Search Documents

By Mohammadreza Khanmohammadi, Kazem Fakharian

"AbstractIn driven piles, the gradual dissipation of excess pore water pressure and consequently the soil setup significantly contribute to increasing the pile capacity with time. The question is risen that how the scale differences affect the stress state variations around the pile shaft and at the pile tip? Would the CPT predictions better correlate with End-Of-Drive (EOD) or Beginning of Restrike (BOR) conditions? On the other hand, are the proposed a and ß parameters for clayey soils mostly predicting the EOD or BOR situation? The main objective of this paper is to back calculate the a and ß parameters from CPT profiles, pile Dynamic Load Tests (DLT) at the EOD and BOR as well as Static Load Tests (SLT) and evaluate how they compare with those suggested in literature. Four precast 400 mm square concrete piles driven in North Azadegan Oilfield in Khuzestan Province were selected for the comparisons. CPT test results were available from the extensive geotechnical investigation at the study site. DLT tests using PDA were carried out at EOD, 1 day and 14-day BOR on all the 4 piles. All the piles were SLT tested as well. The UniCone software was used to estimate the tip and shaft resistances using 4 methods including the Dutch, Eslami & Fellenius, LCPC and Schmertmann. The results indicate that the a-method based on the proposed values in literature has predicted a shaft capacity of 90% of the 14-day BOR. This is while the ß-method has predicted a shaft capacity equivalent to 1-day BOR results only. Therefore, both methods have under-predicted the shaft capacities compared to real capacities measured after the significant soil setup in the study area. Two of the CPT methods have underestimated, one has overestimated and one has matched the estimated 60-day capacity."

Jan 1, 2014

ONE of the phases of mining wide ore-bodies, such as are found in Broken Hill, is the laying-out and design of the sill floor gangway timber, When, in the above operation, a detail has to be repeated frequently, it is desirable in the interests of efficiency that that detail should be standardized as far as possible. Before arriving at a standard design e.g., a crosscut layout-it would seem necessary to compare its strength with some other unit of timber and see that the general design is at least as strong as the unit that has been taken for comparative purposes, In these notes no attempt is made to calculate the stresses to which timber underground is subjected, but merely to draw a comparison between the relative strengths of the various cross sections of timber in common use underground.It has been assumed for the purposes of comparison that the milling exerts pressure in a vertical plane only, and is uniformly distributed over any area. A beam supported at both ends, and with a uniformly distributed load, has the maximum bending moment at a point midway between the points of support, and equals- WL2 8 where W = load per unit length. L = distance between points of support.The bending moment also equals M-, where y M = modulus of rupture of the material in question. I = moment of inertia of the section of the beam about a given axis.Y = distance of extreme fibre from that axis. WL2. I The formula -8- = MY- only holds good until the elastic limit...

Jan 1, 1923

By H. P. Stüwe

HE recent papers of Aust and Rutter112 have again brought to mind the importance of certain "special" orientation relationships between the lattices of two fcc crystals on the mobility of the grain boundary separating them. No theoretical treatment of this problem has been offered till now. The only principle published so far that has given an indication why certain orientation relationships should be "special" is the counting of "coincidence sites" according to the suggestions by Kronberg and Wilson.3 The "coincidence plots" published by these authors show, for instance, that two fcc lattices rotated by 38 deg around a common (111)-axis have 1/7 of their lattice sites in common. Such an orientation relationship is also characteristic for high boundary mobility. The accuracy of the orientation relationship needed for high mobility is not too rigid. Deviations up to 10 deg from the ideal orientation seem to be tolerable as can be gathered from the experimental data.'j4 The auestion arises, then. how the density of coincidence sites will be affected by a deviatioi from mathematical accuracy. This can be checked by a simple model. Two sieves are prepared, the arrangement of the holes corresponding to lattice sites on a (111)-plane in a fcc crystal. They are placed upon each other, Fig. 1. One is kept fixed, the other is rotated around an axis pushed through one hole in common to both. The light falling through holes of both sieves is then a measure for the density of coincidence sites. If the diameter of the holes is very small, light intensity is contributed only by holes the centers of which coincide "exactly." If the diameter of the holes is rather large, some intensity will be contributed by

Jan 1, 1962

By T. J. Snell

Bolnore Village in Haywards Heath, Sussex, England, is a large development covering 8 to 10 hectares and expected to provide 1500 homes in five phases to assist in the continuing demand for new homes in the London area. Part of the development required housing on a relatively shallow slope found to have deep seated failure planes which are fairly prevalent in this part of Sussex. Locally the slope angle was around 20 degrees but more typically the gradient was 6 to 7 degrees. There were significant concerns about slope stability and bearing capacity due to pre-existing shear surfaces and the complex geotechnical profile. There was some evidence of instability in the form of residual shear surfaces and tension cracks. The development required terracing the site with retaining structures up to 5 meters in height, formation of access roads and foundations of new houses. The developer Crest Nicholson adopted a collaborative approach with consulting engineers Powell Tolner and specialist geotechnical contractor Keller Ground Engineering. The solution consisted of a novel combination of contiguous bored piling, ground anchors, and both block work and timbacrib retaining walls to ensure the geotechnical issues were adequately addressed within the time and cost constraints set by the team. The paper describes the geotechnics of the problem together with the design, practical implementation, and site progress achieved

Jan 1, 2006

The Department of Mineral Resources has a statutory responsibility for mine site environmental management and control in New South Wales. The Department is focusing on an environmental management systems (EMS) approach, as a management tool to achieve æbest practiceÆ outcomes both within our own organisation and on mine sites. One of the DepartmentÆs tools is environmental risk assessment and management which incorporates the Mining, Rehabilitation and Environmental Management Process (MREMP). The MREMP was introduced many years ago in order to integrate the activities of key stakeholders who may have a material interest in the mine. The MREMP provides an ideal mechanism by which ædue diligenceÆ requirements and environmental management programs can be integrated into mining operations and lead to a sustainable post-mining land use.

Jan 1, 2002

By J. Koster

[In lQ jG thc E'lcct,ro:~(: L7.l :~u..-ic:ll S;%cti ?n of t?c :I. tcIl~tr,-;lcal 3:vi cioa, ?U~CE~U of lv!irtos, bc,~m an 9.ct iv.t In-:?*t ik7;5i GI of r.:ct.l-;c?;is for rccovcrin,; niclrel, cop?ir, an2 ?? cciou:; ~ot-1 c 1;-on or; :; of tile 3unl~crvi~.l~~ tiistrict in C1ni.k Coult:r, !Icl.r. ]

Jan 1, 1939

By J. Koster

[In 1178 thn S-00n of thr !~Viluralcal Divicion, pur--'11 cf Mines, bcran an o. 't iv in': n-t!Y_Vnn of vothod; for recoverin'-1, Achol, copp~r, nK precioun notnin Zycn o;. -z of tic Bunkcrvillo KOH& in Clark County, Tcv. Tho Bunkcrvillo ran arc of t,-j)(,e of -iincrilization similar to that of 02 SWbury, Ontario, CannO, nichvl dc-?o?-:.t,. At prcoont, only n anall tonnes? p of ore has loan cxDr)scd in t*ic' :hui:er7ilIp rc: inn, ann. there is decided nce! for orjn: izod OrospectiAg ina drvclo-nnnt "crk there. It wann believod, howevar, t4it the dc,cuits varo 3ilficUntly siSnIficant to warrant an investigation iito their]

Jan 1, 1939

By Muhannad T. Suleiman

Temperatures below freezing significantly enhance the soil shear strength and stiffness and to a lesser extent increase the compressive strength of concrete as well as the yield and ultimate strength of reinforcing steel. Consequently, the lateral load resistance of bridge columns supported by drilled shafts becomes dependent on seasonal weather conditions. To investigate the effects of seasonal freezing on the behavior of bridge columns supported by drilled shafts, large-scale field lateral load tests were conducted at 23°C (73.4°F) and -10°C (14°F) on two identical units at an field test site, which consisted of glacial till soil classified as low plastic clay. The bridge column-drilled shaft systems were subjected to cyclic lateral load with the maximum lateral column top displacements reaching approximately ±30 cm (±11.8 in.). The soil at the test site was characterized at different temperatures using unconfined compression tests in the laboratory as well as in-situ Cone Penetration and Pressuremeter Tests. Using these test results, the lateral load behavior of the column-drilled shaft systems were analyzed utilizing numerical models that consisted of beam elements representing the concrete column and the shaft and lateral springs representing nonlinear p-y response of soil. This paper focuses on comparing the calculated responses of test units with different p-y curves that were developed for the soil near the ground surface using the laboratory and in-situ tests. From the experimental study, the response of the unit tested at -10°C (14°F) was found to show 44% increase in lateral force resistance and 0.84 m (2.76 ft) upward shift of the maximum moment location compared to the response of the identical unit tested at 23°C (73.4°F). Theoretical behavior that included the temperature effects on soil, concrete and steel properties provided good correlation with the measured responses when the soil near the ground surface was modeled using the unconfined compression test or the Cone Penetration Test data, but not the Pressuremeter test data.

Jan 1, 2006

By Lewis Robert M.

The importance of phosphate in feeding the people of the world has been recognized by mining companies as they continue their search for new ore deposits and ways of improving phosphate production. An extensive phosphate-recovery research project involving investigation of beneficiation variables by batch testing, flotation pilot-plant processing of the major portion of the ore, gravity separation of the coarse fraction, and recovery of byproduct heavy minerals of a North Carolina phosphate deposit has been completed. Data obtained through batch tests enabled the development of an economical flowsheet which proved successful for the efficient recovery of a good quality phosphate concentrate in a pilot plant.

Jan 1, 1975

By Alok Garg, Rajeev Kumar Dayal

The Himalayan ranges have complex geological formation induced with locked up tectonic stresses and squeezing ground conditions. High overburden, steep slopes, perennial snow, and forest cover restricts accurate prediction of geological features, resulting in surprises during excavation. The tunnel planning under high altitude, extreme climatic, and unfavorable approachability conditions requires elaborate detailing. The construction technique and working faces for excavation are influenced by site accessibility/high overburden conditions, restricting the provision of access tunnel or shaft. The paper discusses site constraints influencing construction method and working faces for 8.9 km long highway tunnel at elevation 3,000 m under 1,900 mover burden through quartz-mica-schist formation.

Jan 1, 2001

By Deepak Vidyarthi

This paper deals with the significance of Explosive Energy in the optimization of blast design parameters, and the benefits emerging out of it. It is based on the original work done by the author in developing and successfully implementing a site-specific software package on ‘Blast Design Optimization’ at Kudremukh Iron Ore Mine in India with a production level of 22.5 million tonnes of crude ore and off-take of Explosives of approximately 5500 tonnes per annum. The software package has yielded tangible results in effecting reduction in Explosive Consumption, substantial savings in the Cost of Explosive, besides Environmental Improvements by way of attenuation of Blast Induced Ground Vibrations as well as Air-Blasts. By carrying out regular ‘Regression Analysis’, and determination of the Rock Constants, it has been possible to further develop software packages as well as prediction curves for prediction of Peak Particle Velocity, Safe Charge of Explosive, Air-Blasts etc. A model has also been developed for the prediction of ‘Fly Rock’ although at KIOCL, fly rock does not pose any problem.

Jan 1, 2006

By R. Sweennen, A. Vervoort, J. Caers

A case study is presented of the mechanical behaviour of fractures in the Westphalian A and B siliciclastic succession of mud-, silt- and sandstones with intercalating coal layers in the Campine basin of northeast Belgium. Mining ceased in the area in 1992 and a pilot well was drilled to assess the feasibility of methane extraction by hydraulic fracturing. Work was carried out to study the influence of types of cement fill in fractures on the shear behaviour of the rocks by comparison with that of the coal seams. X-ray computerised tomography was used for visual appraisal and selection of jointed rocks before destructive shear testing was carried out. Two major type of veins were found to be present, one cemented with carbonate and the other with kaolinite or kaolinite/carbonate. Uniaxial compressive strength and shear tests showed that differentiation of the two types of veins was vital in evaluating the strength of the sandstones, as cementing of the fractures by rigid carbonate minerals can reinstate the strength of the rock masses to that of the intact material. Kaolinite was more susceptible to plastic deformation than carbonates

Jun 19, 1905

By Dean Bray

During the past three years, a new rear-dumping dragline bucket technology has been patented, developed and tested at North Dakota coal mines. Field testing has shown that this new concept in dragline bucket technology can improve strip-mining efficiencies by reducing cycletimes and increasing dumping radius. This article details the process, participants and the results for the development of a rear-dumping dragline bucket. Participants in the process In November 1995, the board of directors of Dakota Coal authorized the execution of a field test and option agreement and a license agreement with the partnership of D.F. Schmidt, electrical/maintenance supervisor, and Bill Lengenfelder, president of Modern Industrial. The board also authorized entering into a dragline bucket field-testing agreement with the Falkirk Mining Co.

Jan 1, 1999

By S. C. Sun

A study(1) on the sulfuric acid extraction of alumina from some Pennsylvania ferruginous clays indicated that the published electrolytic method(2)(3) seems to be more efficient than the known chemical methods (4-9) for removing iron from the leach liquor. The main disadvantages of the chemical methods are the consumption of excessive amounts of reagents and/or the precipitation of prohibitive amounts of aluminum. In the electrolytic method, iron is deposited on the mercury cathode, while aluminum is not and remains in solution. This method, however, had been handicapped by the lack of an effective and economical way to purify the contaminated mercury cathode.(7)(l0). Described herein is a scheme for cleaning the mercury cathode, and for recycling the clean mercury back into the electrolytic cell. Armed with such an apparatus, the effects of applied potential, temperature, and operation time on the electrolytic separation of iron from aluminum sulfate solutions were determined. For the sake of comparing results, a term, removability, was coined to represent the percentage of iron amalgamated per unit height of electrolyte (cm.), per unit surface area of cathode (cm.2), per unit of operation time (second).

Jan 1, 1968

By N. Abdel-Khalek, A. Youssef

The tailings from beneficiation of Florida phosphate ore contain considerable phosphate values. These tailings are currently discharged into large disposal areas. More than three million tons of P2O5 are discarded with the phosphatic slimes (clays) in Florida each year. These phosphatic clays not only create one of the most difficult disposal problems in the mining industry, but also represent a tremendous loss of P2O5. As the quality and quantity of Florida’s phosphate reserves diminish, recovery of phosphate values from these wastes becomes more vital. This will also significantly lengthen the life of these important phosphate resources. Thus, it is the goal of this study is to recover more than 80% of the phosphate values in phosphatic clays. A systematic study to characterize samples taken from inactive disposal area has been conducted. The data suggest that natural segregation takes place in the settling pond. In other words, coarser particles settle closer to the feeding point of the pond. Flotation tests were conducted using the +325 mesh fraction of samples obtained from sites close to the feeding point (sample# A) and further from that point (sample# B) and (sample# C) which is even further away from the feeding point. The results show the following: Sample# A gives the highest grade and recovery, followed by that of # B and then of # C. There is a great potential to upgrade sample# A where concentrates of high grade (68.9-70.1 % BPL or 31.5- 32.1% P2O5) and recovery (~86.6-95.4 %) can be obtained under the investigated operating conditions (1.0 – 2.0 kg/ton sodium silicate and 1.5—3.0 kg/ton collector mixture of fatty acid and fuel oil). The mineralogical and chemical analysis of all samples is presented in this paper for comparison. Only in this paper, the flotation data of (site # A) are discussed below.

Jan 1, 2002

By M. England

Test equipment has been developed to record automatically both the displacement of the pile head and the load applied during a conventional maintained load pile test. Some systems also have, in addition, been fitted with the facility for maintaining the applied load, as set by the operator, at very constant levels. The advantages are both commercial and technical, but a well trained operator has to be in attendance to control the test. Since typical test specifications in the UK require more than 19 hours to complete, it became inevitable that at least one equipment operator remained on site to expedite the test for its duration. Although electronic measurement and data logging of load tests may be more safe than previous direct observation of dial gauges. A single person remaining on a construction site alone is not to be recommended, even if they are just supervising the test. Further development of the testing system produced equipment which will perform the entire test specification as required without operator intervention. To achieve this, full automation is employed. The patented method particularly addresses the safety requirements and by using additional sensors, detects any uncharacteristic behaviour of the pile under test or of the reaction system and the equipment takes appropriate action in a controlled and safe manner. The quality of test data returned from these automated systems is a key element when analysing pile behaviour with models such as CEMSOLVE? and TIMESETTM. These analysis methods often indicate ground disturbance resulting from installation technique and have allowed pile design to be optimised using actual field data rather than theoretical considerations alone. An additional feature is remote access, this allows the data recorded to be transferred and the progress of the test to be viewed from practically any location. This permits experts to view the data 'live' and allows rapid diagnosis of any problems with the expected pile behaviour.

Jan 1, 2002

By A. D. Davis

The Gilt Edge Superfund Site is a former heap-leach gold mine that currently is being remediated in the Black Hills of South Dakota. Mine runoff water is treated before release from the site. The field pH, before treatment, is about 3, and the water contains arsenic and some heavy metals, in addition to sulfate concentrations of about 1400 to 1500 mg/L. In the Keystone area of the Black Hills, naturally occurring arsenic has been detected in ground-water samples from wells. Keystone City Well #4, which is not used currently, showed arsenic concentrations of 36 parts per billion (ppb) and sulfate concentrations of about 19 mg/L. With field samples of water from these sites, a limestone-based method was successful in reducing arsenic and heavy metals concentrations. The results are significant because previous research with the limestone-based method mainly had involved samples prepared with distilled water in the laboratory, in which interference of other ions such as sulfate did not occur. The research indicates the potential for broader field applications of the limestone-based removal method.

Jan 1, 2011

By Ke Yang

Drilled shafts are widely adopted as the foundation for sound walls. However, there has been a lack of uniformity in design and analysis methods and design criteria, in terms of factor of safety against ultimate capacity failure as well as the allowable deflection. In order to establish a uniform design methodology for the drilled shafts supporting sound walls in cohesive and cohesionless soils, respectively, a database of full-scale lateral load tests on fully instrumented drilled shafts was collected. Based on the compiled database, existing design methods and design criteria of laterally loaded drilled shafts were evaluated. Broms method and COM624P (or LPILE) are suggested as the design methods for drilled shafts supporting sound walls in both cohesive and cohesionless soils. Additionally, the corresponding design criteria, including factor of safety and permissible deflection, for both design methods are recommended. Two full-scale lateral load tests on fully instrumented drilled shafts were subsequently conducted in Colorado to further verify the design recommendation. A comprehensive geotechnical investigation program was also carried out at the two new lateral load test sites that included pressuremeter test, SPT, as well as laboratory triaxial consolidated undrained tests and direct shear tests on the soil samples taken from the lateral load test sites. The test results obtained at these two load test sites were employed to validate the recommended geotechnical design and geotechnical testing methods for the drilled shafts supporting sound walls.

Jan 1, 2007

By Dominique Vié

Standards methods covers the procedures for testing deep foundation to determine the force and velocity response to an impact of a pile driving hammer or similar device. The results of analysis generally include an assessment of pile integrity and the value of maximum dynamic stresses. But evaluation of static bearing capacity remains a matter of individual engineering judgment. A new 1D finite elements model has been developed for dynamic stresses and velocity analysis. Following an international benchmark of bearing capacity prediction organised by the Belgium Building Research Institute (BBRI), 12 piles in a site of fissured stiff tertiary clay tested in 1999, and 12 piles in a site of dense sand tested in 2001, comparison are proposed between analysis of dynamic tests and static tests results. A procedure is proposed to take in account the results of dynamic test for evaluation of bearing capacity.

Jan 1, 2002

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991