Search Documents

By Fredrik Sarvell, Leo-Ville Miettinen, Veli-Matti Uotinen

"Abstract The continued concentration of building activities in cramped areas of city centres means more underground construction and facilities. Demand to minimize execution time and any kind of disturbance to business, general traffic, people and nearby technical structures is increasing. To answer these challenges foundation business has to develop schedule-wise and technically reliable deep excavation and foundation solutions in vulnerable surroundings and challenging soil conditions.Drilled pipe pile wall – RD-pile wall – is a combination of Ruukki drilled steel pipe piles and interlocking sections. Individual RD piles, typical diameters between 219 mm to 610 mm, are connected to each other with interlocks welded to the piles on the automated welding line at the workshop. The matching dimensions of the drilling system and interlocking sections allow the installation of RD piles through stones and boulders and even into the bedrock, if necessary, in a single operation. Installation is done by a down-the-hole hammer (DTH) using the centric drilling system and oversized ring bits or a drilling system consisting of a pilot bit and reamer wings.RD-pile walls have been used as permanent and temporary retaining walls for different kinds of demanding excavations and structures, such as bridge foundation, as quay wall and as sealing structure in rehabilitation of an existing dam. Rigidity and watertightness of the lower end of the RDpile wall is being researched as well as fire design issues examined. One of the most fascinating RDpile wall solution is to utilize the wall as a permanent underground basement wall. Reliable and rigid connection to bedrock decreases the bending moment and deflection of the wall and good fire resistance in addition to large variety of pile dimensions and steel grades gives possibilities to design and execute a cost-efficient basement wall and foundations without temporary retaining wall works. 1. IntroductionIn northern Scandinavian soil conditions, installation of sheet pile walls, or even secant pile walls, is often problematic due to the existence of hard and large boulders in the overburden, and especially when the retaining wall structure should penetrate to or into the hard bedrock. On the other hand, an efficient and reliable piling technique suitable for the demanding soil conditions described above, percussion drilling, has been developed since the 1960’s, and especially from the mid-1990’s, when the concentric drilling method with the ring bit and pilot was introduced. A new retaining wall application, the RD pile wall was developed by combining that drilling method with the widely used retaining wall solution based on steel pipe piles and welded interlocks (a pipe pile wall normally installed with vibratory or impact hammers)."

Jan 1, 2014

Pipe Flow Stability of Concentrated Coal-Water Suspensions in the Presence of an Electric Field

Sep 13, 2010

By E. G. Baglin

As part of an effort to decrease U.S. dependence on imports of critical and strategic metals, the Bureau of Mines investigated three leaching methods for extracting the base metals and recovering platinum-group metals (PGM) from matte prepared from Stillwater Complex flotation concentrates. Because of a limited supply of natural material, synthetic matte of composition similar to matte prepared from natural concentrates was used to devise the extraction sequences. The validity of the sequences was verified with matte prepared from Stillwater concentrates. In two-stage matte leaching, first-stage H2S04 leaching extracted 99 pct of the nickel and iron from the matte but negligible amounts of copper and PGM. Second-stage oxidative leaching with Fe2(S04)3 or FeC13 solubilized more than 98 pct of the copper and no precious metals. Sequential leaching, in which acid and oxidizing lixiviants were added sequentially to the matte without an intervening filtration step, extracted 99 pct of the Fe, Ni, and Cu. A roasting-leaching technique, in which the residue from first-stage leaching was roasted between 360° and 500° C before a second leaching with H2S04, solubilized 98 pct of the copper. The three leaching methods yielded high-grade PGM residues containing more than 98 pct of the PGM in the matte.

Jan 1, 1982

By Dan A. Brown

Outline ? Basic Concept of ACIP Piles ? Factors Affecting ACIP Pile Performance ? Applications: - Favorable Conditions - Unfavorable Conditions ? Design for Axial Loading ? Lateral Loading Considerations ? Summary & Conclusions

Jan 1, 2004

By J. A. Meech, G. R. Baiden

"A dynamic simulation of a mine-mill complex has been conducted using networked microcomputers (IBM PC/AT and IBM PC/XT). These models allow simultaneous operation of an open pit using shovels and trucks, a primary crusher, and a secondary crushing plant. Each process transmits information via the network, linking all operations together. The effects of blasting, ore quality, equipment utilization and configuration on productivity can be studied either interactively or from a report listing at the end of each shift. Programs are menu driven leading the user through the decisions required in day to day operations. The mine-mill simulator is currently being used as a teaching tool at Queen's University to provide senior mining and mineral processing engineering students with an experience and appreciation for the operating problems across the mine-mill interface. The need for coordination and close communication between the mine and mill can be aptly demonstrated using these models. The simulator could be used to contribute to the training of operating personnel in a real mining operation. INTRODUCTIONThis paper describes a computer simulator that is capable of showing the interactions and operating strategies between a mine and a secondary crushing plant. The simulator uses two models developed at Queen's University; one for open pit mining and the second for secondary crushing. PITSIM is a dynamic shovel/truck haulage model origin2lly developed by P.D.D. Chick (1) and K.G. Fytas (2) to solve shovel/truck scheduling problems. CRUSHSOFT is a dynamic secondary crushing plant model developed by R.J. Tucker (3) and C.A. Harris (4) to study alternative operating and control strategies in a crushing plant."

Jan 1, 1987

By K. Zenger, J. Kaartinen, J. Huuskonen, S. Torttila, S. Lähteenmäki, J. Pietilä

"Pyhäsalmi Mine in Finland has a long history of continuous process development. The concentrator processes Cu-Zn-sulphide ore with high recoveries. An on-line flotation simulator has been developed to maintain and further improve the flotation performance. Consisting of a flotation kinetic dynamic model, and interconnected with process control software, the simulator can be used for training new control room operators in various scenarios. For daily operation, the model parameters are continuously adapted to take into account the changing process conditions. On-line simulator tracking the process can provide the process operator new information in several ways: a) values of unmeasured process variables are obtained by displaying the corresponding simulator values, b) predictions of future process states and outputs are calculated and displayed, c) information of changing process parameters can be used as an indicator of e.g. change in the processed ore type. This paper describes the adaptive simulation system and its usage at the Pyhäsalmi concentrator.IntroductionPyhäsalmi massive sulphide orebody is located in central Finland. Operation of the mine started in 1962 and it is currently producing copper (Cu), zinc (Zn) and sulphur (S) concentrates. The concentrator control and optimization system has a long history of successful continuous development during the past decades (see e.g. Huuskonen & Moilanen, 2010). An on-stream analyzer has been a part of the automatic process control since 1968 (Lähteenmäki, Miettunen & Saloheimo, 1999). First control algorithms based on a flotation mathematical model were developed in 1971 (Koivistoinen & Miettunen, 1985). In 1990’s the development of a froth machine vision systems started (Kaartinen, 2009; Kaartinen, Roine & Hätönen, 2009). More recently Pyhäsalmi Mine Oy has been involved with several national development projects dealing with particle size distribution measurements (Kaartinen & Tolonen, 2008), spectral analysis of flotation slurries (Haavisto, Kaartinen & Hyötyniemi, 2008), and dynamic simulation of flotation processes. The latter topic is further elaborated in this paper."

Jan 1, 2015

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

The mechanization of the coal industry in New South Wales involved the introduction of large face and transport machines. The trend is towards still higher capacity units with .greater horsepower and it became apparent that a potential risk of damage to the hearing of workmen existed. In order to assess whether the sound levels were SUfficiently high to impair the hearing of workmen a sound level survey of all major operations in the industry was carried out by the Mining Engineering Division of the Joint Coal Board.The results indicated ·that the operations could be classified into three categories of risk, probably hazardous, of doubtful hazard due to the intermittency of the operations, and of low hazard.Legislation has subsequently been enacted requiring the wearing of hearing preservation aids in some of the probable risk operations.

Jan 1, 1974

By M. A. Trvits, M. Cummins, A. C. Smith, T. P. Mucho

This paper evaluates the effectiveness of remotely applied nitrogen-enhanced foam to aid in efforts to isolate and suppress a mine fire. The foam, in combination with a remotely-installed cementitious mine seal and a novel borehole pressure sampling methodology to determine the location of the suspected ignition source, was used to help control ventilation and inert the area surrounding the suspected ignition source by isolating it from oxygen. This allowed mine rescue teams to safely enter the mine, seal the area, and begin recovery operations to successfully return the mine to full production.

By Abraham Lindo

"Blasting plays a key role in hard rock underground mining. It is by nature a violent and destructiveextraction method designed to economically fragment the rock into a suitable size for it to be loaded and hauled as part of the specific mining process while controlling the amount of damage to the surrounding rock mass."

Jan 1, 2016

The C.S.I.R.O. acid alumina process employs the essential steps of digestion, hydrolysis and calcination to produce pure alumina from ores too high in silica or too low in grade for the Bayer process. The two latter stages have been described in some detail previously but the digestion stage requires separate discussion since ores vary widely in composition and reactivity. Kaolinitic clays require roasting to 800°C to render the alumina soluble in the 11 per cent sulphuric acid used in the process while some ferruginous laterites require roasting to reduce the reactivity of iron minerals.The iron content of pregnant solutions is kept at a low figure by digesting at temperatures where the solubilities of ferric oxide or basic ferric sulphates are small. A two-stage, counter-current digestion is necessary to extract a high percentage of alumina from the ores and to produce a basic pregnant liquor with an SO3 : AI 203 ratio of 1'\1 suitable for high temperature hydrolysis. The second stage of digestion, called the modification stage, treats slightly acid liquors with excess of ore in the temperature range 1200-1400C.The first stage operates at 170°-1900C to extract further alumina from modification residues, using recycled acid obtained from later steps of the process. Both temperature ranges are critical for economic operation and for proper control of the iron content of solutions. In batch experiments, 30 min is regarded as a suitable retention time for digestion and modification; ores which require much longer than this are less suitable for the process. Impurities such as silica, and titanium and vanadium oxides are discarded in the residue along with iron oxide, and do not contaminate the final product. Bivalent metallic sulphates such as MgSO4, can build up in the circuit to a very considerable degree without affecting product purity.Comparison with other processes shows that the C.S.I.R.O. process is superior for control of contamination by iron, which is the major problem in acid processes. The pure intermediate product (3Al203.4S03.9H20) is also more convenient for calcination to alumina than the hydrated aluminium sulphate usually recovered in other processes. Detailed cost comparisons must await pilot-plant evaluation of the C.S.LR.O process.

Jan 1, 1964

By Rita D. Sylvester

"THE BUREAU OF MINES was established in the public interest to conduct inquiries and scientific and technologic investigations concerning mining and the preparation, treatment, and utilization of mineral substances; to promote health and safety in the mineral industries; to conserve mineral resources and prevent their waste; to further economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting these industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau to ""disseminate information concerning these subjects in such manner as will best carry out the purposes of this Act.""In accordance with that directive, the Bureau reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-Bureau sources. The number of these reports, the wide range of subjects they cover, and the variety of mediums in which they appear make the kind of list and index presented III this special publication both necessary and valuable. This issue describes Bureau reports and articles published during the period January 1, 1960 to December 31, 1964. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960,2 and the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960.3 It supersedes the annual lists of Bureau publications and articles from January 1 to December 31, 1960/ from January 1 to December 31, 1961,5 from January 1 to December 31, 1962,6 and from January 1 to December 31, 1963,1 The leading general and technical libraries of the United States maintain files of the Bureau's publications. A list of these libraries appears immediately following this introduction. BUREAU PUBLICATIONSBecause some series of Bureau reports contain both free and sales publications, and because the cost of sales publications varies, prices are indicated in the individual listings of all publications for which charges are made."

Jan 1, 1964

By Mehrotra G. M, Frohberg M. G

Based on the concepts of statistical thermodynamics of athermal mixtures, an approach is developed which is capable of quantitatively explaining the thermodynamic properties of binary silicate systems. Expressions for the ionic fractions of various anionic linear and nonlinear chain polymers are derived. The developed expressions for free energy of mixing are tested by applying these to the system PbO-SiO2. The ionic fractions of various chain polymers in this system are calculated. The two cases, namely, of linear and nonlinear chain polymers are compared with each other.Limitations of earlier models are pointed out.

Jan 1, 1975

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to date and more nearly in line with present operating and safety practices in the industry. The rules are intended to supplement existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment, or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By Turnbull A. G

Thermodynamic calculations based on the ideal system NiO - Fe203 - H2(g) - CO(g) - H2O(g) - CO2(g) show that it is not possible to selectively reduce nickel oxide in the presence of hematite because ferronickel is the zero-valent nickel-containing product. The calculations show that temperature, reducing atmosphere composition and oxide to reductant ratio have a marked effect on the nickel content of the ferronickel alloy and the amount of nickel reporting jn the alloy. The general trends based on the calculations correlltte well with experimental observations.

Jan 1, 1980

By P R. L Browne

Study of geothermal systems in the Taupo Volcanic Zone (TVZ) has significantly advanced our understanding of the processes of epithermal mineralisation. The three main lessons learnt are: 1. knowledge of their chemical anatomy; 2. precious metal transport and deposition; and 3. hydrothermal alteration zoning. These are described in the context of ore formation and exploration.

Jan 1, 1997

Safety rules for installing and using electrical equipment in and about coal mines covered in this information circular supersede those previously included in Bureau of Mines Bulletin 514, issued in 1952. This revision brings these rules up to data and more nearly in line with present operating and safety practices in the industry. The, rules are intended to supplement existing existing Federal and State regulations, and no provision shall be construed to oppose or supersede any provisions of the Federal Mine Safety Codes, the Federal Coal Mine Safety Act, or the mining laws of any State. The rules were designed to permit progress, such as application of new or improved materials and equipment or use of new practices where these materials, equipment or practices retain or improve the level of safety established by these requirements. It is hoped that they will fill the need for a concise edition for mine electricians and electrical engineers, especially those who do not have ready access to more detailed rules or codes.

Jan 1, 1964

By Persio P. Rosario

Crushing has proven to be of fundamental importance in mine mill integration at Highland Valley Copper (HVC). Highland Valley Copper has achieved large throughput and good quality control through the gyratory crushers by proper blast design and better gap control. The next step, in optimizing the mine mill relationship, is evaluating the crusher liner wear and its shape influence on performance and product size reduction. To do this a laser measurement device has been developed and data is being recorded on the concave and mantle liner wear. This paper will outline the work to date and indicate specific objectives of the work.

May 1, 2002

By Matthew I. G

A new process for leaching zinc sulphide concentrates with gaseous mixtures of SO2 and O2 in aqueous solution is described.The reaction of SO2/O2 with Rosebery, Mt. Isa, Broken Hill and Elura zinc concentrates yields zinc and iron sulphates, elemental sulphur and some sulphuric acid. Rates of zinc extraction are controlled by a surface chemical reaction without apparent interference from the elemental sulphur layer for SO2 concentrations up to 9 per cent in the gas phase. Pyrite in concentrate exerts an activating effect, possibly through galvanic interaction with the sphalerite. Metal extractions are dependent on SO2 and O2 tenors of the gas, particle size, and the acidity and zinc content of the solution, but are independent of the ferric ion level. Extractions also reach maxima at about 85°C.Generation of acid may be prevented by conducting the reaction in the presence of ferrous iron and at acidities of 40 g/l or greater. Zinc and iron levels in Elura lead concentrate may be reduced by leaching with SO2/O2.

Jan 1, 1981

By Å. Kruukka, H. F. Broicher

The iron ores of the Kiruna mine in Sweden are of exceptional quality except for the phosphorus content in certain zones of the orebody. The prevention of mixing ores high in phosphorus with those low in phosphorus has always been of significant economic importance. The ongoing introduction of tele-mining and automatic haulage by LHDs requires new means in the field of quality control underground, as the experienced miner as well as the underground laboratory assistant no longer are involved in the process. As of 1998, LKAB has been testing prototypes of LIF (laser-induced fluorescence) analyzers for non-contact and real-time measurement of the phosphorus content of ore being transported by LHDs from the stopes to the respective ore pass assigned to a certain ore quality. The principles of the analysis of laser-induced fluorescence, the different test phases and results are described and conclusions made. With bulk sorting of ore underground, the mining engineer supports the efforts of the metallurgist in the processing plant.

Jan 1, 2002