Search Documents

By T. Feroze, B. Genc

"The effect of some of the system variables in forcing and exhausting ducted fan systems on ventilation in an empty heading was investigated using computational fluid dynamics(CFD) and comparative analyses. The diameter of the duct, duct mouth to face distance, and the power of the fan (quantity delivered by the fan) were varied and their effect on ventilation determined through a comparative analysis of the flow rates calculated close to the face of the heading. Estimation models were developed, which can be used to calculate the flow rate close to the face of the empty heading for different settings of the system variables studied.The study showed that recirculation for a forcing ducted fan system can be reduced by increasing the duct diameter or increasing the duct mouth to face distance. For the exhausting ducted fan system, higher flow rates were achieved by reducing the duct mouth to face distance, andincreasing the fan design flow rate and duct diameter.The outcomes of this investigation will help ventilation engineers in deciding the optimum duct fan system required for sufficient ventilation.IntroductionThe ventilation of underground mines, irrespective of the type of mine and mining method, is divided into two broad branches, the primary ventilation and secondary or auxiliary ventilation. The primary ventilation is responsible for the total volumetric flow through the mine and the auxiliary ventilation is responsible for the ventilation of the development ends, production areas, and facilities disconnected from the main circuit with no through-ventilation connections. Auxiliary ventilation is the more difficult to achieve (Bise, 1996), and the disruption of this ventilation system is considered to be one of the primary factors contributing to methane and coal dust explosions (Creedy, 1996). A number of causalities have been recorded by many authors due to these explosions (Phillips and Brandt, 1995; Dubinski et al., 2011; Phillips, 2015). The ventilation of short headings, less than 10 m in depth, can be carried out without the use of any auxiliary equipment (Feroze and Phillips, 2015). However, for headings deeper than 10 m, auxiliary ventilation systems are required. These are generally classified into the three basic types, namely line brattice (LB) ventilation systems, ducted fan systems, and jet fans (Figures 1 through Figure 3 respectively)."

Jan 1, 2017

By Peter Cain

In 1993 an opportunity presented to monitor the effects of undermining an abandoned roadway by a longwall panel in the Sydney. N.S. coal field. Interaction subsidence data was collected by survey leveling to benchmarks in the undermined gateroad as well as by a standpipe system equipped with 15 vibrating wire piezometers measuring changes in elevation in the gateroad relative to an outby header tank. The piezometers were monitored at 30 minute intervals using a datalogger. while the leveling surveys were conducted weekly over the life of the project. The monitoring program resulted in the collection of a very large both of data. relating vertical subsidence to the relative position of the underlying face. The most basic analyses derived a travelling subsidence curve from the leveling data only. which hinted at a relationship between rate of extraction in the panel below and the amount of strain developed in the undermined strata. The complexity of the relationships between the amount of subsidence obtained, the location of' the individual monitoring stations, the rate of face advance below and the potential for "periodic" subsidence due to geological conditions has made analysis difficult. and the amount of data has compounded this problem. Recently. an analytical approach using a commercial neural network analysis package has been applied. which appears to have resulted in the ability to draw sonic meaningful conclusions from the data set. In this paper a short history regarding the collection of the data set is followed by a brief' description of neural networks. This is followed by a description of the several analyses performed. some of the results obtained, and conclusions drawn.

Jan 1, 1998

By S. Klingmann

ABSTRACT In this paper, we used data collected from the Gibraltar mine to analyze the effect of the TyreSense tire monitoring system on tire performance by reducing tire wear and preventing premature tire failure or damage. We analyzed the relationship between tire temperature, tire pressure, and tire failure or damage to help better understand the importance of controlling high tire temperature and pressure. The results enhance and expand the knowledge of the management of tire operational pressure and temperature.

Jan 1, 2014

By M. Board, R. Pakalnis, S. Seldon, R. Brummer

The Kidd operation mines roughly 10 000 tpd of copper and zinc ore from underground and employs about 700 personnel. In the late summer and fall of 1997, major movements in the proximity of the east wall of the Kidd open pit had been observed. The Kidd pit had been mined from 1965 to 1977 to depths of 260 m (850 ft), followed by subsequent mining by underground methods to current depths in excess of 1830 m (6800 ft). The No. 1 Mine (2600 Level to pit bottom) is approximately 90% extracted, with most of the remaining reserve between 2000 and 2500 levels. Although initial concerns centred on the stability of the pit walls, the potential ramifications of the movements to the underground were recognized and measures were implemented to ensure the safety of personnel as well as to minimize the potential damage to existing operations. In late October, damage to underground operations was observed as deep as the 2000 Level. In the final assessment, the global mobilized mass was a “wedge”-shaped hangingwall block extending from surface to about 610 m (2000 ft) below surface. The “wedge” boundaries are defined by a fault and shear zone which have continuous lengths in excess of 1070 m (3500 ft); its base by shearing through the host rock mass; and its eastern face by deep tension cracks (Fig. 1). Mined and filled excavations at the western face of the “wedge” allowed mobilization of a mass in excess of 30 M tonnes. Movements in excess of 75 cm (30 in.) per day were recorded on the surface stations that preceded the complete shutdown of operations on October 29, 1997. The evaluations in the days following the shut-down were centred on mitigation of immediate and future possible negative impacts on infrastructure and mining of the remaining No. 1 Mine reserves while ensuring the safety of the operators. This effort required the rapid assessment of the potential damage of the block movement on underground infrastructure, stope access, drainage and ventilation, as well as airblast potential due to the falling of a large block into the pit near the ventilation intake at the base of the pit. These assessments were presented in a previous paper (Seldon et al., 1999). In total, the lateral movement of the block on the ground surface was over 4.3 m (14 ft). This paper describes the detailed studies performed to understand the failure mechanism and to assess the impacts on future mining in No. 1 Mine.

Jan 1, 2000

By J. Alexandre

The use of bricks of soil-cement is proving to be an important constructive methodology due to low environmental impact in the production process of these blocks comparing with conventional bricks are burnt, besides being easy to produce. However during the process of production of bricks, which are compressed, knowledge of the properties of the soil used is critical to the quality and durability of the blocks. The objective of this work is to evaluate the feasibility of using soil from the municipality of Goytacazes for the production of soil-cement bricks. Assays were performed the compaction, liquid limit, plastic limit, particle size analysis, EDX and X-Ray diffraction for later pressed blocks and analyze their compressive strength and water absorption.

Jan 1, 2015

By M. K. Patel, K. C. Wade, M. Cross

In the past decade a good deal of effort has gone into the computer simulation of the heat distribution of pellet induration systems. The major uncertainty in the analysis of such systems is the gas flow distribution and, in particular, the role of leakage. Evaluation of the leakage into or out of a zone has proved to be very difficult, as has the cross-flow from one zone to another when adjoining zones have gas flows which change direction from up draft to down draft for example. This paper describes an initial model to calculate the gas flow distribution in a variety of practical situations of interest to those involved in pellet induration. The model is based upon a multiphase CFD code called CASCADE which is used in conjunction with the pellet induration simulation INDSYS.

Jan 1, 1990

By T. C. -M. Cheng

Iron removal and disposal in zinc plants has imposed a major environmental challenge to the industry. Among the existing options of precipitating iron as jarosite, goethite, and hematite, the Hematite Process seems to be the best candidate for the future development of a waste-free technology, because of its potential of producing saleable iron oxide residues for feed in iron-steel making industry. Unfortunately, under the current practice of the Hematite Process, it is not possible to produce iron residues clean enough to meet the specifications of the said industry. In this paper, the practice of industrial hematite precipitation and the relevant technical literature are reviewed with the objective to identify the critical processing parameters which are responsible for the contamination of hematite, particularly with sulfur and zinc. The analysis is conducted from a crystallization theory standpoint with emphasis given to the role of supersaturation with respect to the cleanliness of hematite precipitates.

Jan 1, 1997

By Emad Iskander

The seepage forces generated around pressurized water tunnels in rock are investigated using the analysis tools of geomechanics. The theoretical background of the two-phase material behavior is explained and the equations of motion and continuity are presented. Applications on two case studies typically occurring in practice deal with the required minimum rock cover for a pressurized tunnel and the separation between two tunnels carrying different heads. The rock mass behavior as described by the Mohr-Coulomb and Hoek-Brown material models is investigated by numerical analyses and the results are compared. The effect of key material parameters on the safety factors and the associated modes of failure is discussed.

Jan 1, 2008

By Hapsari Rosa, Ross Cowie

Conventional blasting activities in the mining process use various types of explosives, with the primary raw materials being Ammonium Nitrate and diesel fuel. The quality and specifications of the two raw materials significantly affect the performance of explosives. One program from the Indonesian Ministry of Energy and Mineral Resources requires mixing 30% Bio Diesel 30 with 70% diesel fuel oil in several industrial sectors, including mining, to reduce greenhouse gas emissions and stabilize CPO prices. This program aims very well for environmental sustainability and the palm oil business. However, it turns out that this change impacts the performance and results of the blasting process in the mining industry, which is the appearance of fumes. This paper will discuss the tests carried out in the laboratory on Bio Diesel 30, the explosive products used, and rock samples were taken from a mine in East Java, Indonesia. The aim is to determine what factors can cause fumes utilizing a mixture of Bio Diesel 30 with pure diesel fuel. The parameters tested were visual differences, infrared spectrometry, density and viscosity, surface tension and contact angle for Bio Diesel 30, stability test for explosives, and the SEM-EDS method for rock samples.

Feb 6, 2023

By J. Miller, B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand, and gravel (SSG) sector in the USA. Researchers from the National Institute for Occupational Safety and Health (NIOSH) are currently conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine. A validated numerical model was used to explore the potential behavior of the pillars and roof as loading conditions change. The validated model was used to compare changes in mining sequence, overburden depth, and the in situ stress field. This will allow mine operators and engineers to have a better idea of the conditions that could be encountered as mining progresses. Results from the numerical modeling indicate that roof displacement more than doubles as the vertical stress increases from 10 MPa (1450 psi) to 19 MPa (2750 psi) when the maximum and minimum horizontal stresses were 41 MPa (5950 psi) and 22 MPa (3190 psi), respectively. Consequently, as the pillar load increases, the safety factor of the pillars is projected to decrease by about 25%. The impact of the practical application of numerical models can result in a reduction of ground-fall accidents and injuries as well as generally safer working conditions.

Feb 2, 2021

By B. Slaker, M. M. Sears, G. Rashed

Ground falls represent a significant hazard at underground mines in the stone, sand and gravel (SSG) sector in the United States. Researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) are conducting detailed investigations into the complex loading conditions at underground stone mines operating in challenging conditions. This paper presents the application of numerical modeling to analyze pillar and roof stability at a dipping underground limestone mine.

By S. K. Pan, R. Venugopal, L. A. Kumaraswamidhas, Rakesh Prasad, Chandan Pandey

Cold compressive strength (CCS) and apparent porosity (AP) of pellets are essential properties regarding the burden of blast furnaces. The optimal required values for industries are 2.5 KN CCS and 21% AP. Blaine fineness and firing temperature are the decisive parameters analyzed here. During firing, microstructure phases such as silicate, hematite, and pore are formed. The phase’s grain density during induration influences the pellet’s CCS and AP. The influence of the factors over the response is evaluated by I-optimal (response surface methodology) design. Blaine fineness, firing temperature, pore phase grain density (PPGD), silicate phase grain density (SPGD), and hematite phase grain density (HPGD) affect the CCS and AP of pellets. The RSM-I-optimal predicted responses with a coefficient of determination (R2) of 0.89 for CCS and 0.91 for AP of iron ore pellets. Optimal conditions were Blaine no. = 1668 cm2/g, 1250 °C firing temperature, PPGD value 90 no/mm2, SPGD value 250 no/ mm2, and HPGD value 490 no/mm2, with 4.5 KN CCS 27%. The induration processes were investigated through statistical design of experiments for process optimization. Statistical analysis indicated the direct and interactive influence over CCS and AP. In this study, RSM-I-optimal modeling is used for iron ore pellets processing. The I-optimal prediction could be applied to make the process economical because information is obtained through fewer experiments.

Aug 18, 2020

By Shahé Shnorhokian

Remnant pillars evolve towards the latter stages of mining in an orebody and act as repositories of mining-induced stress. It is therefore crucial to plan ahead as to their dimensions and location with respect to the local geology. A case study of a Canadian base metal mine was examined for the planned mining sequence scenario to identify the stress regimes acting on a future remnant pillar occurring between levels 4800 and 5100, near a brittle dyke. A mine-wide model was constructed in FLAC3D and input parameters included results from field measurements of the direction and magnitude of the principal stresses, and the geomechanical properties of the different formations. Prior to the study, the model was calibrated based on a 6-year record of mining-induced seismicity and rockburst events, focusing on large event clusters. The mining sequence followed at the mine was then used in the model to study the planned future extraction program around the remnant pillar. It is shown that the distance of the remnant pillar from the dyke and another orebody plays an influential role on the stress levels developed in the pillar.

Jun 1, 2012

By Gennaro G. Marino

Documented case histories of surface ground movements from mine subsidence were utilized to help determine when the initial collapse of the overburden occurred above longwall panels. By studying this relationship between initial movement at the surface and the amount of face advance, the least-complex conditions exist for empirically assessing the span capacity of the overburden. The objective of this work was to obtain a better understanding of the overburden response to longwall mining. This knowledge will give a better insight on the long-term effects that different overburden types have on the stability and the subsidence potential of room and pillar mines, as well as, the influence of the overburden on subsidence over longwall panels. Theory on the overburden span capacity was developed and correlated to field observations. Data were used on the overburden lithology, depth, width, and face advance of the panel, and the subsidence conditions that were noted on the surface. The subsidence measured on the surface was used to determine when complete failure in the overburden rock had occurred. According to spans predicted by theory and the subsidence measured in the field, the competent lower units failed at a face advance less than when significant subsidence was observed on the surface. In each case studied, there were competent lower beds; however, the full overburden weight was not sustained to the point of subsidence. The best correlation with the surface movement was found with the most shallow, competent bed. Elastic plate solutions with various support conditions were found to best monitor the surface subsidence of these upper roof units.

Jan 1, 1988

By L. G. Austin

"This paper is based on the development of the Maza-Austin technique for characterizing thousands of coal particles by approximate analysis of the major inorganic constituents Ca, Al, Si, K, Na, Fe and S in each particle. The technique has sufficient sensitivity to work on small volumes, is fast enough to handle large number of particles within a reasonable period of time, and consists of scanning electron microscopy combined with energy dispersive x-ray spectrometry (SEK-EDS). A computerized SEK-EDS system that allows the automated analysis of hundreds of coal particles per hour' is described. The analysis is based on the location and tracing of coal particles embedded in a polished specimen, the selection of sampling points on the traced particles, the collection of an x-ray spectrum from each sampled point for a defined period of time, and the processing of the x-ray intensity to calculate point composition using ZAF corrections. Procedures for correcting for dead time, background, detector efficiency and spectrum overlap are described. These corrections are essential if reasonably accurate analyses are to be obtained from unknown complex mixtures of the elements in a coal or fly ash particle. Examples are given. INTRODUCTION Coal is a complex mixture of organic and inorganic materials. The inorganic fraction is referred to as mineral matter (Gluskoter, 1978) but can occur in three modes: (i) an observable mineral species; (ii) as cations held by ion exchange to carboxylic groups; and (iii) in chelate complexes. The mineral matter content normally represents a significant proportion of a coal, with an average value of about 15% for US coals (Gluskoter, 1975). The standard methods of analysis of the mineral matter in coals are performed on a sample selected to represent the whole coal as closely as possible, and give the overall inorganic composition in the coal. Such analyses are of limited use for solving problems originating from the behavior of individual coal particles, whose compositions vary widely from the average value. This is particularly true in pulverized coal combustion, where the current methods of predicting the slagging and ·fouling potential of a coal are based on the bulk ash composition, but the fly ash particles which create the deposits originate from coal particles with large differences in mineral compo1ition. Some examples can be found where, in a comparison between two coals, the one with the smaller slagging potential according to the mean ash composition was the one that behaved worst in the furnace (Moza et al., 1980; Koza and Austin, 1983). The u1e of gravity fractionation to assess the slagging potential of pulverized coals has shown that conventional ASTM analysis is not sensitive to differences in the distribution of mineral matter when comparing coals (Borio and Narciso, 1979). Bryer (1979) concluded that coals should be examined for fouling and slagging potential by analyzing gravimetric and size-fractionated coal, preferably pulverized· and ground to the size expected at the mill outlet."

Jan 1, 1989

By John Owens, Hamid Maleki

Efficient and safe use of mobile roof supports (MRS) depends on the interaction between the MRS and coal strata. Of particular interest to this study are the mechanics of strata deformation as influenced by geologic conditions, pillar extraction methods, and MRS load-bearing capabilities. To provide a better understanding of the mechanics of strata deformation, the authors have collected and reviewed measurements of convergence and stress in one western U.S. mine and have completed pseudo-three-dimensional, boundary-element modeling for two typical pillar-pulling plans. Stress distribution in the mine roof above pairs of MRS’s was calculated to demonstrate how MRS’s contributed to the control of roof block movements. It was shown that overall stress and roof-floor convergence patterns were most influenced by the stiffness of coal-measure rocks and by pillar-pulling sequences and layouts. MRS’s and other support systems play a critical role in controlling the stability of both the immediate roof and the middle roof for a distance of up to 18 m (60ft) above the seam. MRS’s provide unique ground control advantages over other types of secondary support by significantly reducing the time between mining and installation of secondary support. Although MRS’s are similar to posts in stiffness and capacity, they are more effective than posts under static loads because they can yield and still maintain loads at near-peak capacity, whereas posts fail and loose their ability to limit mine roof deformation.

By Dragomir Gospodinov, Savka Dineva

A surprisingly large mining-induced seismic event occurred in the LKAB Kiirunavaara Mine (Sweden) on 18 May, 2020 at 03:11 (local time). The estimated moment magnitude was 4.2. The event caused extensive damage in a large section of the mine. The production in the area is not yet resumed, even by the beginning of 2022 (~20 months after the event). The Kiirunavaara Mine has one of the world’s largest underground seismic systems with approximately 253 geophones. The in-mine records of the event showed a very complex character with a several sub-events. The event was also well recorded by seismic stations out to over 9,000 km distance. Data from the underground and regional seismic systems were analysed to define and compare basic source parameters such as hypocenter location, seismic moment, as well as the seismic moment tensor. The data from the in-mine seismic system was used to study the development of the seismic process and to define elementary seismic sub-sources together with the official hypocenter location.

Apr 26, 2022

By S Basu, S L. A Gowravaram

CaF2 has been a common constituent in a wide variety of welding fluxes, including those used for submerged arc welding (SAW). The widespread use of CaF2 stems from its role in lowering the liquidus temperature as well as the viscosity of the molten slag that covers the weld pool. However, the harmful effect of fluoride evaporation from molten flux, on the environment as well as the health of the users is becoming increasingly evident over the years. This has led to increasing attention towards reducing the CaF2 concentration in the fluxes. The fluoride-free formulations face the challenging requirement to maintain the thermo-physical properties (viscosity, liquidus temperature etc) like those observed in fluoride-containing fluxes. In the present work, three fluxes with compositions in the CaO-MnO-SiO2-Al2O3 system have been identified as promising alternatives to the CaF2-rich fluxes. However, the thermo-physical properties of any such flux need to be comparable to CaF2-based commercial SAW fluxes before it can be adopted for regular use. The single hot thermocouple technique (SHTT) has been used by several researchers in the past as a tool for observing the melting and solidification characteristics of fluxes. This device has been developed in the present work and is used to characterise the melting behaviour of the fluxes. The measured solidus and liquidus temperatures from SHTT were compared with the results from differential thermal analysis (DTA) and simulations using the FactSage™ software for a comprehensive understanding. In spite of having a slight deviation in the measured values from the multiple techniques, the results obtained from these multiple methods show that the selected compositions could be potential CaF2 free alternative welding fluxes.

Jun 19, 2024

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By D. M. Dabbs

A static dew point technique has been used to evaluate the solubility of arsenic in ?slag and its dependency on P02 at temperatures of 1458 and 1523K. The ferrous-ferric ion ratio of the slags ranged from 3.9 to 23.8. These values correspond to partial pressures of 02 ranging from 10-8 to 10-12 atm. The solubility of arsenic in slag was found to be independent of? P02? The data indicate that elemental arsenic exists in silicate ?slags. This result was further substantiated by mass .spectrometric analysis of doped slag specimens.

Jan 1, 1983