Search Documents

By Isa Nozari, Asghar Azizi

The extraction of copper from sulfate leaching liquor was investigated using Acorga M5640 commercial extractant in kerosene diluent. The effects of important factors such as the extractant concentration, contact time, liquor pH, and temperature were examined on the separation factor Cu/Fe and the extraction efficiency of copper. The results indicated that nearly 92.32% copper was extracted from the leach liquor at 10% (v/v) Acorga M5640 concentration, 1:1 aqueous/organic phase ratio, 20 min contact time, pH 2.5, and 25 °C temperature. Also, the further increase in the values determined had no positive impact on the extraction of copper. Under these conditions, the separation factor Cu/Fe was obtained about 29.64. The extraction mechanism was studied applying the plot of log(D) – 2 pH against log [extractant] and it proved the association of two moles of Acorga M5640 for the extraction of one mole of copper. McCabe–Thiele diagram was constructed and a single-step extraction process was found to obtain themaximumextraction. Additionally, thermodynamic datawere investigated and the extraction process was endothermic and non-spontaneous at 298 K (ΔH = 27.05 and ΔG = 15.52 kJ mol−1). Moreover, the loaded organic phase was stripped and 80.94% copper was recovered after 20 min using 10% sulfuric acid concentration.

Jul 31, 2020

An Investigation into the Flotation Behaviour of Pyrrhotite Present in the Merensky Orebody

Sep 13, 2010

By Bruno Bussière, Guosheng Zhan, Michel Aubertin, Vincent Martin, Robert P. Chapuis

The study evaluates the hydrological behaviour of exposed and covered waste rock dumps. The objectives were to determine the major factors influencing unsaturated flow in waste rock dumps and covers, and to improve the in-situ, laboratory and numerical modeling characterization methods. Using material properties obtained from in-situ and laboratory tests, waste rock dumps of different configurations, with and without covers, were modeled. It was found that a properly designed “Store, divert and release” (SDR) cover allows most of the water to be diverted downslope and discharged outside of the waste rock dumps. The SDR cover seems to work efficiently even in extreme storm events. The numerical modeling results show that the unsaturated hydraulic properties (e.g. air entry value and water entry value) of the materials largely control the infiltration of water into waste rock dumps.

Jan 1, 2005

By M. J. Nicol, R. P. Colborn

An investigation into the kinetics and mechanism of the oxidation of iron (11) by oxygen in aqueous chloride solutions By R. P. COLBORN Pr. Eng., Ph.D. (Natal) and M. J. NICOLt B.Sc. Hons., Ph.D. (Rand) A reaction mechanism for the oxidation of ferrous chloride by molecular oxygen is developed. and the appropriate constants are evaluated. The effect of a number of cations and anions on the rate of oxidation has been tested.

The aim of this research was to study the absorption characteristics of thermally dried fine coal from South African collieries. After milling to ?150 µm and pressure filtration, the samples were subjected to either air drying or thermal drying at 150°C. The samples were then put into a climate box at 28°C and at three different relative humidity levels, namely 30, 60 and 94 per cent. It was found that the equilibrium moisture content of thermally dried coal at a specific relative humidity was lower than that of air dried coal. The relationship between the equilibrium moisture content and relative humidity is described by 1 ? RH = exp (-KTMen). There was no relationship between the volatile matter content and equilibrium moisture content, but there was an increase in the equilibrium moisture content of the coal with an increase in mineral content. The moisture uptake rate increased with an increase in temperature and a decrease in particle size. A model is discussed that fitted the experimental data and gave a good prediction for changes in the conditions. There was no evidence of greater moisture absorption by thermally dried coal. Keywords: Fine coal, thermal drying, drainage, South Africa, drying

Jan 1, 2002

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By M. C. Bhulose

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The purpose of this project was to identify constraints that could occur in the current sub-decline shaft at Turffontein Shaft should an increase in production take place. Particular attention was to be paid to the transportation of men and materials and to the broken rock and ventilation capacity of the shaft. This project is an in-depth evaluation of the logistic capacity of the sub-decline system at Turffontein Shaft in order to determine by how much production can be increased in this area to replace tonnages from the vertical shaft area, where ore reserves are rapidly becoming depleted.

Jan 1, 2004

By M. Karmis

The determination of the surface area which may be impacted by underground mining is an important consideration in subsidence engineering. A number of parameters have been utilized to identify this influence area, most notably the angles of draw and break. This paper discusses the implications of selecting an appropriate "damage angle" for defining a potential damage area due to mining, within which surface structures may be impacted Furthermore, the influence of both mining and geological factors, such as mining width and depth and overburden lithology, on this angle is examined, using the Surface Deformation Prediction System (S.D.P.S) software. Finally, recommendations are given for applying these concepts in subsidence control.

Jan 1, 1994

By R. Shamsodini, A. Poor Zaeif Doost, H. Haji Amin Shirazi, M. R. Garmsiri

"With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.INTRODUCTIONThe flotation circuit at Miduk Copper Complex consists of five flotation columns as roughers and ten mechanical cells as rougher-scavengers. According to design criteria, 75% of the final product was expected to be produced by the rougher columns, while most of the feed consisting of liberated valuable particles is introduced into rougher-scavengers. To liberate locked particles, the rougher-scavengers concentrate is introduced into the regrinding circuit (see Figure 1 below). The regrind mill is in reversed closed circuit with a secondary hydrocyclones cluster, and the cyclone overflow is introduced into three parallel cleaner columns. Cleaners concentrate reports to concentrate thickener and the column tailings is introduced into six mechanical cleaner-scavenger cells. The cleaner-scavengers concentrate reports to the regrind circuit(Figure 1)."

Jan 1, 2012

By M. C. Harris

"Excess Gibbs energy is a thermodynamic parameter which quantifies the difference between the value of the Gibbs energy for a real mixture and that for an ideal mixture. More specifically the partial molar excess Gibbs energy of a species (i) in a mixture is indicated by the change in the overall excess Gibbs energy of the solution as the number of moles of species (i) changes while keeping temperature, pressure and the number of moles of all other species in the solution constant. Generally it is obtained from the activity coefficient which in turn can be obtained for a species in a mixture using a variety of models. The most widely used method is to use UNIFAC. Flotation is probably the most important process in the concentration of minerals and requires the use of reagents such as collectors and frothers. There is abundant experimental data which illustrates that collectors of different alkyl chain lengths will change the contact angle and that frothers of different structures and molecular weights will result in changes in key flotation properties such as froth behavior, surface tension and critical coalescence concentration. In this paper it is shown that there is a strong linear relationship between measured parameters such as froth volume/height, surface tension, critical coalescence concentration and contact angle and the partial molar excess Gibbs energy of the molecules used. Proposals are made to explain these correlations.INTRODUCTIONAs is well known froth flotation is arguably the most widely used process in the separation of minerals. In broad terms the process relies on the use of reagents known as collectors to adsorb onto a mineral surface and thus render the mineral particle hydrophobic. Alkyl thiolates are very commonly used for this purpose. The hydrophobicity is induced as a result of the alkyl group’s molecular structural properties which results in it forming a non-ideal mixture with the process water. Surfactants (or frothers) are typically alcohols and are known to lower the surface tension of the system and also inhibit bubble coalescence and reduce bubble size. Since alcohols are polar they will also form a non-ideal mixture with water. The hydrophobic mineral attaches to the bubble and rises to the froth phase where the valuable mineral is recovered as a concentrate. Frothers have often been characterized using the so-called HLB (hydrophobic-lipophilic balance) number but recently it was shown that the use of activity coefficients (?) or excess Gibbs energy (G ex ), which is calculated using equation (1) is a much more appropriate way to describe the behavior of these reagents in non-ideal mixtures with water (Corin and O’Connor, 2014)."

Jan 1, 2016

By J. P. Sairrlon, K. G. Wheeland, K. J. Mintz, B. J. Kiener

Iwenty-one ore dusts of varying mineralogy, sulphur content and reputed in-mine explosibility were selected from eight mines. After chemical and mineralogical analysis and sieving into two size fractions (+45/ -63 microns and -45 microns), these sarrples and seven pure minerals were tested for explosibility in oxygen in a Harbnann chamber. '!he maximum explosion pressures and maximum rates of pressure do not correlate with sulphur content alone; the types of minerals are also .important. Residues were analyzed to check the combustion reactions. Further comparisons between laboratory and mine results are planned to improve predictability.

May 11, 1988

Common brattice cloths in use in Australian coal mines are compared by permeability measurements. The respective advantages of twill weave and tarpauling* weave cloths are listed, and the improvements to be obtained in the ventilation of a mine by using tarpauling cloths instead of the commonly used twill cloths are stressed. Plastic cloths are widely used overseas and are briefly discussed.INTRODUCTIONThe onset of extensive full-scale mechanization in Australian coal mines during the past few years has increased attention given to the ventilation of working places. Many inadequacies of the present system have been brought to light and not the least of these is connected with the use of brattice cloth, both in directing the flow of air around the face and in acting as a temporary sealing mechanism. A well-constructed line of brattice will only provide fair ventilation for a distance of 100 ft. Beyond this point the volume or air reaching the face falls off rapidly.Some of the shortcomings associated' with the use of brattice cloths are:1. Hurried installation, necessitated by a rapid advance, often results in poor workmanship with, consequently, an excessively high leakage rate.2. High places caused by falls of roof are difficult and time-consuming to seal.3. Curtains, in lines of brattice crossing transport routes, are difficult to maintain.4. Lines of brattice interfere with rock-dusting and clean-up of fine coal.5. Repair and maintenance of brattice consumes much...

Jan 1, 1959

By Matthew Violot

Vale Canada?s Birchtree Mine, located in Thompson Manitoba, has been experiencing problems with hanging wall / footwall dilution, as well as sloughing off of adjacent stopes and temporary stope block backs. Birchtree Mine is interested in determining how time affects the stability of their open stope blocks. Many factors simultaneously influence open stope stability (rock mass quality, joint condition, stress condition). This makes it challenging to determine the influence of a single parameter such as exposure time or stand-up time. This study focuses on determining the effect of exposure time on open stope dilution and combines stress analysis and empirical based approaches.

Jun 1, 2012

By Keith A. Heasley, Lee W. Saperstein

This paper investigates the use of backfill zones and yielding pillars for subsidence control. The investigation begins by choosing an appropriate subsidence predictive technique to simulate the proposed subsidence-control schemes. Two case studies are performed in order to delineate the accuracy and utlility of the chosen predictive technique and then the results of these case studies are used to establish appropriate sets of regional site parameters. Next, a detailed analysis of the major variables affecting the outcome of the subsidence-control simulations is conducted and graphical displays of the exact sensitivity of the surface subsidence to these variables are given. Finally, alterations to the surface subsidence that are expected from using two major subsidence-control techniques are presented. The first technique to be assessed is a backfilled pillar centered longitudinally in a panel. With this arrangement, a minimal amount of backfill material can produce substantial decreases in vertical displacements. The second technique to be assessed is the use of yielding gate pillars to reduce the sinuosity of the transverse subsidence over adjacent panels. With proper design, this technique can greatly curtail surface strains and help minimize remedial drainage control.

Jan 1, 1986

Pyrrhotite is pyrophoric when in a finely divided form. The problems of disposing of large quantities of finely divided pyrrhotite separated out by metallurgical processing from ore are formidable. In the case of an underground mine, a solution to the problem of disposal is to place the pyrrhotite in the stoped out areas and seal from any air supply. Further, the pyrrhotite could be diluted with tailings which would reduce the possibility of combust- ion. Several enquiries to various centres and authorities have shown that the products of the slow oxidation of pyrrhotite with moisture present can cement an inert matrix into a stable fill similar in physical prop- erties to fill stabilised with Portland cement. Stabilised fill can be used to advan tage with a suitable mining method to provide high recovery. The investigation demonstrated that air and 15% w/w water must be present for the fill to harden and that the sizing of the particles is a critical factor in drainage of a hydraul- ically placed fill and subsequent even harden- ing of the fill in a stope. With the materials used in the experiments in which the - 51 micron component of the tailings had been dis- carded, an optimum mix was found to contain 4:1 tailings/slag ratio and an overall pyrr hotite concentration of 8% (all proportion by weight). Approximately 34 days after drain- age to 15% moisture in natural air flow condit- ions, an unconfined compressive strength of 1.862 MPa was attained. A subsequent experi- ment was conducted with a sample of optimum mix in a pipe one metre long in forced air flow conditions. At a superficial velocity of 3.Om per hour the mix required 155 hours to harden to 1.862 MPa after drainage to 15% w/w moisture content. The pressure drop bet- ween the top and bottom of the mix in the pipe remained constant at 9 KPa/metre length. This result suggests that forced air flow conditions will increase the rate of hardening. No dangerous effluents were detected in the course of the experiments which could affect mine equipment or personnel.

Jan 1, 1973

By J. L. Vanderbeek

Investigations have been conducted at Chino Mines Company into the effect that SAG mill recycle material (critical size) exerts on SAG mill throughput and specific energy requirements. Tests were conducted on the laboratory, pilot, and plant scales, to evaluate the merits of alternative treatment options. Removing critical size material from the SAG mill circuit has been shown to improve new feed rates by 34% with a reduction in specific energy (kWh/ton) of 33%. Test results obtained to date are presented.

Jan 1, 1985

By G MacDonald, B Forsyth, D Corkery, T

An investigation was carried out at Diavik Diamond Mines Inc (DDMI) to identify and quantify the mechanisms through which ammonium nitrate (AN) was entering the mine discharge water. The goal was to develop and complete an investigation of the potential AN loss mechanisms in order to assess their contribution to ammonia in the mine water system. The initial phase of the project involved the collection and analysis of blasting and water quality data that were used to determine the mechanisms by which the ammonia enters the mine water system and to establish a baseline data set for comparison with results from future trials designed to reduce AN loss. Three potential options for reducing AN loss were identified through the first phase of the project. The second phase of the project involved conducting a series of monitored trials with changes made to the drilling and blasting process. The results of these trials were compared to the baseline data set to determine if the changes introduced for the trials had reduced AN losses while producing satisfactory blast results. This paper describes the process for the collection of the baseline data, provides an analysis of the resulting data, discusses the changes made to blasting operations in order to minimise AN loss and describes the results observed subsequent to these changes.

Jan 1, 2007

By J. J. Kim

In a study of buildup in a green-feed reverberatory furnace, it was determined that approximately half of the crucible area has a moderate buildup of 25 in. or less, and that the area extending 45 f t from the burner end of the furnace has only a slight buildup. The false bottom, averaging 6 in. in thickness, was found to cover the entire crucible area. The stratification of Cr2O3, A12O3, and SiO2 occurs throughout the slag layer; this phenomenon is the principal reason for the formation of the false bottom in the green-feed reverberatory furnace. The false bottom is caused primarily by the settling of FeO*(A1,Cr),03 aggregates, which are derived mainly from returned converter slag. The false bottom can be transformed to a solid permanent buildup in the furnace, particularly when the matte is completely withdrawn. From the material balance of Al2O3 and Cr2O3 around the furnace, It is estimated that the average rate of aluminum chromite accumulation is approximately 0.3 ton per day or less.

Jan 1, 1976

By R. C. Kellner

Duval Sierrita Corporation, a wholly-owned subsidiary of Duval Corporation, operates an 86,000 STPD copper-molybdenum concentrator near Tucson, Arizona. Shortly after production commenced in February, 1970, it became apparent that the reduction crushing system represented a limitation to reaching the design capacity of 72,000 STPD. The development work performed on the reduction crushers in order to first meet design capacity, and to subsequently increase production to 86,000 STPD is described in this paper. The Sierrita plant is a conventional three stage crushing sys- tem. All crushers were supplied by the Allis-Chalmers Corporation and consist of two 58 x 89 Superior gyratories, four 138b EHD hydrocones, and ten 384 hydrocones. Screening is performed prior to and subsequent to secondary crushing and in closed circuit with the tertiary crushers. Typical throughput rates and equipment sizes are presented in Figure No. 1.

Jan 1, 1975

By D Laskovski, T Nguyen

Flotation surveying can be an extremely powerful means of determining opportunities for circuit optimisation and benchmarking. The type of survey employed depends heavily on the nature of the information required from the survey. It follows then that the type of survey determines the type of samples required; however, regardless of the type, the success or failure of a survey is often dependent on the correct used of appropriate sampling techniques at each sampling point. For a successful flotation plant survey it is vital that the correct samples be collected at the correct time in respect to the feed and each other. This paper discusses the current best practice sampling methods used in flotation surveying and discusses in detail the ideal sample masses based on theoretical analysis. Comparisons with JKTech’s database of real plant operations will then be made.CITATION:Laskovski, D and Nguyen, T, 2014. An investigation of current flotation survey sampling, in Proceedings Sampling 2014 , pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014