Search Documents

By W. J. Taylor

It is, perhaps, more important to put on record the particulars of experiments that are derided failures than those that are successful, as those of the latter class are certain to live, while the former may be lost sight of in a short time, and repeated by others. TO this end, I propose to give the particulars of a straight or no-bosh furnace just tried at the Chester (New Jersey) works, which was such a decided failure as to leave no doubt of the plan being wrong, and determining the necessity of a bosh of some kind, as of old. Some experiences during the past year led me to suppose that the bosh or belly of a furnace was unnecessary, and that the contraction of the walls toward the bottom for the stock to wedge in, in its descent, facilitated dirty walls and scaffolding; hence, irregularity and high fuel. I concluded, however, that a very shallow bosh for a skew-back support to the stock would be necessary, and that the proper place for this was in the tuyere-section, beginning just below the tuyeres and ending just above them, where there is nothing in the solid state but fuel, which is consuming, and no slipping or travel of stock takes place. The cubical capacity of a furnace of this design would necessarily be much less than in the old style, unless it was made very much higher. But I assumed that the loss of room for reduction could be overcome by making the size of the ore and stone charged much smaller, so that the gases would act more quickly. The next point was, what should be the size of the shaft, crucible, tuyere-circle, and tunnel-head for a given quantity of air? My first design was 12 feet diameter of shaft for 7000 feet of air, with a 9-foot crucible and 8-foot toyere-circle. This I soon reduced to 8-foot shaft diameter, which I concluded was large enongh for economical work, if regular travel of the stock on the walls could be maintained. I consulted with a number of experienced furnacemen and furnace-engineers, and the plan was well thought of by many of them; and, as I had also some offers of financial aid from them toward the risk of trying the experiment, my firm concluded

Jan 1, 1885

By George H. Ashley

The present critical state of the supply, distribution, and utilization of coal and the necessity for pooling and zoning coals calls renewed attention to the lack of any fully adequate classification of coal. In the past coals have been classified as anthracite, semianthracite, semibitumi-nous, bituminous, subbituminous coals, and lignite, and a few special types, such as splint coal and cannel coal. But under the term bituminous coal are included a great variety of coals differing markedly both physically and chemically. The term subbituminous coal covers as great a range of chemical differences. In order to distinguish these varieties of bituminous coals it has been customary to designate coal by names derived from the place where mined, or by the name of the bed from which it is mined. Thus, in the market reports, coals are quoted as Pocahontas coal, New River or Sewell coal, Moshannon coal, Ohio coal, Williamson County coal, Jellico coal, and so on indefinitely, no limit being set as to the boundaries of the area to which a given name is applied. Nor is there any scale by which the coal from one place may be compared with the coal from some other district or some other bed. On the one hand, coals from the same district may be quite distinct and sell at very different prices or coal from the same bed may differ greatly in different districts; on the other hand, coals from different states may be so similar physically and chemically that one could replace the other in practical use without any appreciable difference in service. The following classification, arrived at after a careful review of a large number of systems of classification and of all of the recognized characteristics of coal, brings together all coals that so nearly resemble each other physically, chemically, and in heating qualities that any coal of a given type could replace any other coal of the same type and grade in use. Thus, if coals A and B are classed as of the same type and grade they have, so far as known to the writer, approximately the same heating value when burned under the same conditions, and the same character, length of flame, and properties affecting transportation and stocking; and if of the same grade, approximately the same percentage of impurities.

Jan 1, 1920

A Discussion at a meeting of the New York Section, Dec. 2, 1914 D. H. BROWNE.-If 35 years ago we had met to discuss the subject that is before us to-night, the criticism that we must all be mad or we would not be here at all would have been perfectly applicable. No group of men would have come together a generation ago to discuss the subject of smelting ores without extraneous fuel, or largely by the oxidation of their own impurities, without incurring the imputation of being crazy. But metallurgy, like all other branches of human industry, progresses by idealism. In every generation there are old men who see visions and young men who dream dreams. Thirty-five years ago John Hollway conceived the idea that in the Rio Tinto ore the sulphur and iron, if properly oxidized, could be made to produce heat enough to carry on the smelting of the ores. He saw the vision. Twenty-five years ago Mr. Austin, of Montana, took out a patent on a furnace in which to carry out Hollway's ideas. He dreamed the dream. Twenty years ago a man working in Montana grasped the possibilities of this idea. To him has been given that inexpressible pleasure which comes from realizing the idea and making the concept concrete. Gentlemen, it gives me great pleasure to introduce to you the man who made the ideal real, Robert Sticht, of Tasmania. ROBERT C. STICHT, Queenstown, Tasmania.-I find it extremely difficult to act up, in the smallest degree, to the enconium passed upon me by Mr. Browne. It is true it has been my good fortune to be able to put some sort of method into the "madness" of 25 years ago; but I am not the originator of the idea, nor the only one who has carried it out. Mr. Browne mentioned the originator, who undoubtedly is Mr. Hollway. He also mentioned Mr. Austin, who gave the first instigation to pyrite smelting as now practiced. As against both of these men I was fortunate enough to be able to command the necessary natural resources to carry out the idea continuously in a practical way, so as to make it permanently possible.

Jan 4, 1915

By Philip D. Wilson

The mines of the Calumet & Arizona Mining Co. are situated in the Warren Mining District, Cochise County, Arizona, between Bisbee and Warren and adjoin those of the Copper Queen Consolidated Mining Co. and the Shattuck Arizona Copper Co. Paleozoic 1imestones.of considerable thickness have been intruded by granite porphyry. A great stock of the intrusive outcrops boldly near the city of Bisbee and is known as Sacramento Hill. From this central core the porphyry has tongued out into the limestone for many thousands of feet as dikes and sills of irregular shape and variable dimensions. Churn drilling has recently developed a large tonnage of secondarily enriched copper ore in the main porphyry mass of Sacramento Hill. While some ore has been found in porphyry in other parts of the district, it is relatively unimportant compared with that which occurs in the Paleozoic limestone as irregular lenses replacing favorable beds near porphyry contacts or associated with well-marked fracture zones often many hundreds of feet away from the intrusive. In a zone extending from Sacramento Hill for a distance of from 1,500 to 3,000 ft., the limestone has been extensively metamorphosed and in this contact metamorphic zone the ore occurs through a known vertical thickness of upward of 900 ft. and individual orebodies often show extension in a vertical direction of over 200 ft. At a greater distance from the intrusive stock, the ore occurs as lenses of greater horizontal than vertical dimensions with an average thickness of approximately 30 ft. An exception to this rule is found in the occasional steeply dipping mineralized fractures, almost true tabular veins, which are found long distances a way from the zone of contact metamorphism. The copper was probably introduced during or slightly later than the porphyry intrusion in the form of chalcopyrite and bornite. These primary copper minerals are always associated with pyrite and often occur as rich lenses in a huge mass or shell of pyrite carrying an insignificant percentage of copper. In many instances the copper-bearing solutions were preceded by siliceous solutions and these latter, often persisting during the period of mineralization, have thoroughly indurated the ore-

Jan 1, 1917

By T. M. Chance

THE first bituminous coal cleaning-plant to use the sand-flotation process1 was placed in operation on Oct. 1, 1925, at the tipple of the East Broad Top Railroad & Coal Co., at Mt. Union, Pa. The general principles governing the design of plants of this type and typical operating results of anthracite sand-flotation units have been previously outlined.2 I will, therefore, confine myself to a description of this particular plant and to some of the elements of design it incorporates. THE ORIGINAL MT. UNION TIPPLE The plant was installed to transfer coal from steel narrow-gage cars of 60,000 and 70,000 lbs. capacity to standard-gage equipment. The coal was hauled some 30 miles from the East Broad Top field. This coal, mined by the Rockhill Coal & Iron Co. and other operators, is a low-volatile slow-coking coal with- ash of high-fusion point. It is normally a high-grade coal that does not contain an excessive amount of free impurities, but it requires careful handling to secure a fair domestic yield, and, naturally, the need for narrow-gage transshipment increases the difficulty of the problem. The narrow-gage cars were discharged into an 8-car track hopper equipped with two feeders passing the coal to two 42-in. apron intake conveyors. Twin units were installed throughout in this original plant, two lump-and-egg shaking screens, two lump picking-tables, two egg picking-tables and two stoker conveyors. The stoker coal was loaded without cleaning. The loading tracks and booms were in duplicate and with the layout as originally installed either unit could be run independently, each unit shipping a different class of coal or both units making the same product.

Jan 2, 1926

By Milton R. Pickus, Earl R. Parker

THE modern theories of creep¹-4 in general have been based upon the concept of generation and migration of dislocations, with the generation process normally assumed to be rate controlling. The theories are generally deficient in that they fail to take into account many factors that are known to influence creep. The influence of the state of the surface of the test specimen has been almost completely overlooked; yet the present report shows that the nature of the surface may, in certain cases, govern the creep characteristics of a specimen. In the period since Taylor" applied the concept of dislocations to a study of metals, a school of thought has developed that closely relates the plastic deformation of metals to the generation and migration of dislocations through the crystal lattice. It might be expected that the thermal energy required for the generation of a dislocation would be different from that for migration of the dislocation through the lattice. Furthermore, the activation energy for generation would be expected to vary for different parts of the solid metal. It has been predicted that dislocations would be generated most easily at external surfaces, but could also be activated at certain internal surfaces such as grain or phase boundaries. Within the body of the metal a range of values for the activation energy might be expected because of different degrees of disorder at such regions as grain boundaries, impurities, and second-phase particles. The particular value of the activation energy that was rate determining could then depend on the specific conditions of a test. If, for example, the surface atoms were by some means constrained, the generation of dislocations in the body of the metal might become the important factor. On the other hand, other conditions may favor generation at the surface. It is possible then that the creep behavior may not be completely determined by the inherent properties of the metal. Even the environment in which a test is carried out could have a significant effect. In fact it is conceivable that in order to obtain the maximum creep resistance from a given alloy, the surface atoms must be so constrained that the activation energy for generating dislocations on the surface is at least equal to that required for generation in the body of the metal. On the basis of such considerations, and in view of the limited number of publications discussing this subject, it seemed that an investigation of the influence of the state of the surface on creep might yield information of both theoretical and engineering interest. Experiments on single crystals, demonstrating a variation in the mechanical properties due to alterations in the surface layer, have been reported by several investigators.6-13 he results of these experiments have been briefly summarized;14 consequently, the earlier work will not be reviewed here. As an example of these findings the observations of Cottrell and Gibbons may be cited. They reported the critical shear stress of a lightly oxidized cadmium single crystal is greater by a factor of 2½ than a specimen with a clean surface. Materials and Methods Single crystals M in. in diam and 8 in. long were prepared from Horse Head Special zinc, melted under an atmosphere of helium in a large pyrex test tube, and drawn up into a long ½ in. diam pyrex tube by means of a vacuum pump. The cast zinc rods thus produced were cut into convenient lengths and sealed in evacuated pyrex tubes. Single crystals were grown by gradual solidification of the remelted rods. Cleaving the ends of the single crystal specimens chilled by liquid nitrogen proved a simple method for determining orientations from the exposed basal plane from the markings left on the cleaved surface that gave the slip directions with sufficient accuracy for the experimental work. The specimens chosen for the experiments were those having the angle between the basal plane and the specimen axis within the range of 15" to 65". Since zinc single crystals are quite delicate, it was necessary to devise an appropriate method of gripping the specimens in order to suspend them in the furnace and apply the load. Stainless steel collars were prepared having an inside taper, the smaller end of the taper being of such a size that the specimen could just pass through freely. The tapered hole did not extend the full length of the collar; a sufficient thickness of metal remained so that a hook could be attached to provide a means of applying the load and suspending the specimen. One of the collars was slipped over the upper end of a specimen which was supported vertically in a steel jig. The collar was then heated electrically until the end of the crystal melted and filled the collar with molten zinc. At this point the application of heat was discontinued, whereupon the molten zinc quickly solidified, due to the chilling effect of the jig. The specimen was then inverted and the second collar applied in a similar manner. The jig served several purposes: limiting the length of specimen that was melted, providing excellent alignment of the collars with respect to the specimen axis, and protecting the specimen from mechanical damage. Once the specimen was suspended in the furnace and loaded, it was desired to accomplish the surface treatment with a minimum of disturbance of the specimen. Around the specimen was a long pyrex tube, the upper portion of which was approximately 1 in. in diam, and in it was a copper coil of such a diameter to fit snugly against the tube. A specimen, approximately ½ in. in diam and 4 in. long, was suspended by means of a stainless steel rod so that it hung within the copper coil. The lower portion of the glass tube was approximately ¼ in. in diarn, and passing through it was a 5/32 in. diam stainless steel rod which hung from the lower specimen collar. This portion of the glass tube and the stainless steel rod extended through the bottom of the furnace. A T-connector, with suitable packing, was attached to the lower end of the stainless rod to provide a water-

Jan 1, 1952

By Dale A. Vaughan, Oliver M. Stewart, Charles M. Schwartz

A. U. Seybolt (General Electric Research Laboratory)—The authors should be commended for adding some important information to our knowledge of the solubility of interstitial elements in metals. It is becoming increasingly evident that the effect of even traces of such elements have very far-reaching effects upon the mechanical properties of the body centered cubic metals. Those who have worked in this area know that the accurate determination of the small solid solubility limits in systems of the type reported by the authors is a quite difficult task, and it is therefore not surprising that frequently the results of different workers are not in agreement. It is instructive, and usually helpful, to plot the solubility results on log weight or atomic percent -1/T coordinates to find out if a straight line is obtained. A straight line is expected because in systems displaying solubilities of the order of 1 to 3 at. pet or less, Henry's law is usually obeyed—or at least well enough obeyed so that the deviation from linearity is not very appreciable. If Henry's law is obeyed, one canthen use the Van't Hoff Equation in the form In N = ?H/RT + C, where N is mole fraction, at. pet, or wt pet for small values, and AH is the partial molal heat of solution of the solute. R and T have the usual significance, and C is an integration constant. If one plots the reported nitrogen solubility values as indicated above, the three points fall reasonably well on a straight line. The oxygen values for the two upper temperatures fall very closely to the nitrogen values as shown in the authors' Fig. 15. However, the value at 500°C departs widely from the straight line established by the data at 1500" and 1000°C. It is, of course, true that one cannot place too much emphasis on the significance of a line established by only three points, but in the absence of reasons for anticipating deviations, data exhibiting wide departures from linearity should at least be examined closely. Fig. 16 shows the log at. pct -1/T plots for the authors Ta-O and Ta-Ndata including a solid circle point at 500°C and 1.8 at. pet for Ta-O, which is simply extrapolated from the two higher temperature points. In addition, the data of R. P. Elliott9 for Nb-O are shown. These points were picked off his curve and are not very exact, but as can be seen they line up well on a straight line. It is interesting, and probably significant, that the slope of Elliott's results is not far from those of Vaughn, et al. This is probably to be expected because one would anticipate that the partial molal heats of solution of oxyten in these two very similar metals should be not too far apart. AH for Ta-O is about -1900 cal per mol, while for Nb-O it is near -2300 cal per mol. Hence, this lends some support to the thesis that the point at 500°C for Ta-O is much too high. The data of Gebhardt and Preisedanz10 are also plotted, and it is seen that their data while lying on a linear plot, have an appreciably steeper slope. The possible reasons for this will not be discussed here except to point out that their pressure-composition data show anomalies which suggest that they may have been dealing with a different equilibrium from that being discussed. There is another consideration which would also suggest that the solubility at 500°C is lower than shown. The solubility values were obtained by the classic method of first establishing a lattice parameter-composition curve. This the authors did, and there is probably little doubt that it is quite accurate. Such a plot is generally almost error-free because it has a self-correcting feature in that any deviation from linearity makes a data point immediately suspect, and subject to confirmation. Unfortunately, this is not true with respect to the actual solubility values. These are obtained ordinarily by taking an alloy containing more solute than is soluble at some temperature and then thermally

Jan 1, 1962

By A. E. Outerbridge

I had the honor to present to the American Institute of Mining Engineers at the Pittsburg meeting, February, 1896, a paper having the foregoing title, in which I said : " It has generally been accepted as a fact that cast-iron, under the influence of repeated shocks, becomes brittle, and will finally break under a blow which otherwise it would have withstood. It will probably surprise metallurgists, therefore, to learn that experiment disproves the supposed fact, and establishes exactly its opposite. " The result of about a thousand tests of bars of cast-iron of all grades, from the softest foundry mixtures to the strongest car-wheel metal, enables me to assert with confidence that, within limits, cast-iron is materially strengthened by subjection to repeated shocks or blows." Three tables were appended showing increase of strength

Jan 1, 1905

By Jeff Steinhoff

INTRODUCTION The Henderson mine utilizes a highly mechanized, continuous, panel-caving, mining system to extract ore from a deep, massive, molybdenite deposit. The mine is located 80.5 km (50 miles) west of Denver, Colorado. The mine surface facilities are located 3,170 m (10,400 feet) above sea level in a steep valley on the eastern side of the Continental Divide. Milling facilities are 24 km (15 miles) west on the western side of the divide at an elevation of 2,804 m (9,200 feet) above sea level. The ore- body is located approximately 3,000 feet south of the valley under Red Mountain. Access to the ore for men and materials is through a 915 m (3,000-foot) deep, 8.5 m (28-foot) diameter, vertical, concrete-lined, service shaft. Access from the mill is through a 15.5 km (9.6-mile) rail haulage tunnel. The mine is ventilated through an additional intake shaft and two exhaust shafts. Mine production at this time is 27,255 mtpd (30,000 stpd). The mine ventilation system supplies 1,038 cubic meters per second (2.2 million cfm) through approximately 60 miles of drifting or 2.7 tons of air per ton of ore mined. There are 130 fans in the mine in fixed locations and in vent lines with 6,900 connected horsepower in the mine. MINING METHOD AND LAYOUT The orebody is divided vertically into two major zones. The upper zone is the 8100-level production area. The bottom zone is the 7700- level production area which is in the early development stage. The rail haulage level at 7500 feet is common to both production zones. Each mine production zone consists of five associated sublevels. The cave undercut level is 16.8 m (55 feet) above the production level. Two boundary cutoff levels are located 44.2 m (145 feet) and 62.5 m (205 feet) respectively above the production level. The fresh-air level is positioned 15.2 m (50 feet) below the production level, and the exhaust vent level is 19.8 m (65 feet) below the production level. Horizontally, each production zone is divided into three panels each, 224 m (800 feet) wide. These panels are caved from south to north. As the caving in one panel nears completion, caving in the adjacent panel is initiated. Development for the caving panels is continuous so that the sublevels above the production level and the production level itself have a combination of development drifting and production-related activities. UNDERGROUND VENTILATION NETWORK The ventilation system is zoned in the same manner as the orebody itself. One major split of 600 cubic meters per second (1,270,000 cfm) ventilates the 8100-level production zone; one split of 100 cubic meters per second (210,000 cfm) ventilates the development of the 7700- level production zone; and one split of 165 cubic meters per second (350,000 cfm) ventilates the 7500 rail haulage level. The haulage tunnel requires an additional 188 cubic meters per second (400,000 cfm) of air. Development-drift ventilation is accomplished by hanging 1.0 m (3.5-foot) diameter steel ducting in the drifts with 40-horsepower, 0.96 m (38-inch) diameter fans supplying 9.4 cubic meters per second (20.000 cfm). The normal maximum length for these systems is 300 m (1,000 feet). The 8100-level production-area ventilation system is especially suited to a high level of mucking activity confined in a small area. Approximately 93 per cent of the mine's total production is transferred from the drawpoints to ore passes in 10 production drifts. The active area in each drift is 300 m (1,000 feet). Twelve 5-cubic-yard LHD units with Cat turbo- charged 170-horsepower engines are assigned to the area. Under these conditions, more than one LHD is assigned to a particular production drift. Adequate ventilation is maintained by making an air change every 97 m (320 feet) along the production drifts. Fresh air is brought into the production drifts from the fresh-air level through 1.37 m (4.5-foot) diameter raises. Air travels south along the production drift to the ore pass where it is exhausted down the ore pass to the exhaust level. The ore pass is followed by another intake which is followed by an ore-pass exhaust. At the south end of the production area, a series of exhaust fans maintain a southerly air- flow through the production level.

Jan 1, 1981

By R. R. Brandenthaler

CONTROLLING -the pressure under which a well produces crude oil has advantages that are ap¬parently not entirely realized by many operators in the Mid-Continent district. The possibilities of utilizing well pressures are indicated by a series of ex-periments recently completed by the Bureau of Mines in which pressure control was successfully applied to 20 wells in, the Davenport field. The flowing period of all of .the wells was lengthened in some instances it was. more than doubled. The daily oil production from approximately one-half of the tested wells was in-creased. The amount of gas produced per barrel of oil was decreased, and this, in addition to a slower rate of decline in production, indicated that the ultimate re-covery had been increased. The successful application of pressure control to flow-ing oil wells must take into consideration the relation-ships existing between pressures in the different parts of the system which, though not equal, are nevertheless more or less interrelated. These relationships, which have such an important bearing on the results obtained by applying pressure control, are as follows: A change in rock pressure will affect the tubing pressure, casing pressure, and differential pressure, but it will not affect the trap pressure. A change in tubing pressure will affect the differential pressure and casing pressure; also, a change in casing pressure will affect the tubing pressure and differential pressure. Trap pressures are not affected by rock pressure, casing pressure, tubing pressure, or differential pressure, unless the traps are required to handle gas and oil beyond their capacity. Trap pressures will affect the differential pressure, tubing pressure, and casing pressure and any changes at the well-head, whether differential pressure, tubing pres-sure or casing pressure, will affect the pressures in the well. Any change in rock pressure results in a change in the tubing pressure, casing pressure, and differential pressure. When any sudden or unusual change in well-head pres-sures occurs (for example, an erratic tubing pressure), and when a sudden decrease in oil or gas takes place, it is al-ways advisable to note whether the trap pressure has changed. If the trap pressure has not changed, note whether the oil line from the trap to the flow-tank has become clogged, as would be evidenced by a rise in the oil level in, the trap. If the oil line is functioning properly, and if the trap pressure has not changed, the flow-line from the well to the trap should be inspected. If it is free from obstructions, then changes in the differential pressure, tubing pressure, and casing pressure must be due to changed well conditions.

Jan 4, 1927

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By J. W. Craig, H. L. Walker

Industry has for many years recognized the dependence of certain mechanical and physical properties. as well as workability, upon grain size variations in brass. Although the dependence of properties upon grain size has been recognized there are not many instances where a planned program of testing has been conducted and where the only intentional variable has been grain size. In particular the literature is limited with respect to the effect of grain size on the endurance limit, though there are many industrial applications where the brasses are subjected to cycles of repetitive stresses. Literature A number of the physical and mechanical properties of a given brass sheet, in the annealed condition, will depend upon: (I) The ready-to-finish grain size before final rolling, (2) the percentage deformation by cold working, and (3) the time and temperature of annealing. The first and second variables affect the recrystallized grain size, and the third variable affects the coalesced grain size. Gibbsl has shown the effect of two different ready-to-finish grain sizes upon the tensile strength and hardness of deep drawing brass strip after a definite amount of cold rolling. The smaller the ready-to-finish grain size, the higher the tensile strength and hardness, but with lowered ductility, Gibbs also demonstrated, for a given time and temperature of anneal, that the tensile strength, hardness, and elastic limit are higher for the smaller ready-to-finish grain size, but the elongation is lowered. Townsend and Greena112 have reported data which show that cold working increases the tensile strength, hardness, and load carrying ability of deep drawing brass sheet under reversed stress. Greenall and Gohn3 have reported data which show that the smaller grain sizes have higher tensile strength and hardness properties, and the data also show that increased cold working increases the tensile strength and hardness properties of deep drawing brass sheet. Kommers4 has reported data for tests of brass of known ready-to-finish grain size, a specific amount of cold reduction, and annealed at different temperatures above and below the recrystallization temperature. Kommers' results indicate that annealing below the recrystallization temperature does not change the tensile strength and hardness properties, but the endurance limit may be increased from 22,000 to 28,000 psi. The increased endurance limit is explained as resulting from the reduction of internal stresses by a stress-relief anneal. Burghoff5 and associates have reported data on creep tests, over

Jan 1, 1949

By Carl F. Floe, Michael B. Bever

THE possibility that carbon may be soluble in copper to a limited extent has been recognized for over a century. The quantitative investigation of this problem, however, requires more sensitive techniques than have formerly been available. Three recent developments have made possible more accurate determinations: the vacuum-fusion method of analysis, the production of copper of high purity and the availability of high-purity refractories, particularly graphite. In addition to its obvious theoretical interest, the problem of carbon solubility in copper is of practical importance. In the production of copper and of high-copper alloys, carbonaceous covers are frequently used. If even minute amounts of carbon are dissolved, insoluble carbon oxide gases will be formed when such metals are poured under oxidizing conditions. A mechanism of this kind could well be one of the principal causes of gas porosity in casting copper-base products. REVIEW OF LITERATURE In 1823 Vivian1 raised the question as to whether copper by overpoling becomes "combined with a minute portion of carbon." Karsten2 asserted, in 1832, that carbon reduces the high-temperature strength of pure copper, so that when the carbon content has reached 0.2 per cent the metal will be brittle at a dark red heat. According to Karsten, carbon contents of o.05 per cent make it difficult to hot-work copper. He also reported that the specific gravity of copper is 8.8969 and that it increases to 8.92 58 if the copper is cemented with carbon and then melted. He emphasized the difficulty of determining analytically the small amounts of carbon present in copper. The metal was removed by wet methods and the residue considered as carbon. At Percy's request, Dick,3 in 1856, carried out various working tests on copper that had been in prolonged contact with carbon, and found that the working properties of the metal had not been affected. He also attempted to determine the presence of carbon analytically. In one experiment the copper was dissolved and the residue was fused with litharge, and in another essentially a combustion analysis was made on a copper sample. In a final experiment, a sample was dissolved and the residue subsequently subjected to a combustion analysis. Indications of as much as o.005 per cent carbon were found, but Dick considered his work inconclusive largely because of the possible interference of sulphur. Percy4 concluded, from Dick's experiments and from some experimental work of his own, that the solubility of carbon in copper had not been established with

Jan 1, 1945

By Arthur L. Christenson, Clarence E. Jackson

In the establishment of the relationship between weldability and hardenability, two methods have been employed in correcting for the grain growth produced in the heat-affected zone: first, the hardenability calculated from chemical composition* may be corrected to the grain size observed in an actual weld? or, second, a hardenability test may be made on the steel quenched from a temperature high enough to produce a grain size comparable to that found in the heat-affected zone.8 In order to obtain grain sizes in the end-quench hardenability bar comparable to those resulting in the base metal from the welding cycle, a quenching temperature of 2Ioo°F. has been used. In studies of the end-quench hardenability specimen quenched from 2Ioo°F. instead of from a lower temperature of I7OO°F., it is impor-TaiiT to ascertain The relative cooling rates for various distances along the bar. It is a question as to whether the cooling occurs at the same rate or whether there is any significant difference from the standard cooling-rate curve published by Jominy and confirmed by others.4,5 This paper reports experimental evidence concerning the effect of quenching temperature on the cooling rates in the end-quench hardenability test. The effect of quenching temperatures on cooling rates has been studied by a number of investigators.6'7 French has considered this effect from both theoretical and experimental aspects. In French's studies on complete quenching of spheres and rounds, an increase in the quenching temperature caused an increase in the cooling rate at 720°C. at the center of the specimen. The center cooling velocity also has been shown to be dependent upon the surface per unit volume for the type of specimens studied; the velocity of cooling increases with an increase in the surface per unit volume. Three methods of indicating the rapidity of cooling of a body of metal during a quenching operation have been propped: I. The time it takes for the metal to cool from the quenching temperature to a temperature halfway between the quenching temperature and the temperature of the quenching medium (half-temperature time): Grossmann, Asimow and Urban7 justify the use of this criterion by the fact that the half-temperature time includes the temperature and time of incubation as well as the zone of formation of pearlite and, further, the data so derived accord very closely with experimental values. 2. The time interval the metal remains in a given temperature range; for example,

Jan 1, 1944

By L. D. Fetterolf, G. T. Mahler, W. M. Peirce, R. K. Waring

UNTIL recently, the only commercial method of producing magnesium has been fused salt electrolysis, despite a considerable amount of experimental work on the direct reduction of magnesium oxide. In this early work, a number of investigators demonstrated that magnesium oxide would react with any one of several reducing agents to produce magnesium vapor, but that the mixture of magnesium oxide and reducing agent must be heated to a high temperature even in a vacuum. In particular, it was demonstrated that silicon and aluminum are effective reducing agents and that when either of these is used the magnesium vapor can be condensed to massive metal. In spite of this knowledge, no successful commercial reduction process was developed, at least in this country, because of the operational difficulties imposed by the requirement of high temperature and vacuum and because of the high cost of the reducing agent. The outstanding experimental work done by Pidgeon, who carefully reviewed all of the known methods of making magnesium and then selected ferrosilicon reduction, overcame some of the operational difficulties. The process developed by Pidgeon comprises briquetting a mixture of calcined dolomite and reducing agent, pre-heating the briquets to about 600°C. in an externally heated alloy retort, reducing the MgO with silicon in an evacuated horizontal alloy retort heated externally to about 1150°C., and condensing the magnesium vapor to a solid in a cold extension of the retort projecting beyond the fr6nt of the furnace. A major advantage of Pidgeon's process is that the retort is not cooled down between charges. Earlier investigators had used apparatus that necessitated cooling and reheating of the retort between charges. Early in January 1942, when the War Production Board was considering the Pidgeon process for quickly increasing the production of magnesium, The New Jersey Zinc Co. offered to have a research investigation of the process carried on, with the hope of assisting in its further development. This offer was accepted, and a two-retort pilot plant was built at Palmerton and put in operation on Jan. 29, 1942. An intensive investigation of certain phases of the process was carried out in the ensuing four months. This investigation was completed in the last part of May 1942, and the pilot plant was then shut down. Subsequently, The New Jersey Zinc Co. was requested to have further development work done on the process, and a more extensive investigation was undertaken in August I942 under contract with the War production Board and under the super- vision of the War Metallurgy Committee. This paper describes the phases of the investigation that are thought to .be

Jan 1, 1944

By George K. Foster, Charles D. Borror

THE Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest openpit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. THE ORE BODY The ore body is a serpentinized peridotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur perpendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber [ ]

Jan 1, 1946

By Heinrich Freyn

THE American iron and steel manufacturer finds himself to-clay barely at the threshold of enormous possibilities for practicing rational economy in the use of fuels. The fuel cost is by no means the smallest of items which enter into the cost of manufacture of iron and steel products, but the great wealth of this country in high-grade fuels, together with a protective tariff, has heretofore made fuel economy relatively unimportant. In Germany, the use of raw coal for the purposes of iron and steel manufacture has been all but abandoned and large sums of money, formerly irrevocably wasted, are now being saved. When scanning the literature of this country devoted to the application of gas power, but little information will be found on a subject which, however, is destined to become of considerable importance in the United States, namely, the use of coke-oven gas for the generation of power in gas engines. This lack of information can be traced to the fact that the regenerative by-product coke oven with its large amount of surplus gas is still far from having attained in this country the universal application which it has found in Europe. This statement needs hardy any corroboration other than the evidence of statistical investigations made by E. W. Parker of the United States Geological Survey, according to which only approximately 25 per cent. of the total coke produced in this country in 1912 was made in by-product coke ovens, whereas 75 per cent. was produced in bee-hive ovens. This entailed the enormous loss of over $80,000,000 in non-recovered by-products, such as gas, tar, and ammonia, without considering the substantial loss due to the non-recovery of benzol from the coal. There are two more or less distinct fields of application of the by-product coke oven: one, to furnish as the main product metallurgical coke of specified quality, and surplus coke-oven gas as the by-product, and the other, to carbonize high-volatile coals, and thus produce as the main product large quantities of gas, high in heat value and rich in illuminants, adapted primarily for domestic heating and lighting, while domestic coke becomes the by-product.

Jan 4, 1914

By C. D. Woodward

PRIOR to 1902, the tramming of ore from the stopes to the shafts, in the Butte mines, was done by man or animal power, but the demand for greater tonnage and the need for more improved methods of tramming the ore resulted in the installation of the compressed-air locomotive in a few mines. Some of the objections to animal haulage were thus eliminated, but this locomotive was not generally adopted, because of a number of limiting features. It was superseded by the electric trolley locomotive. The early types of trolley locomotives were not satisfactory from the operators' viewpoint, but. they had many economic advantages and after a number of years, in which improvements were constantly made in the structural details, they became dependable, so that the use of animals for main haulage in the mines has now been practically abandoned. There are now operating in the Butte mines of the Anaconda Copper Mining Co., 185 trolley-type locomotives, each of which has replaced five animals. It cost approximately $50 per month to keep an animal, hence the economies that resulted fully justified the expenditure of electrifying the haulage systems. The haulage conditions in this company's mines possess many advantageous features that are not always found in underground mine workings. The drifts and crosscuts are large, approximately 5 ft. (1.5 m.) wide by 7 ½ ft. (2.3 m.) high, and have curves of no less than 18 ft. (5.5 m.) radius; and the roadbeds of the drifts and crosscuts have a uniform grade of 0.5 per cent. toward the shaft, or in favor of the loaded trips. In all of the mines, except two, the track gage is 18 in. (45.7 cm.), and all tracks in the main haulageways are laid with 25-lb. (11.3 kg.) rails. The stations at the shaft are large, well-lighted, clean, and cool. The average temperature of ,the stations, however, is about 75° F. (24° C.), while the average temperature in some of the drifts and crosscuts is 92° F. (33.5° C.).

Jan 2, 1922

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939

By George A. Moore, Donald P. Smith

In spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which complicate the effects; and (3) the fact that the body-centered cubic modification does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions. Review Although only a comparatively few investigations have so far been made on the pure system iron-hydrogen, there is a much larger volume of literature which throws some light on the problem but falls short of a place in the systematic investigations, either because no attempt was made to measure equilibrium conditions or because the metal used was not iron or the gas not pure hydrogen. Such results have been variously dismissed in the past as of no importance, or as too complicated to try to explain; or they have been explained in terms of any of a dozen or more pictures, each of which is contradicted by data from other sources. The present importance of these data thus arises from their very mass and diversity, which present a picture of occlusion as a phenomenon whose variability cannot be ignored. We have attempted to organize the literature into groups comprising similar experiments or data leading to similar conclusions, thus of necessity sacrificing accuracy of historical order. Lattice Occlusion.—Throughout this discussion, the term "lattice occlusion" will be used to denote the formation of a simple solid solution of a gas in a metal lattice, usually of interstitial distribution. The word

Jan 1, 1939