Search Documents

By S. Eck

In previous work the influence of the casting speed on the flow field and the shape of the solidification front in an industrial 0.82 x 0.25 x 0.8 m³ bronze caster had been investigated. Both numerical and experimental model represented 1:1 the real caster geometry. A comparison of the results of both numerical and experimental models for the flow during the casting process showed a good agreement in the qualitative velocity fields (flow direction and vortex formation). This work represents a parameter study of the numerical model with variations of the turbulence conditions at the inlet in order to clarify their influence on the flow field in the caster. In order to find the best boundary condition at the inlet, the numerical calculations for water have been compared with the measured flow fields in the water model. The new boundary conditions were then applied to the numerical model of the bronze casting process.

Jan 1, 2009

By Russell E. Griffin

Dielectric constants and dissipation factors were measured by the Bureau of Mines for 13 simulated lunar rocks over the 20-to 100-megahertz frequency range by means of the susceptance-variation method. Measurements were made at room temperature and normal atmospheric pressure. Results are presented and some comparison is made with data reported by others. The rocks used include a broad range of physical characteristics and chemical compositions from the large areas of volcanism in Oregon and northern California, and two nonvolcanic types. These rocks make up a suite of rock standards used by a group of laboratories engaged in lunar research. The data presented will add to the basic scientific and engineering knowledge needed to utilize extra-terrestrial mineral resources for support of future space missions.

Jan 1, 1974

Mineral deposits in New Zealand whose origin can be ascribed to primary magmatic segregations are associated with mafic-ultramafic complexes related to two orogenic episodes which took place during Palaeozoic and Mesozoic times. These mafic-ultramafic complexes are essentially of two types. One is ophiolitic and has podiform chromite mineralisation presumably formed below a spreading ridge. The other type occurs as intraplate layered intrusions in which Fe-Cu-Ni sulphides and Fe-Ti-V oxides have formed as a result of liquid immiscibility with the host magma, and have subsequently accumulated by gravity means. Generalised descriptions are given for some deposits in NW Nelson, Fiordland and Marlborough districts.

Jan 1, 1980

By Holger Witthaus

Various seam conditions had been examined during longwall production at RAG German hard coal mines. Based on the field data a prediction method was developed considering separation planes as influencing factors for roof falls at the face. The characteristics, orientation, and density of separation are important factors on the occurrence of roof falls. In addition to geological influences, the performance parameters and geometry of support must be considered and optimized for the prediction and prevention of roof falls in a longwall face. Based on detailed macro- and microscopic investigations of e coal seams considering various ranks of carbonization, the origin and characteristics of separation planes are determined and a strata-specific influence on roof fall is interpreted. It was assessed that the coal face fracturing and displacement caused by the stress depend on the floor and roof strata conditions due to activation of the existing separation planes. Field studies are shown giving an idea of influences by advance rates of the longwall face, support delay and hydraulic pressure to the roof control in longwall faces in depth of more than 3000 ft. The analysis includes the application of specific software developed for longwall roof fall prediction as a result of a European research project. The software allows a laminar graphic display of roof fall probability, which is used for recognition of risk areas and risk management.

Jan 1, 2009

By Jerry T. Shelby

Surface and underground mining operations require equipment with high power output ratings. Haul trucks, loaders, dozers, and other equipment need increasing horse-power to meet production demands. To get more horsepower out of the engines driving the equipment, most manufacturers use turbocharging. Detroit Diesel puts the number at about 90% turbocharged, while Caterpillar estimates 75% to 80% of all its equipment is turbocharged. Turbocharging increases the power output and overall engine efficiency. But it presents some maintenance and operational problems that were not factors when only naturally aspirated engines (nonturbocharged) dominated the scene. A turbocharger is an exhaust-driven air compressor. Using the waste energy in the engine exhaust, a turbine wheel is driven. This wheel is connected by a common shaft to a compressor wheel. The shaft is supported by two plain bearings, or bushings. As the turbine wheel is rotated, the compressor wheel continually compresses the intake air to the cylinders. Compressing the intake air means that more air can be put into the cylinder to burn more fuel. The more fuel the engine can completely burn or combust, the more horsepower the engine can produce. Even though the turbocharger is a relatively simple device, it is a sensitive engine component. It requires special consideration at engine start-up and shutdown. Being freewheeling and exhaust driven, turbochargers can experience temperatures of 540°C 1000°F) and rotational speeds of more than 100,000 rpm. Due to those temperatures and speeds, lubrication is critical to the operation and life of a turbocharger. The turbo is located high on the engine, with the oil supply running through an external line from the sump. The recommended practice is to start the engine and allow it to idle for a few minutes before any revving or loading. This allows the oil to reach the turbo and properly lubricate the bearings before high rotational speeds are seen. Turbo oil supply lines can be as long as 1.5 m (5 ft). Depending on ambient temperatures and oil viscosity, it can take as long as 30 seconds for oil to reach the spinning turbo. However, as little as five seconds without oil can damage the turbo's bearings, reducing its life and overall efficiency. Lubrication problems seen at shut-down can also significantly affect turbo life and efficiency. Manufacturers recommend an idling period of five to seven minutes before engine shutdown. This allows the turbo to slow down and cool off somewhat to help prevent oil coking and bearing damage. When the engine stops, so does the oil supply. There is very little oil left on the bearing surfaces and in the turbo oil supply passages. The immediate heat transfer from the turbine wheel to shaft, bearings, and turbo body literally cooks what is left. This high heat without oil flow can cause bearing deformation by actually melting some of the bearing material. The rapid oil oxidation and coking will restrict oil passages, damage bearings and shaft. Besides heat soaking, there is another problem. If the turbo is spinning at high speeds when the engine is shutdown, the turbo must spin-down to a stop without oil flow. With the large size of turbos used on mining equipment, this spindown time without oil can be for as long as 10 to 20 seconds. Fortunately, lack of lubrication at start-up and shutdown and the subsequent bearing damage can be prevented by oil injection devices. These devices hold a reservoir of engine oil. The oil is injected to the turbocharger bearings immediately on start-up and for several minutes after shutdown. Oil injection devices are spring loaded, hydraulic accumulators. They are actuated at start-up by a solenoid wired to the starter motor. Engine oil pressure charges the accumulator during normal operation. Upon shut-down and loss of oil pressure, the device provides oil to the turbo for about two or three minutes. With an oil injection device, the engine can be started and immediately driven without fear of turbo damage. Also, an abrupt shutdown will not damage the turbocharger since the device will continue to lubricate for two or three minutes. A word of caution. Be sure the oil injection device provides positive oil displacement (pressurized oil flow). Do not use a gravity-flow device. Unless it is a true accumulator, the device could starve the turbo for oil on start-up, Ask for start-up and shut-down pressures and delivery times before considering installation. Keep the oil clean, and follow the manufacturer's recommended oil change intervals. These intervals are usually shorter than with naturally aspirated engines. Use oil with a CD rating designed for diesel applications. A multiviscosity oil is preferable. Use a synthetic engine oil, such as Mobil's Delvac 1, Gulf's Super Duty II, or Chevron's Sub-zero Fluid. Synthetics have much better flow properties at low temperatures. They also have greater oxidation stability (they can take the high heat of turbo-bearing lubrication. And they produce fewer deposits because they are more thermally stable. But synthetic oils do cost more - two or three times more. One additional point - maintain the air intake system. Since all mining is usually in a dusty environment, air filters should be changed regularly and intake systems should be checked for leaks. All intake air passes through the turbo. Any dirt or abrasives entering the turbo will damage the unit and shorten its life. While mining is a heavy duty business with severe operating conditions, you can get the life from your turbocharger that you expect by following a few simple steps: • equip the turbo with an oil-injection device to provide lubrication on start-up and shutdown; • change the oil and filters regularly; and • use the proper oil-synthetic, if possible.

Jan 3, 1987

By Paul S. Fisk, Arne Fareth, Julie Frietas, Francis Lo, Fidel L. Mallonga

INTRODUCTION This report describes the inspection of parts of the New Croton Aqueduct (NCA)undertaken for the New York City Department of Environmental Protection (NYCDEP)by Parsons Brinckerhoff Quade & Douglas, Inc., (PB) in association with Montgomery Watson Engineers of New York, P.C. (MWH). Support for the inspection was provided by AFC Enterprises, Inc., under Construction Contract CRO-333, “WM-11 New Croton Aqueduct Rehabilitation and Inspection Program.” The scope of the inspection work under CRO-333 included assessing the condition of the 10.3 km (6.4 mile) long, pressurized section of NCA and inspection of shafts, head houses and blow-off structures in both the pressurized and gravity sections. The CRO-333 inspection continued investigation work begun under ContractCRO-196, which ran from 1993 to 1997. The CRO-333 inspections were conducted from November 2004 to September 2005. Background The New Croton Aqueduct was put into service in 1891 to deliver water from the Croton River Watershed in Westchester County to consumers in New York City. Figure 1 shows the location plan of Croton Water Supply System. The design flow into Jerome Park Reservoir was 12.7 m3/s (290 mgd) and into the135th Street Gate House, further south, was 10.9 m3/s (250 mgd). The NCA has been operated as a gravity conduit from Croton Lake to Gate House No. 1, just north of Jerome Park Reservoir, since its original construction. The length from Gate House No. 1to 135th Street, which includes a major siphon under the Harlem River, has been operated under pressure. Croton Lake gate house, the north end of the alignment lies at Station 4+75; Shaft 33, the south end of the alignment lies at Station 1628+05. The diameter of the tunnel is 3.2 m (10.5 ft) in the siphon and 3.7 m (12.3 ft) in the Bronx and Manhattan sections. The pressurized sections, constructed in rock, consist of a brick lining surrounded by a mortared and grouted rubble backing. Figure 2depicts a typical tunnel cross section. The objective of the shaft and tunnel inspections was to locate and document defects, such as leaks, deterioration of lining material, cracks, spalls, delaminations,

Jan 1, 2007

By James J. Meadows, Jason D. Pampena, Emanuele G. Cauda, Lauren G. Chubb

Exposure to respirable crystalline silica (RCS) can cause serious and irreparable negative health effects, including silicosis and lung cancer. Workers in coal mines have the potential of being exposed to RCS found in dust generated by various mining processes. The silica content of respirable dust in one single mine can vary substantially over both time and location. The current monitoring approach for RCS relies on the use of traditional air sampling followed by laboratory analysis. Results generated using this approach are generally not available for several days to several weeks after sampling, and this delay prevents timely and effective intervention if needed. An alternate analytical method is needed to reduce the time required to quantify the RCS exposure of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has developed a new method using commercially available portable infrared spectrometers for measuring RCS at the end of the sampling shift. This paper will describe the application of the new field-based RCS analytical process for coal mines, including the use of the new method with the existing Coal Mine Dust Personal Sampler Unit. In a case study conducted by NIOSH with a coal mine operator in West Virginia, field-based RCS analysis was completed at a mine site to evaluate the new technique. The RCS analysis results obtained by the field-based method in this case study showed sufficiently strong correlation with results obtained by the MSHA standard laboratory analysis method to allow the mine operator to use the field-based method for evaluating process improvements.

By W. R. Hardwick

This paper describes open-pit mining methods and practices at Copper Cities Division of Miami Copper Co, in Gila County, Ariz. It is one of a series being prepared by the Burea of Mines on mining methods, practices, and costs in various mining districts of the United States. A similar program, conducted from 1928 to 1939, provided technological information on the development and conservation of our mineral resources and assisted operators and engineers in evaluating and developing new mineral deposits. This circular contains a brief history of the district and describes the Copper Cities deposit, with particular emphasis on a detailed description of those characteristics--physical, economic, or engineering--that affect the choice of mining method. Prospecting and exploration, sampling and estimation of tonnage and values, development, and mining (including breaking ground, loading, hauling, ore control, and auxiliary operations related to mining) are described, Percentage of extraction, production rate, safety, first aid, Eire prevention, mine organization, and processing plant are discussed briefly, The final section gives such costs, on a percentage basis, as are available for publication. Where relevant, some information on the Castle Dome mine is included.

Jan 1, 1960

By E Jak, P Hayes, J Chen, M Shevchenko, E Nekhoroshev, D Shishin

Recent decades have seen significant advancements in analytical and experimental techniques, thermodynamic theory, and computational capabilities in high temperature research which are particularly timely to address the challenges of increasingly complex and variable feedstocks in both primary and secondary pyrometallurgical processes, the need to optimise and improve them. Currently a research program is in progress on the development of the 20-component multi-phase thermodynamic database for pyrometallurgical smelting, refining and recycling systems describing thermodynamics and phase equilibria of molten slag, matte, speiss, salts, alloys and associated solids. The integrated experimental and modelling program has been supported for nearly two decades by several consortia of 14 major international companies with over 30 operations around the world, integrates many components, incorporates many in-house developments, and brings together many different groups of professionals of different levels from junior and mid-career to senior from both industry and university sectors. The aims of the paper are:  to outline the many components and issues of the overall program including analytical, experimental and thermodynamic modelling research as well as implementation of the results in industrial practice, professional education, planning and organisation issues.  to highlight the opportunities, challenges, and possible solutions.  to present these to all different groups of professionals involved in the current program.  and thus, importantly, to facilitate possible future further developments and collaborations in the field of phase equilibria and thermodynamics of complex high-temperature systems.

Jun 19, 2024

By I. Jauhari, F. Stober, D. Fowler, B. O. Wasmund, T. Miraza, C. Nichols, A. Taofik Hidyat, K. Said

The existing PT Aneka Tambang (Antam) ferronickel smelter located at Pomalaa, Indonesia consists of two RKEF lines with reduction furnaces nominally rated at 17 MW and 18 MW, respectively. The low power densities and heat fluxes allowed both furnaces to operate with falling water film shell cooling systems. The furnace campaigns comprised a 5-yearly cold shut -down for metal taphole area rebuild and a 10-yearlysidewall and hearth perimeter repair. Towards the end of these campaigns the furnaces would typically be operated at below nominal power due to excessive sidewall temperatures. In January 2001 Hatch performed a smelter study which proposed options which indicated the possibility of a single furnace operation for the smelter, elimination of lime addition and transition to shielded-arc operation with associated efficiency and throughput gains. This paper discusses the process of uprating the second?line furnace capability from 18 MW to 32MW following the decision by Antam to implement the recommendations proposed by Hatch. It will cover the development of scaled-up furnace design basis by Hatch and Antam with the enabling application of Hatch cooling and binding technology. To optimise the capital cost and maximise Indonesian supply content and post installation support, the scope was carefully and clearly divided between Hatch and Antam. The challenges, set backs and valuable learning experiences gained during the implementation of the retrofit include; ?The support and re-use of existing roof system and challenges presented in re-use of existing crucible support steel. ?Training and technical assistance for Antam operators to perform refractory and copper cooler installation and maintenance of crucible integrity technologies. ?Hearth integrity during start-up and development of an initial charge and start-up procedure to achieve planned thermal expansion of the hearth prior to bath formation ?Implementation of a sidewall hold-down system within the refractory sidewall due to space constraints ?Existing furnace foundation reinforcement to overcome lateral forces on furnace piers during crucible support steel expansion ?Conversion of an open-loop gravity feed cooling water system to a closed loop pressurised system with integrated emergency gravity feed and backup system ?Existing water treatment system and pumping system improvement and modification to meet copper cooling system requirements ?Integration of the new instrumentation control system designed by Hatch to increase performance of the furnace monitoring system and operation ?Uprate transformer capacity from 25 MVA to 40 MVA to meet with requirement of Shielded- Arc Furnace Operation.

Jan 1, 2007

By Shaw-Shong Liew

This paper presents the design concept using floating piles to support 2500Ton oil storage tanks on a very soft alluvial clayey soil of about 40m thick in Riau Province of Sumatra, Indonesia. The floating piles of various penetration lengths were designed to support seven numbers of such storage tanks seating on a 20m diameter and 500mm thick reinforced concrete (RC) circular raft. The pile points have been strategically located at the RC raft. Varying pile penetration lengths have been designed to minimize the angular distortion of the thin RC raft and the out-of-plane deflection at the tank edge. Vibrating wire strain gauges were installed at different levels inside the ø350mm prestressed reinforced concrete piles to measure the load transfer profile during the static load tests and water-loading test. The installation and interpretation of the instrumentation are described and discussed. Boreholes, in-situ tests like piezocones, vane shear tests and standard penetration tests, and laboratory testing were carried out to obtain geotechnical parameters for the pile designs. Static load tests were also carried out on the spun piles of varying lengths of 24m, 30m and 36m respectively. It has been demonstrated that the floating pile system can be a cost effective design to support heavy structures on very soft compressible deposits with satisfactory performance. Finally, the design concept validated with the results of instrumentation is discussed.

Jan 1, 2002

By Zephaniah Varley, Dominic Parmantier, Paul Schmall, Richard Martin, Red Robinson

Sequential excavation of the Beacon Hill Station has been accomplished in highly complex and inter-layered sand, silt, and clay soils with multiple perched groundwater tables. Successful excavation has required the installation of a deep dewatering well system used to depressurize sand layers above and within the excavated tunnel faces. In addition, the presence of sand layers in the crown of the Platform Tunnels required jet grouting at depths of up to 49m (160-ft). This paper discusses the design intent, construction, and effectiveness of the dewatering system and the selective jet grouting of sand horizons and shaft break outs for the successful construction of the deepest SEM station excavation ever completed in the United States.

Jan 1, 2007

By Javier Illanes, Maurice Moore, Felipe Moroni, Rafael Acosta

Any organization that subjects its activities to a continuous improvement process must be able to adequately measure the results of the implemented changes in order to pursue better results over time. This is no different for mining companies. When it comes to blasting, an accurate fragmentation analysis can correlate blast design and rock mass parameters to particle size distribution, enabling us to further analyze the correspondence of specific design patterns, applied to specific rock mass properties and the result in measured fragmentation indicators, such as P80 and fines percentage.

Sep 30, 2022

By Eric Low

Raising capital by issuing debt or equity is necessary in almost every corporation. In the field of corporate finance, the raising of capital is a heavily-studied topic. However, some of what is studied on this topic in corporate finance is not applicable in the mining industry. There are also many financing options that were created for the mining industry such as flow-through shares, prepaid forwards, and royalty sales. The cyclical nature of the industry makes the risk-return profile of financings more difficult to estimate than in other industries. Additionally, the methods used to assess firm value are different than other industries, as the values of orebodies are not included on balance sheets. For precious metals companies, which are a hedge against most other securities, there are additional complications with determining investor expectations and cost of equity. This thesis puts forth a decision-making framework to explain mine financing choices from the perspective of mining companies. The approach is threefold. First, all of the major equity and debt financing instruments available to mining companies are presented and analyzed. Each financing method is assessed on a wide range of criteria. Next, these concepts are applied in case studies of four companies: BHP Billiton, Barrick Gold, Teck Resources, and Noront Resources. For each company, the overall choice of financing methods is shown and analyzed. The effect of financing choices on the weighted average cost of capital (WACC) is calculated. The final section deals with case studies of individual mine finance decisions during the past two years.

May 1, 2011

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005

By Hans W. Schreiber

Most geologic and mining engineering consulting firms* began to experience the recession with declining billing levels, number of inquiries, and proposal requests in late 1981 or early 1982. As of today, most of them have been functioning at reduced income levels for nearly a year. And while many consulting firms have apparently reached a stabilized income level, they can see little prospect for attaining normal (pre-late 1981) billing levels and income for the remainder of 1983. A few firms have escaped being affected by the recession. Such com panies almost without exception are small (fewer than 20 personnel), offer a limited range in technical capabilities, and tend to be highly specialized in a particular niche. They include those specializing in the heap leaching of precious metals ores, in ground water testing programs, and in the derivation of computer-aided programs to monitor particular mineral processing functions. Those firms affected by the economic downturn have instituted a variety of policies and undertaken actions to cope with significantly reduced incomes to bring fixed costs in line with the depressed demand for services. These changes fall into the following broad categories: • management and management practices; • markets and market definition; • marketing and the pursuit of assignments; and • administration and personnel relationships. Not all of the perceived changes have necessarily been instituted by every consulting firm, and any one appears sporadically instituted. Management and Management Practices In favorable times the managers, and often the owners of the equity, of consulting firms tend to concentrate their attention on the part of the business they find most satisfying and enjoyable. For some, this means acting as project or assignment leaders, even undertaking a specific technical aspect of the job. For others, it means constant marketing with the associated heavy travel and entertainment schedules. In unfavorable conditions, such as the current recession, managers tend to spread themselves far more thinly, expending time and effort on all facets of the business including marketing, proposal preparation and cost estimating, budgeting, general administration, accounting and cash flow monitoring, project/assignment overview, and actual client work. The manager who in favorable times concentrated on client work is now less billable. The manager who concentrated on marketing is somewhat more billable. The manager now needs to pay attention to and expend equal effort on each facet of the business just to keep all the facets in relative balance. Falling behind schedule on a client job or carrying an unduly large percentage of accounts receivable exact a cost to the firm. Clearly the absolute cost to the firm is the same whether demand for service is good or slack. But in periods of slack demand the firm is frequently less able or even unable to bear such costs. Marketing and Market Definition Markets appear to have undergone some significant changes: • Federal and state governments have assumed a greater importance as providers of work vis-a-vis both industry and private groups. • Projects with increase-in-capacity aspects have given way to projects with maintenance or reduced operating cost aspects. • Projects searching for new deposits of minerals in generally new locations have given way to projects reviewing known mineral districts or known deposits. • Industrial mineral and mining companies have exhibited a great propensity to cut back the use of consultants and to undertake as much work as possible in-house. Further-more, a number of industrial mineral and mining companies have entered the competitive arena with consulting firms, submitting proposals (usually to the federal government) in an effort to keep their staffs intact and occupied. In response, consulting firms have reevaluated their capabilities by reviewing old work and reassessing personnel. The purpose is to broaden the services offered and the potential client base, thus redefining the available market. For example, a firm specializing in assessment of technical and cost parameters of a deposit would normally assist a prospective lender in judging the deposit's suitability for project financing. That same company could easily expand into the field of analyzing production costs for an individual operation -something that is needed in periods when lower prices reduce profit margins. Similarly, a firm that has confined such economic assistance to commercial banks could expand to provide its expertise to other lending and even equity buying in-stitutions such as insurance companies. Marketing and the Pursuit of Assignments With few exceptions, consulting firms have significantly increased their

Jan 2, 1983

By T. G. Carter

Support system design for tunnels and underground excavations has for many years relied heavily on the use of rock mass classification systems and the Hoek-Brown failure criterion as a means for characterizing rock mass behaviour. Because of their development, both the GSI system and the Hoek-Brown criterion admirably characterize most ?normal? rockmasses from the viewpoint of their behaviour for rock excavations. They, however, run into difficulties when applied at the two ends of the rock competence scale. This is largely because block size and incipient strength are such that rockmass behaviour in these domains tends not to be controlled by interblock shear strength but rather by material strength. At the low end of the rock competence scale (UCSi <<15 MPa and GSI generally <30) discontinuities play less of a role and rock mass strength tends to matrix strength. Similarly, at the high end of the scale (GSI >>65, mi>>15), because discontinuities are now widely spaced, block size becomes so significant that again, intact material behaviour rather than the fracturing becomes the dominant factor controlling rock mass strength. In this paper several case examples are presented to illustrate the application of the high-end (spalling) and low-end (weak ground) transition Hoek-Brown relationships proposed by Carter, Diederichs and Carvalho (2007) as a basis for better defining rockmass behaviour at the extreme ends of the rock competence scale.

Jan 1, 2008

By R. L. Virta

Four companies mined ball call in four states in 2009, H.C. Spinks Clay Co. Inc. (owned by Lhoist Group), Kentucky-Tennessee Clay Co. (owned by Imerys Group), Old Hickory Clay Co. and Unimin Corp. Production, on the basis of preliminary data, was 820 kt (904,000 st) with an estimated value of $39.4 million. That was a 15-percent decrease in tonnage from 967 Mt (1.1 mil-lion st) with a value of $44.3 million that was produced in 2008. Tennessee was the top producing state with 59 percent of domestic production, followed by Texas, Mississippi and Kentucky. About 71 percent of production was airfloat, 18 perc

Jun 1, 2010

By T. Holmes

Investigations reveal that the throughput difference between a perfect production day and the average is often on the order of 40%, and that bulk solids handling system deficiencies are the largest (>50%) class of lost opportunities. Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. To reduce or eliminate bulk solids handling problems in an existing system requires an analysis of troublesome handling equipment – for example, a concentrate transfer chute that experiences plugging, poor flow to the furnace, unacceptable dust generation, and spillage. These problems often lead to significant maintenance costs related to downtime and personnel time. Understanding the cause and cost of flow issues is the first step in troubleshooting the problem. Next, measuring the material’s flow properties is critical to providing design data required to develop a comprehensive scientific solution. In the case of a new installation, the design data is required to properly design the system right first time and prevent flow problems from occurring so that the new equipment works correctly from start-up. This paper highlights the cost of material handling problems and discusses the best approach to evaluate material handling system deficiencies. A case study is given of how Anglo American's operation in Barro Alto Brazil enjoyed a 5-month payback from a bulk solid transfer chute debottleneck project. INTRODUCTION When operating a plant or designing a greenfield or brownfield operation, the intent is to have perfect production days (PPD) each and every day. Money is made by moving material through the plant in a controlled manner to produce the desired product. Mining operations and copper concentration processes are at the most basic level a practice in bulk solids handling (BSH). Unfortunately, many of the project planning steps are overlooked, particularly related to BSH. Investigations reveal that the throughput difference between a PPD and the actual average is often on the order of 40%, and that BSH system deficiencies are the largest (>50%) class of lost opportunities (Wellwood, 2017). Root causes for underperformance of elements in material handling systems can often be traced back to the detailed design and even study-stage oversights. BSH issues are essentially baked into the fabricated plant and left to operations to accept the deficiencies and deal with them for the life of the mine. These deficiencies then become part of the normal operation of the mine and plant.

Jan 1, 2019

By Staff

The goal of the U.S. Bureau of Mines diesel engine research program is to reduce exhaust emissions from diesel-powered equipment used in underground mines. This research has led to significant advances in aerosol measurement and to the development of more effective emission controls. This Information Circular contains reports of some of the presentations made at the Bureau&apos;s Information and Technology Transfer Seminar on Diesels in Underground Mines given in Minneapolis, MN, on September 29-30, 1992. The seminar emphasized the measurement and control of diesel particulate matter emissions. Topics covered include a discussion of the health issues associated with the use of diesel equipment underground, an overview of regulations, measurement techniques for diesel exhaust aerosol, levels of diesel exhaust pollutants found in mines, and modern emission controls. An appendix is included that contains a report describing the capabilities of the Bureau&apos;s diesel emissions research laboratory, two papers describing the effects of engine maintenance or: emissions, a paper describing the monitoring of carbon dioxide in mine air as an indicator of air quality, a glossary, and a list of abbreviations and acronyms.

Jan 1, 1992