Search Documents

By James M. Tantalla, Jr. Ellman

"Construction of the powerhouse for the Willow Island Hydroelectric Project, located at the Willow Island Lock and Dam, required a 120-ft deep temporary excavation inside the limits of a cellular cofferdam on the Ohio River side of the excavation and a soil-bentonite seepage cut-off wall on the landward side of the excavation. Stability analyses were performed for critical sections to evaluate the stability of the soil slopes and rock cuts using limit equilibrium, tension crack, and buckling analysis techniques. The stability analyses indicated adequate factors of safety through the landside embankment sections, and for the weighting berm soil slopes in front of the riverside cellular cofferdam. However, the results of deep-seated stability analyses through the rock supporting the riverside cellular cofferdam indicated marginal factors of safety for the 100-year flood condition. Consequently, the riverside portion of the excavation required enhanced stability measures, namely the installation of long, high-capacity rock anchors. Also, the dewatering system was modified to lower the site piezometric head to near the top of rock to improve the stability of the rock cuts.Thirty high-capacity rock anchors were installed on the upstream, riverside, and downstream sides of the cofferdam rock cut. The rock anchors consisted of multiple, seven-wire strands designed to provide the full-required design load at 60% of the strand capacity. Rock anchor loads varied from 1,968 to 2,074 kips. The maximum number of strands per anchor was 59. Bond lengths assumed an allowable bond stress of 100 psi based on the rock bond from pull-out tests.Project DescriptionAmerican Municipal Power, a nonprofit organization that owns and operates electric generation facilities for its member communities, has been in the process of constructing hydroelectric power plants adjacent to existing navigation locks and dams along the Ohio River. The Willow Island Hydroelectric Plant was recently completed on the West Virginia bank of the river adjacent to the US Army Corp of Engineers (USACE) Willow Island Lock and Dam. The plant is on the opposite river bank to the locks, and includes two turbine generating units with FERC rated capacity of 44MW at a 20-foot head differential. The Ruhlin Company of Sharon Center, Ohio was awarded contracts to construct both the cofferdam and the powerhouse. Construction began in mid-2011, and was completed in early 2016."

Jan 1, 2016

By K. K. Mamyrbayeva, G. Z. Guseinova, V. A. Luganov

This paper presents the results of theoretical and technological studies on leaching ore of Bozshakol deposit. The major oxidized copper mineral of Bozshakol ore is atacamite, and the content of malachite, azurite, cuprite, copper sulfide minerals is insignificant. The chemical composition of the test sample, with mass, %: 0.9 Cu; 55.00 SiO2; 22.40 AI2O3; 9.00 Fe2O3; 2.24 CaO; 3.56 MgO. Technological studies on leaching the ore were carried out with sulfuric acid 5, 15, 25 and 50 g/dm3 in one and multistage (up to 4 stages) countercurrents. Size of ore 1 mm, the ratio S : L 1: 4. It was found that with increasing of acid concentration from 5 to 50 at one-mode leaching the copper extraction reaches 55 %. At multistage leaching the copper recovery reaches 73 %, a productive solution containing g/dm3: Cu - 4; Fe – 1.2; Al – 1.1 at a pH of 2.8. When leaching the cinders obtained by ore roasting in an atmosphere with limited value of oxygen, with increasing of the roasting temperature from 650 up to 750 °? the extraction of copper from the Bozshakol ores reduced from 31.5% down to 24.4%. The rate of filtration is markedly increased compared with the crude ore. When leaching the cinders obtained by roasting in a nitrogen atmosphere a marked increase up to 87.2-88 % of copper extraction from Bozshakol ores is observed. As an extractant for the extraction of copper from the pregnant solution used LIX984N extractant in kerosene. On the basis of the calculations it was built extraction isotherm and modeled processes of copper recovery with the circuit 2E + 1P, allowing up to 93 and 96% extraction. The through extraction of copper from the ore in the electrolyte was 67 %. Technology is recommended for semi test.

Jan 1, 2016

By S. Kelebek, B. Ingram, C. Gibson, T. MacNeil, M. Aghamirian

"The beneficiation and upgrading of pyrochlore from its ores is carried out through flotation. In industrial practice, upgrading is conducted in a two-stage flotation process in which pyrochlore flotation is carried out after gangue mineral pre-flotation (carbonate, silicate, sulphide or phosphate reverse flotation). In this study, the flotation of pyrochlore from a low grade carbonatite ore was performed at the laboratory scale following a two-stage flotation process in which carbonate minerals were floated in advance of niobium minerals. In parallel, a simplified flotation process was developed in which pyrochlore was floated directly from gangue minerals at increasingly acidic pH. Laboratory results indicated that both two-stage and direct flotation provided similar results in terms of niobium grade-recovery. Based on these results, a large scale, integrated pilot plant was conducted using a direct flotation flowsheet. While the elimination of reverse gangue flotation resulted in flowsheet simplification, the dissolution of carbonate minerals and the subsequent effect of dissolved cations on the floatability of pyrochlore added an element of complexity. A comparison of results from locked-cycle laboratory testing and pilot plant testing highlights the challenges of scaling up a complex flowsheet. A case is made for the direct flotation process and the key parameters to achieving success in large scale direct flotation of pyrochlore are discussed.INTRODUCTIONPyrochlore (Ca,Na)2Nb2O6(OH,F) is a niobium bearing mineral which has been the primary global source of niobium since the first pyrochlore mine commenced operations in the late 1960s (Gibson et al., 2015a). Preceding the discovery and development of high grade pyrochlore deposits in North and South America, the majority of global niobium supply came from gravity concentration operations of columbite (Fe,Mn)Nb2O6, across Africa (Perrault and Manker, 1981)."

Jan 1, 2016

"Energy efficiency in mining and minerals processing has attracted considerable public and industry attention because of the significant quantities of energy consumption involved. In this context the question of what are worthwhile targets for energy efficiency improvements ought to be of the highest priority. It is however worth taking a step back to avoid falling in the trap of taking preconceived ideas that have been reiterated repeatedly before as gospel. The aim of this paper is to highlight areas where new or alternative approaches could potentially be the better way forward. Some may come as a surprise to conventional industry thinking. Ultimately any such solutions are attractive to practitioners not just in an environmental but also in an economic sense, and hence should be targeted through applied research and development efforts. This paper highlights key aspects of each group of opportunities and some of the individual approaches to provide an overview of the current status quo.MINING INDUSTRY POWER UTILISATION – WHERE IS THE BIGGEST BANG FOR THE BUCK?The question of where is the biggest bang for the buck when trying to determine worthwhile targets for energy efficiency improvements has not always been reported on broadly enough, typically because industry practitioners operate in specific areas of expertise and comfort zone. Looking beyond the familiar doesn’t always come easy. Any technology or methodology consideration to address energy efficiency needs to take into account the context of alternative opportunities of superior value or risks not achieving desired uptake. The following sub-chapters have been ordered by magnitude of improvement potential as best as is possible, starting with the biggest first, and the smallest last. Some may be a surprise relative to conventional mining industry thinking."

Jan 1, 2016

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

By S. Parent, J. -F. Lepage, S. Glover

"Goldcorp – Eleonore’s 7 000 tonnes per day gold mill was started up in October 2014 and achieved commercial production in April 2015. During the first year, operation has faced challenges from grinding, flotation, sulfide cyanidation and tailing filtration to achieve targeted throughput, availability and recovery.The optimization of non-sulfide tails filter cloth lifetime and filter press availability had the most significant impact on ramp-up of both mill throughput and availability. A change in steel ball addition size to the grinding circuit was made to meet the targeted p80 of 65 µm. Various optimization efforts were conducted on the flotation circuit, intended to recover all sulfide-bearing minerals. The goal is to attain the environmental target of 0.12% sulfur in flotation tails (to eliminate acid mine drainage or AMD), while an average of 0.31% sulfur was obtained over the first months of 2015. Collectors, frothers, activators and hydrodynamic parameters were tested to improve the circuit desulfurization efficiency. High sulfide reactivity in pre-oxidation and cyanidation severely impacted dissolved oxygen levels and cyanide consumption. Studies were undertaken to understand the effects of mineralogy, grind size and leach conditions on gold dissolution kinetics and cyanide consumption. Efforts were focused on pre-oxidation to restore dissolved oxygen levels as well as optimizing both lead nitrate addition and pre-oxidation time.INTRODUCTIONGoldcorp Eleonore’s mill commissioning started in September 2014. It was considered to operate the mill at 3 500 tpd during design, as the mine was planning to operate at this throughput for the first year. However, with the stockpile of ore and a higher throughput from the mine, the mill was able to run at higher tonnage than initially anticipated.While increasing tonnage, a few bottlenecks were discovered and overcome in areas such as filtration and cyanide destruction. There were also recovery issues which were addressed in areas such as grind and sulfide leach. This paper focusses on the first complete year of operation ending September 30th 2015. A process description and the flowsheet are presented below and it will then go into detail about operational, metallurgical, mechanical and design issues experienced during the year."

Jan 1, 2016

By K. E. Waters, E. R. L. Espiritu, G. R. da Silva

"Rare earth (RE) elements are essential components of emerging green technologies. The increase in demand for these applications have driven the search and development of new rare earth deposits such as the Niobec project in Quebec, Canada. This deposit consists primarily of dolomite with significant amount of RE minerals bastnäsite and monazite, the primary sources of RE elements. Due to the minerals’ fine liberation sizes, flotation is commonly used as a concentration method. To develop an efficient process, the electrokinetic properties of the minerals must be understood. In this study, the surface properties of bastnäsite, monazite (RE minerals) and dolomite (a common gangue mineral) were investigated by zeta potential measurements. These measurements are affected by various ions present in solution; for bastnäsite, monazite and dolomite, some of these ions are H+, OH-, PO43- and CO32-. Dolomite, being a sparingly soluble mineral and a primary component of the ore, may be the greatest contributor of these ions in solution in the form of CO32- ions. Thus, different sources of CO32- ions (from dolomite dissolution and from Na2CO3) were investigated. The research work aims at elucidating how these reagents may influence the minerals’ surfaces. The results have shown that dolomite supernatant and sodium carbonate greatly affect the electrokinetic properties of each minerals. The addition of dolomite supernatant have resulted to relatively similar zeta potential of the minerals; while, sodium carbonate have affected them differently. These observations could be useful in efficient flotation of bastnäsite and/or monazite from bastnäsite-monazite-dolomite system.INTRODUCTIONThe increase in the demand for rare earth (RE) elements has driven the search and development of new deposits. Out of 53 rare earth projects in the world, 19 can be found in Canada (Hatch, 2015). These include the Niobec project of Magris Resources Company in Quebec. This deposit contains a significant amount of rare earth minerals (such as bastnäsite and monazite), with carbonates (such as dolomite) as the primary gangue minerals."

Jan 1, 2016

By Deepak Bhadouriya, Saurabh Singh, Aditya Raj Suman

"An experimental study of chemically enhanced filtration and dewatering of fine coal slurry with and without additives was carried out. The experiment involved determination of effect of slurry concentration, additives (cationic, anionic and nonionic), filter area, filtration velocity, particle size and cake resistance on dewatering and filtration using vacuum filtration cell. Finally, the rate of filtration and dewatering and optimum amount of additives used were determined under suitable filtration condition. Overall, it was found that the filtration and dewatering characteristics were enhanced by increased slurry concentration, larger filter area and larger particle size. In addition of additives, the kerosene was found to be best for enhancing the filtration which yielded cake moisture reductions of approximately 17% by weight. At optimum dosages, the final cake moisture contents were reduced by 3.6% and 5.8% by weight using the appropriate surfactant and flocculent, respectively.INTRODUCTIONFor India, it is estimated that coal constitute a principal source of energy for the next several decades. It is majorly used at thermal power plants to generate electricity and also to a great extent in steel and cement industry. It has been observed that its consumption is increasing so as to meet the energy requirements of the country. It has been found that in a coal preparation plant; approximately 20-25 percent coal is of the mined coal of the range below minus 0.5 mm (28 meshes). Generally, this fine fraction is discarded due to its high cost of processing and further utilisatisation is very minimal. But with ongoing research and development for advanced clean coal technology, various new techniques have been evolved to maximize the utilization of available coal. In recent time technologies such as column flotation, cleaning of fine size coal to lower the ash content and low pyretic sulfur is feasible at high recovery value. But in various researches it is found that one of the biggest hurdles in utilization of fine coal cleaning technology by the coal industry is the economic dewatering of the fine clean coal product. Thus, until an economical and practical solution to dewatering of fine clean coal is achieved, the efforts devoted to developing fine clean coal technology will be wasted. In this paper an effort toward enhancing and developing the optimum technique of dewatering and filtration of fine coal slurry has been made."

Jan 1, 2016

By S. Banisi, A. Haji-Zadeh, A. R. Hasankhoei, M. Maleki-Moghaddam

At the concentration plant of the Gol-E-Gohar Iron Ore Company (Iran) three 9m × 2.05m AG (Autogenous) mills (fixed speed) are used in parallel in a dry operation. The test works conducted in a scale down mill with a diameter of 1m indicated that conventionally used "deflector" type liners did not provide efficient environment for grinding. In this research, to improve the grinding efficiency, a new design using low profile end liners incorporating radial ribs of proper height was investigated. In order to determine an appropriate liner design at different operating conditions, a 100cm×10.8cm model mill was used for experimentation. The special design of model mill made it possible to increase the radial ribs height in steps of 6mm up to 18.5mm. The transparent end of the mill enabled accurate trajectory determination by image analysis. The results indicated that the new lower height profile deflectors and 15.5mm-height (14.5cm in industrial scale) radial ribs improved the mill performance while avoiding excessive pressure drop across the mill and wear on the liner. The image analysis showed that the use of new liners increased the distribution of coarse particles across the mill cross section from 28% to 35%. A new liner design was proposed by decreasing the number of liners in each slice from 5 to 4 pieces. The thickness of the inner head liners reduced from 45cm to 30cm and the outer deflector liners replaced by radial ribs. The distance between the feed and discharge inner head liners increased from the original 115cm to 145cm which increased the effective length of the mill by 26%. The new design reduced the weight and volume of end liners by 9% and 23%, respectively. It was predicted that the new liners design increases the mill throughput by 10% and reduces the metal consumption by 20%.

Jan 1, 2016

By R. O. Loutfy, J. C. Withers

"Titanium powder is produced from a small fraction of sieved sponge, HDH of sponge or gas blown from a melt produced billet. Ore from foreign sources is chlorinated in a very high temperature fluid bed to make TiCl4, then vacuum distilled purified and then reduced to sponge by Kroll processing. Domestic ores of ilmenite or perovskite can be carbothermically reduced to Ti2OC which can be chlorinated at low temperatures of 250–400°C to produce TiCl4 which can be electrolyzed in a fused salt to Ti powder, or the Ti2OC used as an anode in electrolysis to produce Ti powder. The electrolysis process can be operated continuously to produce Ti powder at a lower cost than Kroll processed sponge including produce control size powder. Electrolysis processing was scaled up and operated at the commercial demonstration stage on a continued basis that verifies the potential of a low cost process to produce Ti powder.INTRODUCTIONTitanium and alloys of titanium powder have been elevated to strategic status resulting from a focus of producing meltless titanium components as well as a feed for additive manufacturing processing. However, the high cost of titanium powder has limited wide scale implementation of using titanium powder as a feed to any process to produce titanium components. Titanium powder free of alloying is available as sponge fines from the Kroll process as illustrated in Figure 1. Titanium alloy powder is much more expensive, also illustrated in Figure 1 produced from an alloy ingot or mil product as the feed and then transformed into powder by one of several melt form processes which accounts for the high cost of titanium alloy powder at approximately $60–150/lb. Ton lots of titanium alloy powder (i.e. Ti-6Al-4V) from one source is quoted at $120/lb. in the U.S. It appears that alloy powder production cost by current processing is not sensitive to volume."

Jan 1, 2016

By T. Guan, G. Fu, X. Zhou, L. Deng

"One kind of tailings from gravity separation of polymetallic mine contains 0.5–0.8% SnO2. The proportion of –0.037 mm size fraction of the tailings is 37.12%, and the distribution rate of SnO2 is 60.32% in it. For this tailings, two processing technology was carried out. One was felt-shaking table gravity separation in which the concentrate with a grade of 30% SnO2 at a recovery of 10% was obtained. Another was flotation-gravity separation in which the concentrate with a grade of 51.20% SnO2 at a recovery of 51.69% was obtained, but the dosage of collectors was as much as 990g/t. Therefore, the experimental research on the influence of grain size composition on the cassiterite recovery were conducted. The results show that: (1) the flotation recovery of the cassiterite distributed in +0.043 mm size fraction is only 10%, flotation recovery is not suitable for it; (2) a portion of cassiterite distributed in –0.01+0.005 mm size fraction could be recovered by flotation, but the tin flotation performance will be worsened rapidly and the dosage of collectors will be increased due to the increase of the content of –0.010 mm size fraction; (3) flotation processing is not suitable for –0.005 mm size fraction of the tailings. According to the results, a new technology has been carried out, that is discarding tailings by gravity separation-hydrocyclone desliming-flotation-gravity separation processing flow. The processing index is close to that of the flotation-gravity separation processing flow, and the collector dosage is decreased to 360 g/t by this processing technology. And, it has been achieved that the cassiterite slime is recovered economically and reasonably.INTRODUCTIONAs the density of cassiterite is higher than that of gangue, gravity separation is considered to be a low cost, pollution free, and effective process for cassiterite recovery (Wills, 2009). However, cassiterite is a kind of fragile mineral, over crushing is easy to take place and a large amount of slime is inevitably produced in the crushing and grinding of cassiterite. For the cassiterite slime exists in –0.043 mm size fraction, the efficiency of gravity separation decreases sharply. The production practice shows that, for the fine cassiterite, the recovery of tin exists in –0.043 mm +0.010 mm size fraction is about 13% through shaking table gravity separation, and the tin exists in –0.010 mm size fraction is almost impossible to be recovered by gravity separation. If flotation is adopted to recover fine cassiterite, the problems of high reagent dosage, high cost, environmental pollution, and poor economic benefit would take place. Therefore, the recovery of cassiterite slime is a worldwide problem. A key way to increase the utilization of tin resource and increase the economic benefit of tin mines is developing suitable beneficiation process for fine cassiterite."

Jan 1, 2016

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Megan Becker, Aubrey Mainza, Indigo Research Laboratories, Jenny Wiese, Gaynor Yorath, Lucy Little

Particle shape characterisation has an important role to play in mineral processing, to clarify effects of shape on rheology, equipment wear rates, comminution, classification, sizing and flotation. However in industry, shape characterisation is not routine, and the most commonly used shape descriptor in the field (circularity/ angularity/ sphericity) is not invariant. This study aims to investigate shape measurements for a fine particulate ore sample measured with different analytical devices. Two Automated Scanning Electron Microscopy devices with Energy Dispersive X-ray Spectrometry (FEI QEMSCAN® and Zeiss Mineralogic®), and a camera based image-sizer using dynamic image analysis (Retsch CAMSIZER® XT) were compared. Each device was used to analyse the shape characteristics of specific particles in both a coarse sample (–212/+150 µm) and a fine sample (-53 µm) of UG2 platinum ore. Circularity and Roundness frequency distributions obtained from the three devices were then compared. For selected individual particles, circularity showed higher variability than roundness, and the sample circularity distributions obtained by the three devices were completely different. It is clear that circularity data from different studies relying on different devices should not be compared on an absolute scale. The shape parameter roundness was found to be a more robust descriptor than circularity, and it can give a stronger indication of a particulate sample’s shape characteristics on an absolute scale. However, there were still significant differences in the roundness measurements obtained by the CAMSIZER XT and the two Auto-SEM devices, which was attributed to the dissimilar mechanisms of image capture.

Jan 1, 2016

By G. M. Ross, I. M. Ross, J. A. Scott

"The otherwise waste heat in many water streams in the mining industry can be used to provide space heating of adjacent infrastructure including laboratories, workshops, and offices. This can be achieved by using heat pump systems, which can work as a replacement or in conjunction with existing space heating. In the example investigated—process cooling streams at an ore smelter—the analysis provided illustrates that annual heating costs can be 19% lower and a simultaneous 62% reduction in CO2 emissions can be achieved.RÉSUMÉ Dans l’industrie minière, la chaleur qui serait normalement perdue des circuits d’eau pourrait servir à chauffer des structures adjacentes incluant les laboratoires, les ateliers et les bureaux. Cela pourrait se faire en utilisant des systèmes de thermopompes, qui pourraient remplacer ou s’ajouter au chauffage existant. Dans l’exemple étudié, des circuits de refroidissement de procédé à une fonderie, l’analyse fournie illustre qu’il est possible de réduire les coûts annuels de chauffage de 19 % et d’obtenir une réduction simultanée de 62 % des émissions de CO2."

Jan 1, 2016

By M. Lebeuf, A. Dumais, C. Farsangi, N. Singh

The Nunavik Nickel project began ramp-up of a new ore body (Expo) in November 2014. This new deposit is significantly more competent than the previous ore type milled (i.e., the plant moved from a feed with a BWI of 12.2 kWh/t to predominantly material with a BWI of 19.6 kWh/t). Despite circuit changes made in advance of the Expo ore ramp-up (grinding media size, mill loading/power draw, and cyclone configuration) the throughput of the plant was bottlenecked at 90% of targeted throughput with multiple stoppages to grind-out the primary mill due to excessive circulating loads. During this time, the secondary milling circuit was under-utilised: therefore the focus for debottlenecking plant production became increasing the product size of primary milling. Given the scope of changes already made to the circuit, it was decided to test the mill in open circuit. The milling changes were modelled using the Molycop Tools package to identify potential problems. In the modelling and plant trial it was apparent that the ball size in the secondary grinding circuit was inadequate, resulting in pebbling. The power draw of the secondary mill was brought up to minimize pebbling and the average ball size was increased. The switch to open circuit primary milling permitted a significant augmentation in plant tonnage. While the overall grinding efficiency decreased using the open circuit configuration, the ability to increase throughput made it the clear operating choice.

Jan 1, 2016

By X. Cao, H. Huang, Z. Dai

"Crystal phase of copper-containing slag regulation by the slag viscosity, cooling speed and cooling method, where the slag viscosity is related to the temperature and alkalinity. According to the mineralogy properties of a copper-containing slag, experiments of crystal phase regulation and flotation were conducted. When the copper-containing slag that adding a small amount of calcium oxide was cooled slowly at a rate of 3°C/min and about 1050°C n a cinder inclusion system, the viscosity of slag can be remained under 0.25 Pa·S and more than ??% of copper particles that the grain size is larger than 20 ?m in slag. The whole flow of flotation experiment was carried out to recover copper from the copper-containing slag with crystal phase regulating and the copper concentrate grade was ?????%, the recovery efficiency of copper was 94.18%.INTRODUCTIONChina's annual output of copper slag is more than 6 million tons, the current total has reached 80 million tons. It is equivalent to 640 thousand tons of copper metal with the copper grade of 0.82%. Most of the smelting slag were storage. It is not only occupy the land and pollute the environment, but also make a huge waste of resource (Alp, Deveci, & Süngün, 2008; Carranza, Iglesias, Mazuelos, Romero, & Forcat, 2009; Gorai, & Jana, 2003), therefore, it is good way to achieve copper slag resources by the effective recovery of valuable component from copper smelting slag, which is an important measure of the current process of copper smelting slag and implement the central authorities to vigorously develop the circular economy, improve the recycling of resources, increase copper production of intensive development (Zhou, et al., 1994; Zhang, Zhang, & Wang, 2005). Currently, researches on comprehensive utilization of the coppercontaining slag made a much progress (Wei, 2004; Liu, Gai, Yang, Sui, Li, & Fu, 2008; Liu & Zhu, 2008; Zhang, 2010; Sun, Chen, & Tang, 2012; Qin, Wang, Ren, Wei, Peng, & Gu, 2012). Flotation is one of the most effective method to recover the copper from smelting slag, which has the features of low cost and high efficiency (Song & Liu, 2001; Zhang, Wang, & Li, 2012). But the copper particles in the copper smelting slag distribution is very uneven, and the thickness of the material is very serious. The copper content in the micro level is higher, the size of copper sulfide ore is less than 0.043 mm, which leads to the difficulty of the monomer dissociation (Tossavainen, Engstrom, Yang, Menad, Lidstrom, Larsson, & Bjorkman, 2007; Moustakas, Mavropoulos, Katsou, Haralambous, & Loizidou, 2012). In this study, according the process mineralogy of a smelting copper slag, the crystal of smelting copper slag was optimized by controlling the temperature, alkalinity, cooling rate and cooling method, which makes the fine copper mineral particles in the copper slag crystal further, and can be used to meet the particle size requirements of flotation, thereby enhancing the flotation of copper."

Jan 1, 2016

By Jianwen Yang, Yucai Zhou, Yanhong Dong, Daixiong Chen

"The study of combined depressants for flotation separation of lead from copper has been carried out to solve the copper-lead separation problem. Test results show that the depressant of CMC (Carboxyl Methyl Cellulose) or sodium sulfite plays an important role on the selective depression of galena flotation. When the two reagents above are combined, the selective depression effect on galena is further enhanced. When the mass ratio of CMC to sodium sulfite is 1:4, galena was best depressed, with the lowest lead content in the copper concentrateClosed-circuit tests indicate that under a certain pH value of the slurry, with the best ratio of CMC to sodium sulfite as depressants, the copper concentrate with the grade of 28.23% copper and 4.12% lead is obtained, and the copper recovery is 84.87%; the lead concentrate with 68.12% lead and 0.86% copper is obtained, and the lead recovery reaches to 92.20%. An efficient separation of copper and lead is achieved with the combined depressants. INTRODUCTIONComplex copper-lead-zinc sulfide ore is abundant in China. With the rapid increase of mineral consumption, it has become one of the important sources to produce copper-lead-zinc metals. However, it is difficult to achieve effective separation of copper and lead, due to the complicated ore properties, such as fine dissemination, low copper grade, complex symbiotic relationship and similar floatability of copper and lead.Poisonous reagents of bichromate and cyanide are often used as depressants for copper lead separation. They have good separation efficiency, but pose serious pollution issues. As the environmental protection is becoming more and more important, it is a trend to replace traditional toxic reagents with new nontoxic efficient chemicals. Organic depressant FCLS studied by Liu has strong selectivity against galena, and does not depress chalcopyrite. A new type of galena depressant of CLS-01 discovered by Jin-lin Yang shows good results in the separation a mixed copper and lead concentrate. In addition, dextrin, chitosan and some other natural organic compounds (Drzymala, 2003; Huang, 2012; Qin, 2013) have also been studied to separate copper and lead."

Jan 1, 2016

"The Mine Haul Road Optimization Alliance is an Australian industry-academia collaboration which has been developed to support mine haul road operators by fully integrating mine road design research solutions with industry end-user service providers to design, assess, implement and monitor the various equipment, materials and road management strategies required to optimize the safety, environmental and economic performance of a haul road. Initially, a broad overview of the university-industry collaborative landscape is presented, following which the current situation in the Australian mining sector is reviewed both nationally, and on a country-wide basis, internationally. This insight places realization of a collaboration between Curtin University Western Australian School of Mines Mining Engineering and Metallurgical Engineering (WASM ME2) and the Haul Road Optimization Alliance (HROA) industry members into context of opportunity. Following an overview of the HROA collaborative structure, aims and objectives, it is shown how academia and industry can collaborate to deliver a more robust solution to mine haul road design, performance or management needs, especially where integrated solutions are needed. Critically in this approach, implementation and monitoring data provided by industry and service-providers alike forms the foundation on which to develop research knowledge and innovation that is more responsive to the end-user requirements, typically represented by ‘early goals’ and implementable solutions. The paper concludes with examples of how the alliance collaborations work in practice to deliver improved mine haul road designs and optimized operational performance, together with the mechanisms used to ensure industry needs are met through focused, end-user driven research and integrated solutions implementation."

Jan 1, 2016

By D. Neely, D. Milne, L. R. Feldman

"Resin-anchored rebar is commonly used for rock support in mining. The rock properties and environment determine the average bond strength, allowing mine engineers to select the appropriate length and installation pattern for the support. In weak material such as potash, the average bond strength tends to be lower than for a typical hard-rock installation. Determining the failure mechanism by which the support fails in soft-rock applications could lead to improved bond strength and better calculated installed support capacity. This paper reports on research conducted at a potash mine in Saskatchewan and analyzes the failure mechanism of the support.RÉSUMÉ Dans les mines, les barres d’armature enduites de résine sont fréquemment utilisées pour soutenir le roc. L’environnement et les propriétés du roc déterminent la résistance moyenne d’adhésion, permettant ainsi aux ingénieurs miniers de choisir la longueur de barre appropriée et le diagramme d’installation du soutien. Dans des matériaux faibles, tels que la potasse, la résistance moyenne d’adhésion tend à être plus faible que pour une installation typique dans de la roche dure. La détermination du mécanisme de rupture selon lequel le soutien fait défaillance dans des roches tendres pourrait conduire à une meilleure force d’adhésion et à un meilleur calcul du soutien installé. Le présent article fait état de la recherche effectuée dans une mine de potasse en Saskatchewan et analyse le mécanisme de défaillance du soutien. ,"

Jan 1, 2016

By A. R. Sheik, A. A. Baba, M. K. Ghosh, K. Sanjay, R. B. Bale, A. G. F. Alabi, F. A. Adekola, L. Ibrahim

"This paper studies the characterization and dissolution of a Nigerian pyrolusite ore, reporting the results of ore physicochemical analyses and detailed ore characterization before and after leaching at optimal conditions. Ore dissolution rate increased proportional to acid concentration and temperature, but decreased with ore particle size. In a 4 M H2SO4 solution at 80°C with a particle size of –90+75 µm and moderate agitation, ore dissolution rate reached 78.7%. Unleached residue produced under optimal leaching conditions consisted of silica with admixtures of cristobalite and stishovite. The calculated activation energy supported the proposed diffusion control mechanism for the process.RÉSUMÉ Le présent article étudie la caractérisation et la dissolution d’un minerai de pyrolusite du Nigeria, il donne les résultats des analyses physicochimiques du minerai et de la caractérisation détaillée du minerai avant et après la lixiviation sous des conditions optimales. Le taux de dissolution du minerai augmentait proportionnellement à la concentration de l’acide mais décroissait avec la taille des particules. Dans une solution 4 M H2SO4 à 80 °C, avec une granulométrie de –90+75 µm et une agitation modérée, le taux de dissolution du minerai a atteint 78,7 %. Les résidus produits sous des conditions optimales de lixiviation étaient constitués de silice avec un mélange de cristobalite et de stishovite. L’énergie calculée d’activation supportait le mécanisme de contrôle de la diffusion proposé pour le procédé."

Jan 1, 2016