Search Documents

By T. P. Mucho

Over the past several years, two types of roof control problems have been en- countered at Beth Energy's Eighty Four Complex mine in Southwestern Pennsylvania. These problems have been (1) poor roof conditions encountered while advancing submain entries and longwall panel entries and (2) deterioration and failure of long- wall gateroads, principally the tailgate entry. This paper discusses the efforts by mine personnel to analyze the origins of the various attempts to-deal with the problems, and the success (or failure) of these efforts. Highlighted are the use of various common roof Control materials, variations in mining techniques, cementatious pillars, and changes in pillar design using yield and abutment pillars to address these problems.

Jan 1, 1986

By Geoffrey C. Hebner

Augered, cast-in-place piles (ACIP) have become a very common foundation type in Atlanta and the Southern Piedmont Province as well as much of the United States in the past 20 years. Prior to the introduction of ACIP foundations in Atlanta, the most common deep foundation type was Raymond piles. Raymond piles are basically a driven, thin-walled step-tapered steel pile filled with concrete. Drilled piers were also relatively common and continue to be used, particularly in shallow bedrock or high column load situations. Driven piles, including pipes, H-sections, and timber piles were previously common with working loads typically in the 30 to 50-ton range. Initially, ACIP foundations had similar allowable capacities, however, over time improvements in installation techniques and equipment have resulted in an increase in allowable ACIP capacities. Correspondingly, they have become a more cost-effective and trusted foundation for geotechnical and structural engineers. Over the next several decades many other deep foundation alternatives began to lose popularity. ACIP are one of the predominant deep foundations in Atlanta and the Southern Piedmont today. Although ACIP foundations have widespread popularity in the private sector, they have not been readily accepted currently by government transportation agencies. ACIP may be used by some of the smaller municipalities, but to the author's knowledge, have not been used with regularity by larger, state agencies.

Jan 1, 2003

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By G J. Corbett, P Magner, M McKenzie

Structures formed during ductile deformation have been reactivated during the later brittle mineralisation process. Two generations of folding are classified as: early recumbent megascopic FI folds and FI shears which transpose the hinge regions, and later upright F2 folds. S1 is folded about F2 folds which contain axial planar S2 crenulation cleavage. Vergence relationships between S1 and bedding indicate that many of the mineralised structures occupy sites of FI folds which have acted as plumbing systems for later gold mineralisation (eg Blackwater mine). The Globe-Progress gold mineralisation is localised by a major jog formed by sinistral strike-slip movement on two FI fault segments and mineralisation also occurs in smaller jogs along strike (eg Sir Francis Drake, Happy Valley-Merrijigs, Cumberland).   The lodes of ribbon quartz which exploit the FI shears and local bedding planes, are inferred to have mostly formed after the peak of metamorphism, possibly related to the emplacement of Carboniferous granites. This was followed by a sequence of vein deposition and wallrock alteration which consists of quartz-As/Fe sulphides ? carbonate - stibnite ¦ trace base metal sulphides and Bi-sulphosalts ? illitic clay/sericite-chlorite. Gold at Globe-Progress is mainly encapsulated in arsenopyrite. At Blackwater, free high fineness gold occurs in partings in lode quartz with late sericite-chlorite. The above sequence of events is comparable to that encountered in many intrusion-related gold systems throughout the Southwest Pacific region. There is a spatial relationship between gold mineralisation and dykes variably described as diabase, dolerite or lamprophyre. Alkaline rocks occur in many Pacific rim and older goldfields and may possibly be related to a magmatic source for gold mineralisation.

Jan 1, 1997

By K. E. Stanfield

[Asphalt and road oil are the principal products manufactured from Wyoming ?clack oils? which, because of their high asphalt an high sulfur content, are difficult and costly to refine into high-grade motor fuels, burning oils, and lubricants by pre sent methods. Accordingly, the remand for these asphaltic residuums for the construction of roads and other uses is a controlling- factor in the quantity of crude oil produced. The increasing utilization of special asphalts as inexpensive bonding, insulating, and waterproofing materials indicates the desirability of obtaining information on the yield and properties, of asphalts from Wyoming black oil to promote a wider and more stable caret for these asphaltic materials.]

Jan 1, 1941

By N. Merriam

This report describes Koppelman's work to develop the K-Fuel® Series C Process used to dry and stabilize Powder River Basin coal. It also contains summaries of the results of bench-scale and pilot plant tests conducted to prove the Series C Process. The process is being used by the KFx-Thermo Ecotek partnership for a 500,000 ton per year commercial plant that has been constructed near Gillette, Wyoming. The plant is presently undergoing shakedown.

Feb 24, 1997

By V. A. Akinbinua

This work is intended to examine the relationship between rock fragments produced during compression tests using a soft testing machine, e.g. hydraulic press (the machine used in this work is Amlser rock testing machine), and the rock fragments size distribution produced by fragmentation of the same rock through application of explosive. The rocks tested are fine grained marble, medium grained tonalite and fine-medium grained granite, medium grained norite and medium grained gabbro. The rocks types are prepared according to ISRM methods to be tested for strength determination. The rocks are loaded at constant load until failure. The fragments resulting from the failure of each of the rocks types are collected for size characterization by sieve analysis. The same rocks tested under soft testing machine are also prepared into blocks of dimension 150 mm length x 100 mm width x 100 mm height for blasting by explosive application. Each block of the different rocks are drilled through with an 8 mm diameter drill to a depth of 80 mm. Each of the holes on the blocks is spaced from each other at 44.7 mm and with a burden of 28 mm. The holes therefore formed a rectangular blasting pattern. Each of the holes was charged with a 720 mg electronic detonator and fired instantaneously inside a cylindrical blasting chamber. After each shot, the fragments are collected for size characterization. The sizes distributions from blasting are compared with sizes distributions resulting from rock testing using the parameter Xc of the Rosin-Rammler distribution function (RR) and 75% cumulative percentage passing. The analysis and finding from this work is presented in this paper.

Jan 1, 2014

When the first rush of miners took place on the Molyneux River, in the Dunstan Gorge, the gold was won by means of cradling the gravel, which was shovelled from the various beaches and crevices in the rock-bound sides of the river.The above method of winning the gold was only practicable when the beaches were not covered with water, hence the work was usually carried on during the winter months, the ordinary level of the river during spring and summer months being some ten or twelve feet above winter level. The melting of the spow in the Lakes water-shed being responsible for the high summer level of the river.As the available beaches were worked out, other methods of winning the gold were proposed and worked with more or less successful results the first advance being to work the bed of the river by means of a spoon dredge. The spoon was made with a round lip or ring of iron, having a steel cutting edge on one half of the circumference, at the opposite side a socket being forged to take a long spar or boom, which was securely fitted thereto. At intervals round the hoop, half-inch holes were bored to enable. a bullock-hide bag to be laced on to same. The spoon was worked from a pontoon which carried a crab winch, tackles and the necessary washing appliances to treat the washdirt lifted. In starting to dredge, a tackle was attached to near the upper end of the boom, and a line or chain was carried over a cat head from the crab winch...

Jan 1, 1901

By Robert F. Randolph

Introduction This paper is a descriptive analysis of injuries and fatalities at small surface bituminous coalmining companies in Pennsylvania. The purpose of analyzing a specific industry sector and location is to identify issues that might be missed in a wider analysis. Other studies of small mine safety (e.g., Peters and Fotta, 1994, Randolph and Boldt, 1997) have shown that the relationship between safety and mine size is not a simple one. Some injury types occur at higher rates at small mines, while others occur at lower rates. Consequently, an analysis limited to a specific type of mining can help identify hazards and issues specific to that sector. The results of this analysis will be useful for directing training, intervention, and research efforts towards the most prevalent causal factors and incident types. Procedures and Definitions Data sources The primary sources of data for this analysis were files provided by MSHA containing information collected under Title 30 Code of Federal Regulations, Part 50. These files, commonly referred to as “Part 50 data”, are provided though MSHA’s Program Evaluation and Information Resources directorate. Two primary types of injuries were selected from the Part 50data: Fatalities (MSHA “degree of injury” code 1) and lost-time injuries, otherwise known as nonfatal with days lost (MSHA “degree of injury” codes 2 through 5). Lost-time injuries involve either actual days away from work or days of restricted activity or both. Fatality and lost-time injury incidence rates were calculated using the standard MSHA formula: Number of injuries per 200,000 employee-hours. Additional information on company sizes and mine ownership was provided by the Pennsylvania State University College of Earth and Mineral Sciences. Time span A five-year time span was selected for this study. More than a single year of safety experience is usually needed to capture a broad range of incident types. Many types of injuries, especially fatal injuries, can be extremely rare, and may be missed if too short a time span is selected. However, a time span that extends too far back may begin to suffer historical threats to validity. That is, incidents that occurred several years ago may be caused by hazards that have since been remedied or may be related to mining practices and conditions that no longer exist. A five-year span offers a practical compromise between these two concerns. Consequently, the MSHA Part 50 data files from 1993 through 1997 were used. The 1997 file was in “preliminary” form at the time of the study, so small variations from the final 1997 “close out” file can be expected. Based on past experience, we do not expect the close-out variations to have a significant impact on the findings.

By L. E. Eary

Many of the major international gold mining companies provide data on rates of greenhouse gas (GHG) emissions as part of their environmental reporting commitments. These data are evaluated by an index defined as the annual GHG emission rate in metric tons, divided by the annual amount of gold produced in grams, and referred to as GHGgold. This paper examines ranges of GHGgold values for a cross section of gold mines as a function of mining method (openpit, underground and combined operation) and ore-processing method (mill, heap leach and combined methods) for reported ranges of operational data, including annual total tons mined, ore processed and gold grade. The evaluation shows that ranges and distributions of rates of GHG emission are approximately similar across different mining methods and ore-processing methods. The data presented in this paper provide the context needed to make comparisons of GHG emissions reported in companies’ annual reports to the ranges reported for the overall gold mining industry.

Jan 1, 2009

By Warren L. J, Horsley R. R, Meagher L

Mineral concentrators often use process water that is very saline and/or hard. In this paper the effect of increasing concentrations of sodium chloride and calcium chloride on the rheological properties of 70 wt% quartz suspensions (d5o - 10.6 ¦m) is reported. The apparent viscosity at 100 s t in 5 mol dm -3 sodium chloride solutions (approx. 300,000 ppm) was nearly 500 times the viscosity of water without salt or particles present. Part of the increase in viscosity is caused by aggregation (coagulation) of the suspension.

Jan 1, 1989

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

Mining education has received almost continuous discussion since its inception and most people engaged in the mining industry and in mining education feel at some time the urge and necessity to express their views. This paper is not a comprehensive survey of past and present practices and accepted principles, but a personal opinion of the form mining education should take at university level. It is expressed because of a dissatisfaction with the existing courses offered to students. It is hoped to provoke discussionand bring forth guidance to those engaged in mining education. After all, students spend four or five years at a university and it is desirable that the graduate should be something more than just those many years older at the end of his course.POST GRADUATE EMPLOYMENTThe first problem confronting the university should, be to discover what the mining industry wants and expects or graduates. This must influence the university course and yet universities have done little to seek this information, and if suggestions have been offered by industry; universities appear to have made little use of them. University mining curricula are basically what they were 50, 100 and even 200 years ago. (See Appendix.) Whether this reflects the unchanging problems of mining the wisdom of early professors, the conservatism of subsequent professors or inability to apprectate necessity for changes, is debatable.Unfortunately there is no uniformity in the type of employment offered to new graduates: Some mining...

Jan 1, 1959

By James Ransford Dankwah

This work investigates the effect of waste plastics addition on the reduction of iron oxide by sawdust. Composite pellets of iron oxide containing sawdust (SD), high density polyethylene (HDPE) and blends of SD/HDPE were fired under argon in a horizontal tube furnace at temperatures between 1300 and 1500 °C. Reduced samples were weighed after 10 minutes of reduction and the extent of reduction was calculated from the measured oxygen contents of the compact. The results showed improved extent of reduction when SD was blended with HDPE. The highest extent of reduction was achieved at SD:HDPE ratio of 2:3.

Jan 1, 2014

By F T. Suorineni, L Baird, A Papaioanou, D Hines

The Mathews et al (1981) stability graph was developed to provide guidance in the determination of stope sizes to control dilution in bulk mining of large orebodies. Longhole and sublevel open stoping (LHOS and SLOS) are the lower end in scale of underground mass mining with panel and block caving (PBC) at the higher end. Currently, the stability states of stopes in the stability graph are described qualitatively as stable, unstable or cave. The alternative quantitative option to the qualitative stability graph is the Equivalent Linear Overbreak Slough (ELOS) stability graph. The ELOS stability graph only applies to narrow vein orebodies. It is easy for the Mathews et al (1981) and the ELOS stability graphs to be applied outside the limits of their databases. What is currently referred to as ‘stable’ in the present stability graphs has diverse interpretations at different mines depending on their acceptable dilution values. In 2014, a research program was conceptually conceived at the UNSW Australia School of Mining Engineering to develop a quantitative dilution-based stability graph independent of orebody width to address some industry concerns on the use of the stability graphs. A dilution-based stability graph provides the mining engineer the flexibility to determine open stope sizes based on what dilution amounts are acceptable. The graph also unifies both the Mathews et al (1981) and ELOS stability graphs for wide and narrow vein orebodies, thus, eliminating their potential misapplications. To date, the concept is proven with case studies from metalliferous underground mining operations located across Australia. This paper presents the dilution-based stability graph concept, the initial results and future plans to account for other critical factors and increase confidence in its application with the addition of more data outside Australia.CITATION:Suorineni, F T, Papaioanou, A, Baird, L and Hines, D, 2016. A dilution-based stability graph for open stope design, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 511–522 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By B S. Utting, W J. Cowie

The alluvial gold industry of New Zealand is based on the placer deposits in Otago and on the West Coast. Production from these since discovery in the 1850s has been an estimated 480 t (15 Moz) of gold. Annual output has expanded continuously since 1980 and is expected to be over 2 t of gold for 1989. Following a historical review, the characteristics of typical operations, which use hydraulic excavators and mobile trommel units are discussed. Descriptions are then given of alluvial activities in Otago and on the West Coast.

Jan 1, 1990

By Gustavo Quiquia Mucha

El presente texto describe las experiencias realizadas por la Compañía Minera Milpo SAA en el marco de una gestión social basada en la consulta previa, libre e informada en la Exploración Minera Responsable. En ese sentido, es importante la cooperación entre la empresa minera y la comunidad, así como la incorporación del marco ideológico empresarial y metodológico, basado en los principios del Convenio 169 de la OIT sobre Pueblos Indígenas y Tribales en Países Independientes, las estrategias y las líneas de intervención social de la Compañía Minera Milpo SAA en los proyectos de exploración minera responsable.

Sep 12, 2011

By Z. Q. Zhou

It is the first worke in design of pile foundation to determine the carring capacity of single pile, and a static loading on site is considered to be the lost derect and reliable way. All values P and settlements S induced can be plotted as a broken-line. Since soil is a kind of elasto-plastic and cohesive material, the increasing of settlements is generally greater than that of loads. Different value Pu nay be given by different tester on his P-S diagram, because of erroys in the test and complicated, characteristics of soil. The analytical method of exponential equation shown in this paper derives a specified solution. After using an exponential curve to regress values of loads P and corresponding settlements S from on-site test, coeficients A and B of exponential equation can be obtained. With this curve an ultimate carrying capacity of single pile can be determined. The resistant forces of pile shaft and pile tip can also be defined by the tangent of the calculated knee point, as it is called (tangent method). At last, an example is given to show how the ultimate carrying capacity of f 500mm bored pile is obtained with this method for a project in Kunming.

Jan 1, 2010

Most types of nuclear power reactors use uranium dioxide fuel. Power reactors using natural uranium dioxide fuel are of special interest to countries such as Australia that have their own uranium supplies. A wide range of uranium dioxide powders can be fabricated and the ideal one flows readily, presses without the need for binders or lubricants, sinters to the required density and gives low reject rates at all fabrication stages. Sinterable uranium dioxide is usually produced via the ammonium diuranate route.The Australian Atomic Energy Commission is aiming to demonstrate production of nuclear grade uranium dioxide from Australian concentrates, improving technology where possible. Details are given of the dissolution, solvent extraction, precipitation, filtration, drying, and· calcination-reduction steps. Solvent extraction from sulphate media is also under study with a view to developing a process to produce a nuclear grade product at the mine treatment plant site.

Jan 1, 1970

By P. H. Derbyshire

The use of continuous flight auger piles has increased significantly in the U.K. to such an extent that it is now the most widely used method of constructing small diameter bored piles. This paper describes the improvements in equipment, techniques and particularly monitoring that have led to this growth. A review of the equipment in use describes how purpose built self erecting machines have been generally adopted. Improvements in ancilliary equipment are described. Concrete has almost completely replaced grout and techniques have been developed to extend the length of reinforcement that can be placed. Leading specialist contractors have developed instrumentation to monitor the construction of the pile (in terms of time, depth, torque, concrete pressure and flow) and keep a record for checking. A further significant development of this monitoring by means of sensors at various levels in the auger stem is described. The results obtained from this monitoring are reviewed and future developments discussed.

Jan 1, 1989