Search Documents

By William E. Ford, Edward Salisbury Dana

The Silicates are m part strictly anhydrous, in part hydrous, as the zeolites and the amorphous clays, etc. Furthermore, a large number of the silicates yield more or less water upon ignition, and in many cases it is known that they are, therefore, to be regarded as basic (or acid) silicates. The line, however, between the strictly anhydrous and hydrous silicates cannot be sharply drawn, since with many species which yield water upon ignition the part played by the elements forming the water is as yet uncertain. Furthermore, in the cases of several groups, the strict arrangement must be deviated from, since the relation of the species is best exhibited by introducing the related hydrous species immediately after the others. This chapter closes with a section including the Titanates, Silico-titanates, Titano-niobates, etc., which connect the Silicates with the Niobates and Tantalates. Some Titanates have already been included among the Oxides.

Jan 1, 1922

E. E. Russell Tratman, New York City (communication to the Secretary): Mr. Glenn's paper brings up again the question of the part played by coal-dust in colliery-explosions. In the discussion of Sir Frederick Abel's paper on " Accidents in Mines," read before the Institution of Civil Engineers,? much was said about the dangerous properties of coal-dust, and several instances were given of the successful use of a spray of water, water and compressed air, or exhaust-steam from an engine, to keep the mine SUEciently damp to prevent the formation of dust clouds. Methods of preventing shots from blowing out; of using water cartridges to prevent flame ; and of using lime cartridges, wedges and other means of breaking down the coal were also discussed. Mr. Emerson Bainbridge referred to the explosive termed " roburite " (ammonium nitrate and

Jan 1, 1895

[Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'38) Min. Engr., Dir. Bureau of Mines, Manila, P. 1. Abbott, Agatin, (J'40) Asst. Geol., Trench Mine, Patagonia, Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Tennessee Coal Iron & R.R. Co., 1642 Brown Marx Bldg., Birmingham, Ala. Abel, Raymond L., (M'28) Prof., Chem. Engrg., Univ. of Pittsburgh, Pittsburgh, Pa. Abel. Walter D., (M'32) Min. Engr., Div. of Corporations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 4800 Patterson Ave.. Richmond, Va. Abell, Leo M., (M'31) Research Met., Mount Morgan Ltd., Mount Morgan, Queens., Australia. Abenius, Hakan V., (M'37) c/o Falu Gruva, Falun, Sweden.]

Jan 1, 1940

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By John A. Gann

The following investigation constitutes a brief réumé of the more important binary magnesium alloys from the standpoint of metallo-graphic technique, and the effect of heat treatment on structure and properties. The comparative newness of the subject justifies this procedure as a preface to a more detailed study of each individual series of alloys. The work was started with the idea of practical application in the industry rather than as a theoretical investigation. The alloy compositions studied were selected as those most likely to show whether heat treatment would produce beneficial results. Furthermore, it was considered satisfactory to use commercial 99.9 per cent. magnesium, the best commercial grade of alloying ingredients, and to limit the time of heat treatment at the expense of incomplete equilibrium. These facts must be kept in mind when examining the results obtained, and the conclusions drawn. Preparation of Alloys All melts were made in an oil-fired cast-steel pot, approximately 12 in. dia, by 12 in. deep. Approximately 15 lb. of flux and 50 lb. of magnesium were melted and the calculated amount of alloying metal was added. After thorough alloying and puddling, the metal was chill cast in a graphite mold with four 1/2 by 1/2 by 4 in. bars fed from a common sprue and runner. The next higher composition alloy in a given series was made by adding the calculated amount of metal to the heel from the preceding cast. The pot was thoroughly cleaned after each series and new flux then introduced, thus avoiding possible contamination from earlier melts. The percentage compositions given in Table 1 are the calculated values. While not all alloys were analyzed, enough were checked to indicate that the reported compositions are correct to a few tenths of one per cent. A more detailed description of the foundry methods employed has been given in a previous paper. 1

Jan 1, 1929

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By Michael Tenenbaum

The importance of semikilled steel as a high tonnage grade has long been recognized. The increasing severity of the applications for which semikilled steel is used makes it desirable to obtain further information regarding the features of open hearth practice and ingot structure that can affect steel performance in subsequent rolling and fabricating operations. Accordingly, an investigation is being carried out studying the structure of various types of semikilled steel ingots. This paper reviews some of the observations made and information gathered in this investigation. By definition, semikilled steel may be considered to include all nonrimming steels in which the natural shrinkage occurring during ingot solidification is offset to an appreciable degree by gas formation. Accordingly, this type of steel includes the entire range intermediate between rimmed and fully killed steel. The resultant ingot structures range from those of steels that have been capped to suppress a weak rimming action to those steels that have been killed in the furnace or ladle to the extent that no mold deoxidizer is required. A survey reported to the 1946 -AIME Open Hearth Conference' reviewed the practices being used at 28 major plants for the deoxidation of semikilled steel. It was found that most plants divide the deoxidizing additions between the ladle and the mold—many of the plants adding only minor amounts of deoxidizer to the bath or none at all. Silicon, aluminum and titanium were the only elements used for ladle and mold deoxidation. Mold deoxidizers were added as capping additions or as uniformly fed additions. Several practices were reported in which the steel was deoxidized in the ladle to the extent that little or no mold deoxidation was needed. No reference was made to grades capped by using special mold designs or special closures over the top of molds. .Accordingly, specific examples of this type of practice will not be considered in this paper. It appeared from this survey of deoxidation practice that semikilled steel can be divided into three types, namely, capped semikilled, in which aluminum is added near the end of pour or after shut-off, intermediate semikilled steels, in which aluminum is fed uniformly throughout the pour, and semikilled steels requiring no mold deoxidation. In an attempt to cover the ingot structures obtained by the range of practices reported in the preceding survey, three series of experimental heats were made using increasing amounts of aluminum, silicon and titanium for ladle deoxidizers. The ladle deoxidizers were added as stick aluminum, 50 pct ferrosilicon and 20 pct ferrotitanium (4 pct carbon), respectively. Two methods of studying ingot structures were used. Ingots were removed from production, burned longitudinally and machined to allow observation of the central pipe and coarse blowholes. During the machining operation much of the finely porous subsurface structure was obliterated. Accordingly, observations were also made

Jan 1, 1949

By GEORGE D. RAMSAY

WHEN the Ironton blast furnace of the Columbia Steel , Co. was first put into operation the iron ore was mined frol11 the deposit near Iron Springs, Utah. This is principally a hematite with 12 to 20 per cent of magnetite finely disseminated throughout the ore. It varies from a fairly soft broken rock structure to that which is hard and compact. In the broken form it will weigh about 150 lb. per cu. ft., and in place the density is approximately 250 lb. per cu. ft. The first ore received for the blast furnace was crushed so as to pass through approximately a 4-in. square opening screen. A typical screen test of this ore is shown in Table 1.

Jan 1, 1935

By Myers, J. F.

The purpose of the mill tests reported herein, was to determine the relative power efficiency of fast and slow rod mill speeds on the ores of the Tennessee Copper Co. The tests were carried out at the lsabella Mill of the Tennessee Copper Co. under normal operating conditions. Every effort was made to keep the ore supply and other conditions constant, but it will be noted that some slight variation did occur. The open circuit 6 by 9 rod mill, and ore, used in these tests have been previously described.' Four motor drive pinions were available and the tests were performed in the following manner: each pinion was used to drive the mill for a period of one week. Constant sampling prevailed during the test run, and a composite sample for each speed test was made. Realizing that some slight liner wear took place during the four-week test-run, and that some slight variation of the ore may have taken place, a second and then a third series of four-week test- runs were made with the four different pinions. The screen analysis of each of the thee-week run samples at the various speeds were composited and the results are shown in Table 1. The authors feel that the 12 weeks of operation consumed during these test-runs would represent fairly the effect of each mill speed. The data of line 37 show that within the error of sampling and plant operation, the tons of minus 65-mesh material generated per horsepower hour was the same at all four speeds.

Jan 1, 1949

By Joseph B. Umpleby

PROGRESS in the petroleum industry in 1929 has been characterized by outstanding accomplishments in the fields of new discovery of supply, economic control of production, increased efficiency and reduced costs of recovery, and lowered costs and greater flexibility in manufacture. Resources have been developed in an outstanding degree in the Kettleman Hills. California, the Oklahoma City field (which adds a large potential area in central Oklahoma), the discovery of Woodbine sand production in East Texas, and the discovery of Wilcox sand production in west-central Kansas. Engineering technique has progressed both along the lines of development and production, with a net result that costs have been reduced and extraction increased in notable degree, although it is impossible to give a close measure of either. In the field of re- fining crude oils variations to the end of promoting reduced cost and greater flexibility has been more important than genera! acceptance of innovations in practice.

Jan 1, 1930

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

By Marcus A. Grossmann

The Institute has established this lectureship to honor the memory of a great American metallurgist, one whose fame has continued long after his passing. As one scientist recently stated it, "All metallurgical texts gradually become outdated and outmoded, except those of the great Henry Marion Howe." It seems fitting, then, that, once every year, we shouId review, in his honor, some aspects of the science in which he was such a distinguished leader, and also discuss any new data that may help to clarify our concepts. It is my privilege, for which indeed I express the deepest appreciation to this Institute, to offer for consideration a few thoughts on the toughness and fracture of hardened steels. Before proceeding to the data, I wish to express my great indebtedness to many associates whose stimulating discussions, generous contributions of data and cooperation in experiments are gratefully acknowledged. (But I wish to absolve them of any blame that may arise from the way in which their discussions and data have been used!) First, Dr. Edgar C. Bain, Vice President, Carnegie-Illinois Steel Corporation, whose amiable but merciless criticisms and always constructive and thoughtful suggestions help unfailingly to guard against pitfalls. Then to associates at Gary Steel Works, especially Mr. H. B. Wishart, Mr. W. K. Smith and Mr. V. Elliott, for great assistance in securing data. Also to Col. C. H. Greenall, Director of Laboratories, Frankford Arsenal, and his metallurgical staff, including Messrs. J. K. Desmond, H. Markus, D. F. Armiento, H. Rosenthal and Henry George, for numerous data and illustrations. Further to Dr. J. R. Low and Dr. M. Asimow, for helpful discussions of effects of states of stress during deformation and rupture, to Mr. J. M. Hodge for discussions and data, to the staff of the U. S. Steel Corporation Research Laboratory for advice and data, and to the Metallurgical Staff at Duquesne Steel Works. The individual acknowledgments will also be found under illustrations. Acknowledgment is also due to Mr. S. C. Snyder for incredibly meticulous scrutiny of manuscript. To all of these, grateful thanks. Introduction The discussion to be offered here will deal with quench-hardened steels only, and may perhaps be considered under three headings: 1. It was found that, when ferrite was precipitated in the (prior austenite) grain boundaries of hardened steel, the notch-bar toughness was much less than in pieces fully hardened. The fracture took place in the ferrite, and the loss in toughness is attributed to the lower cohesive (cleavage) strength of the ferrite, as cornpared with martensite. 2. When notch-bar impact test pieces of quenched and tempered steels were examined as to their mode of fracture, it

Jan 1, 1947

Adams, John H., Pres. & Mgr., Alabama Lime & Stone Corpn., 1302-4-8 First Ave., Birmingham, Ala. '14 Adams, L. W., Otis Steel Co., Riverside Plant Cleveland, Ohio. '15 Adams, Leland D., Min. Engr., Mgr., Signal Mines Co., Goldbanks Quicksilver Co., 485 California St., San Francisco, Cal. '14 Adams, R. L., Min. Engr., Old Ben Coal Corpn., Mine 12 Christopher, III. `19 Adams, Robert M., Robert M. Adams Co 1201 Fidelity Bldg., Duluth, Minn. '20

Jan 1, 1925

By John Wellington Finch

WHAT is an engineering opportunity? To the mining .engineer the natural assumption is that the first requisite 'is a mineral deposit, but, of course, it is not so simple as that. There are at various points on the earth really very great mineral deposits which, on account of geographic location, backwardness of the country, or hostility of its natives, are now, and for a long time to come will be, quite valueless. The mining engineer, and for that matter the civil engineer, is more dependent upon the decisions of capital than upon any other factor in his profession. Ordinarily it is to be assumed that money will go to any place where it is clear that an adequate return upon its investment can be secured, but for many years it has not been safe to depend upon this. ' As already stated, there are many places where local conditions are such that mining is not safe to engage in and there are still other places in which conditions have been so aggravated by the Great War and by the social unrest which has upset the Asiatic region that capital is naturally most reluctant to venture, even when engineering data makes the undertaking appear attractive. It will be evident, I. believe, that there are many factors vital to the success of a mining enterprise in some of the remote countries which we do not have to consider in the United States and which do not, in fact, exist here.

Jan 1, 1924

By John Wellington Finch

THE- impression which the public has of northern Canada is that it is a' vast wilderness of forests; river's, and. lakes, sparsely inhabited by. a few Indians and `containing a few, scattered trading posts of the Hudson Bay Co. This is far from the facts. The building of the Canadian Pacific Railway led to the discovery, in 1883, of the nickel deposits of Sudbury, Ont.; these are the largest known nickel deposits in the world and produce about 90 per cent. of the world's output of nickel. The building of the Temiskaming and Northern Ontario Railway north, from North Bay, to open up farming lands along Lake. Temiskaming, resulted in the discovery and development of the great silver deposits of the Cobalt area, Ontario. Since the discovery of these deposits in 1903 to Dec. 31, .1923, Cobalt has produced a total of ' 327,301,897 oz. of silver, valued at $212,668,434, and paid in. dividends $88,338,185. In 1923 the production of Cobalt amounted to 10,285,247 oz. of silver. Just south of Cobalt, in South Lorrain,. a. new silver district has recently been developed and mills have started production. These deposits are of such extent that 'a branch railroad is under construction from Cobalt to that area. Northwest of Cobalt is the Gowganda silver area which is also a producer of silver ore and is now attracting outside attention. This area is not connected by railroad.

Jan 1, 1924

By William E. Ford, Edward Salisbury Dana

1. Normal Class (25) Barite Type 2. Hemimorphic Class (26) Calamine Type 3. Sphenoidal Class (27) Epsomite Type Mathematical Relations of the Orthorhombic System Crystallographic Axes. - The orthmhombic system includes all the forms which are referred to three axes at right angles to each other, all of different lengths. 296 Any one of the three axes may be taken as the vertical axis, c. Of the two horizontal axes the longer is always taken as the b or macro-axis * and when orientated is parallel to the observer. The a or brachy-axis is the shorter of the two horizontal axes and is perpendicular to the observer. The length of the b axis is taken as unity and the lengths of the other axes are expressed in terms of it. The axial ratio for barite, for instance, is a : b : c = 0'815 : 10 : 131. Fig. 296 shows the crystallographic axes for barite.

Jan 1, 1922

By K. A. ACKLEY

The petroleum industry experienced a year of satisfactory accomplishment in Oklahoma during 1945. Crude oil production was increased, a new record for recent years was established in well completions, and refinery operations were maintained at a maximum level. Daily average crude oil production increased to 382,000 bbl., reflecting a 13.5 per cent gain compared with production during the previous pear. Total wells drilled during 1945 amounted to 2556, a gain of 28.7 per cent over 1944 Refinery throughout averaged 187,500 bbl. daily, an increase of approximately 4 percent over the preceding year.

Jan 1, 1946

Aamot, Olav Crone, Chem. Engr., Norsk Elektrokemisk, Kongensgt. 18, Olso. Norway. '29 Abadilla.-Quirico A., Dir., Bureau of Mines Manila, P. I. '38 Abbott, Clarence E., V.P., Charge of Raw Materials, Tennessee Coal, Iron & R.R. Co., 1212 Brown-Marx Bldg., Birmingham, Ala. '04 Abel, Raymond L., Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '29 Abel. Walter D., Cons. Engr 1839 Holmby Ave., W. Los Angeles. Calif. '32 Abele, Louis T R. F. D. 5. Susquehanna Trail, N., York. Pa. '31 Abell, Leo M., Ore Dressing Investigator, School of Mines Adelaide, S. Australia. '31 Abenius. Hakan V., Mine Supt., Bolidens Gruvaktiebolag Boliden, Sweden. '37 Aborn, Robert H., Asst Met., Research Lab., U. S. Steel Corp. Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service-Club, 16 St. James' Sq., London, S. W. 1, England. '28 Abrams. Charles Jackson 1624 17th St., Denver, Colo. '36 Abstein, Henry T., Engr. & Mgr., Profile-Tamarack Mines Co Yellow Pine, Idaho. '27

Jan 1, 1938

By A. B. Kinzel

ALTHOUGH the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approxi-mately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cementite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consider-ation of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:1 C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown in Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850° C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the

Jan 1, 1934

Jan 1, 1970