Search Documents

By H. C. Rogers

It has been shown previously'- 3 that when a mild steel or iron is charged with hydrogen, the normally observed yield point is eliminated or considerably

Jan 1, 1960

By C. D. King

THE key to maximum production of ingots for the war effort is maximum production of pig iron. For any given furnace and ore, the most important single influence on blast-furnace production is the quality of the furnace coke. It is generally recognized that undoubtedly deterioration of Pittsburgh coking coals will be accelerated by the depletion of some of the better grades' of coal; the extension of mine mechanization, with attendant degradation of coal quality; and the opening of new coal fields, some of which are known to be fairly high in sulphur. All of these factors, contributing as they do to higher ash and sulphur, and not infrequently to inferior quality of coke, made it desirable that an extensive study be undertaken to determine the effect of washing some coals that closely approximate the average chemical composition of coking coals to be expected in the future by the subsidiaries of the United States Steel Corporation in the Pittsburgh district. It was deemed advisable to study the improvement obtained by washing such coals and to determine the need for supplementing the existing coal washery at Clairton to assure continued maximum production of pig iron from presently available furnace stacks. The existence of the coal washer at Clairton made it possible to conduct tests on coals used in raw form and on similar coals after washing. This study covers an investigation of the quality of furnace coke as affected by washing coking coals, and is confined to the use of 100 per cent high-volatile Pittsburgh seam coals from Fayette and Greene Counties in the manufacture of furnace coke. It covers the improvement in chemical and physical properties as well as the degree of uniformity in coke obtained by washing these coals, and includes the effect on blast-furnace production and practice. The test period involved is four months; the plants, Clairton by-product coke plant, and the Carrie No. I and No. 2 blast furnaces at Rankin, Pa., Carnegie-Illinois Steel Corporation. CLAIRTON BY-PRODUCT COKE PLANT AND COAL WASHER The Clairton by-product coke plant carbonizes 30,800 net tons of coal daily in 22 batteries containing 1482 ovens. Three oven sizes are used, commonly known as wide, medium, and narrow types, recognizing the difference in oven width. These ovens also differ in height and length. The present coal washer has a daily capacity of- approximately 14,000 tons, leaving 16,800 tons to be carbonized in raw form. Washed coal is used on all the narrow ovens and on three of the six batteries with ovens of medium width, raw coals being used on all the remaining ovens. The customary arrangement is

Jan 1, 1943

By O. Vartianen, R. T. Hukki

A preliminary investigation of the collecting effects of various fatty acids in tall oil has led to a conclusion that the collecting power of fatty acids used in flotation increases with increasing un- saturation of the hydrocarbon chain. Linoleic acid was found to be an excellent collector for oxide minerals. TALL oil is a mixture of fatty and resin acids extracted as byproducts in the sulphate pulp industry. In the field of flotation a well-known example of this type of product is Reagent No. 708 of the American Cyanamid Co. Its successful use as a flotation collector with many nonsulphide minerals has been described by Falconer and Crawford.' The composition of crude tall oil varies within wide limits.' " By a number of methods the crude oil may be refined to produce a variety of refined products. This investigation presents a preliminary comparative study of collecting properties of the fatty acids in tall oil. In Finnish tall oils these constituents are primarily palmitic, oleic, linoleic, and linolenic acids.:' The first is a saturated fatty acid having 15 carbon atoms in its hydrocarbon chain, plus one in the carboxyl group. The others have 17-carbon-atom chains and are unsaturated. It is of particular interest to note that palmitic, oleic, lino-leic, and linolenic acids represent increasing degrees of unsaturation with 0, 1, 2, and 3 double bonds, respectively. To test the collecting properties of the four fatty acids separately, the vacuum flotation technique described by Schuhmann and Prakash4 was used. By this method the boundary between flotation and non-flotation conditions was approximately delineated, with the use of ilmenite and several other minerals. Collector concentration and pH were the principal variables. On the basis of information obtained, actual flotation tests were run on an ilmenite-bear-ing ore in a laboratory flotation cell. Through the courtesy of P. Kajanne from the Department of Chemistry, Finland Institute of Technology, the following reagents were obtained for this investigation: 1—Palmitic acid, of Judex, had a purity of 95 pct as determined by parallel iodo-metric and spectrophotometric measurements. 2— Oleic acid, product of May and Baker Ltd., indicated purity of 98 pct. By iodometric and spectrophoto-metric determinations the oleic acid content was found to be 83.8 pct. In addition, it contained 6 pct linoleic, 1 pct linolenic, and 9.2 pct saturated fatty acids.' 3—Linoleic acid was prepared from soybean oil by low-temperature crystallization. Its linoleic acid content was 95 pct by the methods indicated above. 4—Linolenic acid was prepared from linseed oil by low temperature crystalIization. Its linolenic

Jan 1, 1954

By T. F. McCormick

THIS year, 1950, is the golden anniversary of the construction and operation in this country of a tube mill for the sole purpose of fabricating aluminum alloy tubing. For a short period prior to the beginning of this mill, aluminum alloy tubing was obtained from foreign sources or produced in mills fabricating other metals. Indeed, it was a very short period because aluminum itself was a newcomer in the field of metals. The first sheet rolling mill had been in operation just eight years and a rod rolling mill for the production of wire and cable had been functioning one year. The first tube mill for aluminum was built by the Aluminum Co. of America in May 1900 and started production with four draw benches and five men, including the mill superintendent. The building itself was a lean-to attached to a sheet-rolling mill at New Kensington, Pa. The cost of equipment, including the draw benches, dies, mandrels, and other tools, was about $5000. This figure seems absurd in the present day but nevertheless it was questioned at that time whether or not such a large sum should be spent to embark on a new and uncertain venture. The initial production system for the new mill consisted of casting round hollow ingots in a tilting-type iron mold, reducing the ingots to bloom size outside the plant, and finally drawing to size on the draw benches. This method of producing aluminum alloy tubing survived just two years, as blooms of satisfactory quality were not obtained consistently. It was superseded by the cupping method in which a 24-in. diam circle cut from a rolled plate was formed into a tube bloom using first a small cupping press and then a push bench. It was stated that tubing so produced was limited to a maximum diameter of 2 3/4 in. and to wall thicknesses varying from 12 to 24 gage. However, for the first time all the operations were performed at one plant and the result was a quality product. Later larger cupping presses and push benches were obtained and the method continued to be the principal one for aluminum alloy tubing for almost a quarter of a century. During the interim the use of a Alan Mannesmann -type billet piercer was explored and it was used to some extent, but failed to produce consistently a smooth inside surface suitable for drawing with aluminum alloys. Experiments started during the latter stages of World War I in the production of tube blooms with a hydraulic extrusion press, led to the use of this type of equipment to make tube blooms for further drawing during a change-over period extending from 1925 until 1930. At this time the cupping method was discarded completely. From these humble beginnings, the aluminum alloy tubing business expanded until well over six million pounds were produced in a single month in the United States during World War II. The major portion of this production was in strong alloys which did not appear in the tubing picture until 1022, when 17S alloy tubing was introduced for aircraft construction.

Jan 1, 1951

By D. Krammer, E. S. Machlin

The effect of a brior high-temperature creep strain on the low-temperature ductility of commercially pure nickel has been evaluated. The low-temperature (-196°C) ductility decreases linearly with an increase in prior high-temperature (920°C) creep strain. The effect is experimentally correlated to the formation of inter crystalline cracks and voids during the prior high-temperature creep strain. The magnitude of the effect is also believed to be a function of the notch sensitivity of the material. SEVERAL mechanisms have been presented to explain the process of inter crystalline cracking in metals undergoing high-temperature creep. zenerl has suggested that grain boundary relaxation of shear stresses could build up high stresses at ob- stacles to grain boundary shear and thereby nucleate a crack. Chang and rant' have experimentally demonstrated that cracks do form at obstacles to grain boundary shear such as lines where three grains meet. The role of vacancies in the mechanism of high-temperature inter crystalline cracking has been explored by Machlt with the conclusion that the nu-cleation of voids by vacancy condensation is almost

Jan 1, 1960

By H. Colijn

Belt scales are frequently used in the mining industry because of the ability to handle large tonnages without interrupting the material flow, fitting easily into all types of bulk handling systems and being relatively inexpensive. Although manufacturers claim weighing accuracies better than Y2%, many operators experience, in practice, much larger errors and they have become apprehensive about the use of belt scales. However, in spite of these disappointing instances, a belt scale is one of the most valuable tools for process and inventory control. Since it is a measuring device, care should be given to the design and installation of belt scales. The basic components of a belt scale are: (1) conveyor belt, (2) scale suspension, (3) sensing device, (4) integrating and recording. The first component of this system is of great importance to the overall accuracy and has been thoroughly discussed in earlier papers. This paper will review primarily the various scale hardware designs currently available, and will be confined to the last three components of the system.

Jan 1, 1973

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By H. W. Gillett

Many of the parts of motor cars, aircraft, etc., that require strong light construction, hence must be made of high-quality steel, are stressed to the maximum limit only in a very small volume. In parts subject to bending stress a line or even a point may take the maximum stress. A series of endurance tests under repeated bending in progress in the U. S. Bureau of Mines laboratories, like similar tests by other investigators, has shown the great difference in life of sister bars of the same stecl, handled in the same way and tested at the same nominal stress. It is known that a surface notch or scratch greatly increases the local stress over the nominal calculated stress; internal notches, such as those formed by inclusions or sonims, probably have a similar effect. From the tetss made by the Bureau of Mines, the cleanliness of the steel at the dangerous section, or point of maximum stress, seems to be one of the most important factors in determining the life of the piece. The more localized the stress, the more does chance, rather than the average properties, dctermine the life of the steel. The usual test, a tension test of a bar taken longitudinally, is not sensitive to the local drop in strength (or tendency to increase the true local stress over the nominal) because of inclusions, which probably have a more injurious effect in hard heat-treated steels, such as must be used when great strength is sought, than in softer steels. Users of steel who make transverse tests find surprisingly low ductility on transverse bars of dirty steel, though the longitudinal tests may be good. Bending tests, reverse bending tests, and notch-bar impact tests,

Jan 1, 1923

By L. C. Uren

THE resistance to flow of mixtures of gas and oil in passing up through the flow tubing of oil wells operated by gas-lift or by natural flow is a factor in oil-recovery technic that has received but little attention. Yet accurate design of a tubing installation for a particular set of conditions, where operation is by either of 'these methods, is impossible without quantitative data on the pressure loss suffered by the oil-gas mixture in its passage through the well tubing to the surface. Because of lack of such information, petroleum production technologists have been compelled to approach this problem by "cut-and-try" methods, which, doubtless in many cases, has resulted in the installation and use of tubing too large or too small for most efficient utilization of the expansive force of the gas used in lifting the oil. Impressed with the necessity for information of this character, the authors have conducted a series of tests with large-scale apparatus in the petroleum engineering laboratories of the University of California, designed to be productive of data that would afford a means of attacking the problem of flow-tubing design on a more scientific basis.

Jan 1, 1929

By R. M. Leibrock, C. W. Ziemer, R. P. Vincent

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By W. D. Steele, S. D. Brady

The Pittsburgh coal seam in West Virginia contains the largest coal reserves of any coal seam in that State and is, therefore, one of the most important seams, and attains minable thickness and purity throughout that part of the seam extending from the Northern Panhandle to Monon-galia Co. thence south and southwest across the state to Wayne Co. near Hunt-ington. The Pittsburgh coal is also minable in the Upper Potomac region but is now practically exhausted there. The total minable areas of this coal amount to 2,165 sq miles and are estimated, by the West Virginia Geological Survey, to contain 13¼ billion net tons. The largest body of Pittsburgh coal outcrops on the western edge of West Virginia, along the Ohio River as far south as Moundsville, West Va., going under the river at that point and extending at various depths down the river as far as Wetzel Co. line where it thins out to such an extent that it has little practical value, and on the eastern edge this large body outcrops along the Monongahela River. The territory to be covered by this paper is the area known as the Northern West Virginia District comprising Wetzel, Mon-ongalia, Marion, Preston, Harrison, Dodd-ridge, Taylor, Barbour, Upshur, Lewis, Gilmer, Braxton and Calhoun Counties, and is also known as Dist. 3 under the Bituminous Coal Act. This region was originally opened for commercial mining along and adjacent to the Monongahela River around 1852 when the Baltimore and Ohio Railroad was constructed to Fairmont. It has been extensively developed, first, in 1880 (when the Monongahela River Railroad, now B. & 0. R. R., was constructed) between Fairmont and Clarksburg, and later, in 1916, between Morgan-town and Fairmont when the Monongahela Railway was constructed and placed in operation, this area furnishing the major portion of the production over the past years. With the mining out of a great deal of this territory adjacent to the Mononga-hela River considerable interest has been developed in the back acreage; and within the past few years a number of diamond core drill holes have been made in the back areas of Monongalia and Marion Counties. In this back area the oil and gas well drilling showed that the Pittsburgh coal seam was of minable thickness and ranged in depth from 350 to 1,000 ft below the surface of the stream valleys but this drilling did not furnish any definite data as to its thickness and quality. Economic Importance The Pittsburgh seam in Northern West Virginia is of primary importance as a coal resource not only because of its large reserves but because of its contributing a very large part of the coal used in this country for general steam uses. The Pittsburgh seam is a consistently thick seam, averaging 8 ft in thickness, with very easy grades underground, so it has always been

Jan 1, 1949

By R. M. Leibrock, R. P. Vincent, C. W. Ziemer

The Stanolind flowmeter, which employs a hot-wire anemometer connected in a Wheat-stone bridge circuit, has proved useful for determining the relative productive ability of individual sand members of gas wells. The operation of this instrument in measuring gas velocities in the well bore above each producing member has provided both a direct and accurate means of analyzing reservoir performance. Results of tests conducted with the well flowmeter in the Hugoton gas field of western Kansas have indicated some rather unusual production characteristics. In two cases it was found that all or the greater part of the total gas produced was coming from one section in wells where four "pay" sections had been perforated individually. These actual measurements contradict in many instances the indications of data obtained from electric logs and from core analysis; the fact that these latter sources often give incorrect results, demonstrates the necessity of a method, such as is provided by the well flowmeter, for accurately determining the amount of gas coming from each producing member. Introduction In any gas well where a number of pay sections have been perforated individually and are producing to a common outlet, the question arises as to the relative amounts of gas being passed through each set of perforations. In the past it has been the policy to depend on core analysis to estimate relative productivities, or, where the sections were not cored, to obtain some idea of production characteristics from electric-log studies. The weaknesses in these methods are readily apparent and indicate the need for more reliable means of measuring gas flow from each zone. The Stano-lind flowmeter* was developed for this purpose. Preliminary tests were made with the instrument in the Katy gas field near Houston; however, the bulk of the routine work with the well flowmeter has been confined to the Hugoton gas field in western Kansas, where results obtained have been encouraging. A description of the instrument, the field technique employed in testing, and a few of the results obtained in the Hugoton area are discussed in this paper. Description or Instrument The well flowmeter is 1¾ in. od and 7 ft long; it is entirely self-contained, can be run through tubing as small as 2 in. id in wells with high pressure (4500 psi) and temperature (210°F) and is lowered on a wire line commonly used for other instruments of the bottom-hole type at falling rates up to 500 ft per minute. It will detect gas flow as low as 10 ft per minute linear velocity, and yet withstand and record velocities of 1000 ft per minute without damage to the detecting element. Killing the well is not required nor desirable for running a production profile when using the instrument, and it is necessary to stop flow for only a short time. The detecting element of the instrument is a hot-wire anemometer connected in a

Jan 1, 1948

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By Mark Alling

INTRODUCTION A FEW years ago, gravel mining in the ancient river beds of Sierra county was the principal industry of the county. Operating drift mines were very numerous and many large hydraulic mines were in action. Eventually the State laws put an end to hydraulic mining, it being claimed that the silt carried down the streams to the valleys filled the rivers and caused winter floods, which were damaging to the surrounding farms. The ancient river deposits which could easily be found were, in the course of 40 years, worked out or practically so. The prohibition of hydraulic mining was a severe blow to the industry in general. The deposits were not developed and the gravel-mining industry practically stood still for many years. In Sierra county, nearly all the hydraulic mines were at the points where the ancient channels were exposed to view by reason of the modern stream erosion, or, in the miner's language, where the channels "enter" or "break out of" the ridges. The claims covering them also covered large areas in which were long segments of lava-capped channels, suitable for drift mines, and the points being hydraulicked were usually the controlling points of attack. Men who have followed hydraulic mining for any length of time seldom are content to work a drift mine. Knowing the great value of their deposits and feeling that they had been robbed by the State, these men have stubbornly held to their claims. The gold that is carried in these gravel channel deposits is more or less scattered throughout the depth and width of the deposit; the percentage that can be recovered by the process of drifting ranges from 50 to 75 per cent. of the total. In hydraulicking, practically all of the deposit is put through the sluices, and as the cost per cubic yard is only about 10 per cent. of the cost of drifting, the deposits, if classed as hydraulic mines, are much more valuable than if classed as drift mines; hence the old timers have held their claims (now worthless as hydraulic mines) at prices which the drift-mining industry could not stand; and such mines

Jan 7, 1914

By F. W. Apgar

THe valuable results that have followed the application in recent years of microscopic methods of research to problems of ore genesis have been significant, but possibly the recognition of their practical importance is not as general as might be, and while, as a scientific method of investigating ores and rocks, the advantage derived through the use of the microscope is unquestioned, its utility as an aid in solving mining problems arising during actual every-day mine examination and operation may not be fully appreciated. Perhaps the most logical method of showing some of these practical applications of the microscope will be to consider first the prospect stage of a mining venture, then the uses to which the instrument may be put during the operation of a working and developed mine, arid, finally, to discuss some of the problems of a metallurgical nature that may arise during milling and smelting the ore. The valuation of mining property as a preliminary to acquiring ownership or determining the advisability of investing time and money in an enterprise is one of the most important and delicate problems that come before the mining engineer. The many and variable factors that have to be taken into account, as, for example, the geology of the district, availability of supplies, probable mining costs, transportation facilities, and the quality of ore, require a careful balancing of costs against recoverable values. Primarily, however, a study of the local geology is of first importance, since, in a prospect with little development work, the question of character and probable quantity of the ore and its value can only be approximated with any degree of accuracy by a thorough investigation of geologic conditions, and a general knowledge of ore deposits. Unless these are favorable and pay ore reasonably certain, other factors need not be considered. The character of the outcrop, evidences of mineralizing agencies in the adjacent rocks, and geological structure, are the data of chief significance.

Jan 1, 1914

By Esteban Domic, Eugene O. Brimm

The Lo Aguirre ore deposit of Sociedad Minera Pudahuel is expected to have a life of 12 years, producing 16,500 mt per year of copper cathodes. The total copper content of the ore ranges from 2% in acid-soluble form to 2% as sulfides. Sociedad Minera Pudahuel chose TL leaching, solvent extraction, and electrowinning as the processing steps to give low investment and operating costs. Design and operating criteria of the TL leach plant have been obtained in an experimental program carried out since 1974. Bench scale tests indicated that 90% of the oxidic copper and 35% of the sulfidic copper could be extracted to give 5 gpl copper by treating crushed ore with acid, curing, and rinsing in a column with a dilute acid solution containing ferric sulfate which is requllred to solubilize the sulfides. These results were verified in a pilot plant which combined leaching, solvent extraction, and electrowinning. Raffinate was recycled to the leaching circuit after oxidation to regenerate ferric ion. Refinements in the processing have resulted in significant improvements in extraction to give 95% to 98% recovery of the oxidic copper and 55% and 60% of the sulfidic copper. The plant is expected to give this degree of recovery. As a consequence, the original plan to include a concentrator in the plant has been abandoned.

Jan 1, 1980

By L. H. Wolfe, J. O. Thieme

The tensile and shear strengths of frozen soil and the compressive strengths of ice and frozen soil were measured These tests showed that the strength of ice and of frozen soil increased as the temperature was decreased. A method is presented for the measurement of thermal conductivity and specific heat of earth and ice. Using the parameters thermal conductivity, specific heat and density, the thermal diffusivity was calculated. Results of thermal property tests establish water as the major variable contributing to thermal property values. INTRODUCTION During the last few years, a considerable interest has developed in underground storage of cryogenic liquids such as liquid natural gas. Because of its economy and safety, underground storage is being used. Before underground caverns could be seriously considered, however, the strength and thermal characteristics of the soil had to be obtained. Methods are presented herein for measuring tensile, compressive and shear strengths, specific heats and thermal conductivities. The tests were performed on two soils at temperatures from ambient to -195C. Because it is difficult to find data in the literature that pertain to a particular soil, ice was used to evaluate some of the experimental procedures. Some of our ice data are compared to the published values. PHYSICAI, PROPERTIES SOIL SELECTION AND SAMPLE PREPARATIONS The physical and thermal tests were performed on recompacted samples of two typical soils that might be encountered in underground caverns: a gray, fire clay that had been pulverized and mixed with water into a pliable mud; and a brown, sandy silt that was dug from a dry river bank and subsequent1y mixed with tap water. The moisture content of the test specimens was 17 to 22 per cent (based on the wet weight of the soil). This amount of water nearly saturated the silt, but the clay was well below the saturation point. The soils are partially described by the sieve analyses (Fig. 1) which show the particle size distribution of the coarser than 44 micron portion of the soils. The curves also show that approximately 75 per cent of the clay and 20 per cent of the silt are finer than 44 microns. The particle size seems to affect some of the physical properties, and the finer than 44 micron portion is important in the thermal conductivity test. Physical specimens were cut with a bandsaw from frozen blocks of the soil. The specimens were then sanded and kept frozen until after they were tested. They were stored at the approximate test temperature for several hours. Then, to equilibrate the samples to the test temperature, they were stored at the temperature at least an hour before they were tested. TEST EQUIPMENT An Instron, which is a constant speed gear-driven instrument, applied force to the samples and drew stress-strain plots of the test. All of the samples were strained at 0.02 in./min. All of the physical tests were conducted in a temperature cabinet that controlled the temperature to 1C. TENSILE STRENGTH Briquette or "dog-bone" shaped tensile specimens were pulled with suitably shaped jaws. This shape of specimen, which is usually used for tensile tests of concrete, is satisfactory for testing frozen soils except that the samples tend to

Jan 1, 1965

By R. A. Bloom, John Birtalan

CONSIDERABLE interest has been shown in recent years toward determining the crystal structure, mode of formation, and chemical composition of the x phase, designated as such by Andrews,' who was the first to establish its presence in Fe-Cr- Ni-Mo alloys . Later work2 by the same author has shown that the occurrence of x depends on the presence of some molybdenum in the alloy. The phase, which appears to be identical or very similar to a manganese, has a body-centered-cubic structure and is closely related to s phase. Koh observed a similarity in composition between x and s and speculated as to whether x might be an ordered structure of u which is known to have a tetragonal crystal

Jan 1, 1957

By H. I. Smith

The technical and safety press have devoted much space in support of or in opposition to the use of booster and auxiliary fans in coal mines. The Mine Safety Board of the U. S. Bureau of Mines has given the matter consideration, and the Mine Ventilation Committee of the A. I. M. E. is now seeking a discussion of the merits and demerits of such fans to guide it in formulating recommendations. In this paper I will set up some principles on which I believe most engineers will agree and from which we may work toward a decision, though as to what that decision shall be there may be a difference in opinion. Before stating the points on which I believe there is accord, I will distinguish between booster and auxiliary fans. Definition of Booster and Auxiliary Fans In discussing underground fans G. S. Rice1 distinguishes between those used to increase the amount of air passing a given point and those used to augment the ventilation locally. He describes a booster fan as one which is installed to handle the entire air current passing a given

Jan 1, 1927

By H. A. Wriedt

Zinc-vapor pressures in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C were measured by an isopiestic method. Thermody-na?nic properties of zinc in these solutions were derived directly and those of iron with a Gibbs-Duhem integration. Zirzc and iron exhibit large, positive, and moderately temperature-sensitive deviations from ideality. Excess enthalpies and Gibbs energies are positive in the ranges studied. It has been establzshed in relating published phase equilibria to the Gibbs energies of forming solid solutions that positive departures from ideality also exist in the fcc solutions. Tlze stability, as defined by Darken, of the bcc solutions is small but positive at 703.5"C. Its decrease with decreasing temperature indicates that a miscibility gap may exist in the stable or metastable bcc solutions at lower temperatures. The changes of thertnodynanlic properties relatable to changes in magnetic state are minor compared to other changes due to alloying. The accuracy with which the relation between lattice parameter and composition of the bcc solutions is known has been improved. Zinc increases the lattice parameter of a iron by O.ZOZA per unit atom action zinc to at least NZn = 0.25. TO our knowledge, only Ciganl has previously investigated thermodynamic properties of the bcc solutions of the Fe-Zn system. He measured zinc-vapor pressures in the temperature range from about 320" to 360°C by an effusion technique. We have measured the vapor pressures of zinc in equilibrium with bcc solutions of zinc and iron at 703.5", 757", 793", and 900°C by an isopiestic technique. This investigation and the pursuant thermodynamic computations are part of a program for studying several properties of these solid solutions. In the appendix we report a remeasurement of the relation at room temperature between the lattice parameter and zinc content. Related work not reported herein embraces measuring the diffusivity2 of zinc in ferrite at 700" to 900°C and the Curie point temperature3 as functions of composition. EXPERIMENTAL METHOD AND APPARATUS Purified iron at a series of constant temperatures was saturated with zinc at a series of constant zinc-vapor pressures, the range of conditions being so limited that the equilibrated solid solutions were ferri-tic. The equilibration was conducted in long capsules, Fig. 1, that had been evacuated, gettered with titanium, and sealed. The purified iron, part of a vacuum-melted ingot of electrolytic-iron stock (Glidden Co. 1044-grade), had the impurity contents listed in Table I. It was used in the form of millings about 0.001 in. thick. A zinc of 99.999 pct purity (United Mineral and Chemical Corp.) and later one of 99.9999 pct purity (Cominco Products, Inc.) were used, with no observed difference in results. Sufficient zinc was placed in the capsule (separate from the iron and kept at a different temperature) to supply the vapor phase and the iron alloy, while leaving a pool of pure liquid zinc throughout the run. The imposed temperature of the residual zinc pool fixed the vapor pressure of zinc throughout the capsule; condensation was avoided at other locations by making this the lowest temperature in the capsule. Two common complications of nonisothermal systems were, we believe, effectively absent from ours: first, molecular species other than monatomic have no appreciable concentration in zinc vapor at 700" to 900~~: second, the development of zinc-pressure differentials in the capsules was suppressed by use of relatively large-diameter tubing and the absence of diluents in the zinc vapor other than desorbed impurities. The specimens and zinc pool were located at two isothermal zones (each ranging within 1°C over several inches) of a wire-wound, 37-in.-long vertical-tube furnace. The required temperature distribution was achieved by external adjustment of the currents in three electrically isolated windings. The temperatures of the isothermal zones were controlled independently by ther-

Jan 1, 1968