Search Documents

The Ediacara mineral field is classified as a Mississippi Valley type deposit with stratiform mineralization near the base of the Cambrian beds. Mineral deposition was contemporaneous with sedmentation and reerystallization, and mobilization took place after lithification of the sediments. Several mechanisms of deposition were possible.INTRODUCTIONThe Ediacara mineral field is located in the Mt. James Range approximately 300 miles north of Adelaide, about 12 miles west of Beltana railway siding and 10 miles east of Lake Torrens. It is isolated geographically from similar deposits of equivalent age and environment in the Flinders Range Province (Fig. 1). The climate may be described as semi arid with high summer temperatures and frequent dust storms. Occasional thunder storms are the main source of rain in the summer months.The exact date of discovery is unknown, but is believed to be about middle of the last century. Ulrich (1872) was the first geologist to report on the field. At that time only the southern portion of the field had been prospected (and abandoned). Although the prospects did not appear encouraging Ulrich advised prospecting of the shales and testing beneath the limestone.In 1888, Rosewarne, an Inspector of Mines, visited the Southern Workings and queried whether they were connected with some lode at deeper level or were merely bedded deposits. The first geological map with sections was drawn by H.Y.L. Brown (Brown 1892).Brown recognized three principal rock formations as dolomitic sandstone, kaolinised shales and sandstone, and quartzites and sandstone in descending order. These three basic units are still recognized. He recognized also the stratiform nature of the mineralization in the shales as a...

Jan 1, 1963

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor. At a large open cut copper operation, challenging geological structure resulted in slabby and blocky fragmentation in the stemming region, resulting in poor crusher throughput due to bridging. To overcome the poor fragmentation in the top of the bench, longer than conventional subdrill was used to precondition the top third of the bench. The technique significantly improved the run of mine fragmentation and resulted in feed to the in-pit crushers that is more consistent, which produced less crusher downtime due to bridging. A new method of quantifying the energy in a blast has been created. Termed the linear powder factor, or energy factor, the calculation considers the energy contributed by the subdrill of the upper bench and its impact on the energy in the lower bench. The technique enables blast designs to be optimised to deliver finer fragmentation and more consistent blast outcomes. To support the layer of preconditioned rock at the top of the bench, an innovative new device was developed. The device is inserted into the drill collar immediately after drilling and remains in position throughout the subsequent steps of hole depth measurement, priming, loading and removed prior to stemming. The device not only supports the broken rock at the top of the bench, but also minimises the amount of drill cuttings that fall back into the hole. Furthermore, the device helps protect the hole from damage by external factors such as weather events, drill tracks, vehicle tyres and movement around the collar during measurement and loading of the blast hole.

By A. B. Cecala

A few years ago, the National Institute for Occupational Safety and Health and Unimin Corporation developed a clothes cleaning system that is able to quickly, effectively, and safely remove dust from a worker?s clothing without dust exposure to the worker, the work environment, or co-workers during the cleaning process. To perform the process, a worker enters a cleaning booth and activates an air spray manifold which blows the dust from the worker?s clothing. Since the cleaning booth is under negative pressure, all the dust and product removed are contained. In the original design, this dust-laden air was exhausted to a dust collector system. However, since most operations do not have excess dust collector capacity, it was decided to determine an alternative method to provide for a stand-alone cleaning system. This was achieved by ducting the exhaust outside the plant and into the atmosphere. This technique was recently tested and shown to be a viable method to provide for a stand-alone clothes cleaning system.

Jan 1, 2009

The ore milled from the Lead Lode of The Zinc Corporation leases consists of a fairly granular mixture of galena, marmatite, chalcopyrite, tetrahedrite, pyrrhotite, pyrite, and lollingite with a gangue association of calcite, quartz, bustamite, rhodonite, mangan-hedenbergite, garnet, fluorite, mangal1o-calcite and apatite. The silver content of the ore occurs in three minerals-tetrahedrite, dyscrasite, and pyrargyrite, the last two mentioned occurring in microscopic association only. Other metallic and gangue minerals are also present in this complex mineralogical association, but do not influence the milling operations. Fortunately, the silver minerals favour the galena and chalcopyrite as their host minerals, thus facilitating the recovery of both copper and silver in the lead concentrate. The ore from the Lead Lode assays from 14-18% lead; 3·0-4·5 oz. silver per ton, and 9·5-12·0% zinc.A parallel lode, known as the Zinc Lode, is well developed in The Zinc Corporation leases. This lode assays from 6-8% lead, 1·5 oz. silver per ton, 18-25% zinc with a siliceous gangue. The common Lead Lode gangue minerals-ealcite, rhodonite, bustamite-are very rare in present underground exposures. No metallurgical work was done on this ore during the pilot plant operations.The aim in the milling process is to produce: 1. A lead concentrate with the maximum economic recovery of lead, silver, gold, copper and antimony, and minimum zinc content.2. A zinc conc,entrate with the maximum economic recovery of zinc, cadmium, and cobalt, and minimum iron, arsenic and fluorine content.3. A waste residue containing sufficient granular material to be utilized as underground fill.In considering the economics of the milling practice the above three requirements plus consideration of the tariffs submitted by the purchasers of concentrates were the deciding factors in the evolution of the present milling practice.Towards the end of 1924 The Zinc Corporation Limited added to and adapted the old zinc tailings plant for the treatment of 5,000 tons of crude ore per week. This plant, which operated until January, 1936, was in general principles similar to the standard Broken Hill methods of ore concentration, whereby the galena was recovered by the gravity concentration methods of Hgging and tabling with selective flotation concentration of the residual galena and marmatite. One important difference from other Broken Hill plants was that the primary grinding of the jig tailing was performed with flint-loaded mills operating in closed circuit with revolving screens. Two primary grinding sections were installed, each...

Jan 1, 1941

By Neil White

South Africa (SA), a country in which all three commercially important asbestos minerals have been mined and milled, has retained proven cases of mesothelioma linked with environmental exposure to asbestos. This study illustrates the importance of fiber type in the occurrence of environmental mesothelioma. Four studies have reviewed the source of occupational or environmental asbestos exposure in 504 histologically proven cases of mesothelioma in South Africa. One hundred and eighteen cases (23%) were thought to be related to environmental exposure to asbestos. In the vast majority of these cases, exposure was linked to crocidolite mining activities in the Northern Cape Province. Two cases were thought to have occurred in relation to amosite and Transvaal crocidolite exposure in the Limpopo Province. In the balance of cases there was some uncertainty. No cases were reported with exposure to South African chrysotile. Consequently, in the vast majority of cases of mesothelioma, environmental exposure to asbestos occurred in the Northern Cape Province, in proximity to mines, mills and dumps where crocidolite was processed. Crocidolite appears to be far more mesotheliomagenic than amosite, and chrysotile has not been implicated in the disease. This is true for both occupationally and environmentally exposed individuals. ©2007 Elsevier Inc. All rights reserved. Keywords: Crocidolite; Mesothelioma; Chrysotile; Amosite; South Africa

Jan 1, 2007

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By D. J. Cheung, V. N. Kazakidis

ABSTRACT Seismicity and rockburst problems in hard-rock mines negatively impact safety and profitability. The authors propose a design risk methodology as a relative risk assessment for underground excavations vulnerable to rockburst damage. It considers rock mass conditions relating to mininginduced stress, geological structure, rock mass properties, and mining influence. Application of the methodology to rockburst cases involving seismically active fault zones at the Craig mine in Sudbury, Ontario, Canada, demonstrates that design changes can reduce exposure and economic risks. Mines with high geotechnical risk can use the design risk methodology to evaluate design alternatives as a risk management strategy.

Jan 1, 2014

By Eleanor Abshire

[THE INCREASING use of hafnium as a vital component in atomic power reactors has brought this metal into recent prominence. A literature survey was made and this bibliography was compiled to provide research and production groups with a ready source of reference to this important metal anti its compounds. This service is rendered by the Zirconium Information Center, which is sponsored by the Department of the Navy, Bureau of Ships, and the F .S. Department of the Interior, Bureau of Mines, tit the Bureau's Northwest Electrodevelopment Experiment Station, Albany, Oreg. The following reference sources have been reviewed for this compilation : Chemical Abstracts; Industrial Arts Index; Crerar Metals Abstracts; Nuclear Sciences Abstracts; Bureau of Mine; Information Cicular 7771, Bibliography of Zirconium; anal Bureau of Mint' Information Circular 7830, Bibliography of Zirconium, suppllement to Information Circular 7771.]

Jan 1, 1960

By W. D. Johnston, T. P. Thayer

THE minerals that collectively are known as chromite form an isomorphous series of the general formula (Mg,Fe) 0. (Cr,Al,Fe) 203. So wide is the range in chemical composition in this group that chrome ore consisting entirely of the mineral chromite may range from less than 30 pct to more than 60 pct Cr203. The most comprehensive published data on the chemical com- position of chromite are by Stevens,62 who made complete analyses of 52 samples of chromite concentrate from many localities in North, Cen- [ ] tral, and South America. These samples were mechanically purified to remove associated silicates and might be regarded as the cleanest chromite that could be obtained by any mechanical milling process. Fig 1 shows the predominant zone of isomorphism, within the triangular prism of composition defined by the mineralogical end members of the series, wherein his analyzed samples fell.

Jan 1, 1949

By A. D. Pelton

The evolution of thermodynamic models of molten salts and slags, starting with Temkin in 1948, has culminated in today?s sublattice models. These modern models have permitted the development of large thermodynamic databases of model parameters, which can be used to calculate and predict accurately the properties of multicomponent solutions. The model parameters are mainly obtained by the critical evaluation and optimization of available thermodynamic and phase equilibrium data for binary and ternary subsystems. The models are then used to estimate the properties of multi component slags and salts from these assessed binary and ternary parameters. When used in conjunction with thermodynamic databases for solids and solid solutions (salts, oxides, sulphides, metals, etc.), other liquid solutions (such as liquid metals),and gases, these databases permit the calculation of complex multiphase equilibria in multicomponent systems, with applications in a wide variety of industries. These calculations can be performed with general commercial software for Gibbs energy minimization, which can also be incorporated into process simulation software packages. Keywords: slags, salts, solution models, thermodynamics, phase diagrams, oxide systems, molten salts

Jan 1, 2004

By Keith A. Heasley

In the past, numerous displacement-discontinuity (DD) models of stratified rock masses have been proposed using a homogeneous isotropic elastic overburden. In this paper, it is postulated that a laminated overburden model might be more accurate for describing the displacements and stress in these stratified deposits. In order to investigate the utility of using a laminated overburden in a DD model, the fundamental mathematical basis of the laminated model is presented and graphically compared with the fundamental behavior of homogeneous isotropic elastic overburden and with field data. Specifically, the stresses and displacements surrounding an idealized longwall panel as determined from the laminated overburden model are presented and compared with results from the homogeneous isotropic overburden and with measured abutment stress data. Also, the remote displacements and surface subsidence as calculated by the laminated overburden model are compared with homogeneous isotropic calculations and with measured subsidence data. The results of this investigation show that the laminated overburden is more supple, apt to propagate displacements and stress further, and better able to fit observed data than the classic homogeneous isotropic overburden. Ultimately, it is suggested that the laminated model has the potential to increase the accuracy of displacement and stress calculations for a variety of mining situations.

Jan 1, 1996

By W. Roy Dunbar

"The Porcupine area is in northern Ontario at the intersection of N. Lat. 48° 30' and 81° W. Long. It is 125 miles due north of the Sudbury nickel range. Practically all the mineral production of this area has come from the townships of Tisdale, Deloro, Whitney, and Ogden, in order of importance. The accompanying map of the Porcupine area and its extensions to the east and west (Fig. 4) has been included to show what I consider to be an essential objective of this paper, a perspective for exploration.The discovery of gold ore in the Porcupine area at such an early date resulted from the extension of the Temiskaming and Northern Ontario railway and exploratory survey lines north into unexplored territory, for the early history of Porcupine is inextricably tied to the exploration along Niven's survey lines and the extension of the railway north from Cobalt to Nellie Lake. The following are the more significant events leading to the discovery of gold in Porcupine.1896-E. M. Burwash, employed by the Ontario Bureau of Mines, examined the country along Niven's base line and noted quartz veins that carried traces of gold. He was attached to Niven's survey party.1899-The late W. A. Parks reported on the geology of the portage route from Mattagami river to Night Hawk lake, for the Ontario Bureau of Mines. He noted the occurrence of gold in quartz veins and reported “I regard the region south of the trail to Porcupine lake as giving promise to the prospector"". He also was attached to Niven's survey party.1901-Charles Camsell, while prospecting for the Algoma Central railway, did some work on a vein occurrence carrying low gold on ground now known to be part of the Hollinger mine (3).1907- Extension of the Temiskaming and Northern Ontario railway to Nellie Lake.1909- Bannerman followed up Indian story about occurrence of coal, and found iron formation. He remained to prospect and found the gold-bearing vein of the Scottish Ontario property."

Jan 1, 1954

By D. Chetty

Process mineralogy forms an integral part of geometallurgy, with ore body characterisation being but one piece of the puzzle in optimising value derived from ore. This value is not only financial, but importantly speaks to sustainability from environmental and social standpoints. The reactive approach of traditional process mineralogy is increasingly being replaced by predictive methods in the geometallurgical sphere, for which mineralogical information must be timeously acquired on judiciously selected sample sets to understand ore variability and its impact on orebody processing. Such processes are not only metallurgical, but must incorporate mining and waste management protocols. Dwindling resources like water and energy also demand innovative approaches for lowering consumption and/or promoting recycling along the value chain. Addressing such challenges relies on appropriate characterisation of ore behaviour under different process regimes. Coupled with this, emerging characterisation tools are increasingly applied to understand the mineralogy of unconventionallypresented and difficult-to-process ores to meet societal and technology demands. Such tools are often accompanied by the generation of large, computationally intensive datasets, for which data management and storage are key requirements, particularly when deciphering temporal trends in ore and process variability. This paper will elaborate on these themes with examples that highlight the importance of process mineralogy throughout the minerals value chain. Keywords: Process mineralogy, ore characterisation, geometallurgy

Jan 1, 2020

By J. L. Jambor, J. E. Dutrizac, J. B. O'Reilly

The present-day metallurgical community is quite familiar with the use of jarosites [MFe3(S04)2(0H)6 where M = K, Na, NH4, Ag, 1/2Pb, etc.] as a means of controlling iron, alkalis and sulphate in hydrometallurgical circuits. This modern precipitation technology has found an increasingly widespread application in the zinc industry111 and is gradually also being extended into the hydrometallurgical processing of copper and cobalt121 . The chief advantage of jarosite precipitation is that the iron precipitate settles and filters well, and gives low losses of divalent metals in the washed residue. Although this jarosite precipitation technology was developed only within the past twenty years, man's involvement with jarosites extends back to antiquity, and jarosites have played an important role as a source of silver in several ancient metallurgical centres. In the early days of this century, argentojarosite was an important local source of silver at the Tintic Standard mine, Dividend, Utah, where over 200 000 oz of silver were recovered from highgrade natural jarosite over a three-month period 131 . At the Matagente mine in Peru, pockets of argentiferous plumbojarosite up to 40 m thick were mined and processed by the Indians prior to the arrival of the Spaniards14-51 . In Cyprus there are vast jarosite deposits associated with the ancient mining sitesl51 , but exploitation of these jarosites has been insignificant because of their low silver values. The most extensive mining of silver-bearing jarosite, and certainly the oldest documented instance of such jarosite exploitation, was in the vast pre-Roman workings at Rio Tinto, Spain. This mine, the greatest single miningmetallurgical site currently known from the ancient world and also the oldest site of more or less continuous metal production, has witnessed many metallurgical firsts. Aside from the initial processing of jarositic ores for their silver values, the development of large-scale hydrometallurgy also seems to have occurred at Rio Tinto. As early as 1737, copper was recovered by cementation on scrap iron from the mine waters at Rio Tintol51 . Large-scale heap leaching of calcined ore commenced with the British operations in 1876 and, by 1900, raw pyrite was heap leached to recover associated copper values161 .

Jan 1, 1999

By M. Bilal Khan

Thermal stress relief by means of a typical heat treatment cycle (660oC for one hr) is compared with the one achieved through vibratory stress relief at resonant and multiple resonant frequencies for the D-406 HSLA material. Our analysis of the data is based on the microhardness profiles measured for the entire length of scales, namely, base metal, heat affected zone (HAZ) and the weld bead itself. The profiles obtained using the two techniques mimic each other, for an equivalent 70% stress relief level. The data are further qualified by impact testing wherein the zone of interest is projected in the retention groove to provide impact by the pendulum striker in the Charpy mode. Higher equivalent energy absorption in the treated specimens confirms the efficacy of the vibratory method. The present work rectifies earlier anomaly where heat treatment has been reported at 310oC for the same material.

Jan 1, 2009

By Ketan H. Trivedi

This paper describes the method of analyses used for the design of temporary and permanent Secant Pile Walls, describes various aspects of construction including, guide walls, sequence of pile installation, plan alignment and verticality tolerance, methods of drilling (auger, wash boring, cased and open holes), lateral bracing for secant piles, cutting of keys in secant pile walls for the connection of permanent floor slabs, sealing of water leaks and waterproofing. The paper concludes with a brief case history of a secant pile wall project recently constructed in New York City.

Jan 1, 2006

By Liang Shen

The Cooper River Bridge, the longest cable-stayed bridge in North America, replaces two existing bridges along U.S. Highway 17 and connects the City of Charleston and the town of Mount Pleasant, South Carolina. Two diamond shaped towers support the 1,546 ft long main span over Cooper River and allows for a 1000 ft wide navigation channel. The Charleston high-level approach is 4351 ft long and provides a 250 ft wide navigation channel for Town Creek, while the Mount Pleasant high-level approach is 2,090 ft long. Due to the high seismicity in the region, potential vessel impact, and hurricanes, large lateral loads are expected. From various types of foundations, 10-foot diameter drilled shafts were selected for their high capacity against vertical and lateral loadings. The shafts are founded on a stiff to very stiff lightly cemented calcareous sandy clay or sandy silt layer, called Cooper Marl, which underlies the coastal sediments of the interbedded clays and sands. A group of 11 shafts supports each main tower, while a rock island protects it from vessel collision. A group of 4 to 8 shafts foundations support the other piers of the main span unit. A pair of shafts supports the High Level Approach piers. The shaft tip elevations vary from 120 ft to 230 ft below water line. An elaborate geotechnical investigation was conducted on the site, including a load test program on full-scale shafts under axial and lateral loads. The results of the tests were used to calibrate the lateral and axial soil resistance. The objective of this paper is to present the different aspects of the bridge foundation design.

Jan 1, 2013

By P D. Kasbanis, Lyall Workman

"The energy output of an explosive is typically calculated using an equation of state and computerapplications. Results are reported as weight and bulk strength, either in absolute terms or relative toANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of “available energy” associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated."

Jan 1, 1996

By D. Harrington

"FOREWORDVirtually all government agencies undertook many additional responsibilities during the period immediately preceding World War II; these responsibilities increased vastly in importance and scope after the actual declaration of war following the attack on Pearl Harbor. The Bureau of Mines was one of the agencies thus affected, and it was called upon to perform many duties foreign to its normal peacetime activities.The Health and Safety Division of the Bureau of Mines, at that time designated the Health and Safety Branch, was given several important and difficult duties and responsibilities of an unusual nature because of the war while of necessity-continuing its normal functions of assisting the mineral industries in the preservation of life and health and the protection of property, this being of especial importance in wartime because of the pre-eminent importance of having maximum output of essentially all types of mineral products. Some of these additional functions were given to the Health and Safety Division because the organization of the Division, with its field set-up dividing the Nation into districts with competent, experienced personnel in charge of its work, provided the nucleus of personnel and procedure through which rapid and smooth expanded functioning was feasible.In addition to the responsibilities directly attributable to definite war activities, such as the administration of the wartime Federal. Explosives Act and the Mineral Production Security Branch a new branch (then designated division) was formed to investigate coal-mine health and safety problems after the enactment of the Federal Coal-Mine Inspections and Investigations Act, which became a law on May 7, 1941, but which actually began to function actively after the declaration of war in December 1941.The purpose of this publication is to provide a brief historical record of the activities of the Health and Safety Division as a whole and of its individual branches during the war. The detailed record has been filed in the Archives Building, Washington, D. C."

Jan 1, 1949

Ammonium nitrate-fuel oil (ANFO) explosives are unstable in hot, reactive sulphide-rich ground at Mount Isa. Under certain conditions associated with background heat, moisture, and chemical impurities from natural oxidation, ANFO composites in contact with hot ground disproportionate and the ammonium nitrate can undergo rapid exothermic reactions with sulphide.Reactions can occur in confined charges from prolonged contact with reactive sulphides, or by contamination with sulphide in loading. Partial interaction can result in misfires or premature detonation. Spilt, scattered and unpropagated explosive will undergo further reaction in sulphide-rich environments. ANFO-sulphide interaction is invariably exothermic and causes an irreversible chemical transformation of the ore.The heat generated during reaction may be dissipated, heating the environment, or rapidly accumulated to yield hot spots or areas in excess of 400°C. These can result in forced ignition of bulk sulphide and sustained combustion.Thermal analysis was used to define the critical conditions for ANFO-sulphide interaction and sulphide combustion.The occurrence of incandescent ore is attributed to the thermal interaction between exothermic hydrolysis oxidation, ANFO-sulphide, and combustion processes.Chemical agents and control methods have been developed to prevent ANFO-induced oxidation and combustion.

Jan 1, 1968