Search Documents

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the deformation-based design, construction, and performance of stone column ground improvement (GI) beneath a mechanically stabilized earth (MSE) wall and bridge abutment with heights up to 50 feet. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter- bedded with silty sand layers and organic silt where identified as being potentially liquefiable. Stone column ground improvement was designed using a deformation-based approach to address static settlement and seismic stability of the proposed MSE embankments. The deformation-based design of the stone columns resulted in significant savings over a limit equilibrium-based approach. This paper presents the results of sonic coring taken from the initial stone columns installed and compares these results to the real-time data acquisition reports from the stone column installations. Vibration monitoring results during stone column installation are included. Settlement monitoring at the face of the MSE wall and buried vibrating wire settlement monitoring elements are presented and compared to the original settlement predictions.IntroductionStone column ground improvement was implemented as a means of supporting mechanically stabilized wall approaches for a new bridge over the Puyallup River, part of HOV improvements to I-5 in Tacoma, Washington. The work discussed in this case history was part of the Washington State Department of Transportation (WSDOT) I-5/Portland Avenue to Port of Tacoma Road, Stage 1 Northbound HOV contract, developed as an early work element to a follow-on bridge construction project. The area requiring stone column ground improvement is shown in Figure 1. The improved ground supports permanent geosynthetic walls and embankments up to 50 feet high. This wall can be seen in Figure 1. The selected ground improvement primarily provides global stability of the soils beneath the walls during anticipated seismic loading and also reduces the time and magnitude of consolidation settlement under the weight of the planned embankment.Approximately 74,000 cubic yards of liquefiable alluvial soils were improved by stone columns. Stone column construction occurred in late 2010 and early 2011. This was followed by the embankment and wall construction. Settlement monitoring began with the embankment construction and continued into 2012."

Jan 1, 2017

By Suthan Pooranampillai

This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.

By Dominic Parmantier, Karen Dawson, Suthan Pooranampillai, Seungcheol Shin

"This paper presents a case study of the use of single axis cement deep soil mixing (CDSM) to deal with static settlement and seismic stability of the foundation soils under a reinforced soil slope (RSS) embankment up to 50 feet high. As part of the widening of Interstate 5 (I-5) to allow High Occupancy Vehicle (HOV) lanes in Tacoma, Washington, a new approach and span over the Puyallup River will be constructed. During the soils investigation and design phase of the project, low plasticity silts (ML) inter-bedded with silty sand layers and organic silt where identified as being potentially liquefiable. CDSM was selected to address the embankment foundation concerns and allow for future trenchless installation of utility lines beneath the embankment. The presence of a confined, artesian aquifer within the design depth of the CDSM led to the installation of a depressurization system to avoid an upward gradient through the wet soil-cement. In addition to addressing the design approach, the paper discusses the challenges associated with quality assurance of CDSM within the time constraints of an ongoing project. The limited recovery rate of conventional triple tube coring in the soil-cement and double tube wet sampling led to the use of sonic coring to provide a near continuous core of the soil-cement.IntroductionCement deep soil mixing (CDSM) was used as a replacement for stone column ground improvement in a corridor which the owner, the Washington State Department of Transportation (WSDOT) wanted to reserve for future trenchless crossings beneath reinforced soil embankments within a freeway interchange. The work was part of HOV improvements to I-5 in Tacoma, Washington. The CDSM construction occurred in late 2010 and early 2011.Approximately 14,500 cubic yards of soil cement columns were placed by CDSM. The soil cement improved ground supports permanent geosynthetic reinforced slopes up to 50 feet high. The ground improvement was designed primarily to provide global stability of the reinforced slopes during seismic loading, but it was also utilized to reduce the time and total amount of settlement following construction of the embankments.This paper presents a discussion of the design approach and challenges associated with quality assurance of a relatively small volume of CDSM within the time constraints of an ongoing project. The challenges associated with attempts at collecting cores of the cured soil-cement mix cured by triple tube coring and pushing a double tube into the wet mix and allowing it to cure insitu are discussed, along with the eventual adoption of sonic coring combined with reliance on laboratory testing of wet mix samples collected daily."

Jan 1, 2017

By Feng Yongxuan

Anchored sheep pile is normally used in deep excavations, many of which only require stability in accordance with Terzaghi theory. In this paper, based on the experience, new lateral earth pressure method is adopted taking account into interaction among soil, anchors and sheet piles so that a group for the project under very difficult conditions and very severe requirments, especially, for the displacements are determined according to that mentioned above. During and after construction, displacements monitoring were carried out for about four months, which was proved that there was a little difference between calculation and practice.

Jan 1, 1991

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By T. O. Price

In 1969 Holosonics designed and developed a portable system for conducting acoustical surveys in metal mines, with lead-silver veins as the principal targets. Recently this system has been proven useful in describing rock structures for advance geologic information in civil engineering application and underground construction applications. This paper discusses a case history of acoustical surveying from a series of pilot drill holes in an advancing tunnel. In acoustical surveying a pulsed acoustic signal is used to generate reflected signals from the rock formation. Arrival time, amplitude and phase of the returned signals can be determined. These data became the basis for a signal correlation program designed to relate the signals to their respected pseudo-planar reflecting interfaces. An application of acoustical surveying has recently been conducted in a portion of the excavation for the Washington Metro Area Transit Subway. The data results and conclusions of the program are discussed in the paper. Acoustical surveying was successful in predicting the occurrence of major jointing and foliation plane shearing ahead of the tunnel advancement.

Jan 1, 1974

By Jean Wehbe, Daniel C. Brahana

"This paper presents a case history of drilled pier construction for a new stadium in Atlanta, Georgia. The stadium structure is supported on several different foundation types, with the heaviest ""mega columns"" typically bearing on drilled pier supported mats. The project includes 141 drilled piers with design diameters of 5.5, 6 and 6.5 feet. The piers bear on bedrock at depths of 20 to 110 feet below the ground surface. Many of the piers included rock sockets with design lengths of 5 to 18 feet. A pre-production drilled pier load test program was completed including one Statnamic load test, two Osterberg Cell tests and two lateral load tests. Non-destructive testing (crosshole sonic logging and sonic integrity testing) were also performed during construction. Production pier installation with over 3800 linear feet of earth excavation and over 1350 linear feet of rock excavation was completed in a little over four months. The piers were installed using both the cased hole method and the slurry method. All cased holed required downhole inspection and slurry holes were initially inspected with a mini-SID device and subsequently by sounding. Advanced drilling equipment and tooling were used to meet the production requirements for the project. This paper reviews the highly variable soil and rock conditions encountered at the site, briefly presents the results of the load tests, and discusses pier installation procedures and the equipment used for installation. The paper also presents conclusions related to the installation and lessons learned.INTRODUCTIONWith the opening of AT&T Stadium in Dallas, a new era of stadium construction began in the U.S. The new age stadiums are larger and have more amenities than their predecessors. The new Atlanta Falcons stadium is no exception. Many of the new features, including Atlanta’s innovative retractable roof, result in extraordinary structural loads. The roof structure is supported by a series of mega columns that bear on eight large caps, six of which are drilled pier supported. Each of the pier caps contains between 8 and 16 drilled piers that bear in the underlying bedrock. The design pier diameters are 6 and 6.5 feet. Augercast piles were used to support two of the mega column caps. Drilled piers, augercast piles, aggregate piers and spread footings are used to support the more lightly loaded portions of the structure."

Jan 1, 2017

By Charles Clark, Mark Mukhija, Jaime Klein

Comminution – the reduction in size of solid materials – is the most energy intensive component of the mining process (Bauer, 2015). It is estimated that comminution consumes around three percent of all electricity generated in the world (Ceecthefuture.org, 2017). On an energy equivalent basis, downstream processing consumes six times more energy than drilling and blasting (Kanchibotla, Sarma et al., 2014).

Jan 1, 2018

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By J. A. de Carvalho Junior

This paper analyses the impact of the uncertainty associated with the input parameters in a mine planning optimization model. A real example was considered to aid in the building of a mathematical model that represents the coal production process with reference to the mining, processing, and marketing of coal. This model was optimized using the linear programming concept whereby the best solution was perturbed by the stochastic behaviuor of one of the main parameters involved in the production process. The analysis of the results obtained permitted an evaluation of the risk associated with the best solution due to the uncertainty in the input parameters.

Jan 1, 2012

By C. McAllister, D. Preece, J. Berendzen

The Multiple Blasthole Fragmentation (MBF) model was developed recently and has been reported in previous papers. The MBF model accepts inputs from the blast design, such as: location and orientation of each blast hole, stemming length, blast hole diameter, multiple decking, bench height, initiation sequence, etc. It models the effect on fragmentation of delay timing with its associated scatter for each blast hole. MBF has a statistical modeling capability for geological random variation of the attenuation of particle velocities. Also simulated is wave reinforcement due to the interaction of simultaneously arriving waves or diminishing cooperative contribution from long delay intervals between charges.

Jan 1, 2016

By Chris Leach, Lucie Spencer

This case study describes the geotechnical aspects of the basement construction for a multi-storey, residential and hotel complex located in the newly developed Elizabeth Quay precinct in Perth, Western Australia. The development included a three-level basement for car parking covering the full site area which was constructed using the top-down construction sequence. Soil conditions generally comprised 2m of fill overlying medium to dense clayey sands that in turn were generally overlying a very stiff clay stratum at approximately 13m depth. Bedrock level was generally encountered at approximately 22m to 35m below ground level. The ground water table was at a depth of approximately 1m below the existing ground surface level. A site boundary basement wall was constructed using a diaphragm wall retention system. The majority of the vertical loads from the building were transferred to the Kings Park Formation (KPF) bedrock through the use of foundation piles constructed by the CFA method. The CFA piles were installed from existing ground level, resulting in approximately 9m sacrificial concrete length from pile platform level to basement 3 (B3) level. The permanent column loads are such that a single CFA pile was not structurally adequate. To allow a full CFA foundation system to be adopted, an innovative design and construction approach was developed for these heavily loaded columns. This paper discusses the site technical details and the design and construction aspects required to meet the challenges offered by this project.

Nov 1, 2022

By Ali Keneti, Xavier Ryan, Gerardo Sanchez, Shannon Goff

In this study, FLAC3D modeling was conducted for ground-structure stability assessment for a pilot tunnel passing under a large shaft excavated in the vicinity of existing structures at Karangahape Station for the City Rail Link Project in Auckland, New Zealand. The analysis involved generation of the geometries and construction sequences in Rhinoceros®, modeling the existing ground condition, calibration of the simulated in situ conditions with the observed behavior of the ground, and excavation of the shaft and the pilot tunnel. A comprehensive interpretation of the results was then performed accompanied by comparison of the predicted behavior with the observed response of the ground during construction.

Dec 1, 2022

By Ed Mchugh

NIOSH researchers collected basic data from two blast rounds at the SSX-Steer Mine as a component of a larger study on controlled blasting, the goal of which is to reduce injuries from falling rocks in underground mines. Drilling and blasting procedures at the mine were observed. Rock mass property data were collected, a program of seismic monitoring and analysis was conducted, and 3-D laser survey scans of the workings before and after each blast were performed. The geologic data showed that the rock mass quality was characterized as poor to very poor. It was essentially uniform within the panels examined. The recorded seismic data indicated that fill material acted as an effective damper to seismic energy. The pre- and post-blast laser scans showed both over-break and under-break conditions, highlighting the problems associated with blasting a weak rock mass. By comparing the achieved results to the intended design, potential improvements in the drilling and blasting practices can be identified. Comparison of these data with similar data from other mines will help define how various combinations of rock and fill behave during blasting. Through studies such as these, data collection procedures and analysis techniques can be refined. An ultimate goal is to develop blast procedures tied to rock mass characteristics that can minimize damage to rock in the perimeter of the opening, limiting the amount of loose rock and improving the safety of miners.

Jan 1, 2007

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage organizations to work together, executing such risk assessments comes with challenges. This paper focuses on one trona mine’s experience in the development and implementation of a field level risk assessment program to help its entire organization understand and manage risk to an acceptable level. Through a transformational process of ongoing support and communication, Solvay Green River fostered a culture of trust and safety grounded in risk assessment, safety interactions, and hazard correction. The application of consistent risk assessment (RA) tools was critical to create a participatory workforce that not only talks about safety, but actively identifies energies that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s process of RA implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks. As discussed, consistent efforts to establish a participatory risk management program are worth the initial struggle to ultimately reduce incidents. INTRODUCTION Work-related health and safety (H&S) incidents often account for lost days on the job, contributing to organizational/financial and personal/social burdens [1-2]. Accompanying research demonstrates that risk and ambiguity around risk contribute to almost every decision that individuals make throughout the day [3-4]. In response, understanding individual attitudes toward risk has been unquestionably linked to predicting H&S behavior [5]. Although an obvious need exists to identify more comprehensive methods to assess and mitigate potential hazards, some argue that risk management is not given adequate attention in occupational H&S [6]. Additionally, research suggests that a current lack of knowledge, skills, and motivation are primary barriers to mitigating workplace risks [3-6]. Therefore, enhancing knowledge and awareness around risk-based decisions, including individuals’ abilities to understand, measure, and assign levels of risk to determine an appropriate response, is increasingly important in hazardous environments to predict and prevent incidents. This paper focuses on tailored approaches to field level risk assessment (FLRA), measurement, and common barriers to participating in such activities. The authors use a trona mine in Green River, Wyoming, as a case study to illustrate how the organization overcame widespread and site-specific challenges to implement a proactive risk management program. By discussing the mine’s tailored FLRA program, this case study contributes to the literature by first, providing examples of critical components that need to be in place to ensure successful risk management and second, context for continuous quality improvement that can foster a higher level of trust and empowerment on site."

Jan 1, 2017

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2017

By R. Heiser, J. Vendetti, B. P. Connor, E. J. Haas

Health and safety indicators help mine sites predict the likelihood of an event, advance initiatives to control risks, and track progress. Although useful to encourage individuals within the mining companies to work together to identify such indicators, executing risk assessments comes with challenges. Specifically, varying or inaccurate perceptions of risk, in addition to trust and buy-in of a risk management system, contribute to inconsistent levels of participation in risk programs. This paper focuses on one trona mine’s experience in the development and implementation of a field-level risk assessment program to help its organization understand and manage risk to an acceptable level. Through a transformational process of ongoing leadership development, support and communication, Solvay Green River fostered a culture grounded in risk assessment, safety interactions and hazard correction. The application of consistent risk assessment tools was critical to create a participatory workforce that not only talks about safety but actively identifies factors that contribute to hazards and potential incidents. In this paper, reflecting on the mine’s previous process of risk-assessment implementation provides examples of likely barriers that sites may encounter when trying to document and manage risks, as well as a variety of mini case examples that showcase how the organization worked through these barriers to facilitate the identification of leading indicators to ultimately reduce incidents.

Jan 1, 2018

By Debasis Barman

TBM (TBM) mining in urban areas particularly under low overburden is a big challenge to design and excavate. During excavation of the Lucknow Metro project, in Uttar Pradesh, India the metro authorities encountered a design stretch where the TBM had to cross a sewer canal crossing of 15 m length under overburden of less than 1 m. Not only the stability of TBM due to uplift was of concern but also the stability of both banks. Most structures on the canal banks were non-engineered structures whose stability due to vibration of TBM was also of concern. Due to these risks, a method was proposed that met stability requirements for both ground and superstructures. The design was practical and cost effective to construct, and a collaborative exercise between the client, contractor and designer that took approximately 18 months to implement.

Jun 13, 2023

By Douglas F. Scott

This case study provides an example of how social marketing was applied to meet the needs of business customers. Federal regulations require that all companies develop a written program to track hazardous chemicals at their sites. The HazCom Writer, created by the National Institute for Occupational Safety and Health (NIOSH), is a software tool designed to help companies prepare their required Hazard Communications (HazCom) written plan and list all hazardous chemicals at the company's worksite. The social marketing goal was to provide a product for small- to medium-sized companies to use for federal HazCom rule compliance. The HazCom Wm'ter is a direct NIOSH response to customer and stakeholder needs (including the Mine Safety and Health Administration, the mining community, and Occupational Safety and Health Administration- regulated companies).

Jan 1, 2009

By K Young, M Martin, D Payne

This paper outlines the evolution of managing high consequence risk scenarios in BHP Coal, with particular focus on managing the stability of an endwall that is adjacent to a public infrastructure corridor running through a Central Queensland coalmine. BHP Coal developed a Geotechnical Consequence Register after industry failures identified shortcomings in traditional risk assessment practices. Traditional risk assessments consider the consequence and likelihood of a geotechnical event occurring under normal operational conditions. As such, the risk rating for a high consequence, low likelihood failure may fall within the acceptable range, even where a lack of meaningful geological data exists due to the area being off lease or outside of mining reserves. The Geotechnical Consequence Register lists all geotechnical failure scenarios of high consequence, identifies if current controls are adequate, and highlights if specific Geotechnical Management Plans are required. This case study reviews a failure scenario that was identified through the geotechnical consequence register. The scenario had previously been considered low likelihood and subsequently driving a low risk; however, the likelihood ranking was impacted by a lack of geological data outside of the mining lease and predominately informed by an acceptable historical slope behaviour. Additional exploration identified previously unmapped faulting which increased the risk rating. The requirement to develop a specific management plan resulted in an increase in the required factor of safety, design changes, the implementation of additional monitoring and a corresponding monitoring Trigger Action Response Plans (TARP). In the case study area, the initiation of a geotechnical instability was identified early through the increased monitoring program. The instability was successfully managed and any impact to the infrastructure corridor off lease was prevented. BHP Coal has used the Geotechnical Consequence Register for several years to identify and assess high consequence geotechnical failure scenarios. In some areas this has justified additional exploration, more stringent design acceptance criteria and an increased level of geotechnical monitoring. The process has been successful in ensuring that geotechnical risk is controlled in areas that often receive less attention than active production areas.

Nov 29, 2022