Search Documents

By Davar Abi-Zadeh, Cillian Brown, Deepak Kandra

"Grout backfill strategy for a particular subsurface concrete tunnel (~4.9km long, 3.5m in diameter, carrying 20” gas pipeline) was based on achieving 1:100 slope of the fill in order to progressively fill the tunnel, in a series of 350m section. Grout rheology, particularly its non-Newtonian and thixotropic behavior, determines the final fill slope for given backfill strategy. The objective of this study was to simulate the two-phase grout mix backfill process using Computational Fluid Dynamics (CFD) and determine the slope of the fill to validate and optimize the backfill strategy. Three dimensional CFD study showed that for a 500m long tunnel section with a single injection point of grout, given its rheology, it will likely keep flowing without filling the 500m section height wise. Design optimization for filling was carried out using two dimensional studies to make the backfill process “slope independent” by incorporating a 2.5m high bulkhead at ~1,000m. INTRODUCTION As part of a gas field development a 20” onshore gas pipeline is required from the landfall site to the processing terminal some 8km inland. At the landfall site the gas pipeline is routed in a ~5km underground tunnel underneath a bay. For operational reasons and planning consents as well as to mitigate environmental impact based on an environmental impact study, once the gas pipeline and the associated services and spares have been installed, the subsurface gas tunnel will be fully grouted. There will be no permanent access to the tunnel after construction is completed and the site compounds have been reinstated once works are complete. One of the key requirements is that “full grouting of the tunnel” is desired. The grouting material used is a non-Newtonian and thixotropic fluid mixture of bentonite, cement, plasticizer, retarder/stabilizer and water. The tunnel is filled progressively in 350m sections using a combination of existing and new pipework assuming the grout rheology will yield a fill slope of 1:100 in a 350m section. The proposed grouting system used one pump at the grouting compound to pump the grout into the tunnel using the existing tunneling pipework. For the longer runs a second booster pump was used in series to pump the grout to its final discharge location. The filling process is controlled via a system of flow meters, pressure transmitters and a tunnel CCTV system."

Jan 1, 2016

By N. Katsikaros, N. S. ‘ Yap, B. Adaszynski

"Cyanide is a well proven, effective lixiviant that has been utilised for centuries in gold extraction processes. Despite being used in close to 90% of gold processing plants, cyanide leaching is still being scrutinised due to its toxic nature. With governments tightening the regulations on cyanide management, and recently erected sites situated closer to community and environment, leach waste and tailings treatment has become increasingly important. Gekko Systems has worked with engineering companies and directly with gold producers to provide technical services and supply complete modular cyanide destruction (detox) systems for plants leaching both run-of-mine ore and high sulphide gravity and flotation concentrates. Although similar in principle, the different materials presented unique challenges in design and implementation. Similar to designing any section of a processing plant, the development of the cyanide destruction plant design began with laboratory test work to simulate the full scale operation. This paper focusses on the laboratory test work and how other critical factors such as geographical location, logistics, and local community play a role in the process design and construction. Two design and supply cases are discussed in this paper; one treating intensive cyanidation concentrate leach tails and one treating whole ore CIL tails. Although these plants both use the SO2/O2 process, each presented different challenges in laboratory testing and plant design, resulting in variations in final implementation including reagent choice, oxygen supply, and process control.INTRODUCTIONSince 1887, cyanide has played a large part in the beneficiation of gold from gold bearing ores. Cyanide is used to solubilise gold into solution, and is typically added in excess to maintain the leaching process. Some or all the excess cyanide can often be recovered and reused in the process however chemical destruction of cyanide is often necessary to manage cyanide levels in the tailings storage facility (TSF)."

Jan 1, 2016

"Geoscan is used for multi-elemental analysis of conveyed bulk materials in the minerals industry with proven performance and demonstrated paybacks of weeks or months in iron ore, manganese, copper, zinc-lead and phosphate industries. Geoscan-M measures continuously through the full bed depth and is unaffected by belt speed, particle size, layering, mineralogy and dust levels. Increments of typically two minutes are accurately measured and provide the plant operators with tonnage weighted results of contained elements. Measurement of the composition in real time enables prompt feedback to the mining operators and also feed forward to the process operators. Crushed ore increments can be diverted based on composition, such as diverting waste for disposal or marginal material to a stockpile for separate processing. Bulk sorting allows material to be placed into relevant stockpiles for subsequent blending to achieve consistency for process feed. Parameters used for decisions may be primary metal content, deleterious component content, other process parameter, or a combination of these. Process parameter may be the elemental ratio between critical components, e.g. Cu:S ratio, basicity, or the content of an “indicator” element (such as Si indicating material hardness). Benefits will be discussed based on case studies in copper and iron ore.IntroductionAs operators of process plants strive to remain competitive as capital and operating costs increase and commodity prices fluctuate, more focus has been directed at incremental performance improvements at incremental cost rather than major expansions to increase output. The philosophy of working smarter allows plants to adopt technologies proven in other industry sectors to minimise risk. This paper discusses one such technology that the minerals sector is adopting and has found to be safe, reliable and accurate with paybacks of weeks in most applications. New applications continue to be found and major benefits realised at various stages in the processing and handling of ores and products."

Jan 1, 2016

By Luis Valentim, John E. Wiegand

Highwall or face profiling has long been used to facilitate the design and placement of front row blastholes to ensure optimum burdens. Traditionally, a large number of laser measurement points obtained from the rock face or highwall, were input in profiling software packages. This method can be time consuming and requires access to the rock face with a complete view of the highwall, to be successful. Stereo photography has also been used to generate the rock face surface, but this method also requires access to the highwall (and pit floor in some instances) for measurement of reference targets or points.

Jan 1, 2016

By Pierre De Pasquale, Gilles Jauffret, Ricardo Chavez

"When blasting in quarries or mines, the main source of inconsistent results is directly related to thenon-homogeneous energy distribution through the rock-mass volume. This variation has differentorigins: drilling deviations, geometry differences from one borehole to another (burden, spacing ...),and inherent geological conditions."

Jan 1, 2016

By Elisabeth Tønnesen, Lloyd Tunbridge

"SUMMARY Injection grouting in rock around tunnels is used to reduce or stop water inflow. Little is known about the distribution of pressure within the rock mass during and after grouting. Instrumentation was developed to record pressure at the back of the packers inside the rock mass during injection grouting in order to improve our understanding of the process. Using this equipment measurements inside multiple injection holes during injection pumping have been made during several rounds of injection grouting in a tunnel. The data has been compared to the data recorded on the grout pumping rig and analysed to gain an understanding of the behaviour of grout injection process in the rock mass. The initial results are reported in this paper. INTRODUCTION Construction of a tunnel in soil or rock below the ground water table frequently results in the flow of ground water into the tunnel if the ground is permeable or fractures conductive. The injection of cement or chemical based grouts is frequently used during tunnel construction to reduce flow of water into a tunnel. Significant water flow into a tunnel is undesirable for several reasons: • there is a high cost in pumping out water over the lifetime of a tunnel; • drips and flows of water have to be diverted from the roadway or track; • where freezing conditions occur there is the possibility of ice build up and; • ground water levels may be changed possibly affecting surface water such as causing drainage of lakes and ponds, and changes in vegetation. Grout injection is most effectively done ahead of excavation to ensure that the grout penetrates the ground. Where heavy flows of water already occur into a tunnel the grout may be washed out before it sets. Normal practice in ground where water flows are encountered is to inject grout in a number of long holes ahead of the face with outer holes forming a ring around the proposed tunnel excavation – eventually forming a shield of grouted rock around the final tunnel, Figure 1. The holes may be sealed off a couple of metres into the rock with an expandable rubber plug around a pipe through which the grout can be injected, Figure 2. A one-way valve in the plug stops the grout from flowing back out of the hole when pumping stops and avoids grout flowing out through neighbouring holes. The rubber packer with a one-way valve permanently installed in the injection hole precludes the measurement of pressure down the hole when pumping is stopped."

Jan 1, 2016

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By Vishwajeet Ahuja, Benoit Jones

"INTRODUCTION Shotcrete lining forms an integral part of conventional tunneling and is widely applied for underground excavations. Early strength gain of the shotcrete is a crucial aspect for ground support and safety of operatives. Strength requirements are dependent on various factors such as lining thickness, ground type, excavation size and tunnel depth. The early strength gain is typically monitored using destructive tests, such as needle penetration, stud driving or coring samples for uniaxial compressive strength testing in the laboratory. Being destructive, these tests cannot be directly performed onto the lining without causing damage that must be repaired, which is a particular problem for permanent linings. For this reason and to avoid the need for operatives to work near to exposed ground and/or fresh shotcrete, these destructive tests are often performed on panels, which are sprayed at the same time as the tunnel lining. All current testing methods are also very local, testing only a small part of the lining or a panel, which may not be representative because the temperature history could be significantly different. Therefore, these tests do not provide an accurate or complete picture of the lining strength gain. New testing methods that are non-destructive and can scan the whole lining remotely would be extremely desirable. This paper describes a new method, using thermal imaging techniques, that achieves these aims. It also discusses the real-time on-site application of the method, providing insight into the experience gained and conclusions derived. Shotcrete Shotcrete used for tunnel linings requires immediate strength development. The strength development is a direct result of the hydration reaction of cementitious materials present in it. A progressive sequence of the hydration reaction changes it from a solid suspension (typically referred to as fresh concrete) to a solid skeleton with a porous network and thereafter, into a solid with predominantly discontinuous pores (Byfors 1980). In the case of shotcrete, early strength is needed to support the self-weight and then continuing early age strength gain is required to begin to support ground loads. These strength requirements, along with other workability needs, are met by careful concrete mix design, the use of admixtures, such as accelerator and superplasticizer (BS EN 934-5 2007), and supplementary cementitious materials, such as silica fume."

Jan 1, 2016

By P. T. Bissert, J. P. Ducarme, J. L. Carr, A. K. Smith

"The continuous mining machine is a key piece of equipment used in underground coal mining operations. Over the past several decades these machines have been involved in a number of mine worker fatalities. Proximity detection systems have been developed to avert hazards associated with operating continuous mining machines. Incorporating intelligent design into proximity detection systems allows workers greater freedom to position themselves to see visual cues or avoid other hazards such as haulage equipment or unsupported roof or ribs. However, intelligent systems must be as safe as conventional proximity detection systems. An evaluation of the 39 fatal accidents for which the Mine Safety and Health Administration has published fatality investigation reports was conducted to determine whether the accident may have been prevented by conventional or intelligent proximity. Multiple zone configurations for the intelligent systems were studied to determine how system performance might be affected by the zone configuration. Researchers found that 32 of the 39 fatalities (82%) may have been prevented by both conventional and intelligent proximity systems. These results indicate that, by properly configuring the zones of an intelligent proximity detection system, equivalent protection to a conventional system is possible. INTRODUCTION Underground coal miners are exposed to a variety of hazards on a daily basis. Among coal and rock dust exposure, high noise levels, roof and rib falls, and the potential for fires and explosions, operating and working with heavy machinery poses a significant risk to miner safety. One of the most hazardous jobs is operating or working nearby a continuous mining machine (CMM). According to Mine Safety and Health Administration (MSHA) statistics, 39 miners have been fatally struck or pinned by a CMM since 1984. In an effort to prevent future striking and pinning fatalities from occurring, proximity detection systems have been developed and are now required on all operating CMMs in underground coal mines with the exception of full-face CMMs [1]. Commercially available proximity detection (cPD) systems are based on the principle of magnetic flux density (B-field). Typically, four magnetic field generators are positioned on a CMM, and personal alarm devices (PADs) are worn by the miners that detect magnetic flux density difference. As a miner wearing a PAD gets closer to the machine, the flux density increases. Zones can be constructed around the machine so that an alarm will trigger on the PAD based on the flux density."

Jan 1, 2016

By Kevin Green, Iván Contreras, Aaron Grosser, Jon Ausdemore, Rachel Leier, Amr Ragy

"Construction of a new tailings dam was required to increase tailings storage capacity at a trona mine near Green River, Wyoming. The new dam was founded on overburden soils underlain by both fractured and competent bedrock. The stored tailings and water had high salt content, resulting in salty seepage water. To reduce the impact of the salty water on groundwater and the Green River, the design of the new tailings dam included a 257,260 SF (23,900 m2) seepage cutoff extending into competent rock.An extensive subsurface characterization was performed prior to completing the design and suitable seepage cutoff methods were evaluated. The approach selected was a full replacement panel using hydromill and clamshell for construction and self-hardening slurry (SHS) for the wall material. Laboratory testing was performed and ongoing monitoring has continued to evaluate the hydraulic conductivity and seepage cutoff performance in the briny environment.The paper includes project background, the collaborative approach and outcomes of the QA/QC program, and the monitoring results for the seepage cutoff wall.PROJECT BACKGROUNDCiner Wyoming, LLC (formerly OCI Wyoming, LLC) owns and operates the Big Island Mine facility near Green River, Wyoming. This underground trona mine has produced soda ash since 1962. The Greater Green River Basin covers much of southwestern Wyoming and extends into northeastern Utah and northwestern Colorado. The Ciner facility is located in the Green River Basin, which is part of the Wyoming Basin physiographic province. The Green River runs to the west and the south of the Ciner facility.Beginning in the early 1990s, Ciner primarily disposed tailings underground in mined-out panels. However, in recent years, underground storage has become limited and some disposal has transitioned to the ground surface. Long-term planning revealed a need to expand Ciner’s surface tailings disposal capabilities. Pond 2, a previously permitted disposal area, was identified as the most viable location for a storage facility. The Pond 2 site is directly north of the Ciner plant facilities, northwest of the active Upper Delta tailings storage facility, and northeast of the Green River (Fig 1)."

Jan 1, 2016

By Jhon F. Chávez

"El presente texto describe las técnicas de análisis, diseño y optimización de las mallas de sostenimiento activo, de forma que optimiza las condiciones de seguridad y reducción de costos de sostenimiento en las labores de la minera Iscaycruz, así como los sobrecostos por daños a instalaciones y equipos por accidentes relacionados a falla en el sostenimiento activo."

Jan 1, 2016

By A. Taghavi, I. Hassan, A. Solecki

"The Eglinton Crosstown Light Rail (LRT) Project is part of an $8.4 billion investment to expand transit in the Toronto, Canada area and is the largest transit project initiated in Province’s history. Settlement control and impact to over 1400 adjacent structures due to tunnelling was identified early as a critical project risk. The ground conditions along the 10km tunnel alignment consist of water bearing soft ground deposits (clays, sands, silts) which required careful analysis and control during design and construction. This paper will describe the process used to analyze settlements along the numerous of adjacent structures and evaluate achieved settlement results to those used during design. The paper will demonstrate that with the appropriate design specifications, selection of modernized EPB machines, and contractor performance, settlement can be maintained well below typical industry (volume loss) standards, expanding the application and suitability of soft ground tunnelling in sensitive settlement areas. INTRODUCTION The Eglinton Crosstown Light Rail Transit (LRT) Project is part of an $8.4 billion (2010$ CND) investment from the Ontario provincial government to expand transit in the Toronto, Canada area. The project is being developed by Metrolinx, an agency of the Government of Ontario to provide 19 kilometers of dedicated LRT service connecting the City of Toronto from the west to east along Eglinton Avenue. Upon completion in the year 2020, the Crosstown will be the first LRT constructed in Toronto. It will link regional and local transit, cut travel time along the route by half and provide over a thousand jobs during construction."

Jan 1, 2016

By R. Wirth, B. Orberger, C. Wagner, A. Tudryn, B. Baptiste, S. Miska, Université Paris-Sud

Banded iron formations (BIFs) comprise complex textures and mineralogy, which result from fluid-rock interactions related to high and low temperature alteration. The initial iron oxy hydroxide mineralogy and associated phases such as carbonates, quartz, apatite and phyllosilicates were transformed leading to an upgrading of these BIFs into the world’s largest source of iron ore. In low-grade BIFs, a large part of the iron is related to micro- and nano- metric iron-bearing inclusions within micrometric quartz and/or carbonates (mainly dolomite). We studied laminated jaspilitic BIF samples from a drill core containing 26.71 wt.% total iron, 0.2 wt.% SiO2, 0.32 wt.% MnO, 15.46 wt.% MgO, 22.32 wt.% CaO, 0.09 wt.% P2O5, < 0.05 wt.% Al2O3, 0.15 wt.% H2O and 34.08 wt.% CO2 (Aguas Claras Mine, Quadrilatero Ferrifero, Brazil). Bright rose coloured dolomite and quartz bands alternate with massive specular hematite bands. Raman spectroscopy, X-ray diffraction and FIB-TEM analyses reveal that the micro- and nanometric inclusions in dolomite are mainly hematite and minor goethite, partly occurring as clusters in voids. Curie Balance analyses were carried out at different heating steps and temperatures on whole rock samples and a synthetic mix of decarbonated sample and pure dolomite. X-ray diffraction on the products of the heating experiments shows that that hematite is stable and new phases: magnesioferrite (MgFe2O4), lime (CaO), periclase (MgO), portlandite (Ca(OH)2) and srebrodoskite (Ca2Fe2O5) were formed between 680°C and 920°C. These finding gives hints to optimizing the beneficiation process, as the presence of hydroxyl ions bearing goethite micro- and nanoinclusions lowers the sintering temperature. Prior separation of coarse hematite and barren dolomite and quartz, followed by lower temperature sintering of the inclusionbearing dolomite/quartz leads to transformations into phases with higher magnetic susceptibilities (such as hematite and magnesioferrite). The entire Fe and Fe/Mg oxide feed (the priorly separated fraction added to the sintered fraction) can then pass through wet-high intensity magnetic separation after crushing.

Jan 1, 2016

By J. Álvarez, J. Mesías, C. O. Gómez

"Operations routinely run flotation tests in laboratory mechanical cells to determine adjustments to plant operation based on feed flotation response or the effect of new reagents and dosages. The metallurgical results of these tests are certainly affected by changes in bubble size, which simultaneously impact the recoveries of the collection and froth zones. It is known that bubble size depends on the characteristics and operation of the machine in use, particularly on the gas flow rate delivered to the unit and the selected frother type and dosage. Although flotation rate constants have been related to bubble size, bubble surface area flux seems to be a more fitting variable to correlate flotation kinetics and cell performance, as it integrates bubble size and superficial gas velocity effects. However, although some evidence has been provided, a categorical relationship between cell recovery and bubble surface area flux has not been established. Our interest is to demonstrate this relationship to use it as a basis for developing soft sensors to track on-line collection zone recovery in cells. Flotation tests were designed to produce Cu concentrates for a range of bubble surface area flux values, obtained through changes in frother concentration at a constant gas flow rate, and by increasing gas flow rate at the same frother concentration. The tests were run on samples prepared from an ore batch supplied by a local operation, following strict grinding and flotation procedures, with a shallow froth to approximate cell recovery to that in the collection zone. Bubble sizes were determined using the sampling-for-imaging technique developed at McGill. The results unequivocally showed a consistent positive correlation between cell recovery and bubble surface area flux, and significant variations in performance when frother addition and gas flow rate were changed.INTRODUCTIONMineral flotation is a separation process to produce concentrates of valuable minerals by selective attachment of particles to the surface of bubbles. The process is carried out in machines where air is injected through a mineral pulp to form bubbles, and operated to create two zones: a bottom one (collection zone) where bubbles are continuously generated under conditions adequate to form bubble-particle aggregates by collision of the rising bubbles with suspended particles; and a top one (froth zone) where bubbles and bubble-particle aggregates continue to rise while concentrating and forming a froth layer for water and entrained particles to drain back to the collection zone, before overflowing as a concentrate stream. The phenomena occurring in these zones are complex and, in many cases, interactive, as they simultaneously affect stages of the particle separation sequence occurring in both zones. Although there have been significant advances in instrumentation to characterize particle and bubble populations, these have not resulted in knowledge to explain or models to describe phenomena from fundamental principles. Measurements continue to be limited to the development of empirical models for predicting the effect of operating variables on performance."

Jan 1, 2016

By Olli Haavisto, Lauri Koresaar, Navid Khajehzadeh

In recent times sustainable minerals processing is an important topic in research. Sustainable mining is linked with efficient use of energy and human resource in all process stages including beneficiation of the ore. Controlling and optimizing the recovery while preserving the grade of the concentrate is extremely important in flotation plants. This development requires new technological solutions and has given rise to the multitude of application areas for lasers. X-ray Fluorescence (XRF) and Laser-Induced Breakdown Spectroscopy (LIBS) are currently two of the predominant non-contact and direct analysing methods in industry. LIBS and XRF measurement techniques both have high capabilities for measuring elements. LIBS has a very simple and easy-to-implement spectroscopic setup, wider range of elements can be detected with online LIBS and measuring light elements is simpler by LIBS compared with XRF. It is of great interest to extract mineralogical information from the elemental results with no modification on the measurement setup. In order to achieve this, more advanced interpretation of the elemental peaks of LIBS spectra is required. Therefore, the major focus of this research is about measuring mineral concentrations from the elemental lines of LIBS spectra using advanced statistical methods. This accomplishment provides knowledge about mineral concentrations from the real-time assay data of the slurry LIBS analyzer. Consequently, this paper first discusses an analytical method called partial least squares regression leading to rapid mineral identification from the elemental contents of the LIBS technique. Then the technique is employed to analyze the mineral contents quantitatively through the information acquired from an on-stream LIBS slurry analyser. This can lead to many benefits such as rapid control of concentrate quality, enhanced recovery, saving time, energy and manpower.

Jan 1, 2016

By Grant Small, Jessica Kinal, Christopher J. Greet

"The conversion from an electrochemically reactive grinding media (forged steel) to a more electrochemically inert alloy (high chrome white iron) not only reduces the wear rate of the grinding media, but also has an impact on the grinding chemistry. Typically the grinding chemistry becomes more oxidising, with less reducing Eh values and more dissolved oxygen in the pulp. There is also a decrease in the EDTA extractable iron, which is an indication of the change in the media corrosion. These changes are indicative of alterations in the surface chemistry of the minerals that the operator is trying to separate. For porphyry copper ores the changes in the pulp and surface chemistry not only affect the copper sulphide minerals, but also impact the iron sulphides (i.e. pyrite and pyrrhotite). Generally, with more oxidising pulp chemical conditions during grinding there is an increase in the oxidation of the iron sulphides which renders their surfaces hydrophilic, thereby depressing flotation. This leads to improved selectivity for copper sulphides against iron sulphides.INTRODUCTIONPorphyry copper deposits are the dominant source of copper that is mined today to satisfy global demand. These style of deposits typically contain one percent copper mostly as chalcopyrite, but may contain other copper bearing minerals (for example, bornite, chalcocite, azurite, malachite), small quantities of pyrite and quartz. Porphyry copper deposits also contain economically significant quantities of gold, silver and molybdenum. Interestingly, the majority of the world’s porphyry copper deposits are concentrated along tectonic plate boundaries (Figure 1)."

Jan 1, 2016

By Kazutoshi Haga, Batnasan Altansukh, Yasushi Takasaki, Mohd Yazid Bin Abdul Razak, Atsushi Shibayama

"In this study, the volatilization behaviour of arsenic (As) and antimony (Sb) from arsenicantimony bearing minerals such as tennantite (Cu12As4S13)/tetrahedrite (Cu12Sb4S13) in copper ore was investigated using a roasting process. Specifically, the thermal decomposition of tennantite and the arsenic volatilization were investigated under nitrogen and air atmosphere. The roasting experiments were performed at temperatures ranging from 500 to 1,200oC and different retention times using a laboratory electric furnace. The results indicated that over 95% volatilization was achieved at 700oC. On the other hand, when the temperature increased to 1,200oC, volatilization rate of Sb reached to 90%. Therefore, volatilization of Sb requires high temperature compared to As. It suggests that As and Sb can be separated using temperature difference. Selective removal of As is possible at 700oC, subsequently Sb can be recovered as a volatilized product by increasing the temperature to 1,200oC. Meanwhile, volatilization of Cu and Fe was not observed on these conditions. The content of As and Sb in the residues obtained from roasting at 700 and 1,200oC was less than 0.3 and 0.75 mass%, respectively. The Cu content in solid residue at 1,200oC increased to 34 mass%. The clean copper concentrate with lower amounts of arsenic and antimony was obtained from the process. INTRODUCTIONRecently, arsenic (As) and antimony (Sb) contents in copper (Cu) concentrates are increasing year by year. Arsenic and antimony are present with Cu minerals such as enargite (Cu3AsS4), tennantite (Cu12As4S13) and tetrahedrite (Cu12Sb4S13) that associate with copper sulfides [chalcopyrite (CuFeS2) and bornite (Cu5FeS4)]. They are normally concentrated by flotation and treated in copper smelters. However, treatment of copper concentrates containing high amounts of arsenic and antimony by a smelting process is difficult due to environmental implications of toxic arsenic and antimony. As demand for copper continues to grow, the need to source copper from several types of resources including those that contain high levels of As/Sb becomes necessary. Therefore, a novel processes for the treatment of As/Sb bearing Cu concentrates are required. Reviews on copper resources such as enargite, tennantite and tetrahedrite containing high amounts of arsenic and antimony are covered widely in literatures by many researchers (Padilla et al., 1998; Welham, 2001; Vinals et al., 2003; Guo & Yen, 2005; Balaž & Achimovicova, 2006a; Filippou et al., 2007; Mihajlovic et al., 2007; Lattanzi et al., 2008)."

Jan 1, 2016

By Mark F. Sindelar, Yi Luo, Hua Jiang, Michael T. Shook

"Convergence of roof and floor in underground mine openings is a common occurrence. This convergence not only adversely affects the ability of workers, equipment and supplies to travel through the mine, it also reduces the effectiveness of the mine ventilation system, which is essential for the dilution of methane gas and airborne respirable dust. While installing secondary standing supports to control floor and roof convergence, such supports, by nature, partially obstruct a portion of the airway. These added obstructions inhibit the ability of the ventilation system to operate as efficiently as it could by increasing the resistance in and reducing the cross-sectional area of the airway.This study introduces and demonstrates the benefits of The Eye CAN™ standing roof support, which controls floor and roof convergence and is less obstructive to air flow than conventional wooden cribs. Laboratory findings show that the normal resistance of a supported lined airway is reduced by using this new product from Burrell Mining Products, Inc., while providing the same roof support characteristics of an established product-The CAN®. Load vs. displacement curves generated from laboratory tests demonstrated that this new product behaves with the same roof support characteristics as others in The CAN product family. Ventilation data gathered from a simulated mine entry was then used for computational fluid dynamics (CFD) modeling. The CFD analysis showed an improvement with The Eye CAN versus other accepted forms of standing roof support.This proof-of-concept study suggests that, when using this new product made by Burrell Mining Products, Inc., not only will the convergence from the roof and floor be controlled, but airway resistance will also be reduced.INTRODUCTIONOne of the basic elements of underground mining is the necessity to support the mine roof. It is well-known that easier reserves have been mined so that today's underground mines present challenging conditions. Factors influencing roof support decisions include mine depth, mining method, overburden composition, and agency regulations. Mining engineers, therefore, have to balance three objectives: safety, engineering, and cost. While safety is obviously paramount, and engineering often complements safety, the cost effectiveness of any product, method, or device warrants additional consideration in today's harsh business climate. Avenues for adaptation and improvement are found at the intersection of the three objectives."

Jan 1, 2016

By Sylvie Lévesque, Frederic Couët, Laura Pérez-Barnuevo, Cory Hennessey

Determining mineralogical characteristics of samples throughout the iron ore concentration process – from drill core samples up to the concentrate – is critical to process improvement and remediation. However, assessment of mineral proportions, liberation, and texture, although essential, can be time-consuming and costly. Thus, a mineralogical study is often not performed or only restricted to a limited number of samples. New iron ore deposits or new ore zones in active mines will bring new challenges as they are known to be problematic due to their lower grades, complex textures and presence of mineral impurities. In those cases, applied process mineralogy will be necessary to understand and to diagnose potential processing issues. To take full advantage of mineralogical information along the iron ore concentration process, new tools are being developed to provide mineralogical data based on texture, composition and liberation. In an early stage at the mine, the automated identification of drill core textures could provide essential information for the prediction of ore concentrability and grindability. In a later stage, the automated modal tool, combining the knowledge of the iron ore mineralogy of a specific deposit and the results of chemical analyses, can quantify the mineral proportions of the ore; results show good agreement between mineral estimation via chemical analysis and modal analysis using a Mineral Liberation Analyser. A bulk mineralogical analyser allowing semi-quantitative evaluation of the liberation of iron oxides is being validated. The results from the bulk mineralogical analyser will eventually be linked with the mineral proportions issued by the automated modal tool to provide complete mineralogical characteristics of iron ore samples. Ultimately, these mineralogical tools could provide valuable and timely insight for predicting concentrators’ performances or troubleshooting gravity separation processes.

Jan 1, 2016

By T. R. Ley

"INTRODUCTION Brutally honest mining executives will tell you that “safety is job #1 but.. dollars are also extremely important”. When economic times are tough, as they are now in mining, it can feel like you need to choose between safety and cost control. Leading edge companies know that it is excellence at both that provides the best performance. FLUID POWER SYSTEMS Fluid power systems are ubiquitous in mining – longwall systems, continuous miners, drills, haul trucks and excavators, etc. And fluid power systems are getting more powerful and using higher pressures to move greater volumes and achieve higher productivity. Average operating pressures in mobile equipment has been rising to 450 bar (6,500 psi) over the last decade. With increased system pressure comes ever increasing levels of stored energy. Stored energy that, if released in an uncontrolled fashion, can do tremendous harm to people and things.Fluid power systems are composed of pipe, flexible hoses, pumps, valves and actuators. They are filled with fluid (mineral oil or fire-resistant) to transmit power to where it’s needed for performing work. With time and use fittings can loosen, component performance diminishes and hoses wear and tear. In hostile environments, like coal mining, hydraulic hoses can fail in as little as 2 years according to DGUV (umbrella association of German Accident Insurers), maybe sooner in some particularly challenging environments. FLUID POWER SYSTEM SAFETY While appearing simple and benign on the surface, fluid power systems, particularly such systems on mobile equipment, have many potential hazards. Hazards that most workers aren’t aware of – particularly young, new hires. And those hazards that can quickly turn deadly. During the past couple of years, including at last year’s SME Conference, I talked to a wide variety of mining people about high pressure fluid injection injuries. Some people, often with little or no field experience, never heard of it. But, people with mine operations / maintenance experience were almost always aware of such injuries.Some had even seen it happen right in front of them. But most claimed it didn’t happen all that often. It just wasn’t seen as a problem!"

Jan 1, 2016