe-22.4 pct Ni alloy, at the 0.008 pct C level, the Ms temperature during air cooling is 85°F higher than that during- water quenching-. At the 0.15 pct C level this difference is reduced to only 5°F. The introduction of carbon causes stabilization during air cooling which lowers the Ms temperature virtually to the same level as determined during mate?. quenching. Thus in the 0.15 pct C alloy, the Ms temperature is almost independent of cooling rate. It is suggested that rival theories of martensite formation should be reexamined in alloys of sufficiently low carbon and nitrogen content to eliminate the complication of stabilization. The Ms temperature of a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pct Al, 1.58 pct Ti and 0.15 pct Cb, solution treated at 1500°F and air cooled as 1/8-in. diam specimens, was found to be 57 °F. 1 However, when held for several hours at room temperature the steel hardened slightly and became appreciably ferromagnetic. Isothermal transformation to martensite was first revealed by Kurdjumov and Maksimova2 in an iron-base alloy containing 0.6 pct C, 6.0 pct Mn and 2 pct Cu. Most of the other studies of isothermal martensite have also been confined to highly alloyed steels which transform at subzero temperatures; for instance, DasGupta and Lement, 3 Cech and Hollomon, 4 Machlin and Cohen,5 Shih, Averbach, and Cohen.6 Averbach and cohen7 noted a rapidly decaying volume increase at room temperature in a steel containing 1 pct C, 1.5 pct Cr and 0.2 pct V. cina8 and Marshall, Perry, and Harpster9 have described the isothermal transformation to martensite at room and subzero temperature in stainless steels. Kurdjumov10 has recently reviewed the subject, noting that the isothermal formation of martensite can be observed only in the temperature range somewhat below Ms or below -50°C. The isothermal formation of martensite may be characterized as follows: 1) It occurs in steels of widely different compositions, the main prerequisite being a low transformation temperature. 2) The transformation occurs by the formation of new plates and not by the growth of old ones. 3) The isothermal transformation is suppresed by stabilization during slow cooling or holding at temperatures near room temperature. However, the factors governing this mode of transformation are still not fully understood. The formation of martensite isothermally suggests an activated process. The early theories of martensite formation did, in fact, utilize classical nucleation concepts. Kurdjumov 11 first proposed the presence of thermally activated nuclei of different sizes and compositions which would grow if they reached critical size during cooling. This treatment was enlarged and developed quantitatively by Fisher, Holloman, and Turnbull12,13 and was later reviewed by the latter two authors.14 Fisher15 associates Ms with a nucleation rate of one per cc per sec. At slightly higher temperatures the nucleation rate is so low that isothermal formation of martensite is not observed in reasonable times. At slightly lower temperatures the nucleation rate is so high that it could not be suppressed by rapid cooling. By judicious use of parameters Fisher 16 was able to obtain good agreement between classical nucleation theory and the incubation times of martensite formation.4 However the application of these principles to martensite formation in iron-nickel alloys15 predicts that an alloy containing about 30 pct (31 at. pet) Ni would not transform. The presence of an Ms temperature at -223° C in an alloy containing 34.1 pct (33 at. pct) Ni led Kaufman and cohen17 to reject the hypothesis of homogeneous nucleation in favor of the reaction path theory originally proposed by Cohen, Machlin and Paranjpe.18 This theory conveniently explains the formation of martensite athermally but becomes labored when dealing with isothermal formation. Kaufman and cohen19 did explain the isothermal activation of embryos by assuming it to be a result of the expansion of their boundary dislocation loops but this treatment predicts an upper temperature limit of isothermal martensite formation.

Jan 1, 1962

By V. R. Garfias

Principal events in petroleum operations of Mexico during 1934 have been the completion of three producing wells in the Poza Rica area and the plans for the expansion of operations of the Cia. de Petroleos de Mexico, S.A. (Petromex). Production for 1934 is estimated at close to 38,000,000 bbl., an increase of 4,000,000 bbl. over the previous year; an increase due in large part to the successful development in Poza Rica. The output of the South fields (Golden Lane) and Tehuantepec fields also increased somewhat during the year. Production of natural gasoline increased from 382,000 to 431,000 bbl. in 1934. Crude run in local refineries is estimated at 26,000,000bbl., some4,000,000bbl. more than the previous year. Exclusive of bunker fuel exports totaled 24,000,000 bbl., or 3,000,000 more than in 1933. Domestic consumption increased approximately 500,000,bbl. during the year, reaching a total of close to 13,600,000 bbl., exclusive of ships' bunkers. A total of 148 wells were completed as compared to 91 in 1933 and 40 in 1932. In proven areas, 133 completions resulted in 54 producers and 79 failures. The 15 wildcats drilled during 1934 gave no encouraging results. Seven of these were located in the border zone of northeastern Mexico; three tested possible northeast extensions of the Northern fields; two were drilled for possible extensions of the "Golden Lane" and three were completed in the Isthmus of Tehuantepec. Fields Northern Fields (Heavy Oil District).—There were 34 producing wells and 71 failures completed in the Northern fields, as compared to 20 producers and 20 failures in 1933. Practically all new producers were drilled to the shallower San Felipe formation, while wells drilled to the deeper Tamasopo limestone encountered salt water. Production of the field totaled 11,890,000 bbl., a decrease of 7.5 per cent from the previous year. Acid treatment was attempted during the year in seven wells

Jan 1, 1935

By Graham Bright

T HE chairman of the Mines Committee of the A. 1: E. E. for 1920-21 has had the honor of being also the chairman of a similar committee, the Mine Equipment Committee, of the A. I. M. E. It has been the endeavor during the past year to have the two committees work together since the object of these committees is very much the same. A meeting of the committees was held in Chicago in November of 1920, at which time it was decided that one of the best ways to work together would be to foster joint meetings of the local sections of the A. I. E. E. and A. I. M. E. By these meetings, it was hoped that various engineers in the local sections interested in mining subjects could be brought together and not only become better acquainted but be greatly benefited by the interchange of ideas and by the discussion of papers presented on mining subjects.

Jan 1, 1921

By R. G. Schaal

The Magma Mine at Superior, Arizona had an unimpressive beginning as a. worked out silver mine that was purchased in 1910 for $130,000 and then incorporated into the Magma Copper Company which has been continuously mining the deposit since 1915. Copper is the principal metal produced. However, zinc, gold, silver and iron have also contributed to the total metal product. Prior to 1973, the production rate of 1500 tons per day was maintained by hoisting 4 and 5 ton pay-loads at speeds up to 1100 FPM through four small hoisting shafts. The hoists used included 8' and 7' diameter double drum, double clutched doc. and a.c. motor driven geared units built as early as 1917. One old timer that did yoeman's service for many years was an 8' Bollen Pulley with a.c. geared drive that utilized an endless rope system with mechanical grip and release mechanism built into the pulley's throat. Primary power for all of these old production hoists was 25 Hertz. Exploration that was completed in 1967 developed a reserve of 10 Million tons of 5 per cent copper which was sufficient to justify new capital expenditures for enlargement of productive facilities to 3300 tons per day. To reach the new reserves a 22' I.D. concrete lined vertical shaft was sunk to an initial depth of 48431. A 12 ½ diameter adit was bored from the mill side of the mountain to intercept the shaft at a point about 1100' below the collar. This 9200' long adit provides the right-of-way for the mine to mill railway and egress for heavy supplies from rail head as well as a conduit for potable water, electric power, compressed air and mine drainage. Mine operating levels begin 3582' below collar and thereafter have been cut at 100' vertical intervals. Skip loading stations have been installed 4282' and 46821 below collar with an in-shaft skip dump station located 800' below collar. This provides for 4500 tons of storage above the mine to mill train loading station located 1100' below collar. Ore and waste are moved horizontally from stope chutes and drift headings by rail haulage to transfer raises which channel all material to the two mentioned skip loading stations. The 22' diameter shaft crossection is arranged with the two skip compartments on the south side separated from the manway and utility compartments by the cage compartment. The cage counterweight operates in a portion of the southwest quadrant of the shaft. The hoisting plant consists of two conventional Nordberg double drum, single clutch, geared, d.c. motor driven units that are identical except for the drives and automatic controls. The drums are 15' diameter x 105" face with LeBus grooving for 2-1/8" diameter wire rope wound in three layers. Mechanical design emp1o::ed is the same as has been used for the past twenty- five years. One drum is attached to the main shaft by 2 large bolted integral shaft flenge. The loose drum is engaged by a 4-arm positive tooth clutch meshing with radially cut teeth of the clutch ring which is bolted to the drum. The drums are one-piece steel plate weldments having a finished weight of 60 tons each and are mounted upon a 36" diameter shaft that also weighs 60 tons. With the addition of brake rings, clutch, bull gear and rope, the total dead weight adds up to nearly 250 tons that is supported by just three double row spherical roller pillow block bearings. There is no bearing between the drums. All pinion shafts as veil as all head sheave journals are supported in the same type of antifriction bearings.

Jan 1, 1975

By Samuel Wyer

Over 8,000,000 people in the United States depend on natural gas for their cooking, heating and lighting service. This service has been made possible only by the investment of large amounts of capital in transportation lines connecting the gas wells to the various communities, thus combining a hazardous mining operation with a public utility service. The effect that making these lines " common carriers" will have on the present and future service to these 8,000,000 or more people is of far reaching ethical and economic importance, and deserves careful consideration. As an introduction, it must be conceded that: 1. Natural gas, although a mineral and obtained by a mining operation-with more uncontrollable and uncertain features to cope with than exist in the mining of coal or other minerals-when served to the public becomes a public utility service. 2. The governmental power to regulate all public utilities in the interests of the public cannot be successfully disputed. 3. Mere suggestion of inconvenience to the utility is wholly irrelevant, as it cannot be considered or allowed to influence in making a defense against governmental regulation. Unfortunately it is not generally appreciated that: 1. Legislative enactments are not necessarily laws, and cannot abrogate economic laws or alter engineering facts. 2. There is a clear distinction between "common carrier" and "public utility," although the terms are frequently confused. ' "A common carrier is one who undertakes for hire to transport persons or goods, or both, from place to place for all persons indifferently, the term implying indifference as to whom shall be served, and an equal readiness to serve all who apply, in the order of their application." On the other hand, property becomes a "public utility" only "when for a particular purpose the public have a right to resort to the premises and make use of them."

Jan 5, 1914

By E. D. Gardner

IN 1947 the metal-mining industry . passed through a year of readjustment; catching up on development work has caused production to suffer. Skilled labor has been short in most mining districts, notwithstanding the highest wage rate paid in the history of the industry. The trend has continued toward increased mechanization and refinements in practices and methods to increase the tons produced per man-shift. Improvements in procedures, however, have not kept pace with rising labor rates; and, in general, labor costs per ton mined have steadily increased since the war years. Prices of base metals have been the highest in a generation, but most producing companies can afford to pay the high wages. Capital expenditures have been approved for improvements to increase the output per man, both to reduce unit labor costs and to increase output. Surveys indicate a continuing

Jan 1, 1948

By Oswald J. Heinrich

This question having been repeatedly raised, and particularly revived in a discussion at the last meeting of the Institute, I beg to submit the following remarks, based partly upon personal experience, partly upon the results of large works in Europe, establishing, years ago, the practicability of certain methods, which may therefore be considered to have passed the stage of mere experiment. Before entering upon the merits of one system or the other, it is indispensable to lay down some recognized principles, which ought to serve as guides, in arriving at fair judgments in questions of this character. In a profession like that of mining, locally so much influenced by combinations of circumstances too various to mention, it is difficult to do more than lay down the main features of a system based upon general laws and recognized facts, leaving the details to the sound judgment and experience of the engineer, who, by virtue of his education, ought to be able to make such choice and such modifications in the plans of a mine as the particular case demands. Mineral resources, in some countries the sole property of the owner of the soil, in others controlled by the strong hand of a government, are nevertheless a gift of nature, in which, indirectly, the whole of the human race has as real an interest as the immediate owner himself. This interest requires, at least, that no unnecessary waste of

By Bruce A. Kennedy

The place of the young engineer in the mining industry has been the subject of a large number of keynote addresses, magazine articles, and papers in the past year. One of the best of these was the keynote address given by Mr. J. C. Kinnear, Jr. at the Fifth Annual Intermountain Minerals Conference in Vail. Colorado. Mr. Kinnear presented as part of his address the statistics of a Canadian survey Instigated to find out why young engineers and geologists are leaving the mining industry. The results of the survey showed four main reasons for leaving: 1) insufficient money 2) slow promotion 3) lack of association with senior engineers, as well as insufficient opportunity to keep abreast of technological development 4) geographic isolation

Jan 1, 1970

By J. J. Beeson

For the past fifty years or more, the structural features of the Cordil-leran mountain system of western United States have presented some most interesting problems. Any geologist or engineer living in this region, or even making occasional examinations of the mines, will lose much of interest and importance if he is not familiar with the literature. Some of the greatest works on geology have been the result of studies carried on in sections of this region. Among the more important of the earlier works are those of Dutton,l King,2 Gilbert3 and Powell;4 of the more recent Lindgren,5 Ransome,6 Spurr,7 Butler8 and others have contributed much. Many of the papers are largely of scientific interest but even these lay the foundation for the commercial application of the broader features of the geology. I have read many of these works with the keenest interest and pleasure; in fact, some have been read until some of the more important findings seem to be my own. In this paper, however, it is my aim to accept credit for little more than the labor of assembling some of the ideas of others. This is done with the hope that an interesting and valuable discussion will be the result. If some of the ideas presented should

Jan 1, 1927

By Harold F. Unger, Byron S. Snowden, William H. Engelmann

The effects of using surfactant solutions while diamond drilling in amygdaloidal basalt of the Upper Michigan copper mining district were investigated. Nonionic, anionic, and cationic surfactant solutions, all biodegradable, were tested with size AX surface-set bits mounted on a drill instrumented for continuous recording of thrust, rotational speed, and torque levels. Water flow and penetrations rates were also recorded. A drilling study was carried out, testing two rotational speed levels, two diamond bit grade levels, and four flushing agents (including water as a control). Comparison of all low-speed/high-thrust groups of tests shows that the non-ionic surfactant produced a 35% overall average increase in penetration rate over water, the anionic a 29% increase, and the cationic a 28% increase. These increases in, penetration rates resulted in a 22 to 26% reduction in cost over flushing with water alone. With the high-speed/low-thrust combination, the surfactants produced less benefits in penetration rate increases over water (14% increase for nonionic, 14% decrease for anionic, and 2% decrease for cationic type). Particle size analyses were run on drill cuttings produced by the three surfactant solutions and by water. All surfactant solutions showed a 20 to 50% increase in solids content over that of water alone. Since flushing rates were constant, these increases in solids content agree well with the penetration rate changes. The diamonds were recovered from each bit by matrix dissolution, and bit wear was measured in terms of total loss of weight. Flushing with surfactant solutions showed a savings in bit wear in most cases. The drill team noted also that surfactant flushing improved recovery of drill core by allowing easier removal of the core from the barrel.

Jan 1, 1976

By Horace R. Graham

CHEMICAL nitrogen and the "nitrates" of commercial significance are derived mainly from three basic sources: (1) the natural deposits in the form of nitrate-bearing earth and clay, which, being largely water-soluble, can exist only in the most arid portions of the earth; (2) coal, which yields not only nitrogen but also the additional by-product hydrogen required for the synthesis of ammonia and its compounds; (3) the atmospheric air, which contains 75.5 pct by weight of pure nitrogen gas. NATURAL NITRATE DEPOSITS Occurrence Although natural nitrate deposits consisting principally of the salts of sodium and potassium have been reported in Egypt, South Africa, Mexico, Argentina, Colombia, Peru and the USA, the only known natural nitrate resources of commercial importance are the vast deposits found in the Atacama, Tarapaca and Antofagasta regions of northern Chile, lying in a narrow strip 10 to 50 miles wide and roughly 450 miles long, between latitudes [19O] and [26OS]. In addition to yielding nitrates of sodium and potassium, these deposits are the source of the major portion of the world's supply of iodine. The nitrate-bearing ores known in Chile as caliche are variable in composition and may contain from 5 to 30 pct each of nitrate, chloride and sulphate. While the deposits are present chiefly in the form of the sodium salt, potassium, magnesium and calcium also occur in percent- ages from 0.1 to 5; usually as double salts with sulphate, which are but slightly soluble in nitrate leach solutions. These double salts are bloedite(Na2S04.MgS04.4H,0), glauberite (Na2S04.CaS04), polyhalite (K2SO4.- MgS04.2CaS04.2H20). Some deposits contain up to30 pct of their ni-

Jan 1, 1949

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

By J. C. Reed, J. M. Hansell

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935

Cinnabar was discovered in southwestern Arkansas on Little Missouri River in sec. 1, T.7S., R.26W., in April, 1930, and near Antoine Creek in sec. 28, T.6S., R.23W., some 15 miles farther east in May of the same year. It was not, however, until June, 1931, that cinnabar was identified as such in a specimen from the original discovery area sent to W. M. Weigell by Walter F. Hintze of Murfreesboro. Almost simultaneously2, in July, 1931, Moritz Norden of Hot Springs identified specimens from the Antoine Creek area as cinnabar. Immediate interest in the district followed the identification of cinnabar and by January, 1932, the district was known to extend as a mineralized belt about one mile wide trending east-northeast from sec. 13, T.7S., R.27W., in Howard County across central Pike County and into Clark County to sec. 19, T.6S., R.23W., thence extending southeast into sections 33 and 34 of the same township. Since then, cinnabar has been found in sec. 6, T.7S., R.22W., thus giving a total east-west length to the district of approximately 30 miles. Interest focused mainly on the two discovery areas, with the result that mining development has progressed most rapidly in those localities. In the Antoine Creek area the Arkansas Quicksilver Co. has done considerable exploration work and has retorted the high-grade ore so obtained. In the Little Missouri area the Southwestern Quicksilver Co. has had a 12-ton rotary furnace in more or less continuous operation since April, 1932, and has been the largest producer in the district. In March, 1934, the United States Geological Survey began a study of the Arkansas quicksilver district, which was made possible by an allotment of funds from the Public Works Administration. Until

Jan 1, 1935