Search Documents

By Fuqiang Zheng, Shuai Wang, Feng Chen, Yufeng Guo, Guanzhou Qiu, Tao Jiang

"The direct reduced iron powder and Ti-V-rich material was prepared from vanadium titanomagnetite concentrate by solid-state reduction-magnetic separation. The result indicated that under the studied conditions, adding KS can effectively improve the metallization rate of pellets. 2% KS was well mixed with vanadium titanomagnetite concentrate to make the pellets. The green pellet was preheated at 900 ? for 6 min. The preheated pellet was reduced at 1050 ? for 100 min, then crushed and ground to more than 80% was below 0.045 mm. The direct reduced iron powder and Ti-V-rich material were separated from the slurry by wet magnetic separation at 800Gs. The TFe content of magnetic material was 90.63%, and the Fe recovery rate reached 96.53%. The TiO2 and V2O5 contents of Ti-V-rich material were 28.40 % and 1.64 %, respectively. The TiO2 and V2O5 recovery rates were 69.05% and 96.82%, respectively. 1. Introduction The ilmenite and rutile are the main titanium resources which can be used in the present technical level and economic conditions[1,2]. However, with the rapid development of China’s economy, the market demand of titanium products is increasing sharply. The current supply of ilmenite and rutile cannot meet the needs of chemical industry[3]. China is rich in vanadium titanomagnetite concentrate which contains abundant titanium and vanadium resources. The TiO2 and V2O5 content of vanadium titanomagnetite concentrate are usually about 7% and 0.3%, respectively[4]. Because the TiO2 and V2O5 grades are low, it generally requires pre-concentrated to Ti-V-rich material before extracting the titanium and vanadium. Therefore, it is vital to find effective processes for pre-concentrating the titanium and vanadium in vanadium titanomagnetite concentrate. There are many methods[5-13] developed or under development to pre-concentrate Ti-V-rich material from vanadium titanomagnetite concentrate, including the blast furnace process, pre-reduction electric furnace process, to utilized vanadium titanomagnetite concentrate are direct reduction-electric furnace smelting, sodium salt roasting-direct reduction-electric furnace smelting and direct reduction-magnetic separation and so on. The blast furnace process and other methods cannot effectively utilize the titanium and vanadium resource due to the technical or environmental problems[9]. In this study, the vanadium titanomagnetite concentrate was obtained from Panxi region of China, the reserves of which account for 11.6% of vanadium and 35.17% of titanium all over the world[3]. The preparation of direct reduced iron powder and Ti-V-rich material based on reduction-magnetic separation is proposed. The process utilizes a new catalyst for titanium ore reduction in rotary kiln followed by magnetic separation. Using this novel technology, the titanium-vanadium and iron are successfully separated. Compared to the traditional reduction of Ti-bearing ore, the reduction temperature reduced to 1050 ?, leading to higher efficiency, lower energy consumption and investment, and broader applications."

Jan 1, 2018

By Yuki Koshino, Kenji Kaneko, Yasuhiro Aruga, Takuya Maeda

"In general, there is a strong correlation between dislocation characteristics and mechanical properties of aluminum alloys. In this study, dislocation characteristics of tensile deformed Al-Mg alloys were examined by transmission electron microscopy. An Increase in the solute concentration, ranging between 0.3 and 1.1%, Mg leads to increase in strength and decrease in uniform elongation. The accumulation of dislocations during the tensile deformation is observed in lower strain as the concentration of solute Mg in the alloy is higher. It is believed that the solute Mg in Al-Mg alloy promotes the accumulation of dislocation during the tensile deformation resulting in the decrease in elongation.INTRODUCTION The influences of the amount of Mg concentration on the tensile properties of Al-Mg alloys has been investigated by many researchers. It has been understood that the tensile ductility of Al-Mg alloy is higher for the Al-Mg alloys with higher Mg concentration beyond 2 mass% (Mukai, Higashi, Hirano & Tanimura, 1993). Uchida and Yoshida (1995) reported the formation of microbands during the tensile deformation due to the localization of dislocations, and the amount of microbands were reduced when the Mg concentration of the Al-Mg alloy was increased from 3 to 9 mass%. Their study suggested that the dynamic recovery of dislocation was retarded due to the increase of the Mg concentration during the tensile deformation, which resulted the increase in ductility. On the other hand, in the case of Al-Mg alloys with the Mg concentration less than 3 mass%, the reason why the ductility of Al-Mg alloys decreases with increasing Mg concentration has not been sufficiently investigated. In general, the Mg concentration used for automotive usage is less than 1 mass%, in the case of Al-Mg-Si alloys (Aoki, 2013). Therefore, to clarify the roles of Mg in the low concentration range on ductility of aluminum alloys and to elucidate its mechanism contribute to alloy design of Al-Mg-Si alloys having good formability."

Jan 1, 2018

By S. A. Lolon, J. F. Brune

"INTRODUCTION In underground longwall coal mining, the mined-out areas or gobs frequently contain methane which can form explosive methane-air mixtures. Historically, there have been many events of mine fires and explosions recorded in the United States and other countries that have demonstrated the existence of such explosive mixtures, herein referred to as Explosive Gas Zones (EGZs), inside and around the perimeter of bleeder-ventilated longwall gobs (Loane et al., 1975; Lynn et al., 1986; Elkins, et al., 2001; McKinney et al., 2001; Dziurzynski and Wasilewski, 2012; Brune, 2013). The risk of mine explosions can increase if the EGZs migrate out from the gob into the surrounding mine entries. Several factors can induce EGZs outflowing from the gob, but the most common cause is the fluctuating barometric pressure. Atmospheric pressures change regularly every day but can fluctuate abruptly and become increasingly hazardous in adverse weather conditions. Other sudden pressure changes can result from roof falls, failing ventilation controls and fan outages. Any such fluctuation of mine ventilation pressure will disturb the pressure differential between the gob and the surrounding mine workings and may cause EGZs to outgas from the gob. The correlation between major mine explosions and abrupt barometric pressure changes has been studied and confirmed for explosions in coal mining countries including the United States, South Africa, Australia, and Poland (Hosler, 1948; Boyer, 1964; Kissell et al., 1973; Fauconnier, 1992; Hemp, 1994; Wasilewski, 2014; Belle, 2014; and Lolon, 2017). Disastrous mine explosions appear to happen more frequently during stormy weather, which, in the United States, typically occurs during the late fall and winter seasons. ROOT CAUSE AND EFFECT OF GOB BREATHING Gob breathing is the result of the pressure differential between gob internal and external pressures caused by external atmospheric pressure fluctuations that occur naturally as a result of gravitational and thermal forces in the atmosphere (Lindzen and Chapman, 1969). Other major and sudden pressure changes may be caused by fan failures, failures of ventilation controls or roof falls can also cause an unexpected gob breathing. Normal barometric fluctuations occur every day but usually do not pose an explosion risk as they occur gradually so gob pressures have sufficient time to equilibrate. More extreme fluctuations associated with cyclonic weather systems and storms often result in more rapid and larger drops or rises in barometric pressure (Hosler, 1948; Fauconnier, 1992). A study by Lolon (2017) found that the timing of historical mine explosions showed consistency with the occurrence of abrupt and intense barometric variations."

Jan 1, 2018

By S. M. H. Haddad, M. Saghaeian, R. Hejazi

"Due to limited water resources in mineral processing plants, increasing the efficiency of iron tailing dewatering system in order to obtain more usable water is very important. In this research, flocculation process, as one of the best method for water recovery, was investigated by using one organic cationic and three anionic types of flocculants with different dosages (10, 20, 30 g/ton) and iron ore tailing slurry (8 % w/w solidity) in series of graduated cylinders and obtained results were compared. it is observed that for tailing sample, the anionic flocculants have a significant effect on the settling rate of solid particles compared to the cationic types. Furthermore, effects of temperature (10, 23 and 43 ºC) and pH (2, 7 and 12) on the rate of settlement and turbidity was studied by utilizing the best flocculant. Findings showed that by increasing the amount of flocculant dosage, sedimentation rate went up and turbidity decreased. Comparison the out-put data of tests indicated that at temperature 23 °C and pH=7, the best results for both of faster settling rate and producing more clear water were reached. It should be considered that lower temperature has a more negative effect on the sedimentation rate and overflow water quality. So it will be predicted that for cold seasons, the consumption of the flocculant powder would be higher than the moderate or warm seasons. Also, coagulation/flocculation was evaluated by applying organic cationic coagulant added to anionic flocculant in three different times. Different ratios of coagulant to flocculant was examined (70%:30%, 50%:50%, 30%:70%) as well. Overall, utilizing coagulant had desirable influence on sedimentation experiments and obtaining high quality water. 1- INTRODUCTION In mineral Factories, among the important processes, solid-liquid separation process due to limited resources of water is very important and operates on iron ore tailing in settling tank as thickener in order to gain clear water for preventing water loss and applying again in plant units (Ciftci and Serhat Isik, 2017). Iron ore tailing include inharmonious compounds of iron oxides, silicates and aluminum-silicates. The percentage of solid in the tailing usually changes between 5 and 10 percent (Dash et al., 2011). One of the major problem about dewatering of tailing in thickener is solid-liquid separation of slurries with high stability because of fine particles. It means that rate of sedimentation is very slow and recovered water quality is inappropriate. This issue can be solved to a large extent by factors such as pH control, ionic strength and flocculation/coagulation process which results in aggregation of particles so that settlement by gravity is happened (Dash et al., 2011)."

Jan 1, 2018

By J. B. Boisvert, D. S. Silva

"Drillhole placement involves benefits, costs, and constraints. Benefits are related to the drilling campaign value, which includes maximizing “indicated” and “measured” resources. Costs include drilling, rig movement, and access construction. Constraints include infeasible areas, maximum and minimum angles of drilling, maximum depth of drilling, and budget. Manually planning drillholes that meet these constraints is suboptimal. A framework for straight drillhole optimization that accounts for benefits, costs, and constraints is presented. The method aims to maximize the value of resources converted from “inferred” to indicated and measured. The framework is demonstrated for a Nevada gold deposit and outperforms manually selected drillholes.RÉSUMÉ Le choix de l’emplacement d’un trou de forage s’accompagne d’avantages, de coûts et de contraintes. Les avantages sont liés à la valeur d’une campagne de forage, qui comprend l’optimisation des ressources « indiquées » et « mesurées ». Les coûts englobent le forage, le déplacement de l’appareil de forage et la construction des routes d’accès. Quant aux contraintes, elles portent sur les zones impraticables, les angles maximums et minimums de forage, la profondeur maximale de forage ainsi que le budget. La planification manuelle des trous de forage répondant à ces contraintes est sous-optimale. Cet article présente un cadre relatif à l’optimisation des trous verticaux de forage tenant compte des avantages, des coûts et des contraintes. Cette méthode vise à optimiser la valeur des ressources converties de la phase « ressources présumées » à celle de « ressources indiquées et mesurées ». Ce cadre est appliqué à un gisement aurifère du Nevada et donne de meilleurs résultats que les trous de forage sélectionnés manuellement. INTRODUCTIONDetermining the optimum location of infill drilling has been studied because the high cost of drilling suggests that using fewer drillholes is preferred, and targeting locations of the deposit that are locally uncertain should result in better mine planning decisions and increased profit of the operation. Existing methods for optimizing drillhole locations consider minimizing the kriging variance (KV) as the objective and are mostly restricted to two dimensions (Soltani-Mohammadi & Hezarkhari, 2013a, b; Soltani- Mohammadi, Safa, & Mokhtari, 2016)."

Jan 1, 2018

By Sastry Putcha, Vamshi Vemula, Aneesh Goly, Kumar Allady

Current dynamic testing practice to obtain pile total capacity will not yield optimum capacity due to the strain incompatibility between the side and tip resistances during driving. Superposition of end of initial drive- static tip capacity and the peak static skin capacity during beginning of restrike and adding them is the preferred method. The FDOT method determines independent pile static tip and skin capacities in real time analyzing appropriate blows from the embedded tip and top data of the Embedded Data Collectors (EDC). This data is collected through a wireless radio transmitter, receiver, and laptop software. The approach utilizes EDC tip and top data and nonlinear single degree of freedom system to satisfy force and energy equilibrium with a global genetic inversion analysis. Top impacted energy equals at pile tip as sum of Static, Damping and Inertial energy providing independent tip resistance. With EDC sensors as boundary conditions, pile is divided into desired segments and using global inversion techniques one dimensional equation is solved for independent skin friction for every blow. EDC data compared close static load test results. The EDC - FDOT method has enabled cost effective 100% testing of driven piles cost effective. INTRODUCTION Historical documentation has shown that not only driven piles have a long history of usage but also continues to advance unceasingly till today. Historians placed the first pile driving using timber piles in the 4th century BC. While modern pile driving systematically started around nineteenth century, the credit for conceiving the idea of the applicability of wave equation to driven piles goes to David Victor Isaccs of Australia. His 1931publication “Concrete Pile Driving Formulae” provides the basis for modern pile driving using stress wave theory. He felt that the dynamic formulae then in use lacked the capability of detecting integrity and hence developed stress wave theory. This work was further developed starting in 1938 by W.H. Glanville and colleagues of British Building Research Board as they developed the first solution to the wave equation. But these early efforts have really taken off only with the advent of computers. E.A.L. Smith (1960) published ‘Pile Driving Analysis with the Wave Equation’ and provided first numerical solution to the wave equation. Within few years, the FHWA funded research and in due course this effort ushered the era of externally instrumented pile driving.

Jan 1, 2018

By O. A. Velasquez, A. R. Kumar

"Dust generated on underground mechanized coal mining faces is a health and safety hazard. Continuous miners deployed underground usually have an integrated flooded-bed dust scrubber mounted onto the machine that arrests the generated dust from close to the face and cleanses the air around it. However, the impingement screen might get clogged depending on the coal seam being worked. This necessitates the cleaning of the screen which in turn, reduces the overall availability of the scrubber and, hence the continuous miner. A novel non-clogging screen has been developed at the Department of Mining Engineering, University of Kentucky. The proposed impingement screen is built up of three individual aluminum screen units 1.5 mm thick and separated by 3 and 2 mm respectively. The screens have long vertical slits measuring 6 mm. A water spray continuously keeps the screen wet and provides for the filter element to arrest the dust particles. The slits force the dust-laden air to make sharp turns. The dust particles cannot change directions rapidly, impact one of the three screens and are separated out based on their momentum. Preliminary computational fluid dynamics (CFD) models have indicated significant cleaning efficiencies in the respirable range at the expense of much lower pressure drops. Results indicated by CFD models and supported by laboratory experiments have been discussed in this paper.ACKNOWLEDGEMENT The authors acknowledge the National Institute for Occupational Safety and Health (NIOSH) for funding this research. Dr. Thomas Novak, Professor of Mining Engineering, is also acknowledged for his continued support and encouragement. INTRODUCTION Continuous miners are ubiquitous in coal mining around the world. The miners are operated against bling headings, ensuring adequate flow of air at the face could be difficult. The minimum requirement of ventilation airflow quantities at those coal faces are legislated to dilute dust generated to harmless levels. New dust rules promulgated recently have further called for lower exposure levels of personnel working underground (Courtney) (MSHA, 2014) (NIOSH, 2010). Water sprays are also installed at strategic locations and serve as powerful air-movers. The sprays capture some amount of dust generated while cutting. In addition to this, usually, all continuous miners are equipped with a flooded-bed dust scrubber as shown in Figure 1 to capture the dust from close to the extraction drum (Chao & De-sheng, 2000) (Wala, Vytla, Huang, & Taylor, 2008) (Organiscak & Beck, 2010)."

Jan 1, 2018

By G. P. Karmakar, K. K. Chandan

"The drilling mud is an essential part of the drilling process, which plays a major role in keeping safe and efficient oil and gas well drilling. In the oil industry, bentonite clay dissolved in water produces the simplest type of drilling muds. Bentonite clay contains montmorillonite particles. These particles are dispersed uniformly in water and such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds. The bentonite clay easily dissolves in water and increases the viscosity of the water, which is one of the most important properties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for building up of the viscosity of the clay-water system. The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil and gas well drilling process. The behavior of drilling mud greatly depends upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations. In this work, a comprehensive study has been carried out to find out the effect of added polyacrylamide (PAM) polymer, surfactant, pH and salt concentrations on the dispersion/ flocculation characteristics of bentonite clay-water system. It has been observed that the increase in PAM dosage reduces the residual turbidity and improves the settling rate of the bentonite particles. The flocculation rate has also been found to be better under higher pH conditions. The combined effect of salt concentration and PAM dosage improved the overall flocculation efficiency of the system.INTRODUCTIONIn the oil industry, bentonite clay dissolved in water produces simplest type of drilling muds. Bentonite clay containes montmorillonite particles. These particles are dispersed uniformly in water. Such dispersions are used in various industrial products like paints, ceramics, pesticides and drilling muds (Akther et al., 2007). The bentonite clay easily hydrates in water and increases the viscosity of the mud system (Razi et al., 2013; Meng et al., 2012). Bentonite clay in the drilling mud increases the viscosity which is one of the most important prop erties of a drilling mud. Bentonite has the highest swelling capacity, which is responsible for the building up viscosity of the clay-water system (Sonmez et al., 2013). The drilling mud is an essential part of the drilling process, which plays a major role in keeping a safe and efficient oil or gas well drilling (ASME, S. S. C., 2005). The flocculation behavior of bentonite is one of the major concerns for the performance of the water-based drilling mud in the oil or gas well drilling process. This behavior of drilling muds greatly depend upon the quality and quantity of bentonite clay, as well as the additives that are used in their formulations (Yu and Amanullah, 2005; Akther et al., 2007). Bentonite particles form aggregate under certain conditions including high temperature, and high concentration (Luckham and Rossi, 1999). If the quality of bentonite is not sufficient to accomplish intended viscosity of the muds, it is essential to add certain additives to increase the viscosity and prevent aggregation of the system (Razi et al., 2013). The anionic polymer bearing sample can build up inter-particle bonds between the polymer and clay particles. The addition of various additives like, polymers control the dispersion and enhance the viscosity of the mud by controlling the flocculation of montmorillonite particles in bentonite dispersion (Heller and Keren, 2002; Mahto and Sharma, 2004)."

Jan 1, 2018

By Tong Gao, Jingyu Qin, Xiangfa Liu, Zengqiang Li, Yaoxian Zhang

"The recycling of aluminum materials is a green industry while Al–Si–Fe is a typical scrap aluminum alloy. The key point of recycling Al–Si–Fe alloys is to separate Al and Fe. A method by introducing Al–Si–Fe alloy into Mg melt has been investigated in this work. A separation layer with gathered Fe–rich and Al–poor Fe3Al0.7Si0.3particleswereobtained at the bottom of the cooled ingot, indicating that ß–Al5FeSi phase evolves to Fe3Al0.7Si0.3,and quantities of Al are released to the upper Mg matrix simultaneously. However, the evolution of Al3Fe by adding binary Al–Fe alloy into Mg melt is different. It is supposed that element Si plays an important role in the phase evolution procedure, thus affects the performance of this method.INTRODUCTIONThe rapid development of aeronautic, automotive and aerospace technologies strongly depends on the consumption of materials while sustainable development is the future direction. Aluminum is a recyclable material and Fe is one of the most common impurities. Fe can be introduced into Al alloys by adding low–purity alloying materials and by using unprotected ferrous crucible, tools, or equipment (Belov, Eskin, & Avxentieva, 2005; Lu& Dahle, 2005).For instance, wear–resistant rings are usually inserted into piston head when producing Al–Si pistons and an infiltration procedure by putting the cast iron rings into Al melt before casting is always essential. As a result, both the re–melting of pistons and the reuse of Al melt for infiltrating rings lead to the enrichment of Fe element, which can be even high to5 wt.%(Viala, Peronnet, Barbeau, Bosselet, & Bouix, 2002).It is widely known that coarse ß–Al5FeSi particles will form in high Fe–contained Al–Si–Fe alloys which is harmful for the mechanical properties. In the past decades, several methods to eliminate the harmful effect of ß–Al5FeSi have been investigated which can be widely referred (Munson, 1967; Lee, Kawamura, Inoue, Cho, & Masumoto, 1997; Suárez–Peña& Asensio–Lozano, 2006; Eidhed, 2008).These methods can be divided into two kinds. One is to aggregate and remove the Fe–rich phase through the methods of centrifugation, gravity filtration or magnetic separation. The other way is modifing the morphology of flake–like ß–Al5FeSi by overheating the melt or adding neutralized elements. However, these traditional methods are rarely used due to respective disadvantages, while the commonly used method in industries is using primary aluminum for dilution. However, only less than 30wt.% of scrap Al can be added into primary Al melt for each melting work while it also results in the decrease of product quality simultaneously(Zhang, Liu, & Liu, 2016)."

Jan 1, 2018

By M. Somppi, Z. Yamak

"Gold producers invest significant effort in mining, processing, and creating an intermediate gold doré product. Nonetheless, equal effort should be extended to the final handling and processing of the doré bar, and managing the high-purity gold produced at the fine-gold toll refiner. This detailed attention to bullion handling and refining provides rigor and confidence that the mine site is achieving, through fair and controlled methodology, the most appropriate value for the final product. With the above in mind, the following study explores the importance of preparing a set of site best-practices for bullion handling and specifically, detailing the peculiarities of sampling methodologies and the impact on assays.INTRODUCTION Gold and silver handling practices are common place at mine sites and refineries. The practices include but are not limited to smelting, ingot casting, weighing practices, and secure transportation. Proper handling and processing of the bullion material ensures that the mine site is achieving the true value of the final product. Various handling aspects can critically impact the perceived value of the bullion. A few of these particulars include weight tracking, scale recertification and calibration, refining and melting practices, melt temperature measurement, sampling, pouring, bar cleaning, furnace technology and crucible selection, and assaying. Nevertheless, this report discusses and focuses on the importance of proper sampling and molten-metal temperature measurement and their potential impact on the final doré bar value. Refining or re-melting operations achieve a proper measure of the precious metal content of its bullion when the sample accurately represents the whole bar. At first this task appears seemly straightforward, however, taking a representative sample can be challenging and is also one of the most important tasks for valuing gold during the settlement stage at the precious metal refinery. Various bullion sampling methodologies exist; including: dip sampling, granulation, drilling, cutting, and vacuum pin sampling. The Royal Canadian Mint (2009) indicated in their technical review of refinery operations that pin sampling is one of the best methods for cases where representative sampling and accuracy are required, e.g. to determine the payable metal content. Pin sampling consists of inserting a sealed glass vacuum tube (Figure 1) into the molten metal; when the molten metal contacts a purposely-designed weak portion of the glass, the seal breaks and the metal is suctioned into the hollow centre (Figure 2)."

Jan 1, 2018

By David F. Gearhart, Mark Van Dyke, Heather Dougherty, Ted Klemetti, Gabriel S. Esterhuizen

"Coal mine longwall gateroads are subject to changing loading conditions induced by the advancing longwall face. The ground response and support requirements are closely related to the magnitude and orientation of the stress changes, as well as the local geology. This paper presents the monitoring results of gateroad response and support performance at two longwall mines at a 600-ft and 2,000-ft depth of cover. At the first mine, a three-entry gateroad layout was used. The second mine used a four-entry, yield-abutment-yield gateroad pillar system. Local ground deformation and support response were monitored at both sites. The monitoring period started during the development stage and continued during first panel retreat and up to second panel retreat. The two data sets were used to compare the response of the entries in two very different geotechnical settings and different gateroad layouts. The monitoring results were used to validate numerical models that simulate the loading conditions and entry response for these widely differing conditions. The validated models were used to compare the load path and ground response at the two mines. This paper demonstrates the potential for numerical models to assist mine engineers in optimizing longwall layouts and gateroad support systems.INTRODUCTIONThe need for roof stability in coal mine longwall gateroads places significant demands on the gateroad ground support system. The variable loading conditions associated with the approaching longwall face can cause excessive ground deformations that need to be accommodated by the support system. In coal mines in the United States several different types of supports are used to maintain the stability of gateroads. The supports may include grouted roof bolts, cable bolts, and roof trusses as intrinsic support. Standing supports include timber cribs, engineered timber props, and various types of cement-based cribs. The intensity of support is governed by the expected geologic conditions and the expected stress changes that will occur during longwall mining. At present, the design of ground support for gateroads is largely based on local experience. In-mine trials are usually conducted when new support technologies become available or ground conditions dictate a change in the support system. The research reported in this paper has the objective to assist mining engineers in evaluating alternative gateroad supports and to design suitable support systems for the local ground conditions."

Jan 1, 2018

By Andrew Port, Ali Ghandeharioon

Nonlinear seismic deformation analyses using the finite difference program FLAC were performed for a wastewater treatment plant to estimate foundation displacement and performance of two proposed trickling filters during the 2475-year event design earthquake. The effective stress based constitutive model UBCSAND, which captures the cyclic behavior of both the “sand-like” and “clay-like” materials, was used to model the dynamic response of the soil strata. Dynamic analyses of the site indicated that in absence of ground improvement or deep foundations beneath the proposed trickling filters, those structures would undergo horizontal displacements in excess of 1 m and short-term differential settlement gradient of about 400 mm over 50 m as a result of seismic and post-seismic settlements. Three mitigation options were considered for limiting the seismic displacements and differential settlement gradients of the proposed trickling filters. These alternatives include vibro-replacement stone columns, vibro-replacement stone columns plus supplementary cutter soil mixing (CSM) configurations, and pile foundations. Various layouts for each mitigation option were considered including the lateral extent of the ground improvement, CSM walls and pile spacing. Seismic horizontal and vertical displacements of the proposed structures as well as post-earthquake consolidation settlements due to dissipation of excess pore water pressures in soil layers were assessed in all the analysis alternatives. The analyses indicate that all the alternatives considered have the potential to provide a comparable level of seismic and post-seismic performance. However, for similar performance levels, the ground improvement options need to extend well beyond the edges of the proposed structures, while the piles can be limited to just beneath the footprint of the structures. INTRODUCTION Annacis Island Wastewater Treatment Plant (AIWWTP) is owned and operated by Greater Vancouver Sewerage and Drainage District and services a population of approximately 1 million people in Vancouver, British Columbia. Wastewater is generated by residential, commercial, and industrial sectors and the treated effluent is discharged to Annieville Channel of Fraser River on the south side of Annacis Island. AIWWTP is located on a 51-hectare site and was commissioned in 1975 as a primary treatment plant, but has had two major expansions to meet the population growth needs, and to improve the treatment process efficiency through the provision of secondary treatment of the liquid stream. The current expansion includes construction of additional solids contact tanks and secondary clarifiers. Future expansions include the construction of proposed additional trickling filters. New expansion structures are required to be designed for post-seismic operation after the 2475-year event design earthquake.

Jan 1, 2018

By I. Nishkov, I. Grigorova, N. Valkanov, M. Ranchev

The processing of sulphide ores with variable and complex mineral composition and physical properties, such as those processed by two-stage selective flotation scheme in “Erma reka” concentrator, Minstroy Holding JSC, requires excellent selectivity in order to achieve acceptable concentrate grades. The lead-zinc ores from the hydrothermal lead-zinc deposits mainly contain galena (PbS), sphalerite (ZnS), pyrite (FeS) and chalcopyrite (CuFeS2), as well as non-metal minerals such as quartz, carbonates and clinopyroxenes skarns. One of the main impurities present in sphalerite is iron, which is known to be detrimental to the rate of sphalerite flotation and its recovery. The results from the conducted laboratory and industrial tests, presented in the previous study, showed that it is possible to depress the iron rich sphalerite by adding MINFIT® (modified sulfur-oxy depressant) at the pH of approximately 9.5 in rougher lead flotation circuit, leading to reduction of zinc sulphate consumption and complete elimination of cyanides from the flotation process. Furthermore, the consumption of copper sulphate, which reactivates the surface of the zinc minerals, was significantly reduced. Consequently, the optimisation of the reagent regime in the Erma reka concentrator, led to notably improved qualitative (grade, recovery) properties of the final lead and zinc concentrates. Moreover, when comparing the reagents consumption for 2014 and 2016 – when the processing plant have been applying the new optimized reagents regime, comprises the use of MINFIT as the primary depressant, the following results have been achieved: ZnSO4 decreased by 30%; CuSO4 consumption decreased four times and full rejection of cyanides from the process. Finally, this paper provides a state-of-the-art review of the obtained results during the period of application of the new flotation reagents regime in the Erma reka concentrator, Minstroy Holding JSC.

Jan 1, 2018

By T. Wajima

"A novel carbonaceous immobilizing agent for heavy metal contaminated soil was prepared from rice straw using sulfur immersion and pyrolysis, and the lead immobilization in artificial contaminated soils using sulfur-impregnated carbonaceous material was estimated. The rice straws were cut to 1 cm pieces, and then immersed in 0.1 - 1 M K2S solution for 0 - 24 h to prepare sulfur-immersed materials. The immersed-materials were heated at 400 oC for 1 h in nitrogen gas to produce the sulfur-impregnated carbonaceous material by pyrolysis. The abilities of the product to immobilize lead from aqueous solution were examined to obtain the product with high lead immobilization ability. With increasing K2S concentration, the immobilization ability of the product for lead gradually increases and then above 0.5 M K2S those are almost constant, while 15 min is sufficient for the immersed time to obtain the product with high lead immobilization ability. The product prepared from material immersed in more than 0.5 M K2S solution for less than 15 min has a maximum immobilization ability for lead ion. The lead immobilization using the sulfur-impregnated product is sustainable due to the formation of leadhillite [Pb4SO4(CO3)2(OH)2] and anglesite [PbSO4]. The product can immobilize lead ion in various artificial lead contaminated soils. By mixing artificial lead contaminated soil with the sulfur-impregnated product, the eluted solution became neutral, and the eluted concentrations of lead ion dropped below the Japanese elution standard for soil.INTRODUCTION Soil contamination with heavy metals is a worldwide problem. Accumulation of heavy metals in soils affect soil ecology, agricultural productivity, quality of agricultural products, water resources, and serious health problems for human and animal (Raicevic, et al., 2005). In the United States, for example, approximately 63 % of the sites on the National Priority List (NPL) for the treatment of contaminated soils are contaminated by metals, and lead is the most common metal, found at 15 % of the sites. In Japan, according to a report by the Ministry of Environment, 43 % of the contaminated sites that exceed the environmental quality standards are contaminated by lead compounds. Soil contamination by lead compounds is also prevalent in other developed and developing countries where lead compounds are used extensively in industrial activities without careful contamination management. Lead is a ubiquitous heavy metal pollutant in soils due to their use widely. The primary sources of Pb contamination include industrial activities such as mining, smelting of metals, and the use of Pb-containing products such as paints, lead-acid batteries, bullets, gasoline and pesticides (Cao, et al., 2009). It can damage human nervous (especially children) and reproductive systems (ATSDR, 2007). The high concentration of Pb in the soil poses risks to human and animal health by the leaching of metals from the soil into water and the consumption of edible plants growth in the contaminated soil. Therefore, proper remediation is necessary to reduce metal availability in soil for protecting human health."

Jan 1, 2018

By S. Espley, T. Nyabeze, D. Beneteau

"Many mentorship programs are available to Canadian mining industry employees. Some are company-led initiatives, whereas others are provided through educational institutions or nonprofit organizations. In 2016, a national survey was launched to gain insight into perceptions of what mentorship is, learn about available programs, and collate experiences with formal and informal mentorship opportunities. This paper outlines survey findings and delivers recommendations to industry for consideration in employee mentorship programs. In addition, mining industry leaders share their mentor/mentee perspectives. The intent of this paper is to bring awareness of best practices that can help employees grow and develop in their profession.RÉSUMÉ Les employés de l’industrie minière canadienne ont accès à de nombreux programmes d’encadrement. Certains sont des initiatives menées par les sociétés, d’autres sont proposées par le biais d’établissements d’enseignement ou d’organismes à but non lucratif. En 2016, une enquête à l’échelle nationale a été lancée en vue d’obtenir des informations quant à la perception de ce qu’est réellement l’encadrement, de découvrir les programmes proposés et de comparer les expériences aux possibilités d’encadrement, officielles ou non. Cet article présente les résultats de cette enquête et fournit des recommandations à l’intention de l’industrie afin qu’elle les prenne en compte dans ses programmes d’encadrement des employés. En outre, des chefs de file de l’industrie minière partagent leurs points de vue conseillers/protégés. L’intention de cet article est de sensibiliser les employés aux meilleures pratiques, ce qui les aidera à évoluer et à se développer dans leur profession. INTRODUCTIONThis paper about mentorship in the mining industry is based on voluntary responses to a cold survey, written and circulated by the authors. In 2016, a link to an online mentorship survey was circulated to males and females in the mining industry with the belief that mentorship programs should be available to everyone. The link was delivered via the authors’ personal networks in mining, the CIM Reporter, Women in Mining (WIM) email blasts, LinkedIn, and Facebook. This paper summarizes the answers to the survey questions. The paper is a follow up to one by the same authors (Nyabeze, Espley, & Beneteau, 2010), which was written to gain insight into why women join and stay in the mining industry, and to learn why the overall representation of women is low."

Jan 1, 2018

By R. Holmestad, M. Gazizov, S. Wenner, R. Kaibyshev, J. K. Sunde

"Mechanical properties and microstructure of an Al-4.7Cu-0.74Mg-0.51Si-0.48Mn-0.10Cr-0.09Ti-0.02Fe (wt. %) alloy subjected to various thermomechanical processing (TMP) have been investigated and compared to conventional ageing at 170°C (designated T6). Three TMP routes involving cold deformation of solution treated samples were tested. These were (i) 3%-stretching (T8-3%), (ii) equal-channel angular pressing (ECAP) to true strain (e) of ~1 (T8-1) and (iii) ECAP to e~2 (T8-2), all with subsequent ageing at 170°C for 0-96 h. At peak age conditions, both yield stress, ultimate tensile strength and elongation-to-fracture decreased for the T8-3% state as compared to the T6 condition. Intermediate ECAP (T8-1 and T8-2) lead to significant increase in maximum yield stress, ultimate tensile strength and elongation-to-fracture. The changes in mechanical properties were related to microstructure evolution, encompassing changes in grain sizes, dislocation densities, precipitate morphology and phase fractions, which were characterised using transmission electron microscopy. Relations between TMP, precipitation behavior and contributions to different strengthening mechanisms are evaluated.INTRODUCTION Al-Cu-Mg-Si alloys are widely used as structural materials in aerospace industry due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance. These properties are largely due to the formation of a large number of nano-sized metastable precipitates during artificial ageing (Polmear, 2006; Eskin, 2003; Gazizov, Dubina, Zhemchuzhnikova, & Kaibyshev, 2015). The precipitation behaviour in these alloys is complicated and depends among other things on Cu concentration and the Mg:Si ratio (Wolverton, 2001; Chakrabarti, & Laughlin, 2004). In general, the precipitation sequence has been presented in a prior study (Eskin, 2003) as follows:"

Jan 1, 2018

By E. Barnard, J. Tero, J. Rajala, N. Avenido, M. Fullam, A. Nashitati, S. Mbalamba

"The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum, with an average reserve gold grade of 1.28 g/t. The ore is high in Gravity Recoverable Gold (GRG), which varies between 73-91%, depending on ore type. Overall gold recovery since start-up is 98.2%, with about 63.5 % coming from the gravity circuit as doré. 2016 cash operating costs, and all in sustaining cost (“AISC”) were $361 and $604 per ounce, respectively.During design, three ore types were tested for GRG content, and based on the high GRG value of all three ore types, the decision was made to treat the full ball mill circulating load by gravity. Once operating, the gravity circuit performance was characterized by performing a detailed gravity audit, which included the ore, cyclone classification, Knelson concentrators, and the Consep Acacia intensive leach system. The deeper ores contain significant pyrrhotite, and this created some unusual challenges that had to be overcome. This paper presents the gravity circuit design process, the circuit commissioning, and the audit results and ongoing improvements.IntroductionHeadquartered in Vancouver, Canada, B2Gold Corp. was founded in 2007. Currently, B2Gold has five operating mines, and numerous exploration projects in various countries, including Nicaragua, the Philippines, Namibia, Mali and Burkina Faso. The Otjikoto Mine is located in the north-central part of the Republic of Namibia. It is situated approximately 300 kilometers north of Windhoek, the country’s capital, within the Province of Otjozondjupa. The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum. During design, a large emphasis was placed on gravity recovery, as the Otjikoto ores are unusually high in Gravity Recoverable Gold (GRG)."

Jan 1, 2018

By A. A. Rogozhin, E. G. Likhnikevich, S. I. Anufrieva, A. V. Kurkov

"Russia is among the nations holding the world's largest lithium ore reserves. Lithium is of key importance for the global economy. Therefore, it is important to review the current state of technology research aimed at finding the most effective solutions for the recovery of lithium from promising reserves in Russia. In Russia, a number of process solutions for the flotation of spodumene into salable concentrate (5% Li2O) have been implemented at the earlier existing complex low-grade ore concentration project. By applying these solutions, a sample of high-grade spodumene ore (4.7% Li2O) of the Greenbushes deposit was processed into a spodumene concentrate (7.5% Li2O) at a high recovery (~93%) of lithium. In Australia and Canada, new processes have been developed for the recovery of high-grade spodumene concentrates from high-grade ores using dense medium separation and flotation. For the recovery of mica lithium concentrates from low-grade ore, a flotation process was developed in Russia using the cationic collector ANP-2 and Oxifos-B as an additional collector. Low-grade ore containing 0.14% of lithium oxide was processed into a 2.7% Li2O concentrate. New hydrometallurgical lithium concentrate and ore processes are developed to avoid high-temperature (>1000 °C) roasting. The Sileach process (Australia) includes leaching of lithium ore with sulfuric acid in the presence of a halogen-containing component at a temperature of 95-115 °C. In the Russian process, lithium is recovered into an alkaline solution from low-grade spodumene ore in a pressure alkaline leaching environment (250 °C, NaOH concentration > 300 g/l). The developed concentration and hydrometallurgical methods will allow to design on their basis efficient processes for recovering salable products for hi-tech industries from lithium ores.INTRODUCTION Lithium has many unique and important properties. It is the least dense hard metal. Its alloys have some of the highest strength-to-weight ratios. Lithium has the lowest melting point of all known solid elements and is used as a highly-effective heat transfer medium. The high demand for lithium is due primarily to its unique electrochemical potential and low thermal expansion coefficient. It is used in the production of glass and ceramics, in petrochemicals, metals, medical and other industries. Since the late 20th century, the electronics industry has been the largest consumer of lithium. In recent years, lithium has attracted much attention also as an important component of ultra-lightweight electronic devices. It is also the preferred metal for electric batteries used in mobile electronic devices, vehicles, household power generators, making it an important resource for the development of environmentally friendly technology. Leading automotive brands have ambitious plans for the production of electric cars — Tesla Motors, VW, Toyota, GM, BYD Auto. It is expected that the production of electric vehicles alone will triple the demand for lithium by 2025. A sharp increase in the production of lithium is expected. Lithium has all the prerequisites to become a strategic resource of the 21st century. (Deutsche Bank, 2016; Bradley et al, 2017)"

Jan 1, 2018

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

By M. B. Daza, B. Lattimer

"Even with modern detection and firefighting techniques, mine fires continue to be a safety concern. However, some underground mine fires can be addressed with the remote application of high expansion foam, reducing firefighter exposure to hazards. The flow of this foam can be numerically or computationally simulated in order to gain a better understanding of its behavior, but rheology parameters are needed as inputs to produce accurate simulations. For this reason, this work studies the rheology of firefighting high expansion foam using a foam generator and Poiseuille –Flow Rheometer. Rheological parameters for foams with expansion ratios between 250-1280 are represented by the consistency index (k) and the power law index (n) due to the results show a strong agreement with the Power Law model for non-Newtonian fluid viscosity. Furthermore, experimental results show that high expansion foam behaves as a shear thinning fluid with a power law index around 0.4 and viscosities in the range of s 0.1 Pa-s and 0.042 Pa-s under shear rates between 44 ??-1 and 187.3 ??-1. INTRODUCTION High expansion foams are called to foams with expansion ratio greater than 200. Expansion ratio (??) is defined as the ratio between the volume of foam produced (i.e. volume of foam solution and volume of gas) and the volume of foam solution used (NFPA 2014). Because of its high expansion ratio, one of the most important application of high expansion foams is to fill or flood large spaces such as hangars, storage facilities and underground mines for fire suppression. The foam can fill large structures using small quantities of foam solution within a short time (Sthamer 2012) (Martin 2012). Although the specific high expansion fire suppression mechanism has not been understood on a quantitative basis, a possible mechanism is fuel isolation when the foam act as a physical barrier between oxygen and the flame. Furthermore, as a consequence of this contact water is evaporated, causing cooling of fuel and surrounding air. Besides, water vapor as product of water evaporation causes a dilution of oxygen concentration available to the fire (Fleming and Sheinson 2012). High expansion foam can be applied remotely by means of conduit pipes or in situ close to the fire. In most of the underground mines scenarios, fires have to be addressed remotely to reduce miner and firefighter exposure to the hazards (Smith et al. 2005). Although high expansion foams should not be blasted and must be deposited directly on the area of application because of their low density (Harding et al. 2016) sometimes it is complicated to apply it directly to the fire due to complex access areas at underground mines. In these cases, foam has to be applied far away from the fire. Despite of this fact there is a lack of knowledge in terms of rheological behavior of high expansion foam under high shear rates (Gardiner, Dlugogorski, and Jameson 1998). Furthermore, there are a few attempts to simulate numerically the high expansion foam flow due to the ignorance of its rheological parameters and its complex behavior. (Weaire 2008)."

Jan 1, 2018