Search Documents

By Leonardo Rosas Sánchez, Darío Ángel Bulla

"The two track road sector between Cisneros-Loboguerrero (having a length of 14 km and 11 short unidirectional tunnels) is a new highway still on construction located along the existing Highway Buga – Buenaventura (Colombia). Due to the steep topography, difficult geological/geotechnical conditions, the traditional portal construction approach was impossible to be implemented in eleven (11) of the twenty two (22) portals. In this specific project, the skewed portal approach was developed as the optimal and more effective solution. The construction time and costs of portals were reduced in 21 months and 75%, respectively. At the same time, the natural equilibrium of the slopes was maintained, thus, facilitating adequate safety factors along the useful life of the project. This document pretends to show a detailed design experience (and the construction of the entry portal of tunnel 11 (left)). INTRODUCTION The Cisneros-Loboguerrero project is a 14 km length dual lane highway, connecting productive zones with the Pacific Ocean along the current Bogota-Buenaventura highway as shown in Figure 1. The project is located at the northern side of the Dagua River Valley. The preliminary design suggested constructing portals under challenging topographical conditions, i.e., slope cuts having heights between 50 to 100 m (some having slopes > 100%) requiring complex developments and having very high risks.The entry portal of tunnel 11 (left) was the first portal successfully built by implementing the skewed portal approach. Later, this approach was used as a model for the construction of the other ten (10) portal having similar topographic and geotechnical conditions. The development of this new alternative provided a considerable reduction on the construction time of portals, thus relieving a critical path in this project."

Jan 1, 2016

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By C. Musingwini, A. S. Nhleko

"Since the Global Financial Crisis (GFC) in mid-2008, capital has been more difficult to access. Mining projects must contend with projects from other industries for scarce capital. A decision to invest available capital in mineral projects requires that valuation be conducted to assess the expected return on the projects. The discounted cash flow (DCF) analysis is generally applied for the valuation of mining projects, whereby future cash flows are discounted to present value using an appropriate discount rate. The discount rate significantly affects the outcome of a valuation. Economic and finance theory provides tools to calculate discount rates. The discount rate must account for factors such as the risk and stage of development of the mineral project; hence the appropriate discount rate to utilize in a project is often a subject of debate.The discount rate is the weighted sum of the cost of debt and equity. There are several methods for determining the cost of equity. This study considers the commonly applied Capital Asset Pricing Model (CAPM) and Gordon’s Wealth Growth Model because of their simplicity and availability of parameters required to estimate the cost of equity. This study explores how differences in the cost of equity obtained by these two methods can be explained for a mining environment. Data for empirical analysis were collected from the I-Net Bridge, McGregor BFA, and Bloomberg databases. It was found that Gordon’s Wealth Growth Model provides better estimates of the cost of equity compared to the CAPM under depressed market conditions. Therefore, this research recommends that Gordon’s Wealth Growth Model be used to estimate the discount rates for mining projects during periods of depressed market conditions."

Jan 1, 2016

By P. Hickey, G. Hubert, P. Healy

"J. S. Redpath Limited, an underground contractor with a worldwide presence, has implemented innovative techniques in various projects in Canada to shorten the development cycle. Conventional methods currently used for installing primary ground support are compared with the Australian technique of bolting and meshing with jumbos equipped with twin telescopic booms, in-cycle shotcreting, and the use of two jumbos and two scissor bolters set up side by side in wide headings. Recommendations and lessons learned are presented with the aim of providing realistic expectations with regard to development advance rates in a mining environment.RÉSUMÉ J. S. Redpath Limitée, un entrepreneur minier souterrain d’envergure mondiale, a complété plusieurs projets au Canada où des techniques novatrices ont été mises en oeuvre pour raccourcir le cycle de développement. Cet article présente une comparaison entre les méthodes conventionnelles fréquemment utilisées pour le support de terrain, la technique australienne de boulonnage et d’installation de grillage au moyen de jumbos équipés de flèches télescopiques doubles, du béton projeté appliqué durant le cycle de développement et de l’utilisation de deux jumbos et deux boulonneuses côtes-à-côtes dans des galeries de grandes dimensions. Les recommandations et les leçons apprises sont présentées dans le but de fournir au lecteur des attentes réalistes quant aux taux d’avancement du développement dans un environnement minier."

Jan 1, 2016

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By Romel Villanueva L.

"Peru does not produce ammonium nitrate; nevertheless it is a large consumer of both, porous prill (PP) and high-density (HD) varieties. Explosives cost is an important preoccupation in Peru, due tofluctuations of the imported ANFO grade Ammonium Nitrate (AN). The use of Gasified Emulsion (GE)-manufactured with much cheaper HDAN- has become an alternative to reduce such costs. However, some problems were reported in the application of pure GE, including explosive percolation in highly fractured rock and lack of sensitivity by the effect of hydrostatic pressure in very deep holes. It was, hence, proposed to have an explosive based on GE too, but more robust and capable to keep the shape of the explosive column into the blast hole, by minimizing the leakage into the cracks. This could be achieved by adding limited amounts of lower priced HDAN, at the same time of providing gas pressure benefits. Other alternative is to add a low-density material, such as polystyrene prills, into the GE, although it reduces the explosive energy. The chemical gassing controls the density of GE, thus it can be obtained a wide range of densities."

Jan 1, 2016

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By M. Maccagni, J. Nielsen

"Engitec developed the EZINEX® Technology some years ago to recover zinc from oxidized secondary sources. This process works at neutral pH and can take into solution any kind of metal, but iron is rejected and remains in the leach residue. Engitec has also developed the FLUOBORATE System, which is able to recover lead and copper from relevant concentrates. Some iron is leached into solution, but it is controlled through a solution purification bleed treatment. In this paper, we present the two above mentioned technologies. They are very different with regards to the chemical environments and the methods used to control the build-up of iron in solution, but both systems are suitable to treat iron bearing feeds.INTRODUCTIONIn the design of hydrometallurgical processes, the most important issues are the water balance, the filtration and the control of impurities. This is particularly important when the process includes an electrowinning unit. Iron has been one of the most problematic elements to remove, especially in acidic environments.Engitec Technologies has developed several hydrometallurgical processes divided in two different electrolyte lines: the Fluoborate Technology for the recovery of lead and copper from primary and secondary sources and the Ammonium Chloride System based on a chloride electrolyte for the recovery of different non-ferrous metals, among which zinc and lead are the most important. In both cases, iron is present in the feed and needs to be eliminated from the solution. It is not a problem for the quality of the metal produced, but when present in solution, it consumes the basic electrolyte reducing its free concentration which is very important both for both the leaching and electrowinning unit operations. Both process systems are very peculiar, the fluoborate case being much more intriguing."

Jan 1, 2016

By L. J. Bryson, C. A. Biley

"Anglo American Platinum’s Rustenburg Base Metals Refiners (RBMR) produces Ni and Cu cathode from slow cooled converter matte after Platinum Group Metals (PGMs) are magnetically separated for further processing. In 2010, execution of the RBMR expansion project was commenced to increase the production capacity to 33 ktpa Ni. The expansion, which is currently still in a ramp-up stage, brought about several fundamental changes to the circuit chemistry, including the installation of a dedicated Pressure Iron Removal (PIR) autoclave. This provided an independent outlet for iron from the refinery, which previously deported to the residue from the leach circuit and was toll refined. At the same time as changes in the circuit associated with the RBMR expansion were being made, the plant experienced a significant increase in iron and copper units per nickel unit in the feed. The decoupling of the leaching and iron removal process steps has had significant advantages for the robustness and control of the overall circuit, in particular pertaining to the preparation of a nickel electrolyte of sufficient purity to produce LME grade nickel. This paper details the primary changes to the RBMR circuit chemistry with a particular focus on iron deportment and the benefits derived from the installation of the PIR autoclave.INTRODUCTIONAnglo American Platinum mines and refines Platinum Group Metals (PGMs) through a complex processing pipeline in its South African operations. Mined ore is first treated through several mineral processing stages, geared to the recovery of base metals and associated PGMs, followed by smelting and refining operations that aim to separate base metals from PGMs and recover the value components to purified, saleable products. The focus of this paper is the Rustenburg Base Metals Refiners (RBMR) complex which receives a PGM-containing converter matte, then physically separates PGMs and base metals, and recovers nickel and copper to cathode by utilising leaching, precipitation and electrowinning processes.With new mining operations coming online and the continued increase in PGM ore arisings, it was necessary to undertake an expansion project at the Base Metal Refinery (BMR) to increase production capacity from 21 ktpa to 33 ktpa Ni. Complicating the expansion project was the requirement of continued production through all stages of design, construction and implementation and, due to stringent capital constraints, the utilisation of all existing equipment installed during a previous expansion in 1981. Against this backdrop, the expanded BMR flow sheet involved significant changes to the chemistry, especially iron management. These changes in iron management allowed for the separation of iron and copper residues and significantly increased the robustness of the plant to changes in feed mineralogy as well as the potential to increase production duties of the existing equipment."

Jan 1, 2016

By C. Birch

"A mineral resource royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In South Africa, this payment is made to the State as holder of the mineral rights (The Mineral and Petroleum Resources Royalty Act of 2008). The principle purpose of this research paper is to identify if the State is benefitting from the mineral resource royalty by considering its impact on seven individual Witwatersrand gold mines.For this study, a simple financial optimiser model was created in Microsoft Excel that links the ore flow, block listing and the cash flow (excluding or including the cost of the mineral resource royalty). Mixed integer linear programing (the Excel Solver function) is utilised to optimise either profit or NPV (at 9% and 12%) by adjusting the cut-off grade.The impact on each of the seven mines mine was different but overall R7.9 billion is estimated to be paid in mineral resource royalty over their expected remaining lives. Due to the cost of the mineral resource royalty and increasing the cut-off grades, the total revenue decreases by R10 billion. A significant portion of this lost revenue would have been paid to the State in the forms of other taxation including company income tax which decreases by R2.8 billion. It is recommended that an industry wide investigation be conducted to determine if the resource royalty is adding to the State’s revenue, or destroying value including premature job losses. IntroductionTaxation of mining companies has become a very topical subject in the context of the postapartheid South African economy. There have been increasing calls for equitable re-distribution of mineral asset wealth for the benefit of all South African citizens and not just to an elite few. As part of the Mineral and Petroleum Resources Development Act (MRDPA) of 2002, the Mineral and Petroleum Resources Royalty Act of 2008 was introduced and came into effect in 2010 (South African Revenue Services, 2008). A mineral royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In the case where the holder of the mineral right is the State, then this payment is made to the State (Cawood, 1999). Studies on the potential impact of the mineral resource royalty on the minerals industry have been conducted during the formulation of the Act and subesquently. These include Cawood and Macfarlane (2003), who suggested a cap of no more than 3% (Cawood and Macfarlane, 2003), as well as Cawood (2011), who predicted rising cut-off grades and thus reducing mineral reserves. In 2013, Grobler completed a Masters in the Faculty of Economic and Management Sciences at the University of Pretoria and concluded that the impact of the mineral resource royalty on the economy is positive. She stated that the royalty has caused operating expenses to increase, but this does not appear to be significant. Furthermore, she stated that the royalty has not affected the way the mining industry operates (Grobler, 2014)."

Jan 1, 2016

By Elbasher M. E. Ahmed, Indresan Govender

"A mechanistic model of axial charge segregation in rotating drums is presented. We show that granular material composed of different frictional properties diffuse into axial bands as a consequence of concentration fluctuations in the free surface layer that is caused by friction-limited mobility. A Bagnoldian stress assumption ensures an asymmetric free surface profile thereby providing the essential ingredients for the evolution of axial bands and the subsequent band coarsening observed in the literature. The formulation is sensitive to the boundary conditions of tumbling mills, including particle size and density, mill speed, inter-particle bulk friction, end wall friction and drum geometry (length and diameter).INTRODUCTIONA mechanism to fully describe the axial segregation of charge in a rotating drum remains elusive to the mineral processing industry. With regard to low aspect ratio mills (like ball mills), current thinking favours the use of closed circuit mills with correspondingly low residence times to offset the completely random contact probabilities between particles and balls (Wills & Napier-Munn, 2006). Conical end caps are argued to exploit the centrifugal force to achieve a regular gradation of ball size along the mill with larger sizes at the feed end and smaller ones closer to the discharge. However; segregation along the length has been observed in the absence of conical end caps (Oyama, 1939; Levine, 1999): In these investigations, sufficient differences in the particle’s mechanical properties (particle size, density, shape, surface roughness) was enough to successfully achieve axial segregation. Figure 1 shows the segregation of a bimodal distribution (by size) into bands of larger (darker colour) and smaller (lighter colour) particles."

Jan 1, 2016

By Troy Williams, Chris Preston, Ian Lipchak

"Underground blasting operations are challenging from the standpoint of the distribution of explosivesenergy representative of ring blasting. Energy from both shock and pressure regimes of commercialexplosives may appear concentrated in the collar region of a typical ring blast and diluted at the toes of holes due to the oblique geometries of blastholes. The non-homogenous nature of ore in whichexplosives are distributed via drillholes, adds to the complexities of generating particulate profiles from fragmented material with consistencies that are predictable from blast pattern to blast pattern - well suited for specific underground handling equipment and mill processing. In an ideal world, it would be the blasting operations themselves that represent the primary crushing mechanism, or at least mitigate mechanical crushing that can comprise a large component of the cost in generating suitable muck. This paper presents a dynamic break view in 3D that allows a planner to visualize the potential break zone around a blasthole generated by an explosive load using a Kleine field. Simple as it sounds, this methodology provides information that can be used in conjunction with cavity monitoring surveys (CMS) to potentially judge dilution due to overbreak as well as recovery for a typical blast. As examples, there are two break geometries that are examined regarding circular breaks and elliptical breaks around blastholes. Using a Kleine field to define break, a planner generated isosurface can be generated and compared to CMS data for calibration and prediction, using AEGIS 3D ring design software."

Jan 1, 2016

By R. C. Gilmore, S. A. Lolon, G. E. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Gob ventilation boreholes (GVBs) are widely used in underground coal mines for longwall gob degasification purposes. GVBs are often drilled within 10 to 30 m above the top of the coal bed into the fractured zone, completed with 20 cm (8 in.) diameter casing and 60 m of slotted pipe at the bottom. The purpose of this completion strategy is to create a pressure sink to capture the emissions before they can enter into the underground workplace. For GVBs to work effectively, they must be drilled close enough to the working areas to capture methane from the fractured zone while the setting depth must be kept above the caved zone to minimize the amount of ventilation air that is drawn into the GVBs. Well completion parameters are important for creating safe working conditions. In this paper, computational fluid dynamics (CFD) studies will be presented to analyze the effect of different practices for GVBs completion parameters for methane extraction, formation of explosive gas zones in the gob and methane concentrations at the longwall face and tailgate. Authors have identified the optimum completion parameters for GVBs, which can maximize the benefit and minimize fire and explosion risk. INTRODUCTION Coal mines may be considered gassy based on the presence of CH4. Gas from the mined coalbed or from rider seams above or below the mined coalbed can migrate into the gob and then potentially move towards the working areas. In longwall coal mines with high methane emissions, sufficient ventilation and additional methane control measures are usually required to reduce the methane concentration in working areas to below statutory levels. Several techniques or combinations of techniques are available to control the methane hazard. These may include mine face ventilation to dilute methane, coal bed degasification, nitrogen injection into the gob to render a methane atmosphere inert and the use of gob ventilation boreholes (GVBs). Longwall face ventilation and dilution alone can only handle methane emissions up to a certain amount. When methane emissions exceed the face ventilation capacity, additional control measures are required. Drilling horizontal or vertical methane drainage holes into the coal seams as well as gob ventilation boreholes from the surface into the gob area to extract methane are common practices. GVBs are usually drilled from the surface above the longwall panel ahead of mining. When the face moves outby the GVBs and the gob begins to form, methane production starts from the boreholes. It is important to control the performance of GVBs to maintain a safe working environment in the mine. The performance of GVBs depends on multiple factors, including borehole location, length and diameter of slotted casing, setting depth of casing above the coal seam being mined, wellhead vacuum pressure, and permeability of caved-fractured zones."

Jan 1, 2016

By C. Dodds, R. S. Ferrari-John, The University of Nottingham, G. Dimitrakis, J. Katrib, A. R. Batchelor

"Sorting technologies have the potential to reduce energy use in comminution by rejecting uneconomic ore before feed material enters the mill. However, a major challenge for sorting porphyry copper ores is providing a basis of discrimination between valuable and non-valuable fragments, due to their complex mineralogies and textural features. Microwave heating in combination with infra-red detection (MW-IR) has been shown to provide upgraded feedstock for certain ores at bench scale. Selective heating of copper sulphide minerals compared to the gangue leads to an increased thermal response for valuable fragments, providing the basis for sorting.Rapid scale up of MW-IR from bench scale to a 100 t/h continuous pilot plant facility has been facilitated by the design of microwave choking structures to allow continuous operation at industrially meaningful throughputs, whilst meeting health and safety and electromagnetic compliance standards, and the integration of materials handling with electromagnetic systems.Laboratory batch testing on a pilot scale microwave system has been undertaken to investigate the thermal response of copper ores under industrial conditions, at microwave energy inputs up to 1 kWh/t. These results provided the operating window and recommended test conditions for the continuous pilot plant. Sortability curves predicted in the laboratory are in good agreement with separations achieved during continuous pilot plant operations. The potential microwave sortability of a number of ores has been studied, allowing informed decisions to be made about potential ore candidates based on mineralogy. Future development of the technology will be underpinned by the creation and validation of scale up concepts for 1000 t/h operations. Understanding the value proposition for individual sites/applications will be central to unlocking the potential economic and environmental benefits of microwave sorting."

Jan 1, 2016

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By Corby G. Anderson, Caelen D. Anderson, Patrick R. Taylor

"The United States contains a variety of domestic rare earth element mineral sources containing such as ancylite, bastnasite, monazite, and xenotime. Research has been performed to investigate the fundamental surface chemistry involved in the froth flotation of these minerals, and apply the knowledge gained to substantiate the results through experimental testwork on a domestically sourced rare earth ore. This paper will outline the fundamentals and literature of rare earth mineral flotation, review its industrial applications and provide some recent research updates.THE RARE EARTH ELEMENTSRare earth elements (REE’s) are a unique family of elements with nearly identical physical and chemical properties. They account for approximately 1/6th of all naturally occurring elements, but the entire group occupies only one position on the periodic table. These 15 elements make up the lanthanide series (atomic numbers 57–71), and all but one (promethium) occur naturally. In addition to these 15 elements, yttrium and scandium are also considered rare earths since they tend to occur in the same deposits as the rare earths and share similar physical and chemical properties as seen in Figure 1. In particular Figure 2 denotes, a cartoon of the subtle differences in each caused by the 4f atomic sub shell (Gschneidner Jr., 1964). These subtle differences result in very difficult challenges in the selective concentration and final separation of each rare earth. (Anderson, 2015, Kronholm, Anderson, Taylor, 2013)Rare earths are separated into two different subsections; the “lights” or LREE’s (lanthanum57 through europium63) and the “heavies” or HREE’s (gadolinium64 through lutetium71). Yttrium is generally considered a heavy rare earth since its ionic radius is close to that of the HREE’s, while scandium is not considered either a light or a heavy."

Jan 1, 2016