Search Documents

By Yuanfei Chen, Jianfeng Zha

"China is the largest producer and consumer of coal in the world. The mining-induced surface subsidence has bad influences on the surface and structures above the surface. In order to minimize disasters, removal, reinforcement, or maintenance structures are often adopted. In the application of maintenance methods, it is necessary to carry out dynamic surface subsidence prediction to choose maintenance methods, optimize maintenance time, and evaluate the amounts of work. Time series methods and influence function methods are common for dynamic surface subsidence prediction, but the former is difficult to consider with underground mining conditions, and the latter has low prediction precision. Therefore, this paper develops a dynamic subsidence prediction model aided by field-measured data and realizes the model programming. The model could achieve high-precision prediction of dynamic surface deformation through optimizing the parameters in time by using field-measured data of surface subsidence. The research results of engineering cases show that, with the method of dynamic prediction, the standard error can be controlled in the range of 5%, greatly improving the accuracy of dynamic prediction of mining subsidence, which provides strong technical support for the maintenance and management of structures. INTRODUCTION With the rapid economic development and continued industrialization process, the demand for energy is growing in China. Today, China is one of the largest coal, oil, and gas consumers in the world. Coal consumption accounts for 47.7% of the total consumption in the world (Tian, 2016). In order to meet the demand for coal resources in the process of modernization, more and more coal mines carry out coal mining under villages, buildings, highways, and bodies of water. The mining-induced overlying strata and surface subsidence have bad effects on surface and on various structures (such as buildings, railways, highways, high-tension transmission lines) and could even cause various disasters (Williams et al., 1998; Bell et al., 2000; Doyle et al., 2002). Generally, methods, such as removal, reinforcement, or maintenance are taken to eliminate the adverse impacts (Kraatz, 1984; Bell and Genske, 2001; Wang, 1989). When reinforcement or maintenance is selected to remove bad effects, the proper maintenance methods must be chosen. In addition, maintenance time, as well as an evaluation of time it will take to do the work are necessary to predict the surface subsidence with high precision."

Jan 1, 2017

By Martin McKinnon, Guy Reed, Russell Frith

"It is arguable that the development of reinforcing roof bolting systems has largely stagnated in recent times, primarily due to the prevailing industry view that few, if any, further improvements can be made to what currently exists. However, this paper contends that reinforcing roof bolting systems can be further refined by considering both the specific manner by which horizontally bedded roof strata loses its natural self-supporting ability and the specific means by which reinforcing roof bolts act to promote or retain this natural self-supporting ability. The Australian coal industry insists on minimising bolt-hole diameter to maximise load transfer and on targeting full-encapsulation by any means necessary. This has led to a significant, albeit unintended, consequence in terms of overall roof bolting effectiveness, namely increased resin pressures during bolt installation and the associated potential for opening bedding planes that may have, otherwise, remained closed during the bolt installation process. Given that the natural self-supporting ability of roof strata is strongly linked to whether bedding planes are open or closed, logically, minimising resin pressures should be a significant benefit. This paper focuses primarily on three key issues that relate directly to the function of the roof bolting system itself: (i) the importance of proper resin mixing in the context of maximising load transfer strength and stiffness, (ii) the importance of minimising resin pressures developed during bolt installation, and (iii) the importance of maximising the effectiveness of the available bolt pre-tension. All mine operators should be invested in improving the individual effectiveness of each installed roof bolt, even by relatively small incremental amounts, so this is an important topic for discussion within the mining community."

Jan 1, 2017

By Bora Okumusoglu, Devon K. V. Mothersille

"AnchorTest is an innovative software package, specifically developed for tablets, that permits ground anchor test data assessment and management in real time. The solution has two components: a front-end tablet app runs on the Apple iPad platform, and a back-end Cloudbased system running on Amazon Web Services with an online cross-platform website, which can be accessed from any PC, tablet or even mobile smartphone. This tool provides full data analysis and data management capabilities and portability to create greater efficiency in the anchor testing process. AnchorTest is programmed to accommodate the major international anchor testing codes and incorporates an intuitive user interface, which is revolutionary compared to conventional engineering software designs. The use of this tool creates an environment where the testing of ground anchors has effectively become a paperless exercise with greater efficiency and access to instantaneous feedback on the performance of anchors in relation to established acceptance criteria.Historically, project personnel record and analyze the results from anchor load tests using spreadsheets and a laptop computer and/or on predesigned paperbased test sheets (usually as a backup of the testing). In addition, the processing of the test results is not typically performed in real time as the testing progresses — the calculations and analysis are performed either afterward while still on site (if a field office is available) or after returning to the office. Undoubtedly, on larger projects containing numerous anchors where multiple anchor tests may be performed at the same time, processing, analyzing and accepting the load test data and results can be especially time consuming, which could cause delays to the construction schedule.DevelopmentThe need for a more automated and digitized approach to record, process and analyze the data from anchor load tests was highlighted at a deep basement project for a mixed-use development complex in Moscow, Russia. The diaphragm wall supporting the structure was approximately 1,970 ft (600 m) in perimeter length and about 148 ft (45 m) deep, with an excavated depth of about 82 ft (25 m), which required six levels of single bore multiple anchors (SBMAs). This project provided a challenge to recording, processing and signing off on the data generated from some 3,600 3-unit SBMAs. More specifically, for this project, three hydraulically synchronized stressing jacks were used to stress and proof test each 3-unit SBMA, which resulted in nearly 10,800 data plots of the load-extension tests being generated. This project served as the main impetus in the conceptual design and optimization of AnchorTest."

Jan 1, 2017

By Zbigniew Lubosik, Andrzej Walentek, Stanislaw Prusek, Sylwester Rajwa, Aleksander Wrana

"Underground coal gasification (UCG) provides a solution to supply electricity from high ash coal or deep deposited seams. The coal is consumed in situ, and, accordingly, the ash is left underground. UCG could play a major role in the future of coal, which is expected to fuel 44% of the world’s energy in 2030, in a more environmentally friendly and commercially viable manner. Nevertheless, it is known that the UCG can impact the environment. One of the most important factors in safe UCG process should be the evaluation of rock mass quality and the monitoring of its behaviour. The changes of rock mass parameters and quality have an influence on numerous aspects, such as subsidence and the stability of underground workings in georeactor vicinity, however, they also increase the possibility of pollutant migration through fractures and pores. These issues are especially important in cases of gasification conducted in an operating mine or on areas of high ecological vulnerability. This paper details observations made in two underground trials of UCG performed in Poland recently. The first of which is the Experimental Mine Barbara (under the project entitled HUGE-2 Hydrogen oriented underground coal gasification for Europe – Environmental and Safety aspects, (Wiatowski et al., 2015). The other trial has been conducted at an operating mine, Wieczorek, which is in the framework of a research project on the development of coal gasification technology for highly efficient fuel and electricity production (Czaplicka-Kolarz et al., 2013). During these trials, investigations were carried out aimed at assessing geomechanical parameters of rock mass and support behaviour in surroundings of UCG geaoreactors. Investigation comprises assessment of geomechanical parameters of coal, floor and roof strata, roof displacements, and concrete support strength parameters variation, as well as standing steel support load. Hydraulic penetrometer, endoscopic camera, Schmidt hammer, pull-out method, telltale, and ground penetration radar (GPR) were used in the investigation. Research conducted at both EM Barbara and Wieczorek Collieries revealed that the UCG process did not adversely affected the competency of rock mass (expressed by number of fissures and strength parameters of rocks), the stability of roadways and the support performance in the areas located in the vicinity of the georeactors."

Jan 1, 2017

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By D. Sagara, V. G. Makhado

"A model based control strategy was implemented at Loulo Gold Mine in Mali, to stabilise the thickener underflow stream density. This stream acts as the feed to the leaching circuit. pH control of the leaching circuit was integrated with the model-based controller due to slow process dynamics that are not suited to PID control. The controller performance was quantified over a period of 6 months, and was compared to the performance before implementation. The model based controller reduced process variability for both thickener underflow density and pH considerably, and resulted in a reduction in flocculant and lime consumption of 9.32 and 6.55%, respectively. INTRODUCTION Reagent consumption in gold processing plants significantly contributes to the total operational costs. In a typical Carbon-in-pulp (CIP) circuit, the reagent consumption associated with leaching, adsorption, elution and regeneration contribute to approximately 15% of the total operational costs (Stange, 1999). At Loulo Gold Mine, the reagent consumption associated with leaching, adsorption, elution and regeneration contributes to 6% of the total operational costs. As such, a reduction in reagent consumption will present a significant opportunity for savings on operating expenditure. Variability in feed ore characteristics results in continuous changes in steady state operating regions, which presents process control challenges as a result of the long residence times in some of the process units associated with gold processing plants. Overdosing often occurs in the presence of process variability to ensure safe operation and to maintain recovery targets. As a means of reducing reagent consumption and accounting for significant changes in the feed to gold plants, some of the plants have resorted to improving their process control strategies around their circuits. This paper focuses on the implementation of a model predictive based controller at Loulo Gold Mine on their thickener and Carbon-in-leach (CIL) tank to: •,stabilise the thickener underflow density, and •,the CIL tank pH."

Jan 1, 2017

By J. Olson

"A model was developed to use near-infrared (NIR) analysis of pulverized ore samples to estimate the recoverable gold content for ores from the Barrick Cortez Hills underground mine. Current routing practices use a ratio of the cyanide soluble gold content and fire assayed gold (CN/FA) to classify ores as oxide or refractory. Prediction accuracy of the NIR model was equivalent to the CN/FA ratio. Prediction accuracy was improved by combining the CN/FA ratio and the NIR spectra. Bootstrap validation estimates the root-mean-square error to be 9.92% with an estimated r-squared value of 0.893. This model will allow more accurate estimates of the variability in recoverable gold content throughout this mine. These data will aid in building an improved geo-metallurgical model or in making better informed routing decisions during the production cycle.INTRODUCTION The contained gold of an ore available for cyanidation is often related to subtle variations in the mineralogy. It is difficult and expensive to collect enough mineralogical information in order to predict how the variable mineralogy will impact the metallurgical results and project economics throughout the life of the mine or mill. Near-infrared spectroscopy may be an effective tool to rapidly and inexpensively collect discrete, quantitative mineralogical data for minerals that contain transition metal oxides, metal sulfides with semi-conduction properties, rare earth metals, and some chemical groups having di-pole covalent bonds such as carbonates, sulfates, and various types of clays (Hunt, 1977). Near-infrared spectroscopy can be a powerful tool for geo-metallurgical characterization of deposits where the presence of these minerals has direct or indirect relationships to metallurgical results such as grindability, regent consumption, or recovery. Near infrared spectroscopy is a rapid analysis that measures the intensity of reflected light in the near-infrared spectrum. The ranges for the ASD-Panalytical units used in this study extend through the visible spectrum and into part of the UV spectrum, reporting reflection by wavelength from between 350 nm to 2500 nm. Absorption peaks visible in this range are a result of interactions with outer valence elections or chemical bonds. The location and intensity of the peaks vary depending on the chemical composition and crystal structure of a solid indicating the presence and abundance certain minerals (Hunt, 1977; Clark, 1984)."

Jan 1, 2017

By Erik Vlot

"The mining industry has recognized the advantages of high density backfill or ‘paste’, which is typically pumped with a hydraulically driven piston pump. Due to the discontinuous flow of this type of pump, pressure pulsations can occur in the discharge line. Pressure pulsations are an undesired phenomenon in pumping installations for a number of reasons that include: damage to the pumping system; piping and supports; disturbing noise levels; and even safety risks for operators and maintenance personnel.This paper describes an advanced system on the GEHO® piston pumps, which will prevent virtually no pressure pulsations from occurring, rather than merely reducing the already existing pulsations.INTRODUCTIONThe first GEHO® hydraulically driven piston pump was developed in the mid-1970s. It was an industrial design pump designed to operate in the high-standard industrial environment with regards to operating hours per day, duties, maintenance and lifetime of the pump and spare parts. This type of pump has a proven track record and has been further developed for the type of applications that we are describing today. The special feature of this pump type is its ability to pump extremely viscous slurry with solids content of up to 90% by weight, at high pressures. Typically, in the mining industry, this pump is used for tailings transportation, with a focus on mine backfill and is often referred to as a paste pump.In the 1980’s the hydraulically driven piston pump made its entry into the application of mine backfill, thanks to the high discharge pressure capabilities enabling the mines to pump higher density (i.e. higher solids concentration) slurries and pastes over longer distances.Part of the ongoing development was (and still is) the increase in discharge pressure and flow capacity to comply with the ever growing demands for high power piston pumps. In line with the technological developments and increase in performance duties, the popularity of this pump type increased significantly and many other industrial applications have discovered the benefits of this pump type.Together with the increase in pump discharge pressures and flow capacities the effect of an undesired phenomenon also increased: the phenomenon of pressure pulsations. Before we explore this subject in more detail it is important to first understand the design and the characteristics of a hydraulically driven piston pump."

Jan 1, 2017

By Allan Herse

"The years following World War II were nation building years in Australia. Soldiers returned from the European and Asian theatres of war sparking a major infrastructure construction boom. Dams and highways were built to keep up with the growth of towns and cities, which were bursting at the seams, not just from the returning soldiers settling down with their families but also from the many waves of refugees from war torn areas around the globe.The demand for electricity generation and distribution required for the growing population sparked the expansion of the national power grid with new high-voltage transmission towers appearing across the landscape. However, with an original design life of 50 years, those transmission lines constructed in the 1950s are nearing, or are at the end of, their anticipated service life.In recent years, the Australian power distribution network has changed from a period of high construction activity in greenfield high-voltage lines to a period that is now focused on reducing cost and maintaining existing assets. Replacing aboveground structural members and electrical components is relatively simple even under live conditions. However, the replacement or repair of tower foundations, many of which are in remote locations, has been a problem that has caused difficulties for power utilities trying to operate on a budget while also avoiding costly and unpopular power outages. With thousands of miles of aging transmission lines needing life extension work, Piling & Civil Australia (PCA) has developed a patented system of upgrading the foundations with micropiles while under live-line conditions without requiring costly outages. The system is seen as revolutionary by power utilities, allowing the utilities to extend the life of their existing assets until demand increases to warrant the construction of a new line. PCA has been working on a potential solution with Powerlink Queensland for the past 5 years to develop a quick and cost-effective foundation replacement system that can extend the life of its existing asset base anywhere from an additional 5 years to 50 years.With design support from Quanta Subsurface, USA, PCA recently completed the foundation replacement of 26 lattice tower foundations in the Townsville region of North Queensland. Using a steel bracket (patent pending) to connect hollow bar micropiles to the lattice towers, the installation techniques that were developed enabled the micropiles to be installed within a tolerance of less than about 3/8 in (10 mm) through the existing steel grillage foundation while maintaining live line conditions. The project was an Australian first and a trial by Powerlink for wider use within its network, and it was delivered on time and within budget at one tenth of the cost of traditional methods."

Jan 1, 2017

By M. H. M. von Wielligh

"Brick manufacturers supply a variety of uniquely coloured facebricks to the building industry, which requires a high level of colour consistency in the products. Colour variation in bricks is influenced by the composition and consistency of the white clay raw material. By blending varieties of naturally occurring white clay the manufacturers produce a unique range of facebrick products. Homogeneity of the white clay raw materials mined at Lenasia is crucial for producing bricks of consistent colour. Geostatistical investigations of the major element distributions (SiO2, Al2O3, Fe2O3, and K2O) and loss on ignition (LoI) were conducted. An analysis of the spatial continuity of these variables followed by ordinary kriging indicated that the upper white clay layer at Lenasia is richer in K2O and Fe2O3 than the lower layer. Consistency in the colour of facebricks depends critically on careful management of the variability in the K2O and Fe2O3 content of the clays. The geostatistical approach to understanding the distribution of elements in the clay allows miners to construct clay stockpiles of consistent quality for feeding the brick-making process. Geostatistical investigation of the chemical contents in other clay domains within the deposit is recommended, and could be extended to all facebrick manufacturers to assist in improving the colour consistency of their products. IntroductionMost clay in South Africa is used in the manufacturing of tiles, pipes, bricks, whiteware, refractories, and pottery. Bricks are manufactured from a wide variety of clay types, the behaviour of which during firing depends critically on the the clay mineralogy and chemical composition, but this relationship not well understood (Stein, 1982). The variety among clay deposits is related to the different processes of formation (Deer, Howie, and Zussman, 1992). The geochemical composition of the clay can vary between layers and within the same layer in an individual deposit (Lurie, 1984). The properties of clay minerals are determined by their structures and the different combinations of silicate layers, cations, and hydroxyl ions (Kingery, Bowen, and Uhlmann, 1976). South African clays can be classified as either kaolinite or montmorillonite and are seldom found in a pure form (Lurie, 1984). Different clay minerals affect the drying, forming, firing behaviour, colour, and quality of the brick product in different ways. Laboratory tests (full physical analysis) can indicate the suitability of a clay for the manufacture of ceramic products. The minerals most essential for the manufacturing of clay brick products are kaolinite, illite, and quartz (Stein, 1982)."

Jan 1, 2017

By Ian Bell, Saman Nouranian, Shahram Tafazoli, Bahram Sameti, Mahdi Ramezani

"Image-based rock fragmentation sensing in mining and quarry applications includes an important rock boundary delineation step, which is commonly referred to as rock segmentation. This paper presents a novel approach to solve this problem, using artificial intelligence. In the proposed technique, priorknowledge of previously analyzed images is encoded into mathematical/statistical models. A set of human labeled images are used as training inputs. These images are used to train neural networksthrough an optimization process. The networks can then be used in real time for rock delineation. "

Jan 1, 2017

By A. Miura, G. Granata, C. Tokoro, A. Fuwa

"The high copper demand as well as the lack of new high-grade deposits, are pushing the copper industry to process low-grade and refractory ores containing chalcopyrite. However, for a quantitative dissolution of copper from the chalcopyrite, the leaching performances still need to be improved. In the present research, we studied and optimized the iodide-assisted leaching of chalcopyrite in H2SO4-Fe2(SO4)3 media. The evolution of surface species during leaching was determined by x-ray photoelectron spectroscopy (XPS) and mineral liberation analysis (MLA). Inductively-coupled plasma spectrometry (ICP-MS) was used to determine the dissolved copper. Significance of experimental results was assessed by statistical analysis while a kinetic analysis of the leaching process was performed by fitting the experimental data with the Shrinking-core model. Results showed the significant positive effect of iodide on copper extraction rate. In the presence of KI, the dissolution rate of copper was almost double than in the parallel experiments without KI. Whether using KI or not, elemental sulfur was generated on the surface of the leached chalcopyrite. Nevertheless, in the presence of KI, the passivation layer did not arrest the leaching. Analysis revealed that the leaching rate was limited by the chemical reaction control step.INTRODUCTION Due to the large demand of copper, processing low-grade ores containing copper sulfides such as chalcopyrite (CuFeS2) has become unavoidable (Watling, 2013). Since ores with CuFeS2 may also contain appreciable amounts of arsenic that cannot be smelted, and because low-grade ores are uneconomic to smelt, the hydrometallurgical technologies are crucial for recovering the copper (Dutrizac, 1978). Sulfate-based processes are attractive because of the lower operating costs and because the sulfate ion is more suitable in case copper would be recovered via electrowinning. In ferric sulfate solution, chalcopyrite undergoes oxidation due to the large amount of Fe(III) and dissolution due to the presence of the sulfate ion (Majima, et al., 1985). The leaching reaction in ferric sulfate medium can be represented as in (1):"

Jan 1, 2017

By A. Bozorgzadeh, B. M. Jensen, B. N. Koelling, B. R. Murtaugh

"The Service Base mooring system originally consisted of two general types of structures, 19 timber piles cabled together and steel three-legged pipe piles. The St. Louis District fleet moored to the fleet barges which were tied off to shore-side concrete deadman and supported on the landward side by the timber and steel piles. The purpose of this project was to replace the existing floating wharf mooring system at the St. Louis Service Base. The Marine Design Center of the U.S. Corps of Engineers developed a three pile cluster system concept. The clusters consisted of one vertical pile and two batter piles. Piles in rock sockets were selected to resist the uplift loads due to high wind loads on the tall, spare lock gates stored at the floating wharf. This paper focuses on the design of the rock sockets for steel pipe piles with large uplift loads and the lessons learned during the design and construction of this system.INTRODUCTIONBackgroundThe U.S. Army Corps of Engineers’ St. Louis District is located at the critical transition point on the Mississippi River where it is a “locking river” north of St. Louis and an “open river” to the south. The St. Louis District is responsible for maintaining navigation channels on the Mississippi River, the Illinois River and the Kaskaskia River. It is also responsible for the operation and maintenance of five locks and dams within its geographic boundaries.The St. Louis District utilizes a fleet of vessels (dredges, crane barges, motor vessels, and barges) to support the navigation mission identified above. The St. Louis District Service Base, located in St. Louis, Missouri, serves as the base of operations for the district fleet. This riverfront facility originally consisted of a floating wharf, a railroad trestle, and a walkway down the river bank to the floating wharf. Historically, there have been two fleeting areas at the Service Base. The main fleeting area was approximately 965 feet long and consisted of six fleet barges (Figure 1). This area supported the Dredge Potter and its attendant fleet. The upper fleeting area was approximately 1,050 feet long and consisted of various stop log, crane and work barges, dredge pipe pontoons and work flats."

Jan 1, 2017

By Kevin J. Ma, John Stankus, Dakota Faulkner

"Expandable rock bolts are widely used in hard rock mines as an efficient ground control product. However, capacity and service life can be significantly reduced if the metallic body is subjected to corrosion. In some hard rock mines in the U.S., highly corrosive ground conditions exist, and it has been reported that inflatable rock bolts have corroded within a few months after installation. To provide mining industry a cost-effective inflatable bolt and combat the corrosion issues, Jennmar Corporation, Inc., and its subsidiary Keystone Mining Services, LLC (KMS), analyzed corroded bolt samples, identified root causes, evaluated properties of various coating materials, and developed a new inflatable rock bolt, Python M3TM, that is protected with an innovative PyFlexU2TM coating. The new generation Python M3 features improved steel chemistry for reliable performance, modified profile for better inflation, and surface preparation and coating application. The PyFlexU2 is impervious to liquid and air, durable, and UV resistant. With a flexible adhesive, and highly corrosion-resistant undercoating, and a very hard sacrificial surface coating, the PyFlexU2 coating system provides the Python M3 superior protection against chemical corrosion and physical scratch damage. The under-coating has exceptional flexibility and adhesion to prevent coating micro-cracks or fractures after bolt inflation and possesses excellent corrosion resistance to acids (pH <3), alkalis (pH >11), fuels, and salt solvents. The corrosion and scratch resistant PyFlexU2 coating offers very effective bolt protection for extra longevity in highly corrosive environments. The Python M3 coated with PyFlexU2 has been tested in the most challenging conditions, including laboratory corrosion tests in extreme acidic and basic solvents, rock slurry, and borehole scratch insertion tests. With demonstrated corrosion and scratch resistance, the product has been greatly welcomed by hard rock mines in the West and is currently installed in large scale. This paper identifies the root causes of the bolt corrosion, discusses the analysis process, and details laboratory and underground tests carried out on the Python M3 coated with PyFlexU2. The Python M3TM and PyFlexU2TM are subjects covered by pending U.S. Patent Applications assigned to FCI Holdings Delaware, LLC."

Jan 1, 2017

By Steve Massman, Edward Wipf, Gary Beerkircher

"As mine size and tonnage continues to increase, material handling/processing equipment has also increased in size with 400 MT haul trucks, 2000 KW crushers, 12 M SAG/AG mills, 8.5 M ball mills, 3000 M3 flotation cells and 12.5 MW HPGR’s all with planned designs to increase in size further. Related equipment including vibrating screens have also increased in size with screens seeing feed rates of 3000 MTPH. Open circuit SAG Pre-Crush and closed circuit HPGR flowsheets are becoming more common with large screening requirements. Large multi-slope (banana) or horizontal screens are commonly used for these applications, however as the size of these screens has increased, the number and size of the brute force/overhead exciters has increased but with limitations. An example is a SAG discharge screen that will see surges of material from the SAG mill which overload the screen, reducing the screen stroke or throw causing a large reduction in screen efficiency with excessive fines & moisture in the screen oversize feed to the pebble crushing circuit. This paper will present some actual examples of the use of Two-Mass screens as a solution to these overloading problems and the advantages of Two-Mass screens in other high tonnage applications.Brute Force Drive Compared to Two Mass Drive Vibrating ScreensThe standard single mass screen as depicted by figure 1 is generally recognized in the mining industry. It is characterized by the screen body – labeled as the single mass (Mt) that is supported by isolation springs (Kiso). The stroke needed to process material is obtained by incorporating large eccentric wheels and/or drive boxes (Fb) directly mounted to the screen body via a drive tube."

Jan 1, 2017

By Italo Onederra, Miguel Araos

"Most of the current explosives for mining blasting activities are based on ammonium nitrate (ANFO, emulsions and watergels). AN-based explosives’ detonating properties were discovered in the 50’s and since then they have proven to be reliable, safe and cost effective. However, there is no current alternative raw material to replace AN. As part of a program of research initially funded by the Australian Coal Association Research Program (ACARP), Mining3 and the University of Queensland engaged in the search for potential oxidizing agent alternatives that could replace AN in the manufacture of mining explosives. Candidates included those that are produced in large quantities and that can be cost competitive with ammonium nitrate. The initial work identified hydrogen peroxide (HP), calcium ammonium nitrate (CAN) and sodium nitrate (SN). Explosives mixtures were prepared and sensitized using void sensitization techniques. The detonation properties results showed that explosives based onmixtures of HP/CN and HP/SN as the oxidizer were able to detonate in a range of 2000 – 5000 m/s, indiameters 50 and 102 mm, and densities in the range of 0.50 – 1.40 g/ml. Although more studies need to be conducted to fully understand these explosives, if successful, these explosives would be able to offer an alternative to the AN-based explosives in the mining industry."

Jan 1, 2017

By T. Rockley, J. Brune

"The mining of tabular deposits accounts for a significant portion of modern production in both underground hard rock and especially, soft rock mining. There is a large discrepancy between the availability of tabular reserves and the amount of development of these deposits, particularly when the deposit has a dip of around 25-50 degrees. This project studied the technical and practical barriers to the mining of these deposits through modern and historical case studies. The primary technical barriers to the development of these deposits are material movement and roof support. The study of historical attempts overcome these barriers and why they failed allowed us to research the possibility of implementing modern technology on previously unsuccessful methods. By modifying some common mining methods, some of these deposits can be mined at only a marginal increase in cost and using readily available equipment. These modified mining methods could make previously underdeveloped deposits to become viable. INTRODUCTION Tabular deposits are defined as orebodies that extend at least hundreds of meters along two dimensions, and a substantially smaller amount along another [1]. Moderately bedded tabular deposits are mined less often than their more horizontal counterparts due to the technical issues they present. These issues often cause lower productivity, higher cost, and more frequent accidents. Moderate dip is a less well defined term; but in this case, it will refer to any deposit which has a dip of at least 20°. This paper will focus on deposits that dip around 25°-50° and are deep enough to require underground excavation methods. These deposits are too steep for most conventional methods yet not steep enough for gravity fed methods to work efficiently. In some cases, this dip range is also referred to as intermediate or steeply dipping. The types of deposits most likely to fall into this category are sedimentary bedded deposits such as coal, trona, evaporates, placers, and other alluvial deposits. Some other types of deposits can fall into this category as well. These include some of the metal reefs such as the Bushveld Complex in South Africa, which was deposited by lava flows, but is tabular. Some areas have dips that fall into the moderately inclined category. There are also some metamorphic deposits such as slate or marble that can have dips of more than 20°. The dip angle of these deposits can cause several challenges. Ore movement becomes more difficult as the exceeds the limits of conventional conveyors, rubber-tired, or tracked vehicles. At the same time the dip is below the angle of repose of the material. This prevents gravity assisted haulage, as the ore and waste will not run downhill by itself. Another common problem in moderately inclined underground mines is roof support. The dip angle can increase the risk of pillar and support failure. This is due to slippage between rock layers, non-perpendicular support of the vertical stresses, and slippage of standing supports. The inclination leads to stresses that are not usually found in typical horizontally bedded deposits. These stresses may require larger pillars that may reduce ore recovery below profitable levels."

Jan 1, 2017

By D. C. R. Espinosa, P. Aliprandini, F. P. C. Silvas, J. A. S. Tenório, M. M. Jiménez Correa

"Nickel ores are divided into two types: sulfide deposits and lateritic deposits. About 60% of nickel resources are found in laterite ore, while the remaining 40% is contained in sulfide ore. Laterite ore is usually processed via pyrometallurgical means or through hydrometallurgical techniques that include acid leaching and metal value recovery from solution. In this study, copper and nickel adsorption by Dowex M4195 ion exchange resin from an acidic sulfate liquor was investigated. The acidic sulfate liquor was collected from an atmospheric leaching process (AL) of laterite ore. Ion exchange experiments were conducted in a batch system by varying parameters such as pH, time, metal concentration and temperature. Initially, mono-elemental synthetic solutions of nickel and copper were used in the experiments and then a synthetic solution simulating AL liquor was tested. Test results showed that the resin exhibited high selectivity towards copper and nickel, however, a high concentration of iron in the synthetic AL solution interfered with the recovery of nickel and cobalt by the resin.INTRODUCTION Nickel is one of the most important industrial metals in the world. It is widely used in industrial applications, such as the production of stainless steel, magnets, electroplating and special alloys (Dizge et al., 2009). The main sources of industrial nickel production are sulphide deposits; only 40% of industrial production uses lateritic ores. However, it is estimated that 60% of global nickel resources are found in nickel laterite deposits (Kuck, 2016). Since industrial nickel demand continues to grow, the development of new technologies for the extraction of nickel from laterite ores has become an interesting research topic (Agatzini-Leonardou, 2009)."

Jan 1, 2017

By Amr Al Degwe, Walid Jaber

"INTRODUCTIONNSCC International Ltd. carried out the enabling works and constructed the foundation system for the Emirates Pearl Tower and Bab El Qasr Hotel in Abu Dhabi. Emirates Pearl Tower is a joint venture project of TDIC- Tourism Development and Investment Company and ATLAS group, a leading telecommunication company in the UAE. Bab El Qasr Hotel is a project of EMROC Emirate-Moroccan General Trading & Investment Company. The combined enabling project is executed under the combined management of JACOBS International Holdings Inc. and NASSAR Engineering Services.The project is located to the south-east of Emirates Palace and west of Etihad towers, at about 20m away from the sea shore. Since the two projects are located next to each other a combined shoring system was constructed for the entire area. This decision was based on an agreement with clients and consultants of the two projects and resulted in significant savings for both parties. The shoring system consisted mainly of diaphragm wall with ground anchors and steel struts. Cantilever secant piles were used on the eastern side of the plot, adjacent to Etihad Towers` basement.PURPOSE AND SCOPE OF WORKNSCC International Ltd. was responsible for the design, procurement and construction of strutted and anchored diaphragm walls and cantilever secant piles. The shoring layout and a summary of shoring sections are shown below."

Jan 1, 2017

By Peter Middendorp, David J. Tara, Gerald E. Verbeek, Jan Fischer

"For pile driving simulation the model used must be accurate for the entire process, i.e. from the start of pile driving until the pile has reached its target depth. Of the various model components (hammer, pile and soil), the soil is the most difficult to characterize accurately. This is well known, but the aspect that is not as well understood (and therefore commonly misapplied) is the fact that the soil properties and thus the soil parameters do not remain constant during the pile driving process. Furthermore, this phenomenon of soil fatigue, mainly for skin friction, as a continual change of soil resistance during pile installation, is not implemented into all commonly applied pile driving simulation software and could therefore not be taken into consideration. In this paper the effect of soil fatigue will be described by numerous research results, showing that this effect will occur regardless. Different methods to consider the change of soil resistance during pile installation will be presented, some applying soil fatigue while others merely reduce soil resistances. Using currently available wave equation software that can take soil fatigue into consideration, the importance of doing so will be shown on the basis of the back calculation of a monopile installed offshore in Germany.THEORY BEHIND SOIL FATIGUESkin friction and toe resistanceTo simulate pile installation as accurately as possible, detailed geotechnical knowledge about the mechanical behavior of the soil surrounding the pile is necessary during each step of the installation process. Therefore, to ensure ""geo-mechanical correctness"" of a pile driving simulation, the shaft friction and the toe resistance have to be recalculated at each penetration level. For the skin friction parameters this is especially important since they change significantly during pile installation because of soil fatigue. Depending on the pile and soil type, the toe resistance can experience changes as well due to soil fatigue during to pile driving. However, in this paper the toe resistance values were kept constant over the entire penetration depth.In general, the unit skin friction can be derived from measured values (CPT, qs) or calculated as a function of the horizontal effective stresses dh acting perpendicular to the pile wall of a vertically driven pile. The horizontal stresses can then be converted into the unit skin friction qs using the Mohr-Coulomb failure criterion:"

Jan 1, 2017