Search Documents

By Efrem R. Reeves, David C. Byrne

This study was conducted as part of a project involving the evaluation of a new type of noise exposure monitoring paradigm. Laboratory tests were conducted to assess how “nonstandard” dosimeter microphones and microphone po­sitions measured noise levels under different acoustical condi­tions (i.e., diffuse ?eld and direct ?eld). The data presented in this article re?ect measurement differences due to microphone position and mounting/supporting structure only and are not an evaluation of any particular complete dosimeter system. To varying degrees, the results obtained with the dosimeter microphones used in this study differed from the reference results obtained in the unperturbed (subject absent) sound ?eld with a precision (suitable for use in an ANSI Type 1 sound level meter) 1/2 -inch (12.7 mm) measurement microphone. Effects of dosimeter microphone placement in a diffuse ?eld were found to be minor for most of the test microphones/locations, while direct ?eld microphone placement effects were found to be quite large depending on the microphone position and supporting structure, sound source location, and noise spectrum.

Recent developments in diamond drilling practice have been chiefly 'concerned with modifications in drill design and 'operating technique whereby an increase in daily footage rates and reduced footage costs have been achieved without any marked improvements in the recovery of core. This trend is perhaps due to the general acceptance by the mining and drilling engineer alike of the belief that diamond drilling has definite limitations in exploratory work on mineral deposits characterized by irregularities in continuity and grade, such a belief arising from the fact that drilling technique has not yet evolved coring devices to ensure the full recovery of the rock and mineral formations penetrated.Current diamond drilling operations at Moonta and Wallaroo Mines, carried out by the South Australian Department of Mines, have attained remarkable results in completely eliminating core-loss by the use of a special double-tube core barreI.It is considered that assays of borehole samples taken with this special barrel have a reliability comparable, if not superior to that of similarly situated mine samples and, provided they are spaced satisfactorily, can be used as, a basis for calculating tonnage and grade. Formerly, with only partial core-recoveries, positive borehole results on narrow irregular lodes, such as those in the Moonta and Wallaroo Mines, could be accepted mainly as indications of the presence of mineralization, and could have only a limited bearing on estimates of ore reserves.The value of this special double-tube core-barrel lies In the fact that it guarantees good core recovery and, therefore, good samples, and eliminates the need for sludge-sampling, which is prone to give unreliable assay results from several causes, such as gravity concentration in the bottom of the hole and return water losses which cannot be overcome.In view of the increasing demand for minerals and the probability that the search for them will be carried on largely by boring, it is felt that it would be of interest and value to direct the attention of mining engineers to core-recovery results obtained by diamond drilling plants in South Australia and the features of the special core-barrel, designed by the writer, which has made this possible. Also, the writer is desirous of placing on record two other core-recovery devices designed to extract accurate samples in relatively soft or unconsolidated formations. The latter are used with percussion and calyx plants, respectively and their value has been proven on phosphate rock and coal deposits in South Australia.

Jan 1, 1943

By D. Brand

"The risk management objective of the AMIRA Code of Practice for Metal Accounting has seldom been systematically investigated in the literature up to the authors’ knowledge. Risk is defined in the Australian Standard on Risk Management (AS/NZS 4360:2004), as “the chance of something happening that will have an impact on objectives”. The simplified economic analysis performed in this paper has lead to define “something happening” as measurement non-representativity and “impact on objectives” as NSR loss from the optimal NSR. This has pinpointed a missing link being the establishment of a relation between NSR in flotation plants and measurement representativity. The proposed framework, referred to as the total cost of representativity, answers the previously unanswered question of how much accuracy/reproducibility is fit for purpose in a given flotation plant. Authors readily acknowledge that it is way easier to assess the cost of accuracy/reproducibility than the cost of inaccuracy/irreproducibility. However, this exercise not only answers previously unanswered questions but also establishes an essential link with operational excellence. This paper exposes why such operational excellence could neither be attained nor proved without a state of the art metal accounting system. This should impact not only how metal accounting systems are audited/designed/refactored, but also how flotation plants are designed.IntroductionBecause representative metal accounting is a vital source of information for the financial accounts of a mining/metallurgical company, the need for a code on metal accounting was recognized in 2001 and a team was formed in 2003, under the sponsorship of several major mining houses, to produce such a code. Table 1 exposes the two main objectives of this AMIRA Code of Practice for Metal Accounting."

Jan 1, 2017

By G. S. Hill, B. J. Huls

This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed the authors to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flowsheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit.

Jan 1, 2006

By D. M. Avant, S. M. Pickering

A variety of grades of very white muscovite mica are now being produced from sedimentary sands and clays in Central Georgia. The mica is naturally concentrated near the base of the lens-shaped kaolin deposits and also disseminated in associated quartz sands. The same weathering and bacterial alteration processes which have transformed the kaolins from dark organic muds to white pigment-grade industrial clays have also removed discoloring iron from the micas and developed unusually white muscovite. Further, chemical alteration has removed some potassium from the muscovite atomic structure, resulting in an easily delaminated mica which can be cleaved to unusually fine, high bulking, high aspect ratio products. The peculiar alteration history of these sedimentary micas enables production of some of the whitest, finest particle size, and thinnest aspect ratio muscovite mica products on the world market today. Raw mica feed is obtained from kaolin and sand processing by-products, and also from beneath the useful base of abandoned kaolin mines. The processed ultrafine and filler grade muscovite mica products are used for paint, plastics, cosmetics, mold release, thermal and electrical insulation, epoxy, and dry wall joint cement markets.

Jan 1, 2002

By M A. Mongillo

Most geophysical and geochemical data collected during regional exploration programmes are in vector form (location, value), and have traditionally been presented and interpreted in a profile or contour map format. However, the human vision system can interpret data presented in image format much more easily and new information is often revealed by the judicious application of powerful interactive computer image enhancement techniques. This paper describes a practical demonstration of the application of such tools to gravity and resistivity datasets from the Central Volcanic Region of theNorth Island.   Filtering, contrast enhancement, relief shading, pseudo-colouring and then overlaying of the gridded datasets in image format has helped identify inter-relationships such as the association between many low resistivity anomalies (epithermal deposits or geothermal resources) and the edges of large gravity anomalies (calderas or grabens). Similar revelations should result from the application of these tools to the integration of other mapped datasets from geophysical, geochemical and geological disciplines.

Jan 1, 1992

By John P. Turner

The behavior of tieback retaining walls depends on many factors, including soil properties, groundwater conditions, construction sequence, spacing and stiffness of tiebacks and soldier piles, tieback loads, and others. The primary design considerations for tieback walls are 1) adequate stability and 2) limiting wall movements. Traditional design methods rely on apparent earth pressure diagrams and experience to predict the forces which must be supported by the tiebacks to provide adequate stability. The required soil properties depend upon whether the soil is sand, soft clay, or stiff clay. Design to limit wall movements is more difficult and the usual approach is to design the wall with an adequate factor of safety for stability and then evaluate wall movements during construction through the use of load tests on individual tiebacks and monitoring of wall movements by optical surveying, slope indicators, and extensometers. If excessive movements are likely to occur, it is often not known until construction is well underway. This approach is reflected in the fact that few tieback walls fail due to a lack of adequate stability, while most litigation involving tieback wall performance is related to excessive movements. Much progress has been made in recent years in methods for predicting the movement of all types of insitu retaining walls (Clough et al. 1989, Clough and O'Rourke 1990). These methods are based upon both experience and analytical methods. This paper reviews the methods currently available for evaluating both the stability and movements of tieback retaining walls. Case histories involving excavations constructed in the downtown Seattle area are used to evaluate the applicability of the available methods to Seattle conditions and to illustrate the importance of soil behavior in tieback wall performance.

Jan 1, 1990

The placer mining industry of the West Coast region of the South Island is based largely around the production of alluvial gold, although other valuable minerals are also present. Since the first major discoveries in 1864-65, reported gold production has totalled around 264 t (8.5 Moz). During the past 10 years, annual production has totalled around 1460 kg (47,000 oz). It is anticipated that gold production over the next three years will continue at a level of 1400-1800 kg.   Annual gold production peaked during 1866 at approximately 17,170 kg (550,000 oz) and has not exceeded 100,000 oz since 1885. This reflects the ease with which gold was won from shallow, rich deposits that were present at many localities. Subsequently, there has been a general decline in the availability of this type of deposit, a trend that will continue in the future. This paper outlines the present state of placer mining in the West Coast region, gives some historical background to the industry and briefly predicts future trends.

Jan 1, 1997

By H. Copur

Experimental studies for quantification of force and brittleness indices relevant to rock cutting performance are presented. A simple interpretation method is developed, which quantifies the force-penetration response obtained from indentation tests. Basic parameters of the quantification are force increment and decrementrates, force increment and decrement periods, and number of increment and decrement data points. Blocks of eleven different rock samples were collected from different operating mines in Turkey and subjected to indentation tests to calculate the indices. The samples included harzburgite, serpentinite, trona, limestone, claystone, two different sandstone samples, siltstone and three different chromite ore samples. The concept was validated by a set of full-scale linear cutting tests using a conical cutter for measuring the cutting performance in relieved and unrelieved conditions, i.e. cutter forces, specific energy, size distribution of rock cuttings. The rock cuttings were sieved to determine coarseness index, indicates coarse chip generation characteristics, and size distribution. The force index is moderately correlated with the cutting performance and mechanical properties of the rocks, and poorly correlated with the coarseness index and size distribution of cuttings. A general and moderate trend is observed between the brittleness index and the coarseness index, cutting performance for unrelieved cutting conditions and mechanical properties of the rocks. However, additional data is required to fill the data gaps and to potentially establish relationship between the brittleness index and all other parameters.

Jan 1, 2003

By Grant R. J. Bearss

Due to environmental concerns in urban construction, many typically simple projects become very complex or feasibly impossible. The introduction of relatively new concepts has redefined "impossible", again simplifying these projects and making them "possible". Case Study One covers the use of Pressed-in Tubular Piles on portions of the Long Island Expressway in Queens, New York. Innovations in the design, material and installation method solved many typically inherent problems on projects of this type and resulted in cantilevered walls that supported a 35ft (10.668m) excavation. Design predictions and actual measured deflections of this wall were within millimeters. Case Study Two covers the use of Pressed-in Tubular Piles on portions of the Hodogaya Bypass in Yokohama, Japan. Innovations in equipment development allowed for a cantilevered retaining wall to be constructed without affecting the adjacent right-of-way, dramatic reduction of the overall construction duration and installation of tubular piles in soils with SPT N values greater than 160.

Jan 1, 2002

By S. Ndlovu, M. Malatse

"The Witwatersrand Basin is the heart of South Africa’a gold mining industry. The cluster of gold mines located in the Witwatersrand Basin generates a significant amount of mine tailings, which have adverse effects on the environment and ecological systems. In addition, disposal costs are very high. The exponential population growth in the Witwatersrand area has resulted in pressure on the reserves of traditional building materials. Quarrying for natural construction material is very expensive and damages the landscape. This work therefore examines the use of gold mine tailings in the production of bricks.Different mixing ratios of gold tailings, cement, and water were used. The resulting bricks were then cured in three different environments - sun dried, oven dried at 360°C, and cured in water for 24 hours. The bricks were then tested for unconfined compressive strength, water absorption, and weight loss. The results showed that the mixture with more cement than tailings had a compressive strength of approximately 530 kN/m2. It was also found that the best brick curing system was in a water environment. Bricks made from tailings cost more than conventional bricks because of the higher quantity of cement used, but the manufacturing process consumes less water. Overall, the results indicated that gold mine tailings have a high potential to substitute for the natural materials currently used in brickmaking.Paper written on project work carried out in partial fulfilment of BSc. Eng. (Metallurgyand Materials Sciences)"

Jan 1, 2015

By Cosmin Carpinisan, Erich J. Hofmann, Stephen J. Hall

"Since presenting a technical paper regarding their unique capabilities in Forged Steel Mill Gearing at the SAG-2006 Conference, Australian heavy engineering company Hofmann Engineering has pioneered a number of new manufacturing processes and design concepts for components of large comminution equipment. These include: 1. Novel design improvements for HPGR Rolls with forged steel tyres and a unique patented tungsten carbide insert designed to improve wear life, enhance autogenous layer build-up, and to reduce breakage & chipping under load. 2. Development of forged fabricated Mill Heads using rolled & welded high-tensile steel plate as alternatives to cast conical mill heads. 3. Insitu Girth Gear measurements for profile and wear via portable 6-axis CMM. 4. Gear and Pinion designs to AGMA-6114 for SAG mills of 38’-40’ diameter to 24MW and for Ball Mills of 26’ diameter to 18MW. The paper presents case studies from the Australian heavy manufacturing facilities of Hofmann Engineering, combined with news of their new gear manufacturing and gearbox overhaul facility in Canada."

Jan 1, 2012

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By T. J. Serenko

The epithermal deposit is hosted by Tertiary volcanic rocks that lie between mid-Miocene normal faults of the Northern Nevada Rift. Petrographic, laser-ablation and metallurgical observations suggested that the gold occurs in two principal forms: native (and electrum) and disseminated in arsenopyrite. It was proposed that gold is distributed between two parageneses with distinct mineralogical associations. Detailed downhole geochemical study supported the observations. Concentrations of Au, Ag, As, Sb and Se were determined from drill core and reverse-circulation cutting composites and contoured on cross-sections. Gold was indeed shown to have a bimodal distribution with the two parts separated spatially and perhaps temporally, implying that two separate genetic processes acted to concentrate gold at Mule Canyon

Aug 1, 1995

By M. Leslar

Slope monitoring has been an important issue in static terrestrial lidar for some time. Several solutions for monitoring the progress of a slide have been devised over the years. All of these solutions have required users to be in the field operating the lidar equipment. This paper presents a new system developed using the Optech ILRIS-HD or ILRIS-LR lidar and the scripting language of PolyWorks to produce an autonomous slope monitoring system. This system has proven invaluable in detecting and alerting mine workers to potential danger within their mine sites. It has already been deployed in two mine sites and is scheduled to be installed at a third.

Feb 27, 2013

Considerable improvements in diamond drilling equipment have been made since the early 1950s. A recent drilling programme, however, at Williamtown, near Newcastle, carried out by the Joint Coal Board on behalf of the Electricity Commission of New South Wales, emphasized deficiencies in existing equipment when particularly diflkult coring conditions were encountered.Spurred by unacceptably low recoveries in coal seams in this area, the Joint Coal Board devised and developed, with the assistance of the Electricitv Commission, a new typc core lifter and a special 26 ft triple tube core barrel, designed to operate in conjunction with it in bad coring conditions.The core lifter, whieh is propped open clear of incoming core during drilling, is activated by fluid impulses generated inside the core barrel. It can be used with double tube barrels when drilling firm rocks whichdo not change diameter by compaction inside the barrel.Softer rocks. such as clayey types, require the use of a rriple tube barrel.Results from testing carried out to date in difficult areas in New South Wales coalfields have shown that greatly improved results can be obtained with the new equipment. Although developed essentially for coaldrilling, the new core lifter and barrel could be adapted to other fields of diamond drilling. Even in areas where no great coring difficulty is encountered the cost advantage deriving from the greatly inereased life of the core lifter and the adaptor in which it is housed could justify its use.

Jan 1, 1967

By D. D. Blue

To insure domestic production of aluminium for, essential civilian and defense uses, the Government, under authority of the Defense Production Act of 1950, programed and promoted an aluminum-expansion program that will more than double the primary production capacity that existed in 1949. In view of this vastly increased production, the raw materials, with respect to both quantity and sources, are reviewed. The raw-material consumption pattern, the requirements during an expansion period when excess quantities of materials for starting up new facilities are consumed, and the probable requirements for production of 1.7 million tons per year of primary aluminum are discussed. The raw materials that presented the most difficult supply problems were bauxite, electrical power, and fluoride salts, and the supply pattern for these materials probably will undergo changes. A major part of the electrical energy for the increased capacity was to come from thermal generation, Jamaica-was to become a major source of bauxite, and synthetic fluoride salts were replacing natural cryolite in increasing quantities. Other raw-material requirements discussed are: Soda ash; lime, and limestone; starch; filter cloth; fuel; alumina; the carbonaceous materials, green and calcined petroleum coke, high-and low-temperature pitch and coke or anthracite; cryolite; aluminum fluoride; the materials going into production of synthetic fluorides, acid-grade fluorspar, and sulfuric acid; and labor. INTRODUCTION The raw materials for the aluminum industry that have received the most publicity are bauxite, the ore that supplies elemental aluminum, and electrical energy, the means by which aluminum oxide is reduced to metal. A number of other important materials are, however, required in large quantities in the production of primary aluminum metal.

Jan 1, 1954

By P Taskinen, D Lindberg

The increase in metals demand in the electrifying globe means significant growth in the smelting of copper, nickel, zinc, and lead, produced from primary sulfide sources or using sulfide mattes as the intermediates of the process chains. This means that leaner and complex mineral deposits will be evaluated as ores and are in the future traded in the commodity market for smelting and refining to pure metals. An important issue in the trend is the technology metals, like antimony, tellurium, and gallium, which exist as trace elements in sulfide ores and form no ores of their own. Their recovery becomes important in the coming decades as will be the case with growing slag amounts without use in other industries. The key is to produce environmentally acceptable slags in the smelting operations. It sets new boundary conditions to the treatment of flue dusts. This means that all material streams of smelting and refining must be re-evaluated for the deportments of the main and minority metals. In copper smelting, the recoveries of precious metals are today important for the feasibility of the custom smelters but due to low prices of many minority metals they are discarded in slag landfills. It is one of the emerging issues also in the secondary copper smelting today and once the demand grows, the same question will be faced also in the mining-beneficiation-smelting-refining chain of the primary production of nickel, zinc, and lead. The distributions of many technology metals in the copper and nickel smelting have been recently studied using methods where the chemically bound trace elements in the slag and its phases at the smelting conditions have been studied. Thus, the key data about options for process modifications and additional processing steps are piling up. Short processing routes in the metals smelting and refining are attractive due to their simplicity. At the same time, complexity of many raw materials challenges the fluxing at high oxygen partial pressures in low silica slags with high metal concentrations. The compromise between high primary recovery and safe operation is a demanding task in conditions where slag foaming outside the processing window is evident. The increase in the demand of pure nickel is challenging the raw material basis where low-grade sulfide ores are soon smelted along with nickel laterites to matte. It is a demanding task at high MgO concentrations. The low solubility of MgO in iron silicate slags requires new fluxing strategies and new smelting end points for the operation at reasonable temperatures; the direct nickel matte smelting in one-matte mode may be an option.

Aug 21, 2024

Some 50 miles of tunnel have been driven in the Snowy Mountains Area since tunnelling commenced in 1951. Hates have improved progressively due to the know-how of American supervision and use of large matched equipment of modern design.The work has been carried out by contractors, working almost exclusively under schedule of rates contracts. The Authority has maintained active research into tunnelling problems, especially that of support, and this has resulted in considerable economies and improved rates of progress. The contractors also have sought economies both by management and equipment techniques. Ammonium nitrate came into favour as an explosive essentially because of its lower cost, and handling techniques have improved progressively. Rock conditions preclude use of the "Mole" type equipment in its present stage of development, but one contractor introduced the "sliding floor" and this could exert a great influence on future tunnelling methods.Examination of tunnels that have been in service for some time confirmed the quality of the work and endorsed the policy of continued research and development.GENEHALThe Snowy Mountains Scheme provides for the diversion of the Snowy and Eucumbene waters through two transmountain tunnels to the western river systems. These diversions, together with additional regulations provided for waters already flowing inland, will provide an average additional discharge of 1,818,000 ac it per year for irrigation.Furthermore, approximately 6,000 million kWh of electrical energy will be generated annually in power stations with a total installed capacity of some 3,000,000 kW (Fig. 1.).INVESTIGATIONThe aim of investigation work is firstly to collect sufficient information to allow the overall scheme to be planned and then to follow up with detailed information on eachproject. The correct balance for all aspects of this work is a matter for keen judgment, as the tunnels must be planned...

Jan 1, 1963

By H. Warren Newcomen

Assessments of the stability performance of open pit highwalls have traditionally been based on consideration of surface movement rates. Although generally accepted in industry, this approach presents challenges for establishing appropriate threshold values to allow for safe mining operations and does not address the issue of total strain. Surface movement monitoring data from a limited number of open pit mining operations in North and South America has been evaluated in terms of highwall strain, rock mass quality and inferred mechanism of instability. Threshold strain levels for key stages of highwall stability proposed from previous work have been reviewed and are generally endorsed based on evaluation of additional data. An empirical highwall strain criteria for the assessment of highwall stability performance is postulated based on the observed trends in highwall strain data from the case histories presented.

May 1, 2004