Search Documents

By Peter Zhang, Daniel Su, Essie Esterhuizen, Mark Van Dyke, Berk Tulu, Dave Gearhart

"Roof falls in longwall headgate can occur when weak roof and high horizontal stress are present. To prevent roof falls in the headgate under high horizontal stress, it is important to understand the ground response to high horizontal stress in the longwall headgate and the requirements for supplemental roof support. In this study, a longwall headgate under high horizontal stress was instrumented to monitor stress change in the pillars, deformations in the roof, and load in the cable bolts. The conditions in the headgate were monitored for about six months as the longwall face passed by the instrumented site. The roof behavior in the headgate near the face was carefully observed during longwall retreat. Numerical modeling was performed to correlate the modeling results with underground observation and instrumentation data and to quantify the effect of high horizontal stress on roof stability in the longwall headgate. This paper discusses roof support requirements in the longwall headgate under high horizontal stress in regard to the pattern of supplemental cable bolts and the critical locations where additional supplemental support is necessary.INTRODUCTIONLongwall mining is the primary underground coal mining method in the United States and currently accounts for more than 60% of the underground coal production. The longwall headgate, as a passageway for the longwall crew, intake air, material supplies, and coal belt transportation, is critical for both safety and continuous production of the longwall panel. A roof fall in the longwall headgate would not only result in substantial interruption of production but could potentially cause injuries or fatalities. Rehabilitation of failed roof in the headgate would also expose miners to the risk of injuries. Roof falls in the headgate, though infrequent, mostly occur in the belt entry near the face. Considerable research has been conducted to determine the effects of various factors on headgate roof stability, as well as effective measures to support the roof in longwall mines in the Pittsburgh seam (Mark, Mucho, and Dolinar, 1998; Chen et al., 1998; Su and Hasenfus, 1995; Su, Thomas, and Hasenfus, 1999; Su, Morris, and McCaffrey, 2002; Su, Draskovich, and Thomas, 2003; Hasenfus and Su, 2006; Van Dyke et al., 2015). Previous studies have demonstrated that high horizontal stress and transitional roof geology are primary factors that cause headgate roof failure. These studies also showed that panel orientation, retreat direction, pillar sizes, and roof support played an important role in the stability of a headgate.In underground coal mines located in the eastern United States, the magnitude of the maximum horizontal stress is typically three times greater than the vertical stress, and about 40% greater than the minimum horizontal stress. Mark, Mucho, and Dolinar (1998) studied seven cases of headgate failures caused by high horizontal stress in different coal seams in the United States and stated that roof stability is affected, to a large extent, by rock type, entry orientation, and longwall orientation. The effects of horizontal stress can be summarized in these statements: (1) A laminated roof is very vulnerable to high horizontal stress. (2) Entries that are aligned with the maximum horizontal stress will suffer less damage on development than those perpendicular to it. (3) Horizontal stress concentration and relief depends on panel orientation, the direction of retreat, and the sequence of longwall panel extraction."

Jan 1, 2018

By Bret N. Lingwall, Byron Foster

The problem of reliable extreme event modeling of large diameter piles under enormous structural or kinematic loads has gained more attention in recent years. In particular, the soil response around the foundation and impacts to buried adjacent infrastructure has gained interest. One of the principal shortcomings with analysis of large diameter pile foundations under extreme event lateral loading is the reliance on conventional beam on elastic foundation methods, which do not model the soil field response around the pile. These methods are limited for large displacement problems, and for large diameter piles. However, the fundamental interactions between steel and concrete, and structure to soil are difficult to constrain, especially in large strain problems where the structural elements become inelastic. The non-linear interaction of the structural materials and soil is desirable so that assessment of stress changes in the field and effects on adjacent facilities can be modeled. A numerical modeling methodology that addresses these shortcomings has been developed. This method utilizes the interaction of brittle concrete with discrete steel reinforcing and casing in a robust manner capturing inelastic non-linearity in both soil and structure. This paper presents a comparison study of the method, wherein three different validation studies were made to data from full scale laterally loaded pile testing. INTRODUCTION Extreme event lateral loading of deep foundations comes in many forms including earthquakes, landsliding, tsunamis, hurricanes, surface fault rupture, liquefaction induced lateral spreads and many more. These extreme events induce loads on foundations far greater than service or strength loads. Perhaps the most dangerous extreme event loads are those of large soil displacements such as landslides, lateral spreads, and surface fault rupture, wherein the soil surrounding the foundations can move laterally 100 mm to 3 m! In these extreme event loading scenarios, small diameter foundations are pushed past their limits and many engineers prefer large diameter deep foundations for these situations. These deep foundations of diameter 900 mm or greater may be auger cast in place piles, cast in drilled hole piles, cast in steel shell piles, cased or uncased drilled shafts, bored precast piles, etc. For convenience in this paper, large diameter deep foundations will be referred to as Large Diameter Shafts (LDS). In LDS, steel may or may not used as a shell around the perimeter of the concrete and/or as internal tensile reinforcement. The interaction between brittle concrete and ductile steel within and/or along the perimeter of the LDS is critical to understanding the non-linear inelastic behavior of LDS for problems of large lateral displacements from extreme events.

Jan 1, 2018

By S. Corrent, F. A. V. Guimarães, M. G. Barbosa

"INTRODUCTION Moisture can be a villain, so new technologies have been explored to make more viable the production of high moisture iron ores. The current work presents the attempt of the utilization of a superabsorbent polymer (SAP) to aid in the screening process and in the ore handling process, such as stockpiles reclaiming and vessels/trains discharge in sub-zero temperature conditions. The results have shown that the polymer can be used in certain cases to improve productivity and increase safety in the process of handling the material (by increasing the TML). However, for size separation no advantages were found upon the use of the polymers. WATER ADSORPTION MECHANISMS The use of water in mineral processing is constant as its utilization brings an increase in the efficiency of separation. Although we have better results in the processing with water, materials with a high content of “natural” moisture can be very difficult to be treated by the conventional methods of separation. Nowadays many studies have been conducted in order to understand the effect of adsorption of water in the particles of complex minerals. Those studies have being divided in many different lines of research such as contact angle of a drop of water and the surface of the mineral to determine hydrophobicity, the particle size distribution and the porosity of particles. Mainly two forms of adsorption of water by the particles are possible: one the water is retained inside porosity of the particles. Laboratory tests developed in China have showed that capillary adsorption is faster in coarser particles that achieve the saturation degree earlier than finer particles (Xuewei Lv et al., 2011). The so called non-porous model considers the effect of water in the bulk sample of iron ores, in a physical connection when all the water works as a binder between particles as shown in the figure 1.If we take into account the compressibility of the system and compaction due to the weight of the bed over the particles, the thickness of the water film between particles is the same but the volume inside different particle size systems is much higher than in a system with particles of same size."

Jan 1, 2018

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By D. G. Lynch, M. R. Martin, R. J. Coutts

"Broadmeadow Mine is an underground longwall mine located in Central Queensland, Australia. The mine introduced a top coal caving (TCC) longwall face in 2013 but since then has experienced severe convergence events at the start of each panel after 60–70m of retreat, resulting in equipment damage and the longwall almost becoming iron bound. A significant geotechnical monitoring effort during LW10 and LW11 to characterise the caving mechanics and operational changes during LW11 were successful in mitigating the risk posed by these initial convergence events. This paper describes the geotechnical monitoring programme undertaken during LW11, the operational methods used to mitigate these initial convergence events, and the contribution to these events of the TCC technique.A thick sandstone unit close to the extraction roof was likely the cause of the convergence events at the start of each longwall panel. However, stress change monitoring cells, surface extensometers, an inclinometer, and the blockage of holes designed for pre-conditioning using hydraulic fracturing indicated that the convergence events were not caused by the sudden collapse of sandstone bridging across the goaf. Rather, they were caused by the propping action of strong units within the overburden strata. Equipment design modifications were made to allow the longwall to remain operational during the convergence events and an operational strategy was implemented to mitigate convergence in LW11. The initial convergence event was successfully negotiated, and Broadmeadow went on to be the highest producing longwall for CY16 in Australia.INTRODUCTIONBroadmeadow Mine is an underground longwall mine located in Central Queensland, Australia, owned and operated by BHP Mitsubishi Alliance (BMA). The mine is a punch longwall mine using open cut pit access provided by Goonyella/Riverside Mine. Broadmeadow commenced longwall operations in 2005 using a conventional high reach longwall, but later changed to the top coal caving (TCC) method of extraction. Broadmeadow extracts the easterly dipping 5.5–7.5m-thick Goonyella Middle Seam in ranging in depth from 90m to 330m. The coal is washed and blended at the adjacent Goonyella/Riverside open cut mine to produce a premium coking coal product for export."

Jan 1, 2018

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By M. K. Boateng, K. Awuah-Offei

"Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. The results show that the model is much more sensitive to the probability of imitation than the other two parameters. Thus, to reduce uncertainty surrounding the model’s predictions of community acceptance of mining, mines need to obtain accurate estimates of the probability of imitation. INTRODUCTION Mining companies have started using quantitative tools, including computer models of community interaction, to gain intelligence on social risks surrounding their projects. Models of changes in community preferences regarding mining projects over time are useful for evaluating changes in project risk due to changes in the social license to operate. For example, agent-based models that use information diffusion models and social networks are useful for studying those changes due to information diffusion. However, such agent-based models are sensitive to many input parameters including the parameters of the diffusion model and the average degree of the social network. This work evaluates the sensitivity of such a model to diffusion and network model parameters (probability of imitation, probability of innovation, and average degree) using the first order and total sensitivity indices. AGENT-BASED MODEL OF COMMUNITY ACCEPTANCE A few researchers have started using agent-based models to study mining systems (Fujiono 2011; Nakagawa et al. 2013; Bahr 2015; Boateng and Awuah-Offei 2017a, b). Nakagawa and co-workers used ABM to evaluate dynamics of a mining project’s stakeholder networks whereas Fujiono used ABM to study innovation diffusion in the mining industry. Our previous work has presented models and a framework for modeling information diffusion in a mining community and its impact on level of acceptance (a measure of SLO) of the mining project (Boateng and Awuah-Offei 2017a, b)."

Jan 1, 2018

By M. Rafieazad, P. Fathi, M. Mohammadi, A. M. Nasiri

This study examines the impact of low-temperature heat-treatment cycles on microstructure and corrosion performance of Direct Metal Laser Sintered (DMLS) AlSi10Mg_200C alloy. It is known that the morphology and the size of eutectic silicon are the two most critical factors affecting mechanical properties of the AlSi10Mg alloy. Although high-temperature heat-treatment cycles are common practice for the strengthening of the cast Al-Si-Mg alloys, in the case of DMLS fabricated AlSi10Mg alloy, high-temperature solutionizing and low temperature annealing cycles result in mechanical properties degradation primarily due to a dramatic decrease in the solubility of Si in the super-saturated a-Al matrix of the as-printed alloy. In this study, low-temperature heat-treatment cycles that only promote precipitation of Mg2Si accompanied by the interruption of the silicon network were investigated. SEM and XRD analysis were utilized to observe the evolution of microstructure after different annealing heat-treatments at 200, 250, 300, and 350°C for 3 h. Increasing the heat-treatment temperature contributed to the Si networks interruption and an increased precipitation of Mg2Si phase. Low-temperature annealing from 200 to 350°C was found to promote the homogeneity of the microstructure characterized by a uniform distribution of eutectic Si in ??-Al matrix. Additionally, in order to investigate the impact of different heat-treatment cycles on corrosion resistivity of DMLS-AlSi10Mg_200C, the potentiodynamic polarization testing and electrochemical impedance spectroscopy were performed in a 3.5 wt.% NaCl solution. The results revealed more uniformly distributed pitting attack on the corroded surface by further increase in the annealing temperature, which was attributed to the uniformity of Si dispersion. In comparison, low temperature annealing at 200°C led to a penetrating selective corrosion attack along the melt pool boundaries, resulting in a higher corrosion rate associated with the lower absolute value of impedance of the protective passive film on the surface.

Jan 1, 2018

By N. Myung, G. Hwang, H. Kim, Y. Han, S. Choi

"According to research presently being conducted on selective lithium recovery in seawater, inorganic adsorbents with high selectivity and capacity for capturing lithium ions from liquid lithium resources are called lithium ion-sieves (LISs). Their low toxicity, low cost and high chemical stability make LISs suitable for lithium recovery from seawater. In the present study, the ultrathin LMO nanofibers with controlled diameter were successfully fabricated by an electrospinning technique with a hypothesis that greater aspect ratio (i.e., smaller diameter) would lead to the enhanced recovery of lithium ion from seawater. Design of Experiment (DOE) and dimensionless analysis were performed to systematically optimize the diameter and morphology of nanofibers. Several complementary techniques including FE-SEM and XRD were used to evaluate the physical/physicochemical properties of the nanofibers. Lastly, the lithium ion recovery was tested for the nanofibers with different physical properties using lithium ion solution. INTRODUCTION Demand for lithium resources is increasing in many industries across the world.1-2 However, the conventional resources for lithium is very limited, and it even gets worse to secure the resources due to low grade and/or complexity of feed materials. Much effort has been, therefore, devoted to obtaining lithium from aqueous lithium resources. Several methods such as solar evaporation3-4, co-precipitation5, and solvent extraction6 have been proposed for recovering lithium from an aqueous lithium source, but there are limitations on its use; It takes a very long time or conditions such as temperature, pH and Mg/Li ratio are severe. Lithium ion-sieve (LIS) materials are considered as a good lithium adsorbent because of their unique chemical structure that can selectively separate lithium ion from brine and seawater.7- 10 Furthermore, their low toxicity, low cost, and high chemical stability make LIS suitable for lithium recovery from aqueous lithium resources. Spinel hydrous manganese oxide (HMn2O4) derived from spinel lithium manganese oxide (LiMn2O4) after topotactically extracting lithium from the spinel structure by acid treatment is most widely investigated LIS.10, LIS materials have been actively studied in various forms for easy handling and high efficiency (i.e. membrane11,12, foam13-14, granular15,16). Among them, the 1-D nanostructure LIS with high specific surface area is excellent in efficiency.9 In this study, we present the part of our recently submitted work17. Specifically, we fabricated systemically lithium manganese oxide nanofibers with different diameter as a lithium ion adsorbent using electrospinning technique through design of experiment (DOE). Enhanced lithium ion adsorption properties of the HMn2O4 nanofibers with different diameter were investigated in lithium liquid resources."

Jan 1, 2018

By A. Makavetskas

"The purpose of the research is to study the mineralogical features of the structure of the wall accretion formed during melting on the working surface of the walls of metallurgical aggregates and adversely affect the stability of the lining of blast furnaces (BF). We presented the results of studies of the material composition of lining and wall accretion of the furnaces of blast furnaces of the metallurgical plant specializing in the smelting of ferromanganese, nodular and pig iron. It is established that the garnissage is an aggregate of layered texture, formed as a result of the crystallization of slag and metallic melts. Refractory calcium and magnesium silicates and aluminosilicates (minerals of the melilite group, leicite, olivine group minerals) and amorphous glassy oxide solid solutions of variable composition crystallize from the slag melts in the upper part of the hearth. In the slag matrix, inclusions of carbon (amorphous and graphite) and products of crystallization of metallic melts of alpha-iron, iron carbides and / or manganese are observed. Evidence of carbon evolution (in the form of graphite) is precisely in the crystallization of metal melts, there are significant differences in the structure of carbon in coke and in the garnissage. The conducted studies confirm that it is impossible to obtain reliable information on the material composition of new formations in the blast-furnace process without using a complex of modern methods of technological mineralogy.INTRODUCTION The formation of the wall accretion (garnissage) - a solid protective layer as a result of smelting products crystallization on the inner (working) surface of the liner. This is due to the design of blast furnaces with a high-efficiency heat sink using copper coolers and the use of carbon blocks with high thermal conductivity in the lining. The objective of the study was research of the material composition of the lining and wall accretion of the blast furnace hearth of one metallurgical plant that specialized in smelting ferromanganese, nodular and pig iron, to assess the effect of new formations for stability of the lining of blast furnaces (BF)."

Jan 1, 2018

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By Lilong Huang, Yuan Long, Li Shi, Guowang Zhang, Xiao Xiao

"Graphite is the key raw material of new carbon materials such as graphene and spherical graphite. The size and completeness of graphite flakes directly affect the performance of new carbonaceous materials.The research aims to increase the yield of large flake graphite by way of preventing the flake graphite from being damaged during the grinding process. A series of grinding and flotation studies on the flake graphite samples of Yichang in Hubei Province were carried out by vertical stirred mill . The damage coefficient L characterising the degree of graphite flake fractured and corresponding formula was proposed to determine the quality of the grinding and grinding of the flake graphite. The way the damage coefficient L of graphite flake would be affected if with different mill, different media material and size, stirrer speed were investigated. The test results show that vertical screw stirred mill helps the protection of large flake of graphite as well as the graphite liberation. When grinding to the same fineness, the damage coefficient L of graphite flake is 1.20 for vertical stirred mill, while the damage coefficient is 2.93 for ball mill. Minimum damage coefficient of graphite flake was obtained when using 6 mm polyurethane coated ball as grinding media, under the condition that rotation speed of the stirrer within the range of 100~130r/min. The grade of graphite in the concentrate floated from the ground product was 94.16%, the rate of recovery for graphite was 94.66%, and the content of +0.15mm was 54.83%.1 INTRODUCTION Flake graphite is a very important non-metallic mineral[1,2],and due to its special flake structure, the greater the scale and the higher the C grade, the value of its application is larger too. Therefore, in the grinding of graphite sorting process, We should minimize the destruction of graphite scales.. In this paper, graphite mine in Yichang, Hubei Province was used as the raw material for the study. Rough concentrate with C-grade of 36.49% was prepared by rough grinding and coarse separation. Then a series of grinding and flotation studies on the rough concentrate were carried out by vertical stirred mill , which aims to increase the yield of large flake graphite and to provide technical support for improving the beneficiation process of graphite ore."

Jan 1, 2018

By Y. S. Sun, P. Gao, Y. F. Li, J. W. Yu

"Oolitic hematite ore is one of the most refractory iron ores in the world. It is not feasible to separate iron minerals from raw ore by conventional mineral processing methods. In recent years, a new technology called coal-based reduction followed by magnetic separation has been employed to produce metallic iron powder from oolitic hematite ore effectively. In order to find the nucleation mechanism, a thermodynamic analysis of the carbothermic reduction of oolitic hematite ore was conducted by the HSC 6.0 thermochemical software. The phase transition and microstructure changes during the coal-based reduction were also investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The results showed that the iron oxides in the oolitic ore were reduced to metallic iron following the route of Fe2O3–Fe3O4–FeO–Fe in reduction process. The reduction reactions preferentially occur in the high activity regions to form a higher concentration of Fe elements, and then more supersaturated Fe separated out to form new phase nuclei. Under the action of homo-aggregation and principle of minimum free energy, the iron cores continuously absorbed migratory Fe around and grew into quasi-spherical iron particles embedded in slag phase. INTRODUCTION With the rapid increase of steel industry, premium grade iron ore in China has been gradually exhausted, and its supply has become bottleneck for the development of iron and steel industry (Guo et al., 2015). Therefore, it is urgent to exploit the refractory iron ores, such as oolitic hematite ore. Oolitic hematite ore is widely distributes in France, Germany, America, Canada, Pakistan, China, and among other countries (Maynard and Van Houten, 2004; Li et al., 2011). In China, the explored reserve of oolitic hematite ore is 3.72 billion tons, which accounts for approximately 1/9 of total iron ore resources of China (Gao et al, 2016). Oolitic hematite ore possesses complex composition,"

Jan 1, 2018

By Paulo Chaves, Márcia Gonçalves, João R. S. Carvalho, Fernando J. A. S. Barriga, Edgar Carrolo, Tiago Luna, Ricardo Rato, Anabela Bento

INTRODUCTION For the last decades, deep-sea marine resources such as seabed massive sulfides (SMS), polymetallic nodules and ferromanganese crusts (Fe-Mn crusts) have received an ever- increasing amount of attention worldwide for their abundance in critical metals and potential commercial value. This interest has mostly been driven by the growing world demand for raw materials, in particular for high- and green-technology applications (e.g., hybrid and electric cars, batteries, photovoltaic solar cells, cell phones, super magnets), as well as by industrialized countries governments other than BRICS states need to secure a more diversified supply of metals, resulting in a new deep ocean exploration boom. Since the oceans and its resources are increasingly seen as indispensable for humans needs and their challenges in the decades to come, this boom increments pressure on marine areas, either in international or within countries economic exclusive zone (EEZ). Since 2002, the International Seabed Authority (ISA) has signed up 29 contracts with several entities and national governments from multiple countries (e.g., Japan, China, Germany, France, Russia, India, Rep. of Korea, UK, Canada, Brazil) for exploration for deep-sea mineral resources in international waters, either for scientific or commercial proposes, which together cover over 1.3 million km2 [1]. In turn, over 300 exploration licenses, covering more than 650,000 km2, have been granted within the EEZ of Pacific countries such as Papua New Guinea, Tonga, Fiji, Solomon Islands and Vanuatu [2, 3]. This number is expected to increase very rapidly, as 77 countries have proposed to the United Nations the extension of their continental shelf in order to extend their EEZ and jurisdiction over potential deep-sea mineral resources [4]. Its estimated that 42% of the potential areas for SMS occurrences, 54% for cobalt-rich Fe-Mn crusts, and 19% for polymetallic nodules lie within the EEZ of coastal countries [5]. In addition, a huge amount of seafloor is yet to be explored and evaluated. Combined, the size of the granted exploration areas represents less than 10% of the overall area thought as most favorable for the occurrence of the 3 types of deep-sea mineral resources above mentioned. This means that today’s assessments on deep-sea mineral resources are only a rough approximation.

Jan 1, 2018

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"At this point in time, autoclave recovery (POX) followed by sorption cyanidation (CIL) is one of the most promising technologies for the efficient processing of refractory and double refractory gold-bearing sulphide rock. This hydrometallurgical technology requires the use of a large amount of water (up to 5 tons per ton of used concentrate), resulting in highly saline water with high pH (pH 9-11), high content of cyanides (up to 300 mg/l), arsenic compounds, antimony and a number of heavy metals. In order to determine the possibility of using recycling industrial water in POX-CIL technology, several batches of experiments were conducted (using the double refractory flotation concentrate of the Mayskoye deposit). Urban water with a chloride ion content of 10 mg/l was used during the reference POX-CIL experiment as the liquid phase of the ??? feed pulp. At that, gold extraction rate amounted to 89.4 %. A full cycle of POX(200 ºC)-CIL was carried out during the first part of the experiments; at that, fresh concentrate of the untreated recycling water with cyanide ion content of 95.4 mg/l, left after the completion of the previous CIL cycle, was used for repulping. It has been established that direct use of untreated recycling industrial water is impossible due to a sharp decline in gold extraction (preg-robbing) down to 79.5%. The presence of chloride ions, cyanide ions and other ligands in the liquid phase provides effective complexion formation for the recovery gold; complex gold compounds are quickly and firmly sorbed by the natural carbonaceous substances of the concentrate at the stage of autoclave recovery; they are virtually not cyanized onwards, and gold is carried over to the tailings. During the the second batch of experiments, recycling industrial water with cyanide and chloride ions' concentration of 500 mg/l each was subjected to the reverse osmosis desalination (up to 6 times in a successive order). After each desalting cycle, such water was used as the liquid phase of the feed pulp in POX-CIL. 6 cycles of RO desalination enabled the extraction of 86.1% Au (which is close to reference recovery). During the third batch of experiments, recycling industrial water was diluted with distilled water (2, 4, 16, 32, 64 times); after each dilution cycle, this water was used as the liquid phase of the POX-CIL feed pulp. Gold extraction after 64-fold dilution amounted to 82.6%. The results of the conducted researches show that the use of untreated recycling industrial water in POX-CIL hydrometallurgical technology is absolutely impossible due to a sharp decline in gold extraction. Even the 64-fold dilution with pure water is inefficient both from the perspective of gold extraction and of rational use of water. Reverse osmosis desalination solves the problem of water treatment except for the removal of cyanide ion, which requires separate reagent treatment of water."

Jan 1, 2018

By S. M. Bradshaw, R. Smith, J. H. van Vreden, C. A. Snyders

"The re-treatment of gold tailing heaps has shown to be a potentially significant revenue stream for both large and small scale gold companies. Limited access to capital and lack of skilled labour remain restrictive especially when dealing with a refractory ore and/or where limited amount of material are available. Alternative techniques such as low temperature pre-leaching options to unlock value are therefore in demand. Several low temperature pre-leaching experiments in acidic and alkaline solutions, followed by cyanidation were performed which ultimately led to the further investigation of a caustic pre-leaching step. It was found that the Au recovery from a refractory ore tailings heap could be significantly improved from ˜ 15 to 20% to greater than 60% with a simple atmospheric NaOH pre-leaching step. It was further considered, that since the NaOH pre-leach liberate the Au associated with refractory sulphide minerals, the overall process may benefit by the inclusion of a froth flotation step to separate refractory sulphides from the free milling ore. Froth flotation on weathered tailing heaps are, however, known to be difficult, ultimately resulting in poor recoveries. A process flow sheet, incorporating a caustic pre-leaching step and a process which includes flotation and caustic pre-leaching of the concentrate, are technically evaluated and ultimately compared to simple cyanide re-processing. INTRODUCTION South Africa consists of a large number of gold tailings dumps. Janse van Rensburg (2016) estimated that there was about 517 dumps in the Gauteng area, covering approximately 320 000 ha of surface area. Recovering value from the dumps has received a great deal of interest but can be problematic due to the dumps often being refractory, preg-robbing and weathered. High recovery of valuable metals (Au and Ag) are possible (Fleming and Brown, 2010) but would most likely require pressure oxidation and subsequent neutralisation which can be very capital intensive demanding a high skill set to operate and maintain. In addition, these flowsheets target high processing tonnages due to the economy of scales at the lower grade feed materials, further increasing the capital requirement."

Jan 1, 2018

By A. H. Mumin, A. Prikhodko

"This paper provides an understanding of interpreting and evaluating airborne time domain electromagnetic (TEM) surveys as applied to massive sulfide exploration. Variations in the conductive morphologies of massive sulfide ore systems are discussed, followed by forward modelling exercises examining the derived TEM response to these morphologies and discussion of the subtleties of data interpretation. Deposit morphology in the orientation at formation and the variations occurring due to later deformation are considered. Images of corresponding resistivity–depth models are provided. The combined modelling results provide a low-cost method for initial interpretation and screening of TEM anomalies. RÉSUMÉ Cet article nous permet de mieux comprendre l’interprétation et l’évaluation des levés élec-tromagnétiques aéroportés en domaine temporel (TDEM, de l’anglais time-domain electromagnetic) appliqués à l’exploration du sulfure massif. Y sont débattues les variations au niveau des morphologies conductrices des systèmes de minéralisation du sulfure massif, suivies d’exercices de modélisation prospective qui examinent la réponse dérivée des TDEM à ces morphologies et d’une discussion sur les subtilités de l’interprétation des données. L’étude envisage la morphologie de l’orientation originelle non déformée des gisements ainsi que les variations résultant d’une déformation ultérieure. Des images des modèles correspondants de résistivité-profondeur sont fournies. Les résultats combinés relatifs à la modélisation proposent une méthode peu onéreuse d’interprétation et de contrôle initiaux des anomalies dans les TDEM.INTRODUCTION Electromagnetic geophysical surveys are an indispensable foundation of many mineral exploration programs and can account for as much as half of the predrilling exploration costs. Quantitative mass interpretation of the survey results remains difficult due to the infinite variation of deposit morphologies, their complex physical properties, and the presence of barren conductive materials that can mimic or mask the response of targeted ore. Many modern geophysical investigations that focus on time domain electromagnetic (TEM) data interpretations are devoted to problems with inversion and modelling and their algorithms. Although a few of these investigations have resulted in commercial software products, these require highly qualified and experienced users and usually include geometric assumptions. Furthermore, without the input of known physical properties and geometric constraints, the inversion results are highly ambiguous. A number of case studies document the geophysical responses to known targets in well-defined and diverse geo-electrical environments, providing a high degree of correlation between field obser-vation and the results of the modelling used in this style of investigation (Hone, 1980; Schneider & Emerson, 1980; Tyne, Idnurm, & Malone, 1981; Bishop & Lewis, 1992; Hopgood & Hungerford, 1994; Meju, 2002; Yang & Oldenburg, 2016). The uniqueness of the target/environment parameters and their specific features limits the use logy is poorly understood. The responses are therefore that are devoid of complicating environmental factors (e.g., highly conductive overburden and hostrocks or nonuniform target conductivity) as a first approach to the interpretation process of such case studies as the main reference for interpreting TEM survey responses in areas where the underlying geomodelled from generalized and typical geological models"

Jan 1, 2018

By W. D. Guo, Y. M. Zhu, B. B. Luo

The main chemical constituents of waste cooking oil are higher fatty acid glycerides, which can be used to produce anionic fatty acids for most non-sulfide flotation. However, using the mixed fatty acids (MFA) produced by waste cooking oil as collectors directly, the flotation effect is usually not satisfactory, especially at lower temperature or room temperature. There are very rare systematic studies about the reason for poor flotation performance of waste cooking oil. This study aims to investigate the flotation and adsorption characteristic of different types of fatty acids in waste cooking oil to find out what kind of fatty acids results in the poor flotation performance. This will provide technical supports and theoretical guidance for the waste cooking oil application in the field of mineral processing. In this study, MFA were produced from the waste cooking oil, and then separated into saturated fatty acids (SFA) as well as unsaturated fatty acids (UFA), which possessing different flotation properties. The properties of the MFA, SFA and UFA were analyzed by iodine value, melting point measurement, Fourier transform infrared (FT-IR) spectroscopy and quartz micro-flotation tests. The results showed that UFA was composed of fatty acids containing group—(CH=CH—CH2)n—, having an iodine value of up to 162.90, a melting point as low as -17.3 ? and stronger low-temperature floatability. In contrast, the SFA was made up with saturated fatty acids and a few oleic acids, with an iodine value of 48.97 and a melting point of 38.8 ?. SFA had shown poor collectability and required a flotation temperature higher than 35 ?. The results of zeta potential measurements, solution chemistry calculation and FT-IR spectra revealed that both UFA and SFA can be adsorbed on the quartz surface activated by CaCl2 via the chemical and hydrogen bonding. The reason MFA having a poor flotation performance is the SFA has an extremely high melting point which affecting the dissolution of the dispersion.

Jan 1, 2018

By I. Dymov

"The extractive metallurgy of precious metal ores involves gravity concentration, flotation and cyanide leaching. Pre-oxidation, such as roasting, autoclaving, bacterial oxidation and other techniques, is required for processing refractory ores. Selection of the process is mainly driven by the grade, reserve and mineralogy of the target elements. The concentrations of precious metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. The objective of geometallurgy and process mineralogy is to reduce and minimize the technical risk in project evaluation, process selection, mine planning and production forecasting through geometallurgical modelling, representative sampling and subsequent systematic mineralogical characterization and metallurgical testwork. Geometallurgy is a technique to document variability within an orebody and quantify and evaluate the impact of many factors including geology and mineralogy on grinding, flotation, leaching and metal recovery processes, while mineralogy is one of the major predictive and trouble-shooting tools for many new mineral projects and operating mines. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy and highlights the importance of both disciplines in process selection and plant optimization with applicable case studies. INTRODUCTION Precious metals, including gold, silver and platinum group elements (PGE) occur in various geological settings and ore types. The concentrations of these metals in the crust are extremely low and highly variable, resulting in ore variability in many gold, silver and PGE deposits. More importantly, precious metals in an ore may occur in two or three forms (i.e. microscopic, submicroscopic and surface-bound), making ore processing of precious metals extremely challenging. Process selection is most important in any precious metals project and is mainly driven by the grade, reserve and mineralogy of the target elements. Free-milling ores, such as Kupol in Russia, Hemlo in Canada, Grasburg in Indonesia, UG-2 in South Africa, Lac des Iles in Canada, and Noril’sk in Russia, can be processed using flotation or cyanidation with or without gravity. B2Gold Corp, a Canadian gold company, just started a number of new and under construction free-milling gold operations such as Fekola mill in Mali, Mastbati mine in Philippins and Otjikoto mine in Nambia. However, refractory ores (particularly gold ores), such as the Carlin and Goldstrike mines in the USA, Giant in Canada, Pueblo Viejo in Dominican Republic, Porgera and Lihire in PNG, Kittilla in Finland, Fairview in South Africa and Shuiyindong in China, must be processed using pre-oxidation prior to cyanide leaching. In some mildly refractory gold ores, such as Kumtor mine in Kyrgyzstan and KCGM in Australia, ultrafine grinding is required to liberate fine-grained gold particles. For some gold ores containing both free-milling and refractory components (such as Cripple Creek mine in Colorado, USA), two or more recovery processes may be required. The variability of grade, metal deportment, ore hardness and other parameters is one of the risks that encountered in development and operation of many precious metals projects. To minimize and reduce the technical risk caused by ore variability, geometallurgy and process mineralogy have been used by mining companies in the last two decades to measure and quantify the spatial variability of the deposits that are being developed. This paper presents an overview of fundamentals, methodologies and techniques applied in geometallurgy and process mineralogy, it highlights the importance of both disciplines in process selection and plant optimizat"

Jan 1, 2018