Search Documents

By G. S. Scott

In the course of the Bureau of Mines investigation relative to the causes, behavior, and control f anthracite-mine fires, attention was directed toward the correlation between the temperature of oxidation and the gaseous oxidation products in the range of temperatures between 100° and 350°C4/ These tests, made on a high-grade anthracite to determine the amount of oxygen consumed and the amounts of carbon dioxide, carbon monoxide, hydrogen and methane evolved when air was passed through samples of the anthracite at various elevated temperatures, showed that the gases evolved and their relative proportions vary with temperature, constitute a means for determining the probable temperature of the anthracite, and thus permit detection of incipient heating before a dangerous fire hazard exists. As the relationships mentioned are affected somewhat by the amount of previous oxidation of the coal, it was deemed desirable to know to what extent they might vary owing to this cause. It was also considered desirable to have a means for estimating the extent of oxidation from the gas analysis, as this would permit a more accurate estimate of probable temperature. Finally, it seemed desirable to know how much the composition of coal might vary over an extended period of oxidation, since this was previously suggested5/ as a possible means for estimating the probable maximum oxidation temperature to which a sample of coal had been subjected.

Jan 1, 1940

By John Mathews

IT is a great honor to be asked by. the Board of Directors of this Institute to deliver the Henry Marion Howe lecture. The invitation carries with it a great responsibility, which I accept with considerable hesitation and with a feeling of unworthiness to perform the duties expected of me in this hour devoted to the memory of the life, character, and work of the late Professor Howe. Many of you recall the scholarly address delivered here a year ago by Prof. Albert Sauveur, and the beautiful tribute he paid-to his friend and colleague of many years in the great work of changing the art of iron making into the science of iron. My association with Professor Howe, was of brief duration-only one year-and the relation was that of pupil to teacher. My feeling toward him in later years was always that of a humble disciple at the feet of a master. He attained his third academic degree in the year that I was born. I recall the pride I felt when, after entering the, steel industry, I received from him, from time to time, letters asking for information or, perchance, asking my opinion, and he was always most punctilious in acknowledging the source of such bits of information in his writings. It was also my good fortune to sit at the feet of another great teacher-Sir William Roberts-Austen, at the Royal School of Mines. I mention him because his name was used by Osmond in coining the word "austenite," which is the subject of this address, and Osmond's suggestion was heartily approved by Howe. These three international metallurgists were the best of friends and delighted to honor the achievements of one another. There are other reasons for mentioning Roberts-Austen at this time. It was an introduction from Howe that opened to me the door of his -laboratory as well as of his heart. It was while at Roberts-Austen's laboratory that I .worked side by side with William Campbell

Jan 4, 1925

Exploration work at the southern flank of the Mt. Coffin diapir has encountered three different types of copper ores: copper carbonate, largely malachite; secondary sulphides, mainly chalcocite replacing pyrite; and a primary arsenopyrite-tennantite-tetrahedrite-chalcopyrite association. The secondary copper ore is occasionally stratiform but mainly erratic at the contact between tillites and siltstones of the Tapley Hill formation.There have been two stages of primary mineralization.1. Arsenopyrite, tennantite, and tetrahedrite occur in siderite veins.2. Revival of the diapirism has caused fracturing and local brecciation of the rimrock and subsequently ascending solutions precipitated chalcopyrite. The chalcopyrite also partly replaced arsenopyrite, tennantite, and tetrahedrite.

Jan 1, 1972

By G. A. Wancheck

Shear tests were performed on several prepared samples of granular and powdery bulk materials to investigate the following parameters: Particle size and distribution, particle movement, moisture content, consolidation of material, bulk density, void ratio, porosity, volume change, and strain rate. A series of shear tests was performed with weight-percent-ratios of minus 0.185-inch tertiary sand and 1-1/2-by l/2-inch tertiary gravel mixtures, and weight-percent-ratios of minus 200-mesh limestone (rock dust) and minus 200-mesh bituminous float coal dust. A comparison was made for shear test results obtained with rectangular and circular shear cells utilizing the large and small direct shear testers. Specifically, the shear results obtained include the angle of internal friction or shear strength of the tested material under known consolidating pressures, and the kinematic angle of friction or coefficient of friction between the interface of a bulk material and a sample wall material. The experimental procedure, tests, and results are given for each parameter investigated.

Jan 1, 1973

By William H. Schiffbauer

The Bureau of Mines is conducting research that is aimed at making the mining industry more efficient in term of both productivity and the health and safety of the worker. As part of this research the Bureau of Mines has integrated a testbed composed of computer and related peripheral hardware to form an intelligent base for performing autonomous mining machine experiments. Although this particular application was con- figured for use on a Joy 16 CM mining machine, its generic structure facilitates its attachment to a variety of mining machine types. The multitasking multiuser computer can be set up for other applications by changing a bubble memory cartridge. The Joy 16 CM implementation includes 96 digital input-output (1-0) ports, 32 analog inputs, 8 analog outputs, 2 serial data channels, and 1 printer port. Operation of the machine can be performed either through a local terminal or remotely through a modem hookup. This report describes a testbed for autonomous mining machine experiments (TAMME)--its hardware, software, and complete system integration--so that it can be used as a foundation for other applications.

Jan 1, 1988

By C N. Whata

While there is no specific obligation on the part of any applicant to consult directly with tangata whenua (people of the land), recent cases highlight the need to engage in active consultation in order to avoid serious objections and delay, particularly where a proposal may affect the matters referred to in section 6(e) (Waahi tapu/sacred places) and 7(a) (KaitiakitangaiGuardianship) of the RMA.   The Environment Court has shown some sympathy for tangata whenua where waahi tapu and other significant matters of cultural concern are at risk because of a proposed development. There are several practical steps that can be taken to minimise the potential for serious objection including: ò knowing who to contact and how to contact them; ò demonstrating empathy for the concerns of tangata whenua; ò engaging in proactive consultation, for example meeting at a time and a place that is suitable to tangata whenua, and a preparedness to meet the costs of tangata whenua etc; ò demonstrate an awareness of tangata whenua issues; being aware of the types of mechanisms that are available to remedy, avoid etc adverse effects on matters of concern to tangata whenua.

Jan 1, 1997

By Norman O. Lotter, André R. Laplante

"The pursuit of concentrator surveying for purposes of metal accounting or process optimization has not yet connected with the well-published realm of geostatistics. The reality of lognormality in time has seldom been discussed. One publication by Krige, 1962, examined such effects for a gold concentrator in South Africa, towards an information system that would provide feedback to the mining and surveying teams on grade control of ore mined.During present studies which are designing and testing a new survey model, called statistical benchmark surveying, it was found that the distributions of feed, concentrate and tailings bear significant residual signs of the parent lognormality in space. The multiple hosting of paymetals in different mineral species complicates the understanding of these distributions. These features have to be recognized and treated in order to perform appropriate quality control on the diagnostic sampling performed in the pursuit of statistical benchmark surveying.It is shown in this paper that the above two features can actually be used to advantage in the diagnosis of continuous periods of operations data ahead of such surveying, including the estimation of recoverable paymetals in flotation tailings from a graphical method.INTRODUCTIONAssessment of Concentrator PerformanceMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes, which have traditionally been used to treat ore that has been mined. This is because these processes liberate, then separate, the valuable minerals, which contain paymetals, from host gangue. This is often done by a combination of crushing and grinding processes, or autogenous grinding, to liberate the paymetal minerals, followed by gravity separation and/or flotation, to separate these valuable minerals into a concentrate, or several concentrates. These concentrate(s) have a lower bulk than the parent ore from which they are derived. Further, they contain a high percentage of the valuable minerals. Accordingly, they are more economically treated in subsequent beneficiation processes than the ore from which they were produced."

Jan 1, 2005

By Forrest T. Moyer

INJURY experience and employment data are presented in this (chapter for metal and nonmetal mines, stone quarries, sand and gravel pits, iron-blast-furnace slag plants, and metallurgical plants (including ore-dressing and nonferrous reduction plants and refineries) in the United States. Employment and injury experience data for all mineral industries are given in volume III. The 1963 figures are preliminary and are subject to revision. METAL MINES Preliminary estimates for the metal-mining industry of a combined fatal and nonfatal injury-frequency rate of 32.34 per million man-hours in 1963 indicate only a slight change from the rate of 32.00 in 1962. Metal operations had 41 fatal and 3,110 nonfatal injuries during 1963.

Jan 1, 1964

By Ajit Godbole, Ping Chang, Ramakrishna Morla, Purushotham Tukkaraja, Shivakumar Karekal

This paper presents the results of a study on the optimum auxiliary fan location to control air recirculation in dead-end workings where diesel-powered vehicles operate. Investigations were conducted with various secondary fan locations from the dead-end crosscut and with the intake air quantities varied using different auxiliary fans to control air recirculation and diesel particulate matter (DPM).

Jul 1, 2023

By PEILIN LAN, LEONARD HILL, SIMON TIMBILLAH, BERNARD FOSU, CESAR SOSA-BLANCO

The use of sodium hydrosulfide (NaHS) in most of the operations in byproduct molybdenum flotation comes with safety concerns and, in some instances, a high reagent cost. Engineered solutions at the various operations where NaHS is used have immensely reduced the possibility of hydrogen sulfide (H2S) gas evolution. However, the threat of exposure remains, and this, coupled with the high dosages of NaHS consumed, supports the continued search for alternative depressants. This paper focuses on efforts to study the applicability of disodium carboxymethyl trithiocarbonate (DCMT), an organic depressant, as an alternative to NaHS. Bench-scale rougher flotation results for samples from the Sierrita copper–molybdenum (Cu–Mo) plant showed the best DCMT performance at 8 kg/t of DCMT, pH 10.5, 30 min of shear conditioning and 10 min of flotation conditioning. The Aminpro plant model simulation confirmed that 4 to 8 kg/t DCMT under certain shearing and conditioning times achieved superior or equivalent Mo–Cu separation efficiencies when compared\ to NaHS.

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Louis J. Cabri

"Mineralogical evaluation of ores containing platinum-group elements (PGE) is fraught with difficulties because of the low grades (often 1-3 g/t PGE), dispersal of PGE (usually as finegrained platinum-group minerals [PGM]), as well as occurring in solid solution in some base metal sulphides (BMS) such as pentlandite and pyrrhotite. Mineral processors not only need to know how the PGE are distributed, that is, their mineralogical distribution, but the grain sizes of the PGM, and especially the associated minerals.After obtaining a representative ground sample, common approaches include studying a large number of polished or polished thin sections, concentration of the PGM and sulphides by different gravity methods (e.g., heavy liquids, elutriation, micro-panning) and study of the produced concentrates. Unfortunately, these methods often do not produce concentrations that are sufficiently representative of a particular ore. The newly developed patented technology of hydroseparation (Rudashevsky et al., 2002) is especially effective at making concentrations of PGM over a wide range of concentrations (down to <300 ppb Pt+Pd+Au) and size fractions, including <45µm (down to a few micrometres in size), a size range not possible by other techniques. This water-based environmentally friendly laboratory technique provides a large amount of data from samples, which can range from 5 to 1000g, giving confidence to extrapolation of results to bench-scale and larger test work, especially when combined with quantitative image analysis to determine modal percent of major minerals and mineral liberation data, needed to predict the minimum (K80) and optimum (K40) grinds. INTRODUCTIONThe invention of the electron microprobe in the early 1960’s and scanning electron microscopes (SEM) with energy dispersive spectrometers (EDS) in the 1970’s presented mineralogists with powerful tools permitting them to obtain chemical and surface area data on minute amounts of minerals in situ, in a non-destructive manner. An area of process mineralogy that has very much benefited from this new technology was the characterization and understanding of PGM species, resulting in rapid growth of newly characterized species (Figure 1). Recognition of the first PGM may be ascribed to the Spanish explorer Ulloa in 1748, who described native platinum from South America. The second PGM (laurite, RuS2) was only recognised in 1866 by Wöhler in placer samples from Borneo (now Kalimantan) and the third (sperrylite, PtAs2) by Wells in 1889 from the Sudbury Ni-Cu sulphide deposits. The discovery of the important Pt-Pd deposits in the Bushveld Igneous Complex led to the characterization of the important Pt-Pd sulphides (cooperite, PtS2 in 1928 and braggite, (Pt,Pd)S2 in 1932). By the early 1960’s, only about 20 PGM were recognised, and many later proved to be poorly or incompletely characterized. Thus, the introduction of electron probe microanalysis (EPMA) led to a 50% increase of known PGM, as shown in a 1972 review on PGM (Cabri, 1972). At the time of the next review in 1981 (Cabri, 1981) the number of known PGM had grown to 75 and as of 2002, it had increased to 109 (Cabri, 2002). However, it is the author’s experience that less than about 25 PGM may be considered to be “common”, i.e., found in many different deposit types, as shown in Table 1, but usually only some of these occur in any one particular deposit."

Jan 1, 2004

By C. Dirscherl, M. Combes

"Declining ore grade, leading to increased material transport and plant throughput requirements, is one of the major challenges in the current mining environment. This is accompanied by rising energy and labor costs, decreasing plant productivity and the requirement for highest plant availability. Siemens’ answer is the latest gearless drive technology for grinding and conveying. Gearless drive solutions are surpassing the mechanical limits of conventional drive systems serving to utilize the principle of economies of scale. By elimination of various components of the drive train the maintenance activities and spare parts inventories are reduced. The advantages are culminating in the incomparable availability of the Siemens’ gearless drive technology of 99.46 to 99.71% - as confirmed by real operational data from the Antapaccay mine in Peru. It was the first plant worldwide to use gearless drives for both applications.INTRODUCTION – THE GEARLESS PRINCIPLE The principle idea behind a gearless drive system is to reduce the number of components and diversity of parts. Especially those components that are at the edge of current manufacturing or power limits are eliminated. The used equipment provides the possibility to scale up and increase the power transmitted to the driven machine. This finally results in a possible increase of throughput respectively transported or processed material. In order to apply this principle of simplification we will take a look at the components of a conventional drive system consisting of: - Driven equipment (mill, conveyor, slurry pump) - Components altering the rated speed (gearboxes, girth gear / pinion) - The electric motor - Starting devices for the motor (VSD, CCV, LRS, clutch), which are necessary because a direct across-the-line start of high power motors with load would result in a significant drop in the line supply voltage - Alternatively a variable speed drive (VSD) or cycloconverter (CCV) to utilize the possibility of speed variation during operation - The electrical supply system (cables, switchgear, transformers, protection equipment)"

Jan 1, 2014

Radioisotope x-ray and neutron techniques of analysis can be used for the determination of a wide range of elements in minerals. The most important applications of these techniques to the mineral industry are for onstream analysis of slurries and solids, and for geological assay.The radioisotope x-ray techniques are the more developed ones and two installations for on-stream analysis are in routine use in mineral processing plants in Australia. Neutron techniques are being developed, and should prove valuable for geological assay of large numbers of mineral samples, for borehole logging, and for specific on-stream analysis when the cost of the equipment is warranted.

Jan 1, 1970

By S. S. Makgato

In this study, coke oven tar additions over a range of 0?8 wt.% were evaluated as a possible substitute for imported coal fractions. The coke oven tar used was collected from tar decanters in the byproducts section of the coking plant. The moisture content in the tar varied depending on the residence time and water carryover from the coke oven tar separators to the storage tanks. Moisture contents of 1 wt.%, 3 wt.%, and 6 wt.% were investigated in order to evaluate the effect on coal blend, carbonization, and coke properties. At 6 wt.% moisture content with 6 wt.% coke oven tar, although the coke quality improved the yield showed a 4% decrease. On the other hand, 1 wt.% moisture content with coke oven tar of 6 wt.%, increased the yield by 1% and the coke quality improved. However, the latter process was characterized by an excessive increase in wall pressure and pushing energy, both of which are detrimental to the oven walls. The optimum moisture content in coke oven tar was found to be 3 wt.% with a coke oven tar addition of 6 wt.% in the coal blend. With these conditions, the coke properties improved and wall pressure and pushing energy were acceptable. However, a decrease in coke yield of up to 2% was observed. Despite this, coke oven tar addition is considered to be a viable option based upon economic factors of a reduction in the quantity and cost of imported coking coals that is required to achieve the same optimum final coke product. Keywords coal substitution, coke oven tar, tar moisture, coal blend, coke, coke quality.

Nov 1, 2013

By William S. Heckman

a. When to use: high surcharges, vertical capacity required, limit noise and eliminate vibrations, low headroom, eliminate vibration induced settlements. b. Advantages: eliminates impact noise and vibrations, high section modulus if required, vertical load bearing capacity; corrosion resistant, easy to apply facing for use as a permanent wall, adapts to complex wall layouts, would allow top- down construction, very high uplift resistance. c. Disadvantages: spoil disposal, not water tight, cannot penetrate rock and most obstructions, soil can erode between the piles if surface water and ground water are not controlled, hard to install reinforcing beams over 409 long; subject to high negative skin friction loads, high grout takes in rubble and organic soils. e. Relative cost to other systems: 30% to 50% more expensive than driven soldier piles and lagging except when surcharge loads are involved, or the pile cannot be driven due to noise and vibrations. About the same cost as a sheet pile system. Very competitive if high vertical load must be supported by the wall.

Jan 1, 1997

By Elbridge W. Gresseth

Rock deformational structures in a deep mine were analyzed by petrofabric techniques to learn (1) the relative magnitude and direction of the principal stresses involved in tectonic deformations prior to mining, (2) the preferred orientation of rock planar discontinuities which define rock anistropy prior to mining, and (3) the relationship of mining-induced rock failure to inherent rock stresses and inherent rock anisotropy. Rock fabric elements used for petrofabric analysis consisted of bedding planes, faults, joints, fractures, foliation, sericite plane (001), quartz axis [0001], quartz deformation lamellae, and microfractures. Structures and structural symmetries from different areas within the mine and from different scales of observation were compared to learn the nature of rock anisotropy and the orientation of the principal stresses defined by rock deformations. Analysis of such fabric as regional and macroscopic faults, b-c joints, quartz [0001], sericite (001), and microfractures, indicate that during the epochs of tectonic deformation, the maximum and minimum principal stresses were horizontally oriented and acted along northwest and northeast axes, respectively. This condition of regional stress appears to have continued during folding and the associated period of faulting. The most recent tectonic deformation represents a rotation of the minimum principal stresses into a vertical position, as shown by the development of a tensile joint system, quartz deformation lamellae, and microfractures. Good interscale correlation and statistical homogeneity of tectonic fabric indicate a stress field homogeneity in this area during tectonic deformation. Rock physical anisotropy is genetically associated with tectonic fabric and consists of preferentially oriented planar discontinuities intersecting along a nearly vertical axis. The mining-induced deformations were correlated with the inherent rock anisotropy which either directly controls or greatly affects their development. This phase of rock deformation shows a greater degree of stress field heterogeneity than was the case with tectonic deformations This is explained as a result of nonconfinement afforded by underground openings and the increase in ground stresses due to mining activity"

Jan 1, 1968

By E Ah Mu and C R Lilley, A D. Campbell

Cave propagation is a complex process due to interacting variables such as mine geometry, rock mass heterogeneity and complex structural networks and stress fields. The Ernest Henry sublevel cave (SLC) is directly below an open pit, which provided an opportunity to observe and measure rock mass failure as the cave initiated and propagated through the pit wall. This paper describes interaction between the open pit and SLC as well as rock mass failure mechanisms observed from the start of the SLC to surface breakthrough.Cave propagation and slope failure mechanisms were found to be governed by intermediate structures, while the cave shape was largely controlled by cave-scale faults. The open pit, production-level geometry and production draw strategy were also important factors for cave and subsidence growth. Cave propagation was episodic and asymmetric in shape due to the orientation and relative position of geological structures, combined with the effects of the increasing SLC geometry and drawdown from the underlying production levels. The precursors and failure mechanism of a 2.5 Mt wall collapse are also reviewed in detail.Cave growth was simulated using a 3D, non-linear, discontinuum finite element model coupled with Newtonian Cellular Automata. Model results are compared to field observations and monitoring data to determine the accuracy of forecasts and compared models versus actual rock mass response during cave propagation.CITATION:Campbell, A D, Ah Mu, E and Lilley, C R, 2016. Cave propagation and open pit interaction at the Ernest Henry Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The number of railroad coal cars (open top hoppers), dominated rail car orders and deliveries in 1975 according to announcements made February 11, by the Association of American Railroads and the American Railway Car Institute. Acting to keep ahead of increased coal production, the railroads installed 21,748 new coal cars in 1975, the most since 1957. The 1975 installation resulted in a net increase of 6,560 coal cars and an overall gain of 4.5 percent in the total capacity of the hopper car fleet. With most of the new coal cars going into unit train service --where car utilization is greatest --the railroads actual coal-carrying capacity was increased far more than 4.5 percent. The AAR estimated that unit train operations now move 50 percent of all rail-hauled coal compared to only 42 percent 2 years ago. COBALT - The Societe Miniere de Tenke Fungurume (SMTF) copper-cobalt project in Zaire reportedly was suspended in January for an indefenite length of time. According to officials, the deferment resulted from a number of adverse factors, one of which was exceptional increases in capital costs. The project was scheduled for completion in early 1978, with an eventual production of 14.3 million pounds of cobalt per year. Reserves of cobalt were reported to be 505 million pounds. SMTF is a consortium and includes American, British, French, Japanese, and Zairian interests.

Jan 1, 1976