Search Documents

By Eugene H. Skinner

The 7-mile Flathead Tunnel, located in the central Salish Mountains of northwestern Montana, was constructed between 1966 and 1969, With the contract awarded April 19, 1966, drill and blast tunnel excavation began September 30, 1966, and was completed June 21, 1968, in 488 tunnel-driving days, Peak advance was 66 feet per day. On June 27, 1969, all tunnel concrete lining was completed. Average wall and arch concrete placing rates exceeded 1,700 cubic yards daily, with nearly half of the concrete placed during a severe winter season. Major cost savings in concrete tunnel lining were achieved through a value engineering clause in the contract. Achieving consistent results and high rates of placement in concrete lining ranked equal to ground control in overall tunnel problems. Ground control problems exceeded expectations and were of continual concern throughout excavation, One support collapse in the tunnel and one portal slide condition developed during construction. Critical surface geologic exposures were largely obscured; only a portion could be accurately projected underground, An instrumentation program to gather basic data on rock defamation near the heading face for support purposes was a pioneering effort. The Flathead Tunnel was placed in service on November 7, 1970.

Jan 1, 1974

By D M. Frantois-Bongarton

"A few situations are first reviewed where practical shortcuts lead to acceptable solutions where none seemed to be possible. These include: The solving of many complex sampling optimisation problems with the simple approach of the worst case policy (WCP). A simple approach to single-stage sampling problems will be mentioned at continuation. In the plants, minimising the impact of border effects in incorrect samplers, so that the resulting samples are approximately correct and acceptable in practice because the bias risk attached to them is controlled. Examples are given, as well as practical tools and a general methodology.Finally, some sources of undue conservatism are reviewed with general recommendations aiming at eliminating them.CITATION:Frantois-Bongarton, D M, 2012. Practical considerations and shortcuts in sampling, in Proceedings Sampling 2012, pp 171-174 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 21, 2012

The purpose of this study is to formulate practical guidelines for active underground mining in close proximity to water bodies. This was accomplished through systematic completion of three phases of study: I) Collection and Documentation of Data; II) Application of Existing Guidelines to Case Histories of Previous Inundations; and III) Development of Recommended Guidelines for Underground Coal Mining Near Bodies of Water. Phase I of the study involved a worldwide data collection effort designed to obtain foreign and domestic guidelines for mining near water bodies, and accident records and case histories of accidental mine inundations. Within Phase II, existing guidelines were categorized and classified and then evaluated as to their effectiveness in precluding past inundations had they been in effect at the time of inrush. Advantages and disadvantages of existing guidelines were defined. Drawing on the broad data base established in previous study efforts, Phase III was directed at development of viable guidelines to promote the greatest possible coal extraction while precluding accidental mine inundation. Two levels of guidelines are presented; Level I Guidelines require little or no subsurface exploration on the part of the mine operator, while Level II Guidelines recommend various testing and investigative procedures to permit greatest possible mineral extraction. This report presents findings and conclusions of the study.

Jan 1, 1976

Sufficient time has elapsed since the enactment of the amendments to the mining legislation in 1981 to enable an examination to be made of the way in which the licensing system operates in practice. One of the most important decisions in resource management in New Zealand is whether or not rights of access to the resource should be conferred by the Crown upon an appropriate private sector participant. The licensing system is the means for allocating these rights of access. The manner in which the licensing system is administered, therefore, is crucial to natural resource management in New Zealand. What is the mining licensing system in New Zealand designed to achieve? This simple question admits of no easy answer. Is it the identification and development of the mineral resources of New Zealand? Are these objectives tempered by issues of resource conservation and environmental protection? Is a balance to be achieved among these competing factors? Does the legislation contain any priorities? Does the system respond in an ad hoc manner to particular facts and circumstances or does it operate within a more predictable framework? To what extent are decisions made on access to minerals with reference to the development or conservation of other resources? These questions may be summarised in the title to this paper which poses the question whether mining licences are instruments for resource management.

Jan 1, 1988

By J. H. Bain, D. C. Haigh, L. C. Parsons

Jan 1, 1964

By H. C., Simpson

MANY metals by virtue of their place of occurrence as ore, and their uses are travelers! Iron and steel, for instance, is one of the greatest of travelers in the form of ships and the romance of iron in this respect is only just beginning to be superseded by the stories which can be told of the travels of aluminum and its alloys, used in the building of airplanes. Tin is a traveler from the Straits Settlements to this country and Europe, for use in the canning industry; afterward traveling all over the civilized world as a part of the container for preserved foods. Silver is somewhat of an aristocrat, when its uses are measured against those of the baser metals. From earliest times it has been used for adornment (first perhaps o4 the person and later for the embellishment of weapons and' buildings), for the making of fine ar¬ticles used in the household, and as money. While its uses have been widened by the discoveries in chemistry, electricity and other sciences, its early uses are still much in evidence in our modern life.

Jan 1, 1928

By G. M. Schwartz

THERE has been considerable controversy regarding the structure and mineral constituents produced when iron ore is sintered. This investigation was undertaken in order to establish the fundamental reactions that take place in the sintering process by determining the nature of the resulting minerals. The writer's immediate interest in the subject arose mainly from the request of E. W. Davis for information based on a microscopic study of sinter submitted by him in May, 1926. In the author's preliminary work, samples of iron-ore sinter were secured from the Minnesota School of Mines Experiment Station and from commercial plants. These were polished by the usual methods for polishing opaque ores. In order to study these surfaces satisfactorily, it is necessary to magnify them rather highly, a range from 100 to 1000 dia. being used. For the higher magnifications oil-immersion lenses and an intense source of light are necessary. After the preliminary study had shown the problems involved, a series of small samples were sintered under carefully controlled conditions and with analyzed materials. Variations in the relative amounts of ore, coal and water were made in order to study the effect of each constituent. The attempt has been to arrive at a clearer understanding of the sintering process and the reactions involved without reference to any preconceived notion as to sinter. It is clear that the study of polished surfaces has yielded results not possible with thin sections alone. The thin sections made in this work were found unsatisfactory at magnification greater than 75, whereas magnifications of 1000 were easily studied with reflected light on carefully polished surfaces. A rather complete statement of observed facts is made so that the reader may form his own conclusions. The writer's interpretations are suggested.

Jan 1, 1929

By Gerald G. Johnson

The use of the Scanning Electron Microscope to characterize Coal Mine Dust has been possible because of two circumstances. First, the imaging process of the SEM allows multiple signals (secondary electrons, back scattered electrons, x-ray emission, etc.) to be viewed. Second, the use of a computer to analyze the signals and perform statistical tests on the results. The parameters described are size, shape, chemical composition, mass distributions, and particle thickness. Although the system is intended for particular systems, those of agglomerates (whether tile same or not) are handled by special aspects of the computer programs. The work on fibers is not completed at the time of this report. This work discusses the hardware (developed especially for this process) and software (both on an IBM 360/370 and a PDP 11/20). The latter system allows direct interaction between the operator of the SEM and computer for maximum information at the least time.

Jan 1, 1979

By J. A. Burkhardt

Field measurements and theoretical studies have been made of pressure surges—momentary variations in fluid pressure—produced by movement of pipe in mud-filled boreholes. Pressure measurements were recorded by five pressure gauges located at various positions in the borehole. An important positive pressure peak was found to occur as the casing moved with maximum velocity. Important negative peaks were found as the casing was lifted from the slips and as brakes were applied to stop pipe movement. A rigorously formulated theory has successfully predicted the sequence and magnitudes of these positive and negative surges and has established a basis for understanding how they occur. Both the measurements and theory indicate that the most important pressure surge is usually due to viscous drag of the flowing mud. The theory of viscous-drag pressure surges has been approximated by simplified graphs and calculation procedures to facilitate ready use in field operations. Comparison of measured results with those predicted by the simplified theory shows that the magnitude of this surge can be predicted accurately. INTRODUCTION It is widely recognized that raising or lowering pipe in a fluid-filled borehole produces momentary variations in fluid pressure, commonly called pressure surges. Both negative (or "swabbing") surges and positive (or "fracturing") surges may occur. In 1934, Cannon1 measured the negative surges and showed that they could be large enough to cause flow of formation fluids into the well-bore and, in extreme cases, lead to blowout conditions. Later, Coins2 measured the positive surges associated with lowering pipe. His results and subsequent field operations strikingly demonstrated that pressure surges could be an important factor in some cases of lost returns. In addition, although the evidence is less clear than in the case of blowouts and lost returns, other investigators 3, 4 feel that pressure surges probably play a part in many instances of minor gas cutting, salt-water flow and other hole trouble. The importance of pressure surges in drilling operations led naturally to attempts to explain the physical causes, nature and magnitude of the surges. Cardwell5 was the first to publish a theory which allowed the quantitative prediction of momentary pressure variations. He assumed that the drilling fluid was a 300-cp Newtonian fluid in turbulent flow. Most field muds have a considerably lower viscosity and are generally believed to be Bingham plastic in nature.6 However, card-well's results were useful because they were presented in a form convenient for field use and, in some cases, gave a reasonably accurate predicted value for the maximum pressure surge. Subsequently, Ormsby7 published a more comprehensive theory of pressure surges. He discussed both laminar and turbulent flow and considered the theory of mud-bypass devices for reducing pressure surges. As a consequence of his more rigorous approach, his results were more accurate but more complex and difficult to use. Further, both Ormsby and Cardwell considered only the pressure surge arising from viscous drag of the moving mud. Clark later published idealized graphs of surges and presented equations for predicting their magnitudes. In addition to pressure variations arising from viscous drag, he considered those caused by inertial effects. His theory was in this respect more complete than those of Cardwell and Ormsby, although he did not discuss pressures due to breaking of the gel. Furthermore, his equations, while not exceptionally complicated, were too complex for ready use at a drilling location. One difficulty common to all three theories is that none was tested rigorously by direct comparison with measured pressure surges. Their accuracy, therefore, could, not be demonstrated. Further, the two theories based on most realistic assumptions (Ormsby and Clark) required the solution of one or more rather complex algebraic equations. The research described in this paper was undertaken to supplement that described and to overcome some of the difficulties noted. It seemed obvious that a fully satisfactory study of pressure surges should encompass three main phases. 1. A valid theory useful in all field situations must be developed. This theory must be based upon realistic assumptions, must be formulated rigorously and should lead to clear concepts whereby the nature of pressure surges can be easily understood. 2. The theory, however complex and involved, ultimately must be presented in simplified form for convenient field use. This may involve extensive machine computations and the use of figures and empirical equations. 3. The accuracy of the simplified equations must be established by comparing measured pressure surges with those predicted by the theory. These must agree both in their characteristic nature and in magnitude. 'This means that careful measurements of surges occurring in actual field operations must be made.

What is the preferred electrolytic cell design and why? Hall: Considerable research remains to be done on electrolytic cell design. Studies are presently being conducted to determine optimum voltage and amperage. Zadra cells, which were used in some of the first carbon plants, are efficient when properly installed. Gold and silver are deposited on large-capacity, cylindrical steel wool cathodes. At times high value sludge falls from the cathode to the bottom of the cell. Rectangular cells, which were developed at some smaller operations in Nevada, require less floor space and have some desirable features in that cathodes can be moved and sludge can be removed from cell bottoms without actually shutting down the circuit. In South Africa two types of cells using graphite and diaphragm configurations are being tested. Duncan: The rectangular cell has one problem it's easy for shortcircuiting to occur. If you don't have a good seal on the side of the tank and on the bottom, the solution is going to want to flow around the bottom and sides of the cathodes and you're going to get poor performance in the cell. That is the advantage the Zadra cell has over the rectangular cell. With good sealing, which is a must, you should be able to get a ratio of the value of the solution going in to the value of the solution coming out of 10 to 1. Ken, can you tell me what you're attaining on the Zadra? Hall: At the Homestake gold operation in Lead, the cathode in the No. 1 electrowinning cell is loaded to about 600 ounces when it is moved to the refinery. At this time the No. 2 cathode is moved to the No. 1 cell. The No. 3 cathode is moved to the No. 2 cell and a cathode with new steel wool is placed in the No. 3 cell. In rectangular cells this sometimes is not possible because the loading on the cathode in the last cell may be as high as that in the No. 1 cell. As Don has pointed out this can probably be prevented by good seal design between cathodes. Potter: At the risk of sounding as though I'm straddling the fence, I really believe that either the round cell, as developed by Jack Zadra, or the rectangular cell will do an acceptable job. The Zadra is a fine unit. Leaks are not unknown but there are not very many. However, the rectangular cell is very saving of floor space. Plastics have been greatly improved during the past year or two and there is a very efficient design for the rectangular cell. It would have six cathodes in it and contain about 25 ft of steel wool. The body of this rectangular cell would be reinforced fiberglass plastic but with an integral lining of a high temperature plastic. I think either cell is so efficient and reliable that I would almost be tempted to flip a coin depending on floor space requirements. Either cell can be used to pull a loaded cathode and to advance the lesser loaded cathodes. Don, what is the configuration of your cell? Duncan: The Pinson rectangular cell has dimensions 2 ft wide, 30 in deep, and 10 ft long-long enough to take a dozen cathodes and anodes. We are currently using six of each but are not up to full capacity as yet. It's a steel tank coated with rubber. We have copper bus bars, which brings to mind that the last cathode in the tank, in one instance, was loaded heavier than the first one. That was probably a function of poor contact between cathodes and the bus bar. You can have erosion of the bus bar and if you don't get current flowing into the anode and out of the cathode, the cells will not function properly. Kappes: Just a few comments on cell design. In an alcohol stripping circuit we are running in Beatty„ NV, we are using PVC pipes for all circuitry piping and a commercial polypropylene electrolytic cell. They seem to be working quite nicely. The cell itself has eight cathodes measuring 18 in2. At six gallons per minute flow into the cell, at an average gold content of about 500 ppm, we seem to get good loading on the first three to four cathodes and not much on the end cathodes. At 12 gallons a minute flow we seem to be seeing gold uniformly along all eight cathodes. We are running at quite a high amperage level, about 400 amps into that cell. Gene McClelland, US Bureau of Mines, Reno Research Center (from the floor): I was associated with a company where the packing density of their steel wool cathodes was much too high and created some short-circuiting problems in their electrowinning circuit. I would like to ask the panel if they can recommend a packing density for cathodes in pounds of steel wool per cubic foot. Hall: The weight of steel wool put on one of our cathodes is 10 lb and the dimensions of the cathode are such that density would be about 0.75 lb/ft3. Duncan: I made a rough calculation and I'm estimating about 2 lb/ft3. Potter: In checking over a number of electrowinning operations, I found apparently very satisfactory operation within the limits that have been mentioned. I have come to a figure of about 0.5-1.0 lb of medium grade steel wool per cubic foot packed as uniformly as possible, of course. One consideration in packing is the fact that there should be good contact between the steel wool and the conductor. Operators tend to compact the steel wool more than would be desirable just to try to maintain good contact.

Jan 10, 1981

The geologist is often called upon to give judgment on the possibilities of reviving a former mining field presumably worked out as far as the evidence then available indicated. From time to time, scarcity and consequent high prices of metals has led to there-examination of many old fields. The possibility of resuming investigation on them where the practical miner ceased work, even where he had the aid of the trained geologist, has long since disappeared.Means of access to mines have been removed and water fills the workings. Hence an indirect mode of attack becomes essential.This method depends mainly on past history, and may be described as a reaching out by faith supported by shrewd guessing from the known to the unknown. Apart from whatever general intelligent observations may be made in situ of the evidence of former mining activity, the method depends largely on the examination of the past history of the field as revealed in the official records, company reports, plans of underground workings, local newspaper accounts, and the testimony of practical miners formerly employedon the field, the' reliability of which has to be carefully sifted. The matter derived from the examination of these sources must next be rigorously collated and correlated where possible. When the review of all individu!1l features and aspects has been completed, tentative and speculative conclusions may be drawn which, though not verifiable before the event, will usually prove to be more serviceable guides in exploratory operations than mere "blind stabbing."As an actual illustration of what is involved in the mode of procedure outlined above, the following is the description of an investigation in which the writer took part.In 1937, during the course of the Commonwealth Aerial, Geological and Geophysical Survey of Northern Australia, a detailed geological investigation was undertaken of the Croydon gold field, situated near the south-eastern. extremity of the Gulf of Carpentaria in North Queensland.The history of the field briefly is as follows: It was discovered in 1885, reached its peak of production 1896, declining thereafter till 1906, when operations ceased. The total production was about 1,000,000 ounces of gold bullion, containing approximately 40 per cent. of silver. The gold bullion was won from flat-dipping quartz reefs, which yielded an average of 2.oz. to the ton, and the maximum depth to which production occurred was 500 feet. Subsequent prospecting below this depth failed to locate further ore.In consequence of the inaccessibility of the mines and the almost total masking of the' surface by alluvium, the investigation of future possibilities became largely an. office ,study, which was conducted under the following headings:-1. Recording of factual data of each mine separately.

Jan 1, 1950

By P. J. G. du Toit

Coal has been mined by hydraulic means in various countries, i.e., the hydraulic excavation as well as the hydraulic transportation of coal has been practiced. The hydraulic breaking (excavating) of the coal dealt with in this report is done with a monitor directing a continuous jet of water against the coal, pressures of the water fed to the monitor range from 1500 to 2500 psi at 1000 to 2100 gallons per minute Transportation of the coal from the face is by fluming if a gradient exists in excess of 2 or, when a favorable gradient does not exist, the coal is pumped from the face by various types of pumps which can also provide a means of hoisting the coal to a higher elevation as required. This report presents: 1.) preliminary design and systems specifications of a demonstration miner (referred to in this report as a hydrominer), 2.) mining configurations showing good promise for typical U.S. thick coal seams in three seam pitch categories, (0° - 7° = Flat, 8° - 250 = Moderately pitching, 26° - 90° = Steeply pitching), along with cost and performance analyses for each system, 3.) a definition of a test program that will provide sufficient engineering data for the design of a water jet cutting head adequate to cut coal in those typical U.S. thick coal seams The cost analysis data showed hydraulic methods to be economically competitive with present thick seam raining methods. It was also obvious from studies of thick seam methods that the hydromonitor coal breaking techniques are more effective in removing most of the coal with its long reach of 60 ft. (or more), is a safer mining system, and produces very low coal-dust content in the air (usually less than 0.25 to 0.5 mg/cubic meter). It is recommended that the USBM sponsor a full fledged continuation of the hydraulic mining program: (a) lab, test, (b) preliminary field test, (c) full scale mine section demonstration.

Jan 1, 1977

By W. J. Birch, R. Farnfield, S. Hosein, C. Johnson

Modern smart phones include accelerometers based on MEMS (Micro Electro Mechanical System) technology giving the possibility to measure both acceleration and orientation. The widespread use of such phones has driven technological development to such a degree that it is now possible to obtain a triaxial accelerometer unit, that also include signal conditioning and analogue to digital conversion, in a package smaller than 1 cm2 (1/2 sq.in) for a relatively low cost.

Feb 6, 2023

By R. V. Higgins

The Bureau of Mines investigated the use of electronic computers for obtaining more information about relative permeabilities of reservoir rock to oil and water. It was found that there are many possible combinations of relative permeability curves that will result in virtually the same recovery versus injection) but they require different times and rates to recover the oil even with different mobility ratios. Permeability curves obtained by the use of non-viscous oil and employed for calculating the waterfloods of viscous oils can lead to serious inaccuracies. For viscous oils) the wettability characteristics in the middle portion of the permeability curve affect recovery nearly as much as other portions of the curve; this) however) is not true for non-viscous oils in water-wet reservoir rock.

Jan 1, 1967

Jan 1, 1885

By Keith Mayhew

Ante la alta demanda de cobre por el crecimiento urbano e industrial y para la construcción de infraestructuras, la industria del cobre necesita una solución para el desarrollo sustentable de los recursos minerales de cobre con alto contenido de arsénico. En ese sentido, Teck Resources Limited (Teck) y Aurubis AG (Aurubis) están trabajando juntas para desarrollar una tecnología que sea aceptable desde los puntos de vista regulatorio, medioambiental, social y económico. Por ello, el presente trabajo señala los resultados obtenidos por Teck-Aurubis conjuntamente, como consecuencia del programa técnico desarrollado desde 2010 para el tratamiento con éxito de concentrados de cobre con alto contenido de enargita usando la tecnología CESL.

Sep 12, 2011

By Jeffiey B. Austin, Maurice Tagami

"The ores of the Iberian Pynte Belt are typically massive sulphide ores with very fine grained mineral textures. EuroZinc Mining Corporation is currently evaluating one of the massive sulphide deposits located near the town of Aljustrel, in South Central Portugal. The deposit contains significant grades of lead, zinc and silver. The ores are comprised solely of sulphide mineralization consisting of pyrite, sphalerite, galena and some secondary copper minerals. Liberation requirements for these ores are typically 22 to 25 microns. A selective flotation process has been utilized to produce separate lead and zinc concentrates for sale to off-site contract smelters.This paper outlines the process test results and describes the process parameters required to optimize the process parameters. Ths test program has been conducted in support of the re-opening of the facilities in Aljustrel. The 3500 tpd mining and milling facility was commissioned in 1990 and operated for 18 months before closing. The previous facility was designed to produce three products using a selective copper-lead-zinc flotation process. EuroZinc Mining Corporation is proposing to re-open the operation, selectively mining from a lead-zinc phase of the massive sulphide deposit and produce only lead and zinc concentrates.Results are presented and discussed.PROJECT HISTORY AND CURRENT PROJECT OBJECTIVESThe EuroZinc Aljustrel Project is a potential major producer of lead, zinc and silver located in the Iberian Pyrite belt of south-central Portugal. The town of Aljustrel is historically associated with mining dating to the time of the Romans. The area is rich in pyrite deposits, and sections of the pyrite deposits contain significant zones of copper, lead, zinc and silver. Mining in Aljustrel during the last century (1900’s) included a major pyrite mining operation, which produced feed for sulphuric acid production. Pynte mining operated from the 1930’s to the early 1970’s and a short-lived base metal operation from 1989 to 199 1."

Jan 1, 2000

By John J. Ginty

The objective of the work reported herein was to evaluate state-of-the-art repeaters used in wireless communications to determine their suitability for use in extending the range of portable and mobile communications in underground mine applications. The scope of the work included wireless repeaters in the frequency range from LF (500 kilohertz) up to the one giga-hertz range. These repeaters included not only single-channel repeaters, that is F1/F1 repeaters for short range simplex party line communications, but in addition, F1/F2 type repeaters currently commercially available in the HF, VHF and UHF bands.

Jan 1, 1975

"INTRODUCTION Industrial utilization of the present submarginal domestic manganese resources of the United States is wholely dependent at this time on the electrolytic manganese process established as the result of 4 years of continuous operation of the Bureau of Mines pilot plant at Boulder City and 7 years' operations of the Electro Manganese Corporation commercial plant at Knoxville, Tenn.Three Kids ore provided the feed for the Boulder City pilot plant during 3 years of operation. Hence, the electrowinning characteristics of the ore have been thoroughly established, making possible accurate estimates for commercial operations.Before the Defense Plant Corporation constructed the leaching plant, the Bureau of Mines conducted an exploration project to determine the extent and grade of the ore reserves. Additional exploration, development, and mining by the Manganese Ore Cc, have accurately determined the tonnage and grade of ore. A large tonnage of stock piled ore is now available for immediate processing, and a considerable tonnage of openpit ore has been stripped of overburden preparatory to mining. Numerous facilities, such as power, water, and housing, needed for an electrolytic manganese plant are already available.All of these factors, as well as plans for installation of scale electrolytic manganese plant facilities, are presented in detail in the chapter entitled, ""Mining and. Electrolytic Reduction of use from Three Kids Manganese Mine."" The Manganese Ore Co. kindly provided information on the present ore reserves and state of development of the mine."

Jun 1, 1945

By D. Randolph Berry

The objective of this program was to develop a system to extinguish coal mine fires by remote sealing of the underground passageways. The system developed had to be versatile enough to function under a wide range of operating conditions, including large variations in passageway geometry, depth of mine, water conditions, both in the mine and at the surface, and rubble in the mine passage. The system developed had to include instrumentation for the remote probing of the passageway prior to sealing, a system for sealing the mine passages, and instrumentation for remote monitoring of the quality of the seal during and after construction. These objectives were successfully achieved during this program. The remote mine sealing capability of the system was satisfactorily demonstrated in a field test conducted at the Eastern Associated Coal Corporation Federal No, 1 Mine in Grant Town, West Virginia.

Jan 1, 1973