Search Documents

By H. R. Manouchehri, A. Weh

"High voltage electric pulse comminution (SELFRAG) relies on inducing electrical breakdown that occurs when the resistivity of a dielectric is insufficient to completely block all transfer of electricity while the conductivity is not high enough to fully accommodate the flow of electricity without considerable changes to the crystal lattice. The technology is based on introducing the electrical discharges into solids immersed in water and placed between two electrodes. The technology has received significant attention since investigations have revealed the potential for fully fragmenting particles or pre-weakening rocks in order to reduce the energy consumption in comminution practices, improve liberation and potentially increase the recovery in mineral processing. Mineralogical analysis of samples showed possible liberation at coarser sizes by high voltage breakage in comparison with conventional mechanical comminution.This study explored the potential of implementing SELFRAG to treat the Sandvik’s Mittersill mine tungsten ore (scheelite) for recovery improvement. Accordingly, standard SELFRAG tests were conducted on four samples from the tungsten process plant to evaluate the energy-breakage relation and potential to liberate the value minerals at coarser size fraction for recovery improvement. The size reduction of the ore after processing with SELFRAG revealed that size deportment occurs at 0.4, 0.2, and 0.1 mm, which indicated potential liberation of gangue and target minerals at respective sizes. In comparison with conventional milling, the difference is the deportment of values into 0.4 mm sizes, which was, to some extent, confirmed by SEM liberation analysis. However, more tests are needed to proof the concept. The study has indicated that, despite consuming more energy in comparison with conventional mechanical comminution, there are promising prospects in liberating the values at coarser fraction and improve recovery by making use of SELFRAG. The energy consumption can be reduced through customized generator and equipment setup, which must be further investigated."

Jan 1, 2016

By Seokwon Jeon, Ho-Young Jeong

"Various numerical methods have been tried to estimate the cutting forces of a TBM disc cutter. In this study, SPH/FEM coupled method was newly employed to improve the traditional FEM analysis. The disc cutter and rock were modeled by Lagrange and SPH codes, respectively. The numerical cutting test was carried out for representative Korean rocks with different cutting conditions. The results show that the cutting forces obtained from numerical simulation had a good agreement with those from LCM tests, and that applying SPH method to rock cutting model has advantages and improvement compared to traditional FEM method. Erosion criterion and erosion limit were not required to simulate the rock fragmentation process, and the cutting forces from the numerical simulation was more stable and accurate. The results indicate that the numerical simulation can be successfully used to estimate cutting performance of a TBM. 1. INTRODUCTION Various numerical studies have been carried out to accurately simulate the limitations of linear cutting machine (LCM) tests. Numerical modelling methods have advantages comparing with full scale tests in terms of cost and time involved. Many numerical methods have been used to simulate rock cutting process by different cutting tools and the studies are summarized in Table 1.In 2D simulations listed in Table 1, because they do not take account of rolling force and horizontal rolling mechanism of a disc cutter, indenter was selected as cutting tool in their modelling. For these reason, 2D modelling is not suitable for rock cutting modelling using a disc cutter. In contrast, 3D numerical models can take account of the indentation process by thrust force and penetration processes controlled by rolling force."

Jan 1, 2016

By Panagiotis Chryssanthakis

"The aim of this study is to give a better understanding for the performance of the composite material RRS and the synergy effect of its components under different stress regimes and while an excavation face advances during tunneling. The lower part of the Q-system scale (i.e. Q-values of 0.4 or less for a tunnel span of 10m) is commonly used for tunnel applications in softer rock formations. This is implied in the updated Q-chart, where the dimensioning of rock support by using Reinforced Ribs of Shotcrete (RRS) comprises the use of fiber reinforced shotcrete, S(fr), rock bolts and shotcreted beams reinforced with steel rebars. In this study, an effort has been made to simulate RRS in a numerical code and to study its behaviour in a real case study. A double tube, triple lane tunnel in weathered tuff has been chosen as reference material for testing RRS under changing load. A rather extensive parametric study has been run by using the same key input rock mass parameters and three different in situ stress regimes (sH/sv =2, sH/sv =1 and sH/sv =0.5). Changes have only been made to the RRS key input parameters in order to simulate the changing loads during the face excavation process in tunneling. The critical part of this numerical modelling work that is under investigation in this study under each stress regime, is the period just after the excavation: i.e 4 hours; 16 hours after excavation; and finally after the complete curing (28 days) of the cement based components. The RRS are installed in three consecutive numerical steps as follows: a) the application of S(fr) on the rock surface in order to even it up for the RRS application; b) radial bolting; and c) installation of the reinforcing steel rebars, that form the reinforced beam. The results are varying and are strongly dependent on the imposed stress regime and they show in general the following tendencies: The axial forces on S(fr) show that S(fr) is almost overloaded during the first 4 hours in all 3 stages. More particularly: For the case with sH/sv =2 a) the axial forces on S(fr) and on the steel rebars are reduced after 16 hours and 28 days; b) the same is observed on the shear stresses in S(fr) and on steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged. For the case with sH/sv =1 a) the axial forces on the S(fr) are reduced after 16 hours and 28 days; b) the same is observed for the axial and shear stresses, as well as moments on the steel rebars, they are decreasing after 16 hours and 28 days; and c) the bolts loads are almost unchanged."

Jan 1, 2016

By Ho-Sung Yoon, Jyothi Rajesh Kumar, Jin-Young Lee

"Global population is a key factor in future energy requirements, especially considering the important elements of global energy resources, electricity production, the accessibility/non-accessibility of electricity, greenhouse gas emissions and the states of nuclear reactors. Everyday human requirements depend on industrial products, and industries need a considerable amount of electricity to run. Nuclear fuel is inexpensive and bolsters industrial growth. As uranium reserves are being consumed rapidly, an alternative source of energy in the nuclear industry is thorium. Here, primary energy supplies by various sources from 1993 to 2011 as well as estimates of future needs to 2020 are discussed. This study finds that primary energy sources are mainly fossil fuels, renewables sources, and nuclear and hydro energy. In addition, growth depends on increases mainly in renewable sources.Recovery of thorium from its ores by using hydrometallurgical routes were described and discussed. The final part of this paper was presented a case study of the thorium extraction from Korean monazite ore leach liquors by using Prieme JM-T diluted in A150 diluent as an extractant system. And possible separation of the thorium from rare earths (REs) and base metals were calculated by measuring of separation factors and finally, the recovery of thorium from loaded organic of Prieme JM-T was established.THORIUM IS FUTURE NUCLEAR FUEL?Global energy consumption is increasing everyday with the high population growth, high industrialization of numerous countries and the higher level of good and services consumption that follows it. If we look at specific sectors of the economy, oil consumption grew by 0.8 million barrels per day, globally, whereas the increase was 0.4 % for natural gas and coal 1.8 % for nuclear power and just under 2.0 % for hydroelectric power (Asheley 2009). Use of renewable sources of energy for power generation and transportation increased by 3% in 2014 (BP 2015)). Thus alternative source of energy must be identified and developed to meet this increasing demand. Thorium is a potential one for the nuclear industry."

Jan 1, 2016

By A. Juganda, Jr. Bogin, S. Saki, R. Gilmore, J. Brune, J. Grubb, S. Lolon

"In longwall mines, atmospheric or barometric pressure fluctuations can disturb the pressure balance between the gob and the ventilated working area of the mine, resulting in a phenomenon known as “gob breathing”. Gob breathing triggers a gas flow across the gob and the working areas and may result in a condition where a methane accumulation in the gob flows into the face area forming an explosive mixtures. This paper discusses results of Computational Fluid Dynamics (CFD) modeling carried out to analyze this phenomenon and its impact on the explosive mixture development under a bleeder-ventilated longwall gob panel scheme. Modeling results indicate that the gas inflow and outflow across the gob and the formation of Explosive Gas Zones (EGZs) are directly affected by the barometric pressure changes. Methane gas and EGZs in the gob expand out toward the face and bleeder entries during the falling barometric pressure. Where methane zones interface with mine air, EGZ fringes may form along the face and in the bleeder entries. When the atmospheric pressure increases, an ingression of oxygen into the gob is observed that can also increase EGZs in volume. The findings from this study help assess the methane ignition and explosion risks associated with fluctuating atmospheric pressures. INTRODUCTION Methane explosions continue to be a daunting risk for underground coal miners, although the number of related fatalities and injuries in the U.S. coal mining industry has steadily decreased since the establishment of the U.S. Bureau of Mines in 1910. Still, the consequences of a methane explosion are often disastrous with multiple fatalities and property damage often leading to permanent shutdown of the mine. Methane is formed during the coalification process and is released from the coal seam to the mine atmosphere when the coalbed is disturbed by mining or natural causes such as earthquakes. If not properly diluted by appropriate mine ventilation, this methane may accumulate in the active mine workings and gob areas. Researchers at the Colorado School of Mines have developed numerical models showing how and where explosive methane may accumulate in gob areas. Historical mine explosions appear to show a connection between mine explosions and fluctuating barometric pressure as a result of stormy weather. McIntosh (1957), Boyer (1964), and Kissell et al. (1973) studied the influence of barometric drops on major coal mine disasters in the United States prior to 1970. Their statistical analyses found that a majority of these disasters occurred in the fall and winter months when the barometric pressures were influenced by unstable weather conditions and noted increased methane content in the mine workings during times of falling pressure. Studies conducted by Fauconnier (1992) and Hemp (1994) found similar connections between methane explosions and barometric pressure fluctuations in a majority of gas explosions in South African mines. Ten out of twelve major mine explosions with five or more fatalities in the U.S. after 1970 were found to have occurred during the months of November through April when barometric pressure swings were more abrupt and intense (Lolon et al., 2015)."

Jan 1, 2016

By Ewan Selers, Gary Cavanough

Drilling automation technology is well advanced and automated drill rigs are in use at a number of operating mines. This is not the case for the other drill and blast processes due to significant technical challenges to overcome. These challenges, with regard to the current “on bench” practices, include placing the initiators, loading the explosive and connecting up the initiation system. Although difficult, these challenges will be solved with engineering advances.

Jan 1, 2016

By D. R. Nagaraj, Napoleon Tercero, Raymond Farinato

"Dialkyl dithiophosphinates are a unique class of collectors used in the flotation processing of Cu- Au, complex polymetallic, and precious metal ores. They are known to exhibit higher selectivity and flotation rates for Cu sulfides, galena, and precious metal values in the presence of other gangue sulfides, than the traditionally used collectors such as dialkyl dithiophosphates and xanthates. They also have an attractive HSE profile. Historically, for most reagents used in flotation, practical methods of chemical usage have preceded detailed scientific understanding of how they work; this applies also to dithiophosphinates. Recently, however, the research community has shown significant interest in this chemistry, and numerous studies have been conducted to understand the fundamentals of interactions of dithiophosphinates with several base metal sulfides and precious metals. A critical overview of fundamental studies, laboratory ore flotation, and plant practice of dithiophosphinates is given in this paper. The findings from these studies are rationalized by drawing on concepts and insights from coordination chemistry. A comparison between the interactions of dithiophosphinates and dithiophosphate analogues with various minerals and metals is also made throughout. We believe that such a critical analysis/overview will be invaluable in identifying gaps in knowledge regarding this important set of compounds, which in turn may provide a basis for the design of studies that can advance understanding of their flotation performance. INTRODUCTIONDialkyl dithiophosphinates are an important member of the class of thiophosphorus compounds that are widely used in flotation beneficiation of base metal sulfide and precious metals ores. Ore flotation studies and plant practice experience have demonstrated their unique properties compared to the traditionally used sulfide collectors such as dialkyl dithiophosphates (their closest analogues) and xanthates. The predominant dialkyl dithiophosphinate used in the industry today is sodium diisobutyl dithiophosphinate (a.k.a. DIBDTPi; AEROPHINE® 3418A1 introduced by American Cyanamid in the late 1970s; Figure 1). The widest application of AEROPHINE 3418A is found in complex polymetallic ores of Cu-Pb-Zn-Ag, Pb-Zn-Ag, and Cu-Zn where it has demonstrated improved recoveries (and flotation rates) of sulfide minerals of Cu, Pb and Ag and selectivity against sphalerite, iron sulfides, and penalty elements (Mingione, 1991). More recently, it has also been used as a collector in the processing of Cu, Cu-Ni, and Ni ores (Guitard et al., 2015) and Cu-Au ores (Dunne, 2005). In general, it is considered to possess the collecting power of xanthates together with the selectivity (against pyrite) of dithiophosphates (Hope et al., 2003a, 2003b), while requiring lower dosages than those reagents (Guitard et al., 2015). AEROPHINE® 3418A has also found an important place in several targeted formulations to improve flotation performance. Other benefits of this reagent include higher flotation rates, having a better HSE (health, safety and environmental) profile2 compared to xanthate, and exhibiting resistance to hydrolysis and oxidation (Guitard et al., 2015). Compared to diisobutyl dithiophosphate (DIBDTP), which is known to contribute significantly to frothing (often leading to over-frothing), AEROPHINE® 3418A is observed to be froth neutral (i.e. it does not alter the existing froth characteristics). As is the case for other flotation reagents, the design and application of AEROPHINE® 3418A has preceded understanding of its behavior at a fundamental level. Recently, there have been numerous fundamental and application studies designed to develop a better understanding of its interaction with sulfide minerals and precious metals. This should help in optimizing its application in flotation and provide a basis to better rationalize its unique selectivity and activity characteristics. Past studies on the interacti"

Jan 1, 2016

By T. H. Etsell, P. Kerr, Qi Liu

"The objective of this investigation was to study the reaction mechanisms during the reduction of iron oxides in the presence of calcium chloride and carbon black as a simplified iron segregation process. The gas phase was analyzed by mass spectroscopy and the solid reaction products were analyzed by scanning electron microscopy. Mass spectroscopy, combined with thermogravimetric analysis and differential scanning calorimetry, revealed the presence of several gases at elevated temperatures over time, and the scanning electron microscope in combination with energy dispersive X-ray analysis illustrated the growth of a metallic iron phase on or near the carbon substrate. The results correlated well with similar copper and nickel segregation processes, but also introduced new insights that challenge the simplicity of the current models. The formation and transport of gaseous iron species to the carbon substrate in the presence of steam and hydrogen were evident during the reduction process that was studied; however, there is more happening at a mineralogical level, based on evidence of a liquid phase resulting in substantial growth due to an apparent fluxing effect created by the calcium chloride.These results help to better explain the chemical reactions and, in turn, the thermodynamics and kinetics of iron segregation processes related to the beneficiation of low grade complex iron ores. The results are also applicable to the production of metallic iron and concentrated titanium dioxide from ilmenite ores. The benefit of this process is that it allows ores in which the iron minerals are intimately associated with gangue minerals to be processed in circumstances where conventional mineral processing techniques are unsuitable or incapable of upgrading the material."

Jan 1, 2016

By Song Mao, Local Joint Engineering Lab of Efficient Util of Dominant Mineral Resources from Karst Regions, Guizhou Key Lab of Comprehensive Utilization of Non-metallic Mineral Resource, Xianhai Li, Qin Zhang, unjian Ye, Guizhou University, Wei Cheng, Zhihong Liu

"Phosphate tailing is a kind of industrial waste that emitted from separation processing of phosphate ores, which is usually discarged to the tailing pond without treatment. Recovery of phosphorus from tailings is of great significance for comprehensive utilization of phosphorus resource. Chemical composition of a micro-fine cryptocrystalline phosphate tailing was investigated by X Ray Fluorescence (XRF) and Inductively Coupled Plasma-Atomic Emission Spectrometry (ICP-AES), and mineral composition and occurrence of harmful elements were analyzed by optical microscope and Scanning Electron Microscope (SEM), X ray Energy Dispersive Spectrometer (X-ray EDS) and Mineral liberation Analyzer (MLA). On the basis of above, effects of those on mineral processing for phosphate tailing was analyzed. Chemical analysis results in combination with microscopy indicated that there is a certain amount of iron and aluminum and it should focus on the removal of them in separation processing. The cryptocrystalline structure, especially the micro banding structure and micro porphyritic structure indicated that there is quite amount of phosphate in fine particles and it should recovery the phosphorus as much as possible when designing the flotation technology for this difficult separation fine phosphate tailing. This study can provide theoretical guide for efficient phosphorus recovery of from fine phosphate tailing by flotation.INTRODUCTIONPhosphate rocks are vital nonrenewable resources and are essential components in agricultural fertilizers and phosphorous-based chemicals (Gharabaghi et al., 2009). About 95% of the phosphate produced around the world is consumed in the fertilizer industry (page 60 Abdel-Zaher, 2008; Jasinski, 2007). Froth flotation, a solid wettability based separation process is widely used in separation of phosphate rock and shown to be effective (Yehia et al., 1990; Singh et al., 1992; Elgillani and Abouzeid, 1993; Al-Fariss et al., 2013) .Poor selectivity and low recovery for micro-fine particles are hard issues in flotation of middle-low grade phosphate ore because Phosphate resources is becoming poor, fine and complex as the rich ores run out since the 1970s. The rapid depletion of high grade ores forces minerals industry to process low grade ores where finer grinding is required to achieve required liberation of the values, making the fine particle flotation inevitable. the performance of conventional flotation deteriorates rapidly as particle size decreases to below 10-20 µm, depending on the density of the particles (Feng and Aldrich, 1999). To date, fine particle flotation is still considered to be a challenge in mineral processing (Li et al., 2015) ."

Jan 1, 2016

By V. G. Papangelakis, G. A. Moldoveanu

"One of the major commercially viable secondary sources of rare earths elements (REE) are the ion-adsorption ores, containing 0.05-0.3 wt% rare earth oxides physically adsorbed on the surface of clay minerals formed during weathering of lanthanide-rich rocks. Although ion-adsorption deposits are substantially lower grade than other types of rare earth sources, this is offset by the easier mining and processing costs and the low content of radioactive elements. The conventional extraction route involves ion exchange leaching with monovalent cation solutions (usually ammonium sulphate) under ambient conditions; during the process, the lanthanides are desorbed and transferred into solution, being replaced by the exchange cation. While ammonium ions are known to perform best, there is increased environmental motivation to investigate alternative lixiviants in order to minimize ammonium sulphate impact via reducing its use without considerable loss in rare earth recovery.The objective of the present research was to screen various cations salts (alkaline and alkalineearth metals present as sulphates, chlorides and acetates, respectively) in order to comparatively evaluate lanthanide desorption levels and provide a theoretical base of the observed behaviour. The overall aim is to gain a better understanding of how both cation and anion may affect the overall REE recovery from ores in order to provide alternative processing routes. The distinct exchange capabilities of cations were explained in terms of differences in cation hydration enthalpy within the same group, i.e. Cs+ > NH4 + > K+ > Na+ > Li+ and Ba2+ > Ca2+ > Mg2+. For the same cation, it was determined that REE extraction efficiency follows the order sulphate > acetate > chloride, based on dissimilarities in constants of formation values. Various process implications scenarios will be described based on using mixed cations and anion matrices."

Jan 1, 2016

By Charles A. Stone, Eric C. Wang

"Top-down wall construction was selected to excavate the tunnel portal headwall areas of the ORB East End Crossing tunnel. Benefits included an expedited construction schedule realized by staging excavation and rock support with development of temporary construction access roads. Rock mass properties, proximity to right-of-way lines, and blasting impacts were considered to design suitable lift heights, intermediate bench locations, and permanent ground support systems to provide supported permanent excavations. Carbonate rock formations contained adverse subsurface geotechnical features including solution cavities, clay seams, weathered joints, pinnacled rock, and boulders, which were addressed by flexibility in design. The resulting over-break conditions and long-term water infiltration issues required economic design solutions. This paper discusses the unique considerations required during design of top-down tunnel portal headwalls excavated in carbonate rock formations including temporary excavation and permanent ground support systems which provided flexibility for unforeseen over-break, minimized construction delays, and provided long-term stability. PROJECT BACKGROUND The East End Crossing is an approximate 8-mile highway connection of the Louisville-Southern Indiana Ohio River Bridges East End Crossing (ORBEE) project. Currently under construction, this connection will link State Road 265 in Indiana with the Gene Snyder Freeway in Kentucky to form an outer loop bypassing the Louisville-Southern Indiana metropolitan area. This highway project features a 2,510-foot long, three-span cable-stayed bridge over the Ohio River, and a 1,680-foot long tunnel. The project, being managed by the Indiana Finance Authority and Indiana Department of Transportation, is scheduled to open to traffic by the end of 2016. The new twin three-lane tunnel under the historic Drumanard Estate requires steep cut excavations for approach and tunnel portal walls on the order of 60 feet deep through overburden soil and carbonate bedrock formations. This paper focuses on the design considerations for the permanent support of the top-down wall construction of the tunnel portal headwalls and approach retaining walls."

Jan 1, 2016

By N. Hiroyoshi, R. D. Corpuz, M. Ito, Hokkaido University, C. B. Tabelin, S. Veerawattananun

"Acid mine drainage (AMD), the very acidic and heavy metal-contaminated leachate generated when pyrite-bearing rocks are exposed to surface oxidizing conditions, is a serious environmental problem encountered after the closure of mines and mineral processing operations. In this study, we investigated the effects of soluble phases and metallic oxides, which are commonly found in strongly weathered pyritic wastes, on pyrite oxidation. Strongly weathered pyrite containing melanterite (FeSO4·7H2O) as the main soluble phase was obtained from Furikusa mine, Japan. The sample was washed using two methods to vary the relative amounts of melanterite in the sample. The effect of metallic oxides on pyrite oxidation was evaluated using ultrapure hematite suspensions. Our results showed that under acidic conditions, the effect of soluble salts on the oxidation of pyrite was stronger than hematite. More thorough washing of the sample resulted in the formation of an arsenic-bearing iron-oxyhydroxysulfate coating that minimized pyrite dissolution. This oxidized layer became relatively thicker and mechanically stronger when hematite was introduced after the more thorough removal of soluble salts. Characterization of this “coating” coupled with geochemical modeling suggest that it is most probably composed of two materials: schwertmannite and scorodite. Based on these results, a new approach to suppress pyrite oxidation by directly using iron-oxyhydroxysulfate as coating material is introduced.INTRODUCTION Acid mine drainage (AMD), the very acidic and heavy metals-contaminated leachate produced in closed/abandoned mine sites (Evangelou, 1995), mineral processing and coal cleaning tailings (Evangelou, 1995), and tunnel construction waste rocks (Tabelin and Igarashi, 2009, Tabelin et al., 2012), is one of the oldest and probably the most serious environmental problem of anthropogenic origin. When released to the environment, it rapidly pollutes river, soil and groundwater systems leading to the destruction of affected ecosystems. AMD is produced when pyrite (FeS2), one of the primary gangue minerals in sulfide ores and coals, is exposed to oxidizing conditions as illustrated by the following reactions:"

Jan 1, 2016

By EFFC/DFI Concrete Task Group

Concrete technology continues to advance rapidly and modern mixes with five components – cement, additions, aggregates, (chemical) admixtures and water – often have characteristics which differ significantly from the older three component mixes – cement, aggregates and water. Recent trends have favoured higher strength classes and lower water/cement ratios, resulting in greater dependence on admixtures to compensate for reduced workability and to meet the (often competing) demands for workability in the fresh state and setting time. The application of testing methods which reflect the true rheological properties of the concrete has not developed at the same rate as the mixes themselves and it is still not uncommon for the slump or flow table test to be used as the only acceptance test for fresh concrete.A joint review of problems in bored piles (drilled shafts) and diaphragm walls cast using tremie methods by both the European Federation of Foundation Contractors (EFFC) and the Deep Foundations Institute in the United States (DFI) identified a common issue. The review determined that many of the problems were caused by (or in part due to) the use of inadequate concrete mixes with inadequate workability, or insufficient stability or robustness of the mixes. It further identified the primary causes as inadequate concrete specifications and inadequate testing procedures. The consequences of these problems are often significant and it has been recognised that spending more time and money on getting the concrete right is the most cost effective approach.A joint Concrete Task Group was set up by EFFC and DFI in 2014 to look at this issue and this guide is the output from that Task Group. A research and development project, funded by the Sponsors of this guide, is being carried out by the Technical University of Munich in conjunction with the Missouri University of Science and Technology. This project includes desk studies, laboratory testing, and onsite testing at worksites in Europe and the US. The research work will be completed during 2016.

Jan 1, 2016

By Bowler Jonathan, Lorraine Kent, Tereza Crisu, Stuart Walker, Nicholas Lightfoot

"It has been the practice in Europe to extract the most economic seams first: taking the seams sequentially, top down, to avoid operating within the fractured strata formed by the subsidence trough above previously mined coal seams. In the 1990s, the UK coal industry found itself at a number of sites having to operate over one or more previously mined seams. This led to specific geotechnical challenges with respect to maintaining economic, safe and stable rectangular roadways with rock-bolted support.Within this paper, the current challenges and mitigation strategies of overmining in the UK are described following the completion of a -three-year European Commission-funded project in 2015. The challenges and mitigation strategies are related to:• A case study with overmining of older workings of variable geometry;• Numerical modeling for overmining layout and support design; and• A case study site planning mine layout when considering future overmining.INTRODUCTIONAt the first case study site, case histories were examined for a mine operating at a depth of approximately 700 meters where five longwall panels were extracted above workings 35-40 m below. The overmining of various extraction geometries below led to challenging conditions in areas of high vertical stress concentration. It was found that results from one longwall panel could be suitably used to predict behaviour in a subsequent panel. The experience was used to update previously existing guidelines on the positioning of roadways in relation to subsidence troughs. Existing guidelines recommended that only as a last resort should longwalls be planned to retreat over narrow pillars, or from solid ground into a subsidence trough. Existing guidelines regarding the layout of overmining panels are conservative, and new work indicates that such multi-seam geometries are possible with appropriate support management strategies."

Jan 1, 2016

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By Roger Storry, Donald Bruce, Arnaud Hochart

"INTRODUCTIONThe Port of Miami Tunnel (POMT), designed and constructed by Bouygues Civil Works Florida between 2009 and 2014, was a Public Private Partnership between the Miami Access Tunnel Concessionaire, Florida Department of Transport, Miami-Dade County and the City of Miami. The project comprises dual 11.3m internal diameter, 1.27km long, twin lane road tunnels running between Watson and Dodge islands and under the main shipping channel in Biscayne Bay (Figure 1).The POMT was a unique project which embodied many technical firsts and involved the first large diameter tunnels constructed through Florida’s challenging sedimentary carbonate strata. At the outset, a comprehensive ground investigation was performed, using both conventional and less conventional investigation techniques, to characterise the highly heterogeneous ground conditions.The findings of the investigation had a major impact on the tunnelling methods, triggering a series of mitigation works to ensure that the tunnels could be excavated safely and effectively. The mitigations included modifications to the already designed Tunnel Boring Machine (TBM), to facilitate an innovative excavation process, and a unique grouting campaign (Storry et. al. 2013a). The project was completed and opened to traffic in August, 2014 and has significantly alleviated traffic congestion in Downtown Miami.GEOLOGICAL CONTEXTThe geological conditions at the project site consist of carbonate sediments which can be divided into distinct geologic units; the Miami Limestone Formation (Layers S3, S4), the Fort Thompson Formation (Layer S5), the Anastasia Formation (Layer S6), the Key Largo Formation (Layer S7) and the Tamiami Formation (Layer S8). Multiple changes in sea level over a relatively short geologic time scale have resulted in a heterogeneous profile consisting of interbedded sedimentary rocks and sediments, which vary widely, both vertically and laterally (Figure 2)."

Jan 1, 2016

By Peter A. Adcock, Rob Fraser

Interest in monitoring nucleation overpotential in electrometallurgical processes dates back some 40 years or more. Conversely, remarkable progress has been made in recent years on describing in detail the processes involved in the formation of thin films by electrodeposition. The newer body of work underscores a need for greater clarity in speaking about the role of nucleation and in the acquisition and interpretation of nucleation overpotential measurements – the aim of this paper. In electrometallurgy, it is generally desirable to form deposits that remain smooth, compact, and relatively fine-grained while the deposit grows to a thickness on the order of 5-10 mm, about 100 times thicker than technological thin films. Hence, we distinguish two kinds of nucleation that can result in formation of new grains:- (1) initial nucleation (onto the substrate surface) of islands that coalesce into growing deposit, and (2) ongoing nucleation of new grains on the deposit surface long after the substrate has been covered and ceases to have a direct influence. Nucleation overpotential of the first type should be measured on an electrode surface truly representative of a real industrial substrate. The second type requires judicious choice of electrode material – an “ideal foreign substrate”. In general neither the industrial substrate nor native metal to be deposited is suitable for measurement of the second type of nucleation overpotential, because of interference by other processes. For the future, clear terminology is needed to distinguish these two types of nucleation potential. The second is the one for which the type of plot dubbed by Moats and Derrick as an “Adcock plot” and by us as a “Kerby-Adcock plot” was first conceived and correlated with relatively thick zinc electrodeposits. The data of Moats and Derrick showing trends for copper electrodeposition on stainless steel and on copper electrodes are interpreted within this framework.

Jan 1, 2016

By M. Ye. Shulgina, M. L. Bolotin, S. A. Prokopev, Ye. S. Prokopev

Iron ores concentration at Russia’s operations is carried out using conventional flow sheets. They comprise the two-four stage grinding followed by one-two stage magnetic separation. This results in the maximum recovery of magnetite to concentrate and the tailings generation. The final concentrate is generated only during the last stage of magnetic separation. Technologically, this flow sheet layout is not effective at recovering the liberated magnetite grains during grinding to the resulting concentrate. Advanced models of magnetic separators do not allow for the selective separation of the tailings and the portion of the resulting iron ore concentrate. Magnetic product which is the ore mixture of the liberated magnetite grains, high grade and low grade intergrowths is directed to the next grinding stage. In this case, regrinding of the liberated magnetite occurs. In addition, the performance of hydrocyclones during classification in closed grinding circuits is poor. Their classification efficiency does not provide the material separation in accordance with the size. In this case, simultaneous separation in accordance with the density occurs. The quartz particles with the size of 300 mm have similar velocity and trajectory like the particles of magnetite with the size of 60 mm. As a result, light and coarser intergrowths report to the overflow and free heavy magnetite grains report to underflow and return to regrinding (“the density effect”). This resulted in a significant increase of a mill circulating load, the decrease in the feed throughput and higher power consumption. In this connection, the development of iron ore concentrate stage recovery with the focus on gradual liberation of the intergrowths is getting much attention. Gravity concentration technique, particularly, spiral separation is effective at solving the problem of stage recovery not only the dump waste product but also high grade magnetite concentrates at the early concentration stages. This can be attributed to a significant difference in magnetite (4.9-5.2 g/cm3) and host minerals (quartz 2.7 g/cm3) densities, which is the principal during gravity concentration. The test work on concentration of various products samples from current operations (the mills discharges, concentrates from various stages of wet magnetic separation and cyclones underflows) was carried out. Spiral separators SV-500 and ShV-500 manufactured by Spirit LLC were used for the test work. High grade iron ore concentrate (69.05% Fe) was generated during primary wet magnetic separation concentrate concentration using a spiral separator. During the concentration of mills discharges the content of iron in the resulting concentrates and middlings of wet magnetic separation II stage was 64.5% and 64.6%, respectively. The recovery of iron to the concentrates of spiral separation was 33.6-42.0%. The studies presented demonstrate that by using spiral separation for iron-bearing ores concentration, you can separate magnetite liberated grains at the early concentration stages, decrease their regrinding and circulating loads in grinding circuits. This process is able to improve the overall recovery and economics of iron ores concentration process.

Jan 1, 2016

By N. V. Moraka

In dealing with transformational aspects, the South African Constitution aspires for a balance between attempts to broadly represent the country’s demographics in the way in which organizations are structured and the need to maintain the necessary skills to ensure continual retention of skills for optimum and efficient organizational performance. Through the Mining Charter, government aimed to redress gender and racial imbalances in the mining industry as part of transforming the demographic representation of mining companies to include black people, women, and people living with disabilities in all job levels up to top management. While the Constitution calls for an appropriate balance between demographic representation and competency, this aspiration for mining poses challenges for companies due to the proficient and competent skills needed in this industry. To this end, the South African mining industry has been subjected to substantial criticism from government regarding the slow progress of transformation. The mining industry justifies its slow pace of transformation by pointing at inconsistent, varying legislation and definitions governing transformation, limited skills available from historically disadvantaged groups, and cautioning not to compromise the sustainability of mining companies by marginalizing white males and white youth with the objective of addressing racial imbalances. This lack of understanding between industry and the government has led to considerable confusion regarding the accountability of stakeholders in transforming the industry. This article presents the perspectives of ten mining executives on transformation in the South African mining industry. The theoretical description of transformation, as well as other mining stakeholders’ interpretations of transformation. is presented. Qualitative data from interviews with mining executives demonstrates their understanding of transformation through rich descriptions, interpretations, and implications in their contexts. The findings demonstrate that transformation in the mining industry is not simply about race and gender, but about cultural change, a change in mind-sets, embracing diversity, equalizing rights and opportunities, and attaining social justice. Moreover, transformation is clearly a gradual process. The article concludes with a recommendation for the definition of transformation to be corroborated with the views of mining executives and that of the Constitution of South Africa. This will create an overarching, simplified definition of transformation that can be accepted and interpreted by all stakeholders.

Jan 1, 2016

By J. E. Dreier, R. E. Scheffel, A. Guzman

"This paper outlines a comprehensive, cost-effective testing program for the acid-ferric sulfate heap leaching of oxide, supergene and primary copper ores. It is based on extensive experience in copper heap leaching and uses the many technological advances in the field developed over the past several decades. The approach described requires firstly a detailed resource evaluation, then a hydrodynamic characterization of representative samples and, finally, a focused metallurgical testing program. The principles communicated here can be applied to other acid leachable minerals. The program varies considerably from conventional testing in its disciplined, orderly, step-by-step approach, its application of hydrological and chemical principles to leaching, and its reliance on fewer, more tightly controlled column tests. The purpose of the test program is to optimize the financial, time and other resources devoted to the program, while minimizing the financial risks to the development company or companies and the project funding providers. IntroductionThe major goal of any process development testing program should be the successful implementation of the project. With respect to heap leaching, the metallurgical testing program plays a critical role in the larger objective, as described in Scheffel (2013, 2014). McNulty’s series of papers (1998, 2004, 2014) confirm that the success of any project is directly proportional to the extent and quality of the testing program on which the process is designed.Therefore, a key development objective is to conduct a well-focused metallurgical test program. While the primary focus of this paper is copper, the acid leaching of any substance would benefit from a similar approach.This paper addresses primarily the sulfate system, which is compatible with the bioleaching of sulfide minerals. Nicol et al. (2011) described the advantages of the chloride leaching of copper sulfide minerals. United States patents Nos. US 2009/0173188 A1, US 8,597,933 B2 and US2015/0232963 A1, assigned to BHP Chile Inc. and BHP Billiton S.A. Ltd, describe methods for both the oxidative and nonoxidative leaching of primary and secondary copper sulfides. Reyes (2013) and Ipinza and Flaquer (2014) described commercial applications of chloride-based heap leaching. The testing disciplines discussed in this paper will also apply to the development of an acidic chloride leaching system."

Jan 1, 2016