Search Documents

By X. Q. Jiang, D. L. Chen, A. Macwan

Magnesium alloy, being the lightest structural material, is a key candidate for the weight reduction of vehicles in automotive and aerospace industries; however, its poor corrosion resistance and difficulty in deformation are limiting factors. Recently, Al/Mg/Al tri-layered clad sheets have been considered as a promising alternative to improve corrosion resistance and formability of magnesium alloys. The aim of this study was to evaluate the tensile properties and deformation behavior of Al/Mg/Al tri-layer clad sheets at different temperatures and strain rates. Yield strength (YS), ultimate tensile strength (UTS), and elongation were observed to increase with increasing strain rate. With increasing temperature from -40°C to 180°C, YS and UTS decreased and ductility increased. The strain hardening exponent evaluated via three equations of Hollomon, Swift, and Afrin et al. showed a similar increase with increasing strain rate and decreasing temperature. The fractographic analysis showed partial debonding of clad interface especially at higher strain rates and lower temperatures.

Jan 1, 2015

By A. Hashempour, D. Javani

"Selection of an optimal bit is a critical issue in drilling engineering. Specific energy (SE) and Cost per Foot (CPF) are the most common methods for evaluation of bit efficiency and optimal bit selection. The major shortfall of both methods is that they do not directly account for geological and geomechanical parameters of formations being drilling. In this paper, results of using the two foregoing methods are compared using Formation Drillability (FD) method, which directly accounts for geological and geomechanical parameters of a formation. This method combines various geological and geomechanical parameters and yields a dimensionless parameter indicating the formation drilling hardness (drillability). Results of this study show that the amount of energy, cost and time spent for drilling a unit volume / length of an identical formation may vary in different wells. This is due to the fact that geological and geomechanical characteristics of a formation may vary among wells and even within short intervals of a single well. Therefore, an optimal bit may not be appropriately selected, if drilling and economical parameters are the only factors considered and the formation geological and geomechanical specifications are ignored.INTRODUCTIONMany authors such as Bilgesu, Al-Rashidi, Aminian, and Ameri (2000) and Clegg (2006) conducted research in the evaluation of bit performance and optimum bit selection. Almost all of them tried to establish a good relationship based on geomechanical parameters. Primary examples are the research done by Ubaldi (1999), Macini, Magagni, Da Dalt, and Valente (2007)."

Jan 1, 2015

By Q. F. Wang, M. H. Lai, T. Q. Liu, G. G. Dong

Compared with the traditional pre-treatment process, biological oxidation process has many advantages including higher gold recovery, less cost, easier operation. The bio-oxidation reactor is the most important equipment for biological oxidation process. In this paper, the characteristics of biological oxidation are investigated, and the design principles are proposed based on laboratory tests. Both increasing the tank height and taking new inflation system can enhance higher dissolved oxygen. The new type of large-scale industrial bio-oxidation reactor is designed, which is 9.5 m in diameter and 10 m in height. The bio-oxidation reactor metallurgical performance has been tested by industrial-scale experiment. The slurry of flotation concentrate is divided into two parts to feed two bio-oxidation reactors. The feeding rates of two reactors are adjusted on the basis of getting the same content of S, Fe, As in overflow. The result shows that the feeding rate of the new type of 700 m3 bio-oxidation reactor is 3.72 m3 per hour, and the feed rate of the conventional 700 m3 bio-oxidation reactor was 3.23 m3 per hour. The processing capacity of the former is 15.2% higher than that of the later, which demonstrates the new type of bio-oxidation reactor has higher oxidation rate.

Jan 1, 2015

By G. O. Oniyide, H. Yilmaz.

"This paper presents the result of the research done on the effect of temperature on the dilatancy of rocks from the Bushveld Igneous Complex (BIC), where the South African Platinum mines are located. The BIC has higher virgin rock temperature (VRT) than the gold mines of the ‘Witwatersrand Basin Complex’. If the platinum mines advance to ultra-deep levels as the gold mines, since the Merensky Reef has been reported to extend beyond 5km, then the virgin rock temperature at 5 km below surface would be approximately 140oC. Hence, there is a need for the investigation of rock behaviour at high temperatures. Five different rock types (norite, leuconorite, mottled anorthosite, pyroxenite and chromitite) were tested in a 2600 kN servo-controlled multi-purpose triaxial testing machine. The tests were done at a constant strain rate of 5 x 10-1 S-1 and a confining pressure of 10 MPa within temperature range of 20 °C (ambient temperature) to 140 °C. The results show a general strength reduction and increasing dilation angles with increasing temperatures. The results also demonstrate that dilation angle is close to the internal friction angle at lower temperatures; however, they are greater at higher temperatures.INTRODUCTIONMany challenges are faced with increasing depth of mining in underground mines. The most obvious are heat, in-situ stresses and those associated with logistics. Issues related to underground heat have mainly focused on the side effect of heat on workers' health, increasing production costs as a result of higher cost of ventilation. The effect of increasing temperature with increasing depth on the behavior of rock has not been given much consideration. Generally, gold mines in South Africa are deeper than the platinum mines but the latter have higher temperature gradient, which makes the platinum mines to be warmer at similar mining depths. Although the study of the effect temperature on the behaviour of rock can be beneficial to both gold and platinum mines, the focus of the research is limited to the platinum mines because of their higher temperature gradient. Donoghue (2004) stated that the virgin rock temperatures (VRT) and air temperatures increase with depth, due to the geothermal gradient and auto-compression, that is, compression of air by its own weight."

Jan 1, 2015

By R. Panchadhara, P. A. Gordon

"A non-local formulation of the classical continuum mechanics theory called peridynamics is used to study driven dynamic fractures in the near wellbore region. The controlled application of pressure on the inner walls of the borehole can create multiple fractures that initiate from the borehole and propagate radially outwards. The number of fractures and their final length is primarily controlled by the loading conditions and the in-situ stress state. It is the objective of this study to use a novel numerical technique called peridynamics to investigate: 1) the influence of loading conditions on the fracture pattern, and 2) the effect of in-situ stress anisotropy on fracture propagation. In peridynamics, the momentum equation from the classical theory of solid mechanics is replaced with the integro-differential momentum equation of peridynamics. As a result, discontinuities in the body, such as fractures, occur spontaneously. The material is represented by a continuum body with material points that interact non-locally with all other points within a specified distance. Fractures evolve using a damage evolution law, wherein, damage at any point is represented as the ratio of the number of broken bonds in the current configuration to the total number of bonds in the undeformed configuration.Simulations are performed on simplified test cases and the results are compared to relevant experimental and numerical studies found in the literature. It is shown that the loading rate significantly influences the number of fractures initiated from the borehole as well as their extent. Low loading rate produces fewer fractures, whereas, high loading rates produce longer and a greater number of fractures from the borehole. The numerical method successfully predicts the fracture pattern obtained from a wide range of loading conditions. Predictions also indicate that the resultant fractures are shorter when in-situ stress is applied. Numerical results show that the fracture extension is largest in the direction perpendicular to the minimum compressive stress for the range of loading rates used in this study."

Jan 1, 2015

By B. Panton, J. Carvalho, E. T. Brown

High-capacity, post-tensioned anchors have found wide-spread use in initial dam design and construction, and in the strengthening and rehabilitation of concrete dams to meet modern design and safety standards. Despite the advances that have been made in rock mechanics and rock engineering during the almost 80 years in which post-tensioned anchors have been used in dam engineering, some aspects of the rock engineering design of high-capacity rock anchors for dams have changed relatively little over the last 30 or 40 years. This applies, in particular, to the calculations usually carried out to establish the grouted embedment lengths required for deep, post-tensioned anchors. These calculations which involve a number of aleatory and epistemic uncertainties, usually make simplified assumptions about the distribution and values of rock-grout interface shear strengths, the shape of the volume of rock likely to be involved in uplift failure under the influence of a system of post-tensioned anchors, and the mechanism of that failure. The resulting designs are generally conservative. These aspects of the rock engineering design of large, post-tensioned rock anchors for dams could be improved by making greater use of modern, comprehensive, numerical analyses in conjunction with 3D models of the rock mass structure, realistic rock and rock mass properties, and the results of prototype anchor tests in the rock mass concerned.

Jan 1, 2015

By J. G. Kim, B. G. Chae, D. S. Cheon, E. S. Park

The underground structures such as high-level radioactive waste disposal thermal energy storage should be designed and constructed considering thermal-mechanical characterization because of long term and/or cyclic thermal stress. High temperature changes in these structures can extend the existing cracks and generate new cracks in surrounding rock mass. In case of long term and/or cyclic thermal stress conditions, it is possible to lose the function of structures caused by the significant cracks and fracture growth in the rock mass. In this study, the critical thermal crack temperature of the granite, limestone and thermal Kaiser effect were evaluated. Experiments were carried out with the heating speed of 1.5?/min. To avoid thermal shock and target temperatures were set at 150? and 250?. In order to verify the thermal Kaiser effect, the samples were heated by 150 ? after 2-3 repetition to 250?. The generation and growth of cracks were observed through an acoustic emission measuring system. The variation of the physical rock properties was measured before and after thermal experiments. After compared with the thermal experiments using PFC2D, numerical simulations were carried out at higher temperatures (400?). The experiments showed that the initial thermal crack temperature of granite and limestone is about 35?, 32? and the critical thermal crack temperature were about 69? , and 49? , respectively. The experiments confirmed the thermal Kaiser effect of experimented granite and limestone due to thermal cyclic loading. From the numerical analysis, the critical crack temperature showed the same tendency as the thermal experiments. The P and S wave velocity of the sample after the experiment were reduced. Therefore, when heat is applied in long-term and repetitive conditions, these cracks may affect the function and stability of the underground structure. Therefore, further studies of thermal stress effects should be performed.

Jan 1, 2015

By T. Johnson, K. Lambrych, D. Kelley

Materials for construction of equipment used in hydrometallurgical plants are selected based on a combination of their ability to perform as required in aggressive process environments as well as their cost. As a material of construction, fiber reinforced plastic (FRP) has been shown to provide equal if not improved durability relative to alternative materials such as corrosion resistant alloys at a considerably lower cost. This is particularly true in the case of equipment used in acid leaching processes for copper, cobalt, nickel and rare earth elements. The selection and extensive use of FRP over alloys in new hydromet plant construction in North and South America illustrates this advantage of FRP effectively. This paper will compare corrosion performance and cost of plant equipment fabricated with stainless steel alloys and FRP made with Epoxy Vinyl Ester thermoset resins. Real world case histories for FRP piping, storage tanks, extraction vessels, and electrowinning cells combined with laboratory based corrosion studies will be reviewed to demonstrate how FRP materials are selected for hydrometallurgical equipment.

Jan 1, 2015

By H. Kuno, H. Kobayakawa

A borehole inclinometer with FBG optical fiber sensors has been developed to clarify very slow slope movements, and the results of its application to a real slope have been shown. The main characteristics kept in mind while developing this inclinometer are as follows. Firstly, the workability must be good so that only one cable is required for taking the measurements, because the inclinometer is composed of several FBG sensor elements constructed on an optical fiber. Secondly, the minimum interval of the distorted measurements must be close, namely, within 100 mm. Thirdly, the inclinometer must excel in thunder resistance. The measurements were executed by setting up the developed borehole inclinometer on a slope where the rate of displacement is several millimeters per year. The movement of the device was developed by comparing it with that of the results of an existing borehole inclinometer. The area of the displacement concentration, 1 m in width for 4-m sections, was confirmed by the existing borehole inclinometer. The boring core, recovered using a high-quality drilling technique, was examined. Landslide clay was not permitted at the location where the displacement had concentrated as a result of comparing the measurement results with the boring core, and the rotation of gravel by the movement of the slope’s land block was allowed. These results show the slope being caught in the stage just before a primary landslide. In addition, the feature whereby the slope behavior depends on the depth was analyzed by comparing the information on the underground displacement with precipitation and earthquake records.

Jan 1, 2015

By Hidekatsu Takeuchi, Masaru Sakakibara, Shigeo Tanabe, Kenji Harada, Akihiko Suzuki, Shoji Morihana

"Deep mixing (DM) method, one of the most commonly used solidification methods, is based on the principle of solidifying soft ground. It can be classified into two categories such as Cement Deep Mixing (CDM) method and Dry Jet Mixing (DJM) method which apply hardening agent in slurry condition and in powdery condition respectively. In recent years, DM methods have undergone changes that have evolved them from the traditional method to meet the needs of the diversifying market. Among them, the Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method is a DM method which mixes a cement-type hardening agent in slurry condition mechanically with soils in situ and incorporates the innovative technique, “atomized ejection” that has been developed to allow faster installation of larger diameter columns without sacrificing quality compared with conventional methods. At this technique, the atomized hardening agent is discharged together with compressed air through a device incorporated into the mixing blade. It also has advantages of performing the works with low-displacement of the surrounding soils in consideration of environmental friendliness and with higher penetration capability against hard ground.This paper presents the technological outline of the above-mentioned CI-CMC method, focusing on the atomized-ejection technique, followed by some construction examples, applied to the self-earth-retaining wall, to the hard ground and the area adjacent to the existing structures.INTRODUCTIONAccording to the accumulation of its case histories, Deep Mixing method has been receiving the demands of its application to more challenging conditions, such as harder ground condition, and requirement of lower displacement of the surrounding ground during its operation. In addition, to match its price against the other cheaper methods and widely receive its benefit of higher quality, the cost reduction of Deep Mixing is also one of the major challenges. For the cost reduction, higher productivity and lower consumption of the material to obtain the equivalent strength and homogeneity with the conventional method are required.The Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method has been developed to meet these demands. CI-CMC incorporates the mist ejection that has been developed to achieve faster installation of larger diameter columns without sacrificing quality compared with the existing methods. Normally, we obtain cement columns of about 1.0 m in diameter by using Deep Mixing method. To increase the productivity, it is not preferable to drastically increase the penetration and withdrawal speed of the mixing blades because of the hardness of the ground and restriction by minimum number of passage of rotating blades per a certain height of the soil cement. Instead, the expansion of diameter of the columns will simply increase the productivity. The development of the new mist ejection system, as shown in Photo 1, has enabled the diameter of soil cement columns to 2.0 m on single axis while 1.6 m on double axes. Mist ejection means that the hardening agent slurry is sprayed into the ground in mist form together with compressed air thereby achieving homogeneous mixing and reducing the resistance on rotating blades."

Jan 1, 2015

By D. Settles, R. Rose, P. L. Dunn

"A new mineral sands operation is being developed in Georgia by Southern Ionics, Inc. (SII). Prevailing mineralogy and certain design constraints required detailed testing and circuit analysis to create a robust separation processes. The floating wet concentrator plant (WCP) and mineral separation plant (MSP) flow sheets were designed based on historical testing information and recent SII test campaigns on various composite feed samples. The flow sheets were finalized through rigorous process and orebody sequence modeling.The process uses traditional physical separation equipment; however a new MT spiral, the MG12, was selected for use on board the WCP for roughing duty. The MG12 spiral is a two-stage, twelve-turn spiral that has been proven to achieve very high recoveries of heavy minerals. The floating plant includes feed desliming operations, a central MT surge bin for optimum spiral circuit feed control and ancillary operations for concentrate and tailings handling. Scrubbed heavy mineral concentrate (HMC) is then transported to the MSP for concentration of the titanium and zirconium bearing mineral fractions.The testing, flowsheet development, and plant design will be described and explained, and a brief summary of the current project status will be given.IntroductionSouthern Ionics Inc. (SII) is a privately held chemical manufacturing company, founded in 1980 by Milton Sundbeck. SII focuses primarily on the sale of specialty and intermediate inorganic chemicals. Core markets include cement and refinery catalysts, molecular sieves, zeolites, pulp and paper, pharmaceuticals, TiO2 and water treatment. SII is built on the four cornerstones of service, quality, technology and delivery with all SII facilities ISO certified and key products used in potable water treatment certified to NSF standards. SII owns and operates its own transportation fleet and is focused on being a low cost producer, committed to safety and the environment."

Jan 1, 2015

By A. Mosqueda Martinez, L. C. Trytten, R. P. Kofluk, J. J. Budac

The Corefco ammonia leach nickel refinery treats Ni-Co mixed sulphides from the high-pressure acid leaching of Moa Bay nickel laterite. Due to the low iron content of the feed, the ammonia leach process generates a leach residue with ~10% Ni+Co. Since commissioning a leach residue pressure filtration circuit in 2002, this residue has been stockpiled, dried, and sold commercially. For several years, the residue was sold to nickel smelters overseas. In 2014, re-processing of the residue in the high-pressure acid leach was tested. Lab test work was completed showing excellent extraction of the contained nickel and cobalt, and additional beneficial effects in the high-pressure acid leach circuit. A plant test in Moa confirmed the results, and preparation for shipment of the valuable leach residue for re-processing has begun. This paper outlines the test work and results, and some commercial considerations.

Jan 1, 2015

By Zhan-fang Cao, Hong Zhong, Li-feng Li, Shuai Wang, Xiao-yu Cao, Guang-yi Liu, Ming-ming Wang

"In recent years, there has been an increasing focus on the hydrometallurgical processing of molybdenite, with the decline of high-grade and easily handled molybdenum minerals. In this work, a novel method of selective extraction of complex molybdenite concentrate, which is characteristic of high-grade copper ore, has been investigated. The results show that the leaching of chalcopyrite was impacted by the pH of the electrolyte when sodium carbonate and ammonium acid carbonate were added to the electrolyte. The leaching rate of molybdenum reached 99.39%, but chalcopyrite could not be leached at all in 240 min under experimental conditions of liquid-to-solid ratio 25:1, concentration of NaCl 4 mol/L, pH=9, room temperature and agitation speed 400 rpm. The grade of copper in the residue was 21.84%, with a recovery 99.93%. The technology of selective electro-oxidation leaching of molybdenum and recovery of copper from complex molybdenite concentrate is an effective separation method. The diffusion control model can be used to describe the process of leaching of molybdenum. The activation energy of the leaching reaction was found to be approximately 9.21 kJ/mol.IntroductionWorldwide, high-grade and easy-to-handle ore is decreasing, while the proportion of low-grade and complex ore is increasing. Porphyry copper ores with associated low-grade molybdenite are very abundant in China. Molybdenum is a valuable byproduct in the processing of porphyry copper deposits where the molybdenum is present in low quantities in the form of molybdenite (MoS2). In the conventional processing of copper sulfide ores by froth flotation, most of the molybdenite in the ore floats along with the copper sulfides. In this way, a bulk copper-molybdenum concentrate is produced. Afterward, the bulk coppermolybdenum concentrate is treated by differential flotation to obtain a rougher molybdenum concentrate, which requires several successive cleaning steps to produce a final molybdenum concentrate. However, it is widely recognized that flotation alone cannot economically produce a high-grade molybdenite concentrate, i.e., with less than 0.5% Cu. Therefore, in most cases, it is necessary to use a final step of chemical purification of the molybdenite concentrate to reduce the copper content to a level suitable for the market (Antonijevic and Pacovic,1992; Gerhardt et al., 2001; Fu and Zhong, 2003; Reza et al., 2006, Rafael et al., 2013)."

Jan 1, 2015

By Eurípides do Amaral Vargas Jr., J. A. de Mello Franco

"It is frequently necessary to excavate a tunnel for Civil Engineering purposes, or wells for petroleum exploitation, in laminated rock mass like schists or phyllites or in highly foliated gneisses. The determination of the pre-existing in situ stresses is essential, in order to assure the stability of these excavations. In most cases, the pre-existing triaxial stress field is arbitrary in relation to the tunnel or well axis. For these rock masses the concept of Generalised Plane Strain can be correctly utilized.There are closed form solutions for the calculation of stresses in anisotropic rock masses under Generalised Plane Strain conditions (Lehknitskii, 1981 and Hong , 1994). Based on these analytical solutions, established for the cases of Generalised Plane Strain, a synthetic problem will be formulated: the theoretical in situ stress tensor acting on this rock mass will be determined, with the aid of Bayesian Inverse Problem Techniques, as developed by de Mello Franco (2009). Additionally, the reliability of results obtained will be evaluated, in accordance with the research performed by this author. INTRODUCTIONThe Inverse Problem Technique, as developed in the paper, is based on the definitions and concepts obtained from the current literature and used for the solution of Inverse Problems, but the innovation to be presented is the utilisation of Bayesian Techniques and the determination of the reliability of the results obtained. This will be shown in a synthetic example where the determination of the in situ stress tensor, from strain measurements in a drill hole is supposedly performed. It is assumed that this drill has its axis arbitrarily placed in relation to the rock mass. Generalised Plane Strain conditions will hold for use with problem. The equations of Beltrami – Mitchel, in agreement to Lekhnitskii (1981) and Ong (1994), will be used in this synthetic case, for calculating strains, hypothetically measured in the hole before the final excavations. Finally a synthetic example for the determination of the in situ stress in a fully anisotropic rock mass, based on Bayesian Techniques and its reliability, developed in de Mello Franco (2009) is presented."

Jan 1, 2015

By Antonius Prayoga

PT Smelting adopted the Mitsubishi Continuous Technology for its copper smelter plant which has been operating since 1998. Through a series of expansion projects, the plant annual production capacity increased gradually from 200,000 to 300,000 tons of copper. There were no significant modifications for the smelter to reach the 50% additional capacity. It was mostly achieved by intensifying the operation of the furnaces by increasing the oxygen content in the furnaces blowing air. Intensive smelting furnace operation caused shorter campaign life of some furnace refractory, especially the melt zone wall on furnace outlet. During each furnace relining, which is done once every two years, severe wall erosion was found. The worst condition occurred in 2007 when the smelting furnace experienced a melt leak through the eroded wall beneath the bath-line coolers. During the 2008 furnace relining, a modification was performed by installing vertical coolers behind the melt zone wall. Additional vertical coolers were installed during the 2012 furnace relining to extend the coverage area. The modification improved melt zone wall integrity significantly by keeping them safely within the two year campaign life. Recently a modeling study was done to estimate the influences of molten waves on furnace wall erosion. The aim of the study was to predict the impact of blowing parameters, such as blowing air velocity, on the melt wave character and wall erosion.

Jan 1, 2015

By S. Devereaux, P. Gover, S. Everett

Having real-time data of blast furnace burden profile with respect to burden height and temperature is critical to making informed decisions on blast furnace operation. Given the high temperature and gaseous environment within the blast furnace shaft, traditional instrumentation has been limited at providing the level of real-time feedback information needed to optimize blast furnace operations. Infrared thermal imagery technology provides non-contact temperature measurement across the entire burden profile, allowing for better understanding of the dynamic movement of the burden within the blast furnace shaft. This technology increases blast furnace performance by improving the decision-making process for hour by hour operations. This paper will discuss the development of incorporating infrared thermal imagery technology into the operating strategy of a lead blast furnace.

Jan 1, 2015

By M. A. Halim, V. I. Lakshmanan, Z. Jankovic

An innovative mixed-chloride process for the separation of iron from lateritic ore is described. The separation of Fe(III) from leach liquor is an important process step for the recovery of nickel and cobalt. The patented process of Process Research ORTECH Inc. uses a lixiviant containing hydrochloric acid (HCl) and magnesium chloride (MgCl2) for the leaching of lateritic ores/concentrates followed by the selective solvent extraction step of Fe(III) over other value metals such as Ni and Co. The use of MgCl2 increases the activity of the hydrogen ion in the lixiviant, which reduces the consumption of HCl in the leaching stage and enhances the formation of HFeCl4-, thereby increasing the solvent extraction efficiency of Fe(III) with ketone. The process produces high purity iron oxide (Fe2O3) and regenerates HCl by the pyrohydrolysis of the FeCl3 rich pregnant strip solution. The developed process flowsheet is in closed loop, economically attractive and environmentally friendly.

Jan 1, 2015

By F. Bruey, T. Bruce, D. R. Nagaraj, W. Thomas, P. Riccio, E. Guitard

"AEROPHINE® 3418A Promoter is a flotation collector that has been an industry standard in the Canadian mineral processing industry since its first commercial use at the Kidd Creek concentrator in 1980. Its wide range of applications in sulphide mineral flotation has made it successful, specifically in the processing of complex sulphide ores which contain copper, lead, zinc, and silver or any combination of these elements for selective separation.AEROPHINE® 3418A Promoter is a unique, phosphine-based collector originally developed for the flotation of copper sulphide minerals and activated zinc minerals. It is now recognized for its selectivity for complex, polymetallic sulphide ores and porphyry copper ores. In addition, AEROPHINE® 3418A Promoter is highly selective for copper, lead, activated zinc, nickel and precious metals. AEROPHINE® 3418A Promoter exhibits strength yet, selectivity against iron sulphides (pyrite, pyrrhotite, marcasite, and arsenopyrite), non-activated sphalerite, and many minerals which contain penalty elements.This paper outlines a brief history of the product’s development, its historical use in Canada and several potential innovative mineral processing applications with the use of the chemistry. Three Canadian case studies will be presented on various ore types including: a Cu-Au ore, a Cu-Zn ore, and Cu-Pb-Zn ore. A plant production update will also be given on the future supply of AEROPHINE® 3418A Promoter.INTRODUCTIONCytec Industries Inc. operates a phosphine derivatives plant in Niagara Falls, Ontario, that manufactures various products for their speciality chemicals division. The products from this site are based on phosphine (PH3) chemistry and are used in a variety of markets including electronics, agriculture, LED lighting, water treatment, metal extraction, and mineral processing. One of the major products is the phosphine-based sulphide mineral collector, AEROPHINE® 3418A Promoter.AEROPHINE® 3418A Promoter (Figure 1) was originally developed for the flotation of copper and activated zinc minerals (Thomas, 2010).."

Jan 1, 2015

By F. D. Ford, Z. Dai, A. Byers

Manitoba Mining and Milling operations consist of three underground mines (Thompson T1, T3 and Birchtree), feeding the Thompson Mill. Three years ago, a collaborative effort involving Mines Exploration, Mines Project Development Group, Mill Technical Services and Vale Base Metals Technical Excellence Center was initiated to establish and verify the cause of high variability in concentrate quality and Ni recovery at the Thompson Mill. One outcome of this work was a program to systematically characterize the mineralogy and metallurgical performance of current and future orebodies feeding the mill. Mineralogy results show that high value enabling ores typically have a high pentlandite to pyrrhotite ratio and benign silicate mineralogy (mostly quartz and feldspar from sedimentary host rocks), while metallurgically challenging ores contain some combination of pyrite and/or hexagonal (non-magnetic) pyrrhotite and/or elevated quantities of talc (with associated carbonates) derived from altered ultramafic host rocks. The metallurgical performance of these two ore types has been simulated by an Excel particle flotation model, which calculates the relative floatability of particles based on the particle’s mineral composition and mineral locking determined from MLA images. The relationship between these mineral properties measured by MLA and metallurgical performance was established using 13 monthly composite samples from Thompson Mill. The model was then validated with results of laboratory flotation experiments on individual orebodies submitted for evaluation. The validated model can be used to predict plant metallurgical performance based on individual ore bodies feeding the mill. Individual orebody’s grade-recovery curves are assumed to be additive, and can be weighted in proportion to the mill feed to predict mill recovery over the same time period. The ore mixing can be done with a simple Excel spreadsheet and comes with a graphical output for easy visualization of the resulting grade-recovery curve.

Jan 1, 2015

By Brent A. Slaker, Michael Murphy, John Ellenberger, Erik Westman

"Photogrammetry, as a tool for monitoring underground mine deformation, is an alternative to traditional point measurement devices, and may be capable of accurate measurements in situations where technologies such as laser scanning are unsuited, undesired or cost-prohibitive. An underground limestone mine in Ohio is used as a test case for monitoring of structurally unstable pillars. Seven pillars were photographed during four visits over a 63- day period. Using photogrammetry, point clouds of the mine geometry were obtained and triangulated surfaces were generated to determine volumes of change over time. Pillar spalling in the range of 0.29–4.03 m3 of rock on individual rib faces was detected. Isolated incidents of rock expansion prior to failure, and the isolated failure of a weak shale band, were also observed. Much of the pillars remained unchanged during the monitoring period, which is indicative of proper alignment in the triangulated surfaces. The photographs of some ribs were of either too poor quality or had insufficient overlap, and were not included. However, photogrammetry was successfully applied to multiple ribs in quantifying the pillar geometry change over time.IntroductionAdequately measuring underground rock mass movements is integral to understanding how rock masses behave and how to interact with them safely and efficiently. Many modern measurement techniques employed in underground mining environments rely on point measurements, such as through extensometers or borehole relief methods (Christiansson, 2006). These techniques, while commonplace, do not provide a comprehensive view of how the rock mass is behaving. The dynamic changes in stress states underground, coupled with the mechanical uncertainty of rock masses, near active excavations, creates a need for measurement systems which better capture the behavior of the rock mass. Photogrammetry is a technology capable of producing the wide-area displacement measurements required for a comprehensive understanding of rock mass movements.Digital photogrammetry is a means of obtaining threedimensional point clouds from digital photographs. By finding the same point across multiple images, all viewing an object from different angles, the location of that point in three-dimensional space can be inferred. Close range digital photogrammetry (CRDP) is photogrammetry applied to measuring objects or scenes less than 100 meters away (Atkinson, 1996), and is used for various functions in underground mining environments. These uses include, but are not limited to, mapping fracture networks (Kim, Kim, & Won, 2005)(Somervuori & Lamberg, 2010), characterizing fractures (Styles et al., 2010) and measuring volumes of blast rock (Heal, Hudyma, & Potvin, 2004)."

Jan 1, 2015