Search Documents

By John C. Holtz

Interest in the possibility of using Diesel6/ engines for haulage power in mining and tunneling is increasing in the United States, owning largely to the reported successful use of Diesel locomotives in European coal mines and to the comparatively recent development of automotive Diesel engines in this country. The extent of this interest has been evidenced to the Bureau of Mines by numerous requests for information as to the factors that must be considered if Diesel engines are to be used safely underground.

Jan 1, 1940

Up to 19 chemical parameters were studied in flotation pulps in six Australian lead-zinc concentrators with the aim of obtaining a better understanding of the nature of, and changes in, the chemical environment. This paperdiscusses collector residuals, metal concentrations in solution, and other parameters.Collectors used in the plants studied were various xanthates, Z-200, and Aerofloats. Xanthate residuals varied in different ways in most plants. However the general trend was for residuals to be at the O· 5-2 p.p.m. level in lead flotation and O· 5 p.p.m. or less in zinc flotation.Aerofloat residuals were also variable but in the plant concerned were at a much higher level (8-10 p.p.m.) than xanthate residuals. Z-200 residuals were in the 10-20 p.p.m. range and it was found that the Z-200 added to zinc flotation was reporting in dam return water and entering lead flotation.Copper concentrations in solution were negligibly low in those plants where cyanide was not used. When cyanide was used, copper was at the 5-20 p.p.m. level and appeared to be present as Cu(CN)-2. However the hiocyanatepresent may be important. Xanthate was also present in these solutions.Zinc concentrations ranged from 0·1 to 800 p.p.m. in different plants. The general trend was for the zinc level to be highest in the grinding circuit and to drop during flotation. However there was always an increase in zinc concentration when copper sulphate was added, even tho.ugh this incre.ase was not permanent, and the increase was greater with higher copper sulphate additions.The manganese concentration also increased appreciably during copper-activation of marmatite. In some plants lead concentrations increased from 0·1 to 1 p.p.m. during activation of marmatite.Calcium concentrations (20-1200 p.p.m.) and magnesium concentrations (10-600 p.p.m.) tended to be fairly stable in each circuit.

Jan 1, 1970

By Lawrie D. C

Finely ground beryl was decomposed by mixing with ground limestone and soda ash and heating at 900°C for 4-6 hr. The sintered mater:al was then crushed and leached by boiling under reflux with 5N sulphuric acid for up to 4 hr. The liquor containing Be, AI, Fe and other elements as sulphates, was separated from the residue which consisted mainly of silica and gypsum, either by filtration or bydecantation washing.The clarified leach liquor was first treated to remove Fe+++ by contacting with a primary amine-kerosene solution in 2 countercurrent stages. The iron free liquor was then passed to a 4-stage counter-current extraction unit where it was contacted with O·5M di- (2 ethyl hexyl) phosphoric acid (EHPA) in kerosene. Under the operating conditions, 99 per cent of the Be and 7 per cent of the Al was extracted.The Be and Al were stripped from the organic phase by sodium hydroxide solution of suitable concentration to form soluble "beryllate" and "aluminate" respectively. Most of the Be was subsequently precipitatedas Be(OH)2 by heating the alkaline solution to 90°C, the Al remaining in solution. After filtration and washing, the Be(OH)2 could be ignited directly to BeO at about 1000°C or used as a feed to further purification stages if required.A small counter-current extraction unit was operated continuously using liquor derived from the sintering and leaching stages. Dataobtained in batch laboratory tests were confirmed. A product obtained by ignition of the washed "beryllate" precipitate contained more than 99 per cent BeO.INTRODUCTIONIn 1958 an investigation was commenced into the recovery of beryllium oxide from beryl, as part of a programme to utilize mineral resources of South Australia. A survey of the literature indicated that little work had been done on direct solvent extraction of beryllium from aqueous liquors, so it was decided to apply the experience gained in this field in uranium processing to the current problem.Preliminary extraction tests on solutions of beryllium...

Jan 1, 1965

By L. A. Cornish, S. N. Prins, R. Süss

The work is being done using the Thermo-CalcTM software, and the database is being built up by obtaining good thermodynamic descriptions of all of the possible phases in the system. The database supplied did not cover all of the phases, and these had to be gleaned from literature, or modelled using experimental data. Similarly, not all of the experimental data were known, and where there were gaps or inconsistencies, experiments had to be undertaken. A preliminary version of the database was constructed from assessed thermodynamic data-sets for the binary systems only. The binary descriptions were combined allowing extrapolation into the ternary systems, and experimental phase equilibrium data were compared with calculated results. Very good agreement was obtained for the Pt-Al-Ru and Pt-Cr-Ru systems, which was encouraging and confirmed that the higher-order systems could be calculated from the binary systems with confidence. Since some of the phase models in databases were different, these phases had to be remodelled. However, more work is ongoing for information concerning the ternary phases present in the Al-Cr-Ru, Pt-Al-Ru (two ternary compounds in each) and Pt-Al-Cr (possibly more than three ternary compounds) systems. At later stage of the work, problems with the thermodynamic descriptions of the Cr-Ru and Pt-Cr binary systems were found. A programme of experimental work to overcome these has been devised, and is being undertaken. Keywords: Pt-based alloys, phase diagram calculations.

Jan 1, 2006

By A P. Tinnelly

This paper explores the structural/physical and policy based issues that have lead to the apparent resource conflict between Forestry and Mining on the West Coast. Both industries are important to the West Coast and bear many similarities, particularly at the corporate end of the mining scale. However there are very distinct structural differences which set the scene for friction at the boundaries. Examples of how mining impacts upon forestry illustrate where some of the friction arises and provides some insight as to where some solutions are or may be found.

Jan 1, 1996

By G. R. Hopkins

"Refiners are generally considered solely as fuel producers, but actually they also comprise a group one of the largest consumers of fuel. For example, during the year 1929 the refineries-burned 51,544,000 barrels of oil as fuel, or the equivalent of over 5 per cent of the crude oil processed in that year. In addition enough other fuels - coal, natural gas, refinery or still gas, and petroleum coke - were utilized to raise the total fuel consumption based on B. t. u. equivalent to more than 10 per cent of the heat value in the total crude oil run to stills. Refineries utilize fuel chiefly as the heat-forming element distillation, but also under-boilers in the formation of steam used in refining, for the heating of buildings, and in the generation of electricity.In the early days of refining, the problem of fuel utilization and fuel economy was of scant importance to the refiners. Margins of profit were comparatively high and the major portion of the operatros1 attention was directed toward increasing their throughput. However, the keen competition that has prevailed in the refining industry over the past five years or more has taught the refiners that their expenses, one of the largest items of which is the cost of fuel, must be curtailed. Thus in 1925 the refiners used an average of 829,000 B. t. u. to refine a barrel of crude oil, wheras by 1929 this average had been reduced to 639,000 B. t. u., a decline of 23 per cent (see fig. 1)Since 1925 oil has ranked first as a refinery fuel (see fig. 2). The use of natural gas increased during 1926 and 1927 but declined in 1928 and 1929. On the other hand, the use of refinery gas has grown rapidly in importance. Coal has shown a steady decline in use at refineries since 1925. Petroleum coke has never supplied more than a very small fraction of the total fuel requirements, although there has been a steady increase in its use."

Sep 1, 1930

By Lavers G

Factors governing the dissolution of nickel and iron in pentlandite and pyrrhotite concentrates from Mt. Windarra were studied for aqueous solutions at normal temperatures and pressures. The effects of dissolved dioxygen, carbon dioxide, hydrogen ions, and chloride ions are described. The direct reaction of aerated water wiili pyrrhotite is much faster than with pentlandite, and reaction rates are proportional to the dissolved dioxygen concentration. In both cases divalent metal sulphates are produced initially. The subsequent oxidation of iron(II) to iron(III) and its oxolation produces acid solutions which rapidly attack both minerals. The presence of carbon dioxide or chloride ion has little effect on these rates.

Jan 1, 1976

By J. G. Donaldson

Optimum conditions are given for chloridizing pyrite, marcasite, chalcopyrite, arsenopyrite, stibnite, and covellite with chlorine gas. The formation of metal chlorides is affected by the time and temperature of chloridizing, and by particle size of the sample. Chloridizing data also are given for chemically precipitated antimony (III) sulfide and copper (II) sulfide.

Jan 1, 1962

By Clark F. Grain

These investigations were undertaken as part of the Bureau of Mines program for the development and evaluation of high temperature nonmetallic materials. This report consists of thermal expansion and phase inversion measurements by high-temperature X-ray diffractometry on the principal oxides of beryllium (BeO), calcium (CaO), titanium (TiO2 ), zirconium (ZrO2 ), hafnium (HfO2), and thorium (ThO2); all were high-purity commercially available oxides. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures. Expansion was determined parallel to each major crystallographic axis for the anisotropic oxides: BeO, TOi2, ZrC2, and HfO2. Combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C. and approximately 2 percent at 1,000° C. No hysteresis in the expansion curves was noted between heating and cooling cycles. The Bureau's values were compared with published expansion measurements obtained by X-ray diffraction, dilatometric, interferometric, and telemicroscopic techniques. For anisotropic oxides, average linear expansion values were calculated from the volume expansion.

Jan 1, 1962

By Dennis Molvik, Omar Fulton, Chris D. Breeds, Don Gonzales

This paper presents and describes the South Interceptor Parallel Phase III Contract C93012C, which involved construction of a nominal 2.7 m (9-ft) finished diameter sewer conveyance using both pipe jacking and conventional tunneling methods. Earth Pressure Balance (EPB) excavation was required to minimize the potential for settlement beneath a main rail line, overpass, sensitive wetland, areas of contaminated soils, and nearby structures. Ground conditions predicted in the Geotechnical Baseline Report included low plasticity, clayey silt (40 to 10%) and silty sand (60–90%) with pieces of wood such as logs, stumps, branches and other tree fragments. Soil cover ranged from 2.7 m (9-ft) to 5.4 m (18-ft) over the tunnel crown with a groundwater table between 1.5 m (5-ft) and 3.7 m (12-ft) deep.

Jan 1, 2003

By J. A. Berger, R. J. Towner

The pjPocesses of polygonization and subgrain growth were followed in slightly stretched 99.99 pct A1 single crystals heated for cumulative times at 400°, 500°, and 600°C. Changes in sub-grain size and boundary angle were determined from measurements on X-ray micrographs. CAHN1, 2 studied polygonization in stretched and heated aluminum single crystals of 99.99 pct A1 using various techniques, including etch pits, Laue patterns, and a slight restretching of heated specimens to reveal small changes in lattice orientation by the direction of new slip lines. He found that kink bands, which had well-defined boundaries lying in a plane perpendicular to the slip direction (at least in the early stages of deformation), formed during stretching. Also, he noted that bending occurred about the <211> axis lying in the (111) slip plane perpendicular to the <110> slip direction. His studies of polygonization were largely confined to the kink bands rather than to the weakly bent matrix regions between bands. The minimum temperature required to bring about polygonization was established at about 450 "C. Guinier and Tenevin used a focusing Laue X-ray diffraction technique to study polygonization in aluminum single-crystal specimens of 99.99 pct purity. Stretching the crystals 5 pct in tension caused a widening of the focused Laue spots. After heating for 4 hr at 450°C, their method revealed no change in the specimen. Above 450°C polygonization was detected and further annealing near 600°C led to subgrain growth. They concluded that the orientation of the crystal relative to the axis of deformation had no marked effect on polygonization. Gay and Honey-combe4 using an X-ray microbeam technique found that polygonization did not occur in a stretched aluminum crystal heated at 250oC, although some decrease in the yield strength occurred. When the temperature was raised to 475oC, the asterism became broken up as a result of polygonization. Honeycombe5 noted that reflections on X-ray mi-

Jan 1, 1961

By Yves St-Amour, Vince Luongo

This paper will discuss one of the largest construction projects the City of Portland has undertaken. This phase of the Willamette River Combined Sewer Overflow (CSO)project consists of approximately 18,500 ft of tunnel in soft ground, requiring the construction of six deep shafts and jet grout ground improvement. The purpose of the project is to reduce volume of combined sewerage overflows from the drainage areas on the west side of the Willamette River. Bencor-Petrifond-Pacchiosi Joint Venture was awarded a contract to design and construct six deep circular shafts, jet grout ground improvement for three bridges and jet grout ground improvement break-in/outs for some shafts. Of the six shafts the Pumping Station Shaft was the deepest and largest, requiring a permanent ground support system with a deep jet grout ground water cut-off to 335-ft deep. The joint venture used state of the art methods and equipment to achieve its objectives and build the structures through some very difficult alluvial soils to great depths next to the Willamette River. The paper will provide a general discussion of the shaft construction and jet grout ground improvement installed for this phase of the project. It will also discuss some of the technical challenges encountered while effectively managing risk and costs, resulting in a successful project completed in a timely manner.

Jan 1, 2005

By Raymond A. Mazzoni

Over the last twenty years, roof support technology has made numerous advances since the original wedge and slotted bolts of the 1950&apos;s. By comparison, the roof supports used today are more complex and specialized than the supports used in the past, providing mines with a varied selection of supports from which to choose. As a result, when problems with supports are encountered, it is more difficult to determine whether it is the result of geological changes, poor installation practices, or malfunctioning supports. Recognizing this problem, MSHA&apos;s Roof Control Division of the Pittsburgh Safety and Health Technology Center, has undertaken the task of publishing a guide for trouble¬shooting problems encountered with roof support systems. The purpose of this guide is to provide a logical sequence to resolving the most common problems encountered with roof supports. The objective of this paper is to introduce this guide to the mining industry as well as provide insight into the evolution of the guide from its beginnings as rudimentary charts to its more comprehensive present format as a practical guide for use by the mining commu¬nity.

Jan 1, 1997

By Alan Galley

CMIC Mandate CIM Annual Meeting, Toronto, May 6, 2013 To increase mining research, innovation and commercialization efforts in order to strengthen Canada?s pre-eminent role as a global leader in mineral exploration, mining and knowledge-based services and technologies. To increase the supply of highly qualified graduates from mining and earth sciences faculties to meet the significant demand today and into the future of industry, governments and academia. The CMIC initiative is intended to develop long term research strategies that extend five or greater years. Such a research plan will underpin fundamental research and innovation and the training of HQP

May 1, 2013

By Darrell L. Beddard

The Loma Prieta earthquake occurred on October 17, 1989 at 5:04 PM, Pacific Daylight Time. It measured 7.1 in magnitude and was felt from Los Angeles north to the Oregon state line and east to western Nevada. The epicenter of the earthquake was located along the San Andreas Fault, in the Southern Santa Cruz Mountains just north of the City of Watsonville, California. It was the largest earthquake to occur in the San Francisco Bay area since the 1906 earthquake. A total of 87 aftershocks of Magnitude 3.0 or larger were recorded within 21 days after the seismic event. As a result of this earthquake thirteen State-owned and five locally-owned bridges were closed to traffic. Three of the most publicized State-owned structures closed to traffic were Struve Slough Bridge, San Francisco-Oakland Bay Bridge and Cypress Street Viaduct. Struve Slough Bridge was twin slab bridges that collapsed and were rebuilt and open to traffic three months after the earthquake. San Francisco-Oakland Bay Bridge experienced collapse of upper and lower spans at Pier 9 and was reopened to traffic one month after the earthquake. The Cypress Street Viaduct experienced collapse of 48 bents that resulted in the upper roadway falling onto the lower roadway.

Jan 1, 1995

By Jack Bedder, Nils Backeberg

"Native antimony metal is rare and antimony generally occurs together with gold, lead, copper and silver. There are more than 100 antimony minerals, although the sulfide mineral stibnite is the main economic mineral.Antimony enters the supply chain either as a result of mining (primary production) or recycling (secondary production). China has by far the largest antimony resources and is, as a result, the world’s center for antimony mine production. While China remains the leading primary producer, accounting for 69 percent (80.5 kt or 88,700 st) of the global 117.5 kt (129,000 st) in 2017, market consolidation and regulatory inspections across China leading to closures of facilities have caused a significant decrease in Chinese output from 115.8 kt (127,600 st) in 2015 (81 percent of global production).Tajikistan and Russia are the next largest producers of antimony after China, both ramping up production in recent years. Russia could significantly increase its supply of antimony if Polyus moves ahead with supplying 10-12 kt/a (11,000–13,200 stpy) of contained antimony from gold tailings. Australia and Bolivia are also significant mine producers outside China. The value of the different ores varies based on the metal content of the concentrates, with the most valuable gold-bearing ores sourced from Australia’s Costerfield Mine and the least valuable mercury-bearing ores sourced from the Anzob Mine in Tajikistan. On average, Bolivian and Russian ores trade at an intermediate value between those from Costerfield and Anzob. Nearly all of the rest-of-world production is exported to China, where the ores and concentrates are processed into antimony ingots and oxides.Antimony ingot production is not as widespread as is the case with antimony mine production, owing to the high levels of pollution that are associated with antimony smelting. It is for this reason that smelting has been largely confined to China and other Asian countries ,such as Vietnam and Myanmar, where environmental legislation has historically been less stringent. Tajikistan has become a growing producer of antimony ingot since 2014, coming from the commissioned metallurgical plant at the Anzob Mine.Antimony oxide production is undertaken on four continents with China being the biggest producer. There is also a considerable amount of oxide production in Europe (mainly Belgium and France), which relies on imported antimony metal feedstock, mostly from China.A new antimony project under construction by Strategic and Precious Metals Processing (SPMP) in Oman made progress in 2016 and 2017, and after producing first metal in April 2016 in test facilities, was set to be commissioned in the first quarter of 2018. Commissioning had been moved back to June 2018, with a potential ramp-up to 2-3 kt/a (2,200 to 3,300 stpy) of antimony metal by the end of 2018. SPMP is also reviewing producing antimony oxide as part of its flow sheet."

Jan 7, 2018

By David E. Fogelson

One model each of three different makes of portable displacement seismographs was calibrated on a shaking table capable of 5,000 pounds of force, Calibration tests were conducted in the frequency range of 5 to 200 c.p,s, and in the amplitude range of 0,002 to 0.05 inch peak-to-peak, The seismographs were tested under two mounting conditions: (1) The feet of the instrument were bolted to the shaking table, and (2) the feet were resting on emery cloth affixed to the table, The results of these tests show that, in the frequency range of 5 to 40 c.p,s, and for vibration levels less than 0.2 g, the magnification for all three instruments is constant with input level but varies slightly with frequency. For vibration levels greater than 0.4 g. and for frequencies greater than 40 c.p.s., the magnification of all three instruments shows large variations with frequency and amplitude of table motion.

Jan 1, 1962

"SUMMARYThe K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6 1/2 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,016 barrels of 43° A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive.Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949.The K.M.A. structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume c 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oilIn that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 at which pressure 1 barrel of stock,tank oil contained 525 cubic feet of gas in solution.A serious decline in reservoir pressure during the 2 years of rapid development alarmed the operators and caused them to consider a cooperative pressure-maintenance program. In the latter part of 1939, the K.M.A. Pressure Maintenance Association was organized, and the gasoline plants in the field agreed to process the wet gas and return the dry gas to leases having gas-injection wells. Approximately 27 percent of the cumulative volume of produced gas had been returned to the reservoir by August 1, 1949."

Jun 1, 1952

By Kevin W. Cargill

In September 2004, Hurricanes Frances and Ivan caused the Pigeon River in western North Carolina to flood. This flooding eroded the embankment below Interstate 40 (I-40) and sent one of the eastbound lanes, along with the roadway shoulder, into the river below the embankment. North Carolina Department of Transportation (NCDOT) needed to reopen all the lanes of I-40 as soon as possible and considered this damage to be an emergency situation. NCDOT contracted Schnabel Foundation Company to design and build a repair that would keep this important interstate open and reestablish the eastbound lane. The obstacles included limited work room, the requirement of keeping the remaining lanes of I-40 in service, and producing a final product that would be relatively maintenance free and last at least 100 years. The proposed repair had to consider that the existing interstate was founded on a rock fill that was constructed from rock blasted off the adjacent mountain side. The selected design included two, tied-back micropile walls to address these obstacles and other issues. Each of the walls were constructed of 10.75 inch diameter micropiles and corrosion-protected tieback anchors installed through the existing rock fill into competent bedrock, concrete wales, and a reinforced shotcrete facing. This successful project was completed during the coldest months of the year and within the timeframe established by the State of North Carolina. This paper will discuss the design and construction of the repair and the many challenges that had to be overcome.

Jan 1, 2006

By P J. B Fransen

Several spatially and/or temporally distinct phases of epithermal activity can be recognised in the Horohoro-Matahana Basin area of the Taupo Volcanic Zone. In the northern Matahana Basin a 140 - 350 ka age range is proposed for mineralised debris flow clasts and related (?) epithermal &nbsp;mineralisation intersected in a recent drillhole. To the east, a ca. 40 - 50 ka age range is suggested for epithermal activity in the Waikaukau alteration zone which was focused along the Guthrie Fault. Hydrothermal explosion breccias occur over 13 km within the Guthrie Graben, and are probably sourced from vents in the south. Assuming a common origin, these breccias are constrained to a 45 - 50 ka age range. Within the Horohoro hydrothermal system (around the present hot spring), older (15 - 50 ka) and younger (0 - 15 ka) features can be distinguished.

Jan 1, 1991