Search Documents

By S. K. Kawatra, J. A. Halt

"Low-grade iron ores are finely ground and processed to recover iron-bearing minerals. However, the iron-rich powder is too fine to be used directly in blast furnaces and most direct reduction furnaces, and must be agglomerated or pelletized into a usable product called “pellets.” Bentonite clay has traditionally been used as a binder to make iron ore concentrate pellets, but it is expensive and contaminates the pellets. Organic binders may be a viable alternative to bentonite clay. This manuscript reviews organic materials that have been used to make iron ore concentrate pellets. Included are discussions on the development of organic binders, common pros and cons to organic binder use, organic binder structure and its effects on agglomeration, and additives to organic binders.IntroductionIron ore agglomeration turns finely disseminated, low-grade iron ores into a usable product, called pellets. During pellet production, fine-grained, iron-rich minerals are liberated from low-grade ores, concentrated, and agglomerated into round balls that are thermally hardened or cold-bonded to form pellets. Pellets are then transported to blast furnaces or direct reduction operations where they are used to produce iron; iron is further refined and shaped into the wide variety of steel-based industrial and consumer products in use today.Over the years, pellet production has become increasingly more prevalent with the increased exploitation of low-grade iron ores and increased iron and steel consumption around the world. In 2010, world iron ore pellet production was 388 Mt. It could be argued that the current pellet production process has been enabled by the use of binders – practical experience has shown that it would be nearly impossible to agglomerate iron ore concentrates using rotary drums and discs without using a binder."

Jan 1, 2015

By N. Erarslan, M. Ghamgosar

The size of rock fragments depends on the nature of the loading applied the strength of the minerals and the texture of the rock. Research in the literature demonstrates that there is a distinct difference in the rock fracturing process for static and cyclic loading. The tensile strength of brittle rocks is also one of the most significant parameters influencing the rock fracturing process and the propagation of micro-fractures on the crushing, blasting and cutting of rock. The Brazilian indirect tensile test, one of the methods approved by the International Society for Rock Mechanics (ISRM), has been used to determine rock fracture behaviour under different cyclic loading modes. In this study, the dimensions of Brisbane Tuff specimens have been selected according to the method outlined by the ISRM. The main aim of this study is to evaluate the effect of cyclic loading amplitude and frequency on the Fracture Process Zone (FPZ) at the micro-, meso- and macro-scales. The post-failure behaviour of the Brisbane Tuff specimens was obtained under cyclic loading with frequencies varied from 1 to 10 Hz. The amplitude was varied from 10% of Ultimate Tensile Strength (UTS) up to 80% UTS. Laboratory investigations of rock fragment size revealed that different loading frequencies and amplitudes produce different FPZ dimensions. Multivariate Analysis of Variance (MANOVA) results demonstrated that the FPZ dimension is relatively sensitive to the frequency change. Fragment size analysis showed that the FPZ is a consequence of the initiation, propagation and coalescence of micro-fractures and depends on the nature of the loading. Laboratory evidence showed that the FPZ dimension, for the cyclic tests performed on Brisbane tuff, is ranged from 0.07 to 20 mm. The achievement of this study highlights a key finding in the understanding of fracture patterns and propagation models in the FPZ under cyclic loading, which is the dominate mechanical action in the oscillator disc cutter (ODC).

Jan 1, 2015

By Dinesh Hinduja, Pérez: Miguel

"Large structures are generally exposed to dynamic and structural loading. They require usually either foundation connected to hard rock through sockets or driven foundations, which encounter boulders as well.In this regards drilling hard-rock sockets or boulder offshore or onshore can be a challenging job especially when deep foundations are mandatory. To overcome the challenge, specialized equipment like a Pile Top Drilling rig (PBAs) can be used, which have to be correctly set-up and operated in order to get its maximum drilling performance. High performance drilling with PBAs requires maximizing key elements of its operation. The configuration and management of the drill string components are important. The key elements are constant weight on bit which is done by adjusting ballast and managing thrust force; and selection of cutters and proper flowing discharge.The methodology is based on the experience from over 40 years of building and operating PBAs for different project applications. These applications include drilling offshore and onshore for:?Superstructures and buildings?Drilling platforms, barges and jack-ups?Harbours, jetties, dry docks and dolphins?Bridges, piers and causeways?Marine sewerage diffusers?Offshore wind farms?Dam rehabilitationMHWirth documented methodologies demonstrate that by using PBAs properly it is possible to improves performance of underwater drilling for hard-rock sockets and boulders which ultimately reduces project-cost.Background. There is a significant percentage of total project cost in structural foundations. Equipment capabilities and technics to drill shaft with rock-sockets and embedded boulders onshore and offshore are highly developed due to the dramatic equipment advancement and experience in the last 40 years. Formerly, driven piles accounted for the majority of foundations either onshore or offshore, following the experience of previous practice in the market. Nowadays, deep drilled foundations can be constructed to carry the load through the overburden down to the sound load carrying rock or soil.Scope and objectives. The overall objectives of this study are:?Synthesis information on current practices to drill shaft with rock-socket and/or embedded boulders onshore and offshore with Pile Top Drill Rigs?Identify the principal challenges evolving with practice?Provide suggestions for improvements in the construction of drilled shafts through proper operation of Pile Top Drill Rigs?Convey information through case studies and experiences"

Jan 1, 2015

By J R. Barber, B. E. Rogers, R. Fukuzawa

Mercury is sometimes present in non-ferrous ores including gold, zinc, copper and lead. The selection and use of appropriate mercury abatement technology is critical for preventing its release to the environment during ore processing and to protect workers from mercury exposure. This paper presents a general decision-making process for mercury abatement technology selection for major emission sources in the gold industry. Mercury abatement can be accomplished through making process changes and/or by adding a process step to an existing system (i.e. "end-of-pipe control"). Advantages and limitations of the technologies along with waste / by-product management options are discussed through case studies of current operating mercury abatement systems.

Jan 1, 2015

By Xiong Tong, Jiushuai Deng, Yingbo Mao, Lingyun Huang

Ammonium carbamate has been used as a reagent for the leaching of copper from the copper oxide ore found in the Honghe state, Yunnan province, China. In order to find the optimal conditions for the leaching of copper from this copper oxide ore,the effects of several processing parameters, including the concentration, time, temperature, particle size and stirring intensity have been investigated. The results of these optimization experiments showed that the leaching rate of copper reached up to 72.76% under the following conditions: liquid-to-solid ratio of 10:1, ammonium carbamate concentration of 2.5mol/L, leaching temperature of 45 °C, stirring speed of 300rpm, a reaction time of 1.5 h and 85% by weight thereof passes through a sieve having 0.074 mm.

Jan 1, 2015

"History - How did you get into mining and involved with SME?Unlike many past presidents, I do not come from a mining lineage. I liked math in high school and believed I wanted to be an engineer. I told my math teacher that, and he laughed in my face. I believe that humiliation is what carried me through engineering school. At the time my ability to go to college relied on how inexpensive I could make it. My brother told me that there were a lot of scholarships in mining engineering, and I should apply to mining schools. As usual, he was right and I was off to the University of Idaho to study. My first summer break I got a job with Hecla at a mine in Arizona. I was a laborer on a shotcrete crew. I knew after the first summer that I loved underground mining, and I never considered changing disciplines. Looking back, I was working in miserable conditions (hot, humid), on a miserable job (shotcrete), where I got injured, and two summer student roommates died in a car accident on the commute home after work. I had every reason to hate the industry, as I had seen virtually everything bad about what we do. But I didn’t, I loved it. I said I was good at math, I never said I was smart.I joined SME in college because I was told to by the head of the mining school, Dr. Jack Hoskins. You did what Jack told you to do. I got involved because I went to an annual meeting and the papers in the underground sessions were terrible. I refer to bad papers as the “Tensile strength on cable bolts in sub-arctic regions on Tuesday” papers. Real snoring fodder. I don’t remember who I was complaining to, but they told me to quit my grumbling and fix it. So I chaired a session, and tried to get only good quality papers, something that has been my mantra for years with the Mining & Exploration Division. I also volunteered to help the local sections too. Then one day I woke up as president.What is your opinion of the health of the mining industry?The mining industry is in bad shape. Coal is under attack and will likely never recover to its former greatness. Our President has banned new coal leases, and the state of California is forcing people it does business with to divest their interests in coal companies. And that all happened in just in a few short weeks this January. Usually in America you get a trial before you are given a death sentence, but not with coal."

Jan 1, 2015

By F. Baczek, S. S. Rocks, D. Chaiko, T. Walters

The atmospheric leaching of chalcopyrite concentrates using acidic ferric sulfate lixiviants is well known to suffer from slow leach kinetics and poor copper recoveries. A number of approaches have been proposed for improving both leach kinetics and recoveries in this system. Many of these, while effective, suffer from high CAPEX and/or OPEX. As many mine sites begin transitioning from heap leaching of copper oxides to processing of primary copper sulfides, cost-efficient leach processes that are compatible with existing SX/EW processes will be needed to maintain existing cathode production. To this end, FLSmidth is exploring process options and reactor technology for the hydrometallurgical processing of primary sulfides. One approach that appears to be highly effective at increasing copper recoveries takes advantage of the enhanced reactivity of transitory, surface-defect structures generated during particle fracture. Significant process efficiencies are gained by matching the rate of grinding to the rate of electrochemical leaching in Mechano-Chemical leach processes. The patent-pending FLSmidth® ROL process uses a Stirred Media Reactor (SMRt reactor) to achieve copper recoveries of 97+% in 6 hours or less. This approach overcomes many of the surface passivation problems that have hindered other atmospheric leach processes. New insights to leach mechanisms are presented.

Jan 1, 2015

By X. S. Fan, T. R. Feng, D. Chen

To meet the flotation process requirements, the large-scale flotation cell must be designed for sufficient pulp mixing, reasonable air dispersion and solid suspension, which is very difficult to design for super large-scale flotation cell. Hence, the flotation cell scale-up and optimization for a short period is a challenge for super large-scale flotation cell design. Computational fluid dynamics simulation has been applied in flotation cell study, which is effective, timesaving and low cost in the study of the flow field distribution for super large-scale flotation cell. This paper demonstrates the flow field characteristics in the 600m3 flotation cell by CFD. The flotation cell model is meshed with hexahedral grid and the high mesh quality assures the computational precision. MRF model, namely a steady-state approximation, ensures that individual cell zones can be assigned different rotational speed. Euler-Euler approach is chosen for multiphase flow simulation to treat different phases as interpenetrating continua. Numerical simulation of single phase, two-phase and three-phase are investigated respectively. Results suggested that the flotation cell has the apparent upper and lower flow circulation. In condition of the impeller rotation, the air is dispersed reasonably. In addition, the solid phase volume concentration distribution in the cell has a little difference.

Jan 1, 2015

By J. L. Feng, F. Zhang, S. K. Hu

"Cracking is one of the most serious damages in tunnel linings, which is often observed by in-situ inspection to tunnel engineering. It is difficult to better characterise for the deformations from continua to discontinua by the traditional continuum mechanics due to emerging of crack initiation, crack propagation, and coalescence, at several scales. In this paper, the process of failure that was from micro damage to macro crack in concrete tunnel linings under experimental load conditions, was quantitatively simulated by the combined finite-discrete element method (FDEM). Comparison of the simulating results with that obtained by the full-scale test of concrete lining under different loading conditions in the literature was respectively good agreed and shows that such FDEM technique is appropriate to model the continuousdiscontinuous problems. The present study indicates that the FDEM technique could be benefit to quantitatively evaluate the stability and damage level of tunnel lining system. INTRODUCTIONMost damage to tunnel linings is caused during the construction phase, which can emerge in a form of single macro cracks or even large-scale spalling. The cause of such damage is mostly the occurrence of, either impermissibly large contact stresses resulting from high thrust loads combined with production and installation tolerances in the segments resulting in a geometrical lack of fit (Maidl et al., 2012; Transportation Research Board, Basic Research and Emerging Technologies Related to Concrete Committee, 2006), or unallowable tensile/shear stresses appearing in the tunnel linings under complicated loading conditions (Ansell, 2010). Such a macro failure phenomenon may also be regarded to as a result of growth, coalescence, initiation of microcracks in tunnel linings due to the complicated loading action, and even potentially lead to an instability or collapse of the local or entire tunnel system. Much work has been devoted to investigate for the characters of micro and macro cracks, the influence factors of damage patterns, the settlement of a tunnel, the width, length and density of lining cracks, especially from classifiedly and qualitatively (Wang, 2010; Huang et al., 2013). However, the safety evaluation of tunnel is definitely required to not only inspect in situ, but further also quantify computing and analyzing for tunnel lining systems, so as to provide a global viewpoint of process of the tunnel deformation, which aims to help for subsequent decisions, e.g. controlling traffic flow or immediately repairing task. Additionally, the design of lining thickness and its structural analysis that is mostly determined by previous experience and similar construction examples is also needed to be improved."

Jan 1, 2015

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By F. Baczek, S. S. Rocks, D. Chaiko, C. Eyzaguirre, S. Asihene, T. Walters

The majority of efforts to improve primary copper sulfide leaching have focused on solution chemistry, temperature, O2 pressure, ultra-fine grinding, the use of catalysts, etc. Historically, very few studies have focused on the solid/solution interface. A new, patent pending approach to catalyzed, copper sulfide leaching has been discovered by FLSmidth that enables manipulation of the 2-D semi-conductor properties of chalcopyrite surfaces to the benefit of higher electrochemical reactivity. Copper dissolution rates are then further accelerated by incorporating a Stirred Media Reactor (SMRt) into the process. By using minute amounts of Cu2+ to "pre-activate" chalcopyrite, leach times have been reduced from >20 hours with incomplete Cu dissolution to <2 hours with 98+% Cu dissolution at 80°C. The pre-activation process takes only minutes to complete at temperatures of 80°C or less. The total atmospheric leaching process, incorporating the pre-activation and Stirred Media Reactor is compatible with existing SX/EW processes. Results of batch leach testing are presented and possible mechanisms are discussed.

Jan 1, 2015

By H. Tsuruta, A. Fujibayashi, I. Sumi, A. Murao, R. Murai

Injection of biomass into blast furnace as alternative reducing agent is so effective for the purpose of mitigation of carbon dioxide emissions from steel industries, because biomass is considered to be carbon neutral raw materials. Certain amount of Palm Kernel Shell (PKS) is abandoned after Palm oil extraction process. To use as a reducing agent of blast furnace, PKS was carbonized and classified by 100 mesh sieve. To examine the gasification behavior of PKS carbide under the blast furnace conditions, several combustion experiments were conducted using hot model experimental furnace. The experimental results showed that the gasification efficiency of PKS carbide increased as the quantity of volatile matter increased. This tendency is the almost the same for the pulverized coal, so carbide of PKS can be used at blast furnace at appropriate amount of volatile matter that can be controlled by carbonization condition. In addition, the pressure drop of the furnace tends to decrease because the amount of ash in PKS carbide may be smaller than that of pulverized coal. PKS carbide is a suitable reducing agent in that respect.

Jan 1, 2015

By Chris Twigge-Molecey

"Over the last 50 years there has been a dramatic evolution in the metallurgical engineering field in Canada. In the 60s the field was dominated by large American and UK groups, often selling major process and equipment packages. The local content was limited to wrap around facilities and the civil and structural work. The mining and metallurgical companies had strong internal teams to lead these projects. Over the decades and business down cycles the large foreign contractors disappeared or re-structured and the mining companies largely shed their engineering and project management groups. The resulting gap was filled by a cadre of local specialist engineering companies, some of whom have grown to be world leaders in the field. The paper traces this evolution and examines the underlying causes and consequences."

Jan 1, 2015

By E. Ghali

"Corrosion of support system components (e.g., bolts, mesh, plates) is a safety and economic concern in underground mines. This paper reports the results of a five-year study wherein corrosion coupons were installed at select locations in participating mines, recovered at regular intervals, analyzed for signs of corrosion, and tested to quantify loss in capacity. Complementary tests were conducted on recovered mesh and friction bolt specimens. The data provide insights into contributing factors for support systems corrosion, which aid in the selection of appropriate support strategies and reliable assessment of the useful life and need for rehabilitation of a support system.RÉSUMÉ La corrosion des composantes des systèmes de soutien (p. ex. boulons, grillages et plaques) est une préoccupation économique et de sécurité dans les mines souterraines. Cet article présente les résultats d’une étude de cinq ans pendant laquelle des coupons de corrosion ont été installés à des endroits spécifiques dans les mines participantes; ces coupons ont été retirés à des intervalles réguliers, analysés pour des signes de corrosion et mis à l’épreuve pour quantifier la perte de capacité. Des essais complémentaires ont été effectués sur les grillages récupérés et sur les échantillons de boulons d’ancrage. Les données aident à comprendre les facteurs qui contribuent à la corrosion des systèmes de soutien, ce qui est utile dans le choix de stratégies appropriées de soutien et pour une évaluation fiable de la durée de vie utile et du besoin de remise en état d’un système de soutien."

Jan 1, 2015

By T. Shumka, M. J. Druckenmiller

"INTRODUCTION As we push further into the 21st century and closer to a more efficient mine, safety and operational enhancements are the two major keys towards attaining success. The Crusher Vision Automation System (CVAS) is a technological advance that will allow an operator to achieve higher safety and higher operational goals in the same piece of equipment. The CVAS is a patent pending system and method for measuring and maintaining the closed side setting (CSS) on gyratory crushers. In the same equipment and technology package, the CVAS will also allow safer placement of main shaft pieces for maintenance and replacement. This technology yields multiple uses and allows a site to significantly enhance safety and operational efficiencies. This measurement technique is used to provide more accurate data and faster data collection times than current techniques used today. It will give crusher operators accurate and reliable measurement for the CSS in a live, operating environment. Measurement data can be collected in five minutes allowing for fast adjustment of the mantle position and subsequent enhancement and streamlining of a crusher and downstream flowsheet. The advantage of this system is that it is permanently mounted at the crusher location, where the operator can turn the system on and off as many times as they like throughout the day with a goal of maintaining a constant CSS gap based on production and maintenance criteria to help streamline operations and enhance safety efficiencies.Regarding its other main functional area, mainshaft maintenance, it allows this work to be performed remotely while keeping personnel safer and out of harm’s way. SAFETY ENHANCEMENT The safety factor enhancement with this system is extreme. It does not require the use of overhead cranes, cleaning out the crusher, lowering people into the crusher or having the operator lower paint cans or lead balls into the crusher pocket while the crusher is in operation for measuring the setting. In order to perform the CSS measurements, the operator only needs to operate the laser through manipulation of a joystick while watching the video feed. Danger of a person falling into the crusher while trying to take measures is eliminated, as are the effects of handling lead balls and tracer dyes."

Jan 1, 2015

By B. Yu, S. Kelebek, C. Gibson, M. Aghamirian

There are a number of high grade niobium deposits worldwide which have been deemed untreatable by flotation due to the very fine grained nature of the in situ pyrochlore, the primary niobium bearing mineral. A known method of recovering extremely fine particles is through the use of chelating reagents such as hydroxamic acids which have a strong affinity for transition metals. However, one of the major issues in the flotation of niobium bearing minerals using hydroxamic acids is the corresponding recovery of other transition metal gangue minerals including magnetite, hematite, and pyrite. In order to better understand the differences in behavior of niobium and iron bearing minerals in flotation with benzohydroxamic acid (BHA) and sodium hexametaphosphate (SHMP) at a range of pulp temperatures, a Box-Behnken experimental design was employed. Regression models for the global recovery of iron indicated that iron mineral recovery was significantly influenced by both BHA and SHMP dosage. Upon examinination of flotation products by semi-quantitative XRD, it was observed that recovery of iron oxide and sulphide minerals (hematite, magnetite, goethite, and pyrite) was problematic at high benzohydroxamic acid dosage, while sodium hexametaphosphate was mainly helpful for carbonate mineral depression. Iron rich carbonates (likely an iron rich dolomite) largely reported to the tails with increased SHMP dosage.

Jan 1, 2015

By M. Abdellatif

"SynopsisCalcined basic nickel carbonate (BNC) concentrate was smelted in a pilotscale DC arc furnace to produce a nickel metal. The furnace was continuously operated for 12 days (24 hour/day), during which twelve different smelting conditions were investigated, with the major variables being reductant type and feed rate, flux composition and addition, and BNC feed rate.The 200 kW DC arc furnace was operated at power levels between 110 and 165 kW and at a total feed rate of 78 to 96 kg/h, resulting in an average slag and metal tapping temperature of about 1650°C. A total of 7.2 t of BNC were smelted, producing about 5.44 t of nickel metal and 2.94 t of slag. Nickel recoveries of 96.4% and higher were achieved, and the slag nickel content was as low as 0.1%. The major impurities in the metal were iron (mostly from oxygen lancing) and carbon. The calculated feed carry-over was less than 0.85% and the graphite electrode consumption was between 2.8–3.3 kg/MWh.IntroductionOne of the most distinctive advantages of DC open-arc smelting is the ability to process fine raw materials without any major issues with regard to the operability of the furnace, metal recovery, and metal quality. This has been demonstrated in Mintek’s DC arc pilot plant facilities over a period of about three decades (Curr et al., 1983). The materials that have been processed include laterite (Kotze, 2002), chromite fines (Curr et al., 1983), manganese fines (Lagendijk et al., 2010), PGM concentrates (Shaw et al., 2013), electric arc furnace (EAF) dust (Denton et al., 2005; Abdellatif, 2002a) and stainless steel (SS) dust (Denton et al., 2005; Abdellatif, 2002a; Goff and Denton, 2004), and petroleum fly ash (Abdellatif, 2002b). The top particle size of such materials can vary from a few millimetres (e.g. laterite) to micrometres (EAF and SS dust). Dusting, whether due to physical carryover of feed or to the arc side reactions, has been proven to be a non-issue. As such, the applications of DC open-arc furnaces have the potential to be extended to other raw materials such as particulate nickel oxide, which has a particle size much less than 100 µm.Nickel oxide is typically produced from laterite ore by sulphuric acid leaching, purification, and precipitation as basic nickel carbonate (BNC) (Rhamdhani, Jak, and Hayes, 2008) or as mixed hydroxide precipitate (MHP) (Mackenzie, Virnig, and Feather, 2006), and finally calcining at moderate temperatures (800–1200°C). The NiO product is very fine, with an average particle size in the range of 10–20 µm and a NiO content of more than 99%."

Jan 1, 2015

By B. H. Sadagah

"Construction of mountain roads at north westerly Saudi Arabia is a difficult task in rugged terrains, where the rock masses are steep slopes, and full of geomorphological constraints.Werka descent lies at the north west region of Saudi Arabia. The Werka descent, constructed four years ago harmed due to rainstorm. The rock masses are metabasalt and metaryolite tuff rocks. The road is eight m-wide, surround by unsupported sharp manmade slope cuts, reaches up to 15 to 40 m height on both sides. Failures took place at both sides of the road, and blocked it. The road of almost 2 km long subjected to all modes of slope instability such as rockfalls, manmade slope failures and debris flows in the absence of the remedial measures. The very precipitous 40 m-high rock slope-cut along the road has no benches, backed by a natural slope of almost 80 m height. Both types of slopes suffer from rockfalls and slope failure’s incidents, frequently took place mainly in rainy seasons. The steep manmade rock slope cut is less than 1 m close to the road, with no ditches, form a potentially source area for rockfall’s hazards.Intensive geotechnical study includes utilization of the RMR and GSI rock masses classifications indicates that the rocks are fair to poor quality. The DIPS, RocFall, Swedge, RocTopple, RocPlane computer program, in addition to GIS and DEM image utilized to perform modeling and deterministic analysis, in order to suggest the mitigation measures for the natural and manmade slope cuts and rockfalls. The seismic coefficients of 0.1 to 0.4 taken into consideration in modeling processes. Input parameters to model the rockfalls and slope failure’s characteristics were studied such as GSI, block size; seeder points, locations of fallen blocks; slope angle, restitution coefficients, and slope roughness. The programs modeled the proposed location, height and energy of the rockfall barriers, collectors, and rock bolts. Two manmade slope cuts studied and modeled utilizing the integrated techniques were to eliminate the risk of slope failures and rockfalls through the construction of remedial measures, this is the study objectives."

Jan 1, 2015

By X. -G. Chen, E. M. Elgallad

Direct chill (DC) cast ingot plates of 2xxx alloys have been increasingly used for large mold applications in the plastics and automotive industries. A novel heat treatment practice for Al-3%Cu-1%Mg DC cast ingot plates has been developed, involving solution treatment, furnace cooling to the desired aging temperature and holding for appropriate time at the aging temperature. The mechanical properties of the plates were studied for different combinations of aging temperature and time, using hardness measurements and tensile testing. The evolution of the strengthening precipitates was investigated under different cooling rates corresponding to cold water quenching, still-air cooling and furnace cooling, using electrical conductivity measurements. The results showed that by applying the novel heat treatment, the cast ingot plates could provide a wide range of combinations of strength and ductility satisfying the design specifications of large molds. This, in turn, offers a practical solution for the fabrication of extremely large DC cast plates combining between good mechanical properties and low levels of residual stress using the shortest possible heat treating cycle.

Jan 1, 2015

By T. R. Kostecki, J. Hirschi

"Analytical engineering design is based upon a trial-and-error iterative and deterministic process. Within this process, the engineer obtains some estimated values, plugs them into de facto closed-form equations, and receives output, which is expected to be a single number that serves as the basis for the design. This number is typically a factor of safety, or some other equivalent strength-stress ratio. This provides the engineer with a quick and relatively quantitative design methodology. This can create problems however, because in mining applications, the actual in situ system is highly variable, complex and often chaotic, which can lead to potentially incorrect conclusions that result in unsafe designs. A more appropriate and reliable approach is a probabilistic analysis for engineering design. This process is used widely in civil and other engineering disciplines, but is often overlooked for applications in coal mine design. Additionally, it seems the amount of past studies using this approach, especially in coal mine design, are rather limited. Considering how the probabilistic approach can account for uncertainty in parametric values and how unpredictable a mining design can be, the authors believe that this approach has potential in mining. This paper will focus on a summary of past studies related to probabilistic analysis in coal mine pillar design and provide recommendations for future work that could improve design reliability. INTRODUCTIONFeasibility and fundamental design procedures for excavations often start with an assessment of mine openings, pillar design, and the surrounding structure by using a deterministic approach with closedform solutions (ex. Bienawski, Obert-Duvall). These are reliable methods, but designers know that the inputs in these closed-form solutions are estimates at best and do not incorporate any degree of uncertainty. This is therefore not an optimal design procedure.A more appropriate design should incorporate some uncertainty because of the chaotic and variable nature of geology and mining conditions in general. In an attempt to account for uncertainty, a probabilistic approach can be adopted, which accounts for deviations in variables and provides a more optimum design solution. By applying a probabilistic approach, a designer can look at multiple failure scenarios at the same time instead of using the same deterministic design over and over."

Jan 1, 2015