Search Documents

By Shenghui Guo, Ying Lei, Wei Li, Jinhui Peng, Libo Zhang, Yu Li

"In this work, the Panzhihua low grade ilmenite and graphite were milled for 1, 2, 4 and 8 h firstly, then the temperature rising behavior of milled sample in microwave field were studied. The average heating rate of samples milled for 1, 2, 4, 8 h were 1.86, 4.08, 2.82, and 2.32 K/s; Before optimize the microwave reduction process, several experiments were conducted in order to confirm the parameters range. After milled for 4 or 8 h and reduced above 930 oC, the Fe metallization are higher than 90%; Then the optimization was investigated by using response surface methodology (RSM), the significance of predict model and each terms were analyzed, and the optimization parameters were given as: milling time is 4 h; reduction temperature is 1001 or 1070oC; the holding time is 37.5 or 26.9 min. Under these conditions, the Fe metallization given by predict model is 91 or 92 %.IntroductionThere is about 9.66 billion tons of Vanadic Titan-magnetite deposits in Panzhihua, China. In this reserve, there is about 8.73×108 t of TiO2, accounting for 90.54% of the Chinese reserves, and 35.17% of the international reserves and ranking first in the world. [1] Titanium mineral deposits are classified into Rock type and Placer type. Rock type is the igneous mineral, which have high content of FeO (Relative to Fe2O3) and gangue. The Panzhihua ilmenite is a typical rock type ilmenite ore. The higher contents of MgO, CaO, SiO2 and the complex mineralogy are making its direct reduction progressively more difficult."

Jan 1, 2011

By Ahmet Haxhiaj, Jaroslaw Drelich

"Both composition and porosity of pellets are the main parameters influencing the reductive melting process in water-jacket furnace during the roasting of sulfide lead concentrate. Roasting in a smelter located in Trepçë is done at about 9000C, for pellets which are composed of PbS, CaCO3, Fe2O3, and SiO2. In order to faciltiate the formation of slag in the reductive melting, the pellets must have the proper content of CaO, SiO2, and FeO, and porosity. The plant’s practice indicates that pellets with porosity of 18% do not melt adequately in the water-jacket furnace. The optimum porosity for the proper melting of pellets needs to be 32-40% and can be achieved when pellets are loaded with more than 10 wt.% CaO. Pellets with less than 10% CaO have a limited network of pores, such that reactive gases cannot reach the entire ore structure. Also, the composition of the pellets must satisfy the ratio of CaO : SiO2 : FeO = 1 : 1.2 : 1.8 to facilitate the formation of slag in the reductive melting process.IntroductionAgglomeration roasting of sulfide lead concentrate is an important phase in the production of lead by reductive melting [1-6]. The reductive melting process is a complex process with contradictory effects of several technological indexes which many times are hard to measure and determine. In this process, loading the water-jacket furnace with pellets of optimized composition and structure can reduce the consumption of coke, and achieve high level of lead recovery. Pellets (agglomerates) should be porous, but at the same time they should have necessary mechanical strength. ‘Self-melting’ ability of pellets is controlled by the types and quantities of fluxes blended into the pellet composition. Three major additives and their role are:"

Jan 1, 2011

By Peter Woodall, Paul Telford, Pengfu Tan

"Arsenic enters the Mount Isa copper circuit in the form of arsenic rich minerals in concentrates from both the Mount Isa and Ernest Henry copper mines. Arsenic is a volatile metal, and will partition in the copper smelter between smelter off gases, slag and anode. Most of the volatile arsenic will report to Isasmelt Electrostatic Precipitator (ESP) or Waste Heat Boiler dusts where it will form a re-circulating load within the smelter. ESP dust is produced at a rate of 15,000 - 20,000 t/y and is currently removed from the precipitator and leached in the new ESP Dust Recovery Plant to separate copper and arsenic from the ESP dust. This paper describes the laboratory test works of ESP dust leaching, neutralisation and cementation processes. The planttrial, commissioning and operation have been presented as well.1. IntroductionThe flue dusts generated in the process of copper smelting contain appreciable amounts of copper and other valuable metals including precious metals. These flue dusts also contain appreciable amounts of arsenic trioxide where arsenic occurs in the ore body. The copper smelters processing concentrates generate residuals, such as ESP dust, containing arsenic trioxide. ESP dust contains impurities such as arsenic and bismuth which are harmful to the copper refining process if they report to anode. These impurities are fumed off in the smelting process and report to the dust as arsenic and bismuth oxides.The content of arsenic in the feed of Mount Isa copper smelter is about 0.1 % to 0.4%. Arsenic is a volatile metal, and will partition in the copper smelter between off gases and anode. Most of the volatile arsenic reports to Electrostatic Precipitator (ESP) and Waste Heat Boiler dusts where it will form a re-circulating load within Mount Isa Copper Smelter. Unless arsenic is bled from the smelter circuit, it will build up to a point where both anode quality and smelter hygiene are adversely impacted."

Jan 1, 2011

By Kumar P. Dharmasena, Haydn N. G. Wadley, Bill W. Choi

"Non-contact eddy current sensing methods have been developed and applied to Cd0.955Zn0.045Te crystal growth to obtain a better understanding of the melt, solid nucleation, and the growth process. The application of this sensor approach relies on a large difference in liquid and solid electrical conductivities near the melting point and requires knowledge of the relationships between the electrical conductivity, melt composition, and temperature. Using a multifrequency encircling eddy current sensor, the electrical conductivities of three different Cd1-xZnxTe (x=0.00, 0.045, and 0.08) alloys were measured as a function of temperature in a laboratory-scale vertical Bridgman furnace. The measured solid and liquid electrical conductivities were then used in electromagnetic finite element models to analyze the multifrequency responses of eddy current sensor designs during the simulated growth of a crystal. These eddy current sensors were fabricated and installed in a vertical Bridgman furnace and used to monitor many Cd0.955Zn0.045 Te growth runs. One sensor was placed in the vicinity of the ampoule tip to detect undercooling/spontaneous nucleation and two other sensors (""absolute"" and ""differential"" designs) placed to monitor the movement/curvature of the liquid-solid interface during crystal growth. The sensor data was used to characterize the initial melt state, detect the onset of nucle-ation, determine the growth velocity, and identify the shape of the interface.IntroductionSingle crystal CdTe and its solid solution Cd1-xZnxTe alloys (0.03<x<0.05) are used as infrared transparent substrates for infrared focal plane array (IRFPA) detectors [1-6] and as solid state y- ray detectors [7-9j. Cd1-xZnxTe substrates are normally ""mined"" from large polycrystalline boules grown by the unseeded directional solidification of Cd1-xZnxTe melts using either a vertical or horizontal Bridgman process [10-14]. The vertical Bridgman method is particularly popular for growing CdTe and its related compounds. In this process, a Cd1-xZnxTe ingot is produced by first melting a charge in the hot zone of the furnace and then vertically translating the furnace (with its associated axial temperature profile) relative to the stationary crucible to cause directional solidification. In spite of many experimental efforts to investigate the relationships between material purity, stoichiometry, the controllable growth parameters (furnace temperature profiles, ampoule geometries/materials, furnace translation rates and starting position) and the resulting material characteristics (grain structure, dislocation densities, IR transmission, macro-segregation etc.), the yield of Cd1-xZnxTe of a quality suitable for large area (e.g. 4 cm x 6 cm) substrates remains low (<10%). Since much of this poor yield is directly associated with the crystal growth process (e.g. melt stoichiometry, solidification velocity, interface shape, temperature gradients, cooling rate, etc.) intensive efforts are under way to improve this technology."

Jan 1, 1997

By S. L. Pohlman

Physical characteristics of possible importance in the acid leaching of Chrysocolla have been evaluated. Surface area studies and pore size distribution indicate: 1) a large surface area (350 m /gm); 2) an average pore size of 13 or 16 Å , depending upon use of the adsorption, or desorption, branch of the Type IV isotherm in the evaluation; ) the presence of a significant fraction of pores of size less than 15 Å determined by the accumulation surface area method. The initial structure is micro- crystalline on the basis of x-ray powder patterns; the silica leach residue is amorphous and has only 24 m2 /gm surface area, and loses integrity when dry. However, readsorption of copper onto the wet leach residue gives a product with integrity and 100 m2 /gm surface area. Visual observation of the leach residues supports evidence of a non-protective diffusion mechanism of leaching which is well correlated by the shrinking core model previously presented.

Jan 1, 1976

By E. W. Lithgow

Commercial volumes of nickeliferous laterite ores overlie part of a 90 km long belt of peridotites in central Dominican Republic. Protores are serpentinized harzburgites and dunites, with lesser serpentinite. The ore mineralogy consists mostly of goethite, serpentine-group minerals, quartz and poorly crystallized, x- ray amorphous materials. Minor constituents are hematite, gibbsite, olivine and enstatite. In the Ore Dressing plant the mine feed is subjected initially to proper sizing and blending to produce a homogenized mix. Subsequent drying and upgrading, by selective crushing and screening of rock fragments through a Barmac circuit, complete preparation of the ore for pyrometallurgical processing.

Jan 1, 1993

By B. R. Davis, Neale R. Neelameggham, R. E. Brown

The element Calcium element has a unique place in the production of etals, intermetallics and other compounds. The unusualness arises from the fact that we have several possible reductants – metallic calcium, calcium carbide, calcium cyanamide and calcium hydride. A review of how metallic calcium is manufactured and utilized is presented. The difficulties involved in producing the metal in large quantities and price implications are noted. . Fundamental thermodynamics of how these act as reductants are shown, along with the historic application of these in metal production during the past century and a half. Alternate applications as to how to control the cost of the reductant is indicated, such as the numerous attempts in making low cost titanium utilizing direct or indirect calcium reductant.

Jan 1, 2014

By I. Gaballah

Cadmium is toxic to plant, animals and humans. The council directive of the European Communities No 8315 13lEEC has fixed an upper limit of 200 ppb for the release of cadmium in industrial effluents. The conventional method of neutralization/prccipitation ( NIP ) is inefficient to reach this limit. The objective of this study is to test the efficiency of the trees modified bark to remove cadmium cations from industrial effluents after the conventional treatment by NIP. Laboratory scale tests with synthetic solutions show that the cadmium removal depends upon pH and initial concentration. About 99.9 %, 99 % and 96 % of the metal are removed from synthetic solutions containing 10, 100 and 1000 ppm respectively. Pilot plant trials ( 1 m3 ) with an industrial effluent bearing about 500 ppb of cadmium lead to the almost complete elimination of the cadmium ( final concentration is lower than the analytical detection limits < 20 ppb ).

Jan 1, 1994

By Björn Saxen

Outotec atmospheric Direct Leaching has so far been implemented for zinc production capacities of around 100,000 t/a. Lately, there has been growing interest for small scale direct leaching plants, producing circa 30,000 t/a of Zn. Such small leaching plants can provide extra front-end capacity in existing roaster-based plants and enable treatment of feed materials not suitable for roasting. In small scale plants the proven OKTOP® 9000 Direct Leaching reactors are not readily applicable, due the large size. For smaller installations a modular approach is proposed providing multiple advantages, such as reducing the construction time and amount of the site work required causing less disturbance to regular plant operation with reduced cost. In this paper, we present advantages that can be achieved by using modular OKTOP®C reactors and discuss also process design when connecting a small scale direct leaching process to an existing zinc plant. Also benefits of direct leaching expansion are presented.

By Bien Ferrer

In most smelting operations, there is a strong incentive to improve safety, reduce downtime and extend the campaigns of furnaces and related equipment. An asset management strategy that is based on information, rather than simple throughput metrics and intuition, can be developed to improve uptime and unlock value currently unrealized at existing smelters. Advances in digital technology, including data analysis, modelling and monitoring for hot pyro-metallurgical vessels, make it possible to assess the current condition of an asset, as well as to make more informed projections about its future condition, using on-line and historical data. This would allow practices around asset management to be more proactive and less reactive, with the end-result of optimized uptime. ‘Digital Asset Management’ describes a concept in which digital technology is used to support an asset management strategy and accelerate decision-making by providing information on what, why and how an asset should be designed, operated or maintained. With the overall goals of effective resource utilization, optimized operations, capital efficiency and social acceptance, Smelter 4.0 is a program of holistic improvement and is underpinned by the effective use of data to drive decisions. This paper focuses on Asset Reliability, which is one of the improvement pillars of Smelter 4.0, and introduces a methodology that is aimed at closing the gap between recorded data and evidence-based decision-making through Digital Asset Management.

By Peng Lv, Shiqian Liu, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

The treatment process of a low-grade refractory gold ore containing sulfide minerals and carbonaceous matters was studied in this work. The gold extraction of this ore by all-sliming cyanidation was only 11.75%. Hence, a pretreatment was necessary. In this paper, a flotation-preoxidation-cyanide leaching process was developed. The concentrate from the flotation procedure was processed using different preoxidation methods. A concentrate containing 34.08g/t of gold with the gold recovery ratio of 81.20% was obtained by flotation. After roasting, microwave heating or alkaline pressure oxidation, the gold cyanidation ratio reached 82.37%, 81.26% and 71.09% respectively. Roasting was an effective, reliable and mature technique to oxidize sulfide minerals and carbonaceous matters. Roasting and microwave heating both produced dangerous environmental pollutants while alkaline pressure oxidation was eco-friendly.

Jan 1, 2015

By Daniel Adolfsson, Ryan Robinson, Fenwei Su, Jelena Blagojevic

"Cold bonded briquetting of steel plant by-products has proven to be a viable recycling alternative concerning technology, economy and environment in both the traditional blast furnace route and the direct reduction process. A critical parameter in cold bonded briquettes is the type and amount of binder used during production. The binder material must meet certain quality requirements concerning low and high temperature strength, chemistry and economy. Currently, SSAB Tunnplåt uses ordinary Portland cement (OPC) as binder in their cold bonded briquettes. In order to improve binder quality and possibly decrease OPC dependency, a binder feasibility study has been conducted concerning an internal by-product, ladle slag, as a supplement and/or partial substitute for OPC. Several characterization techniques have been used to study the behaviour of ladle slag, these include: XRD, XRF, SEM, glass content analysis, calorimetric analysis, particle size distribution and thermochemical stability considerations concerning the CaO-Al2O3-SiO2 system.IntroductionRecently, a project was initiated at SSAB Tunnplåt AB, in Sweden, which aimed at reducing the amount of ordinary Portland cement (OPC) as hydraulic binder in cold bonded briquettes by partly replacing it with ladle slag. OPC is traditionally used within civil engineering, and widely accepted as a hydraulic binder in a number of different applications. OPC consists of four major crystalline phases, i.e. C3S, C2S, C3A and C4AF. Tricalcium aluminate as well as the ferrite phase in OPC reacts very quickly with water, for this reason gypsum is added to the clinker in order to retard these reactions. The fact that gypsum is present in the system limits the recycling of briquettes to the BOF, since the presence of gypsum during steelmaking results in a significant amount of sulphur emissions. The latter along with the expense that follows, makes it worthwhile to consider alternatives for OPC as binder in cold bonded briquettes."

Jan 1, 2008

By Z. Zhang, R. G. Reddy

The viscosities of industrial lead slags with various compositions were measured as a function of temperature. It was found that viscosities of lead slags decreased with increasing temperature, and the plots of ln(11) vs. 104tr followed a linear relation over the reported ranges of temperature. Using the data of this study and available other related data from the literature, a viscosity expression was developed as a function of composition and temperature. The calculated results using this viscosity expression are in good agreement with the measured data. The composition dependency of viscosity of lead slags is discussed.

Jan 1, 2000

By Zhaohui Xie, Bin Xu, Qian Li, Yongbin Yang, Tao Jiang

A high carbon low-grade gold ore, in which gold mainly occurs in carbonaceous matters, is a typical refractory gold ore whose conventional cyanide leaching extraction is only 12.9 %. In this paper, by the process of flotation-roasting-leaching, gold was effectively enriched and extracted. The flotation results showed that the enrichment ratio of gold was relevant to that of carbon, indicating that gold occurred in close association with carbon. A concentrate containing gold 7.26 g/t and carbon 12.37 % was obtained, with gold recovery 83.10 % and carbon recovery 90.24 %. Subsequently, the roasting of flotation concentrate favorably made the removal rates of carbon and sulfur reach 99.81% and 98.79%, respectively. After roasting, the gold in the roasted product was further enriched to 29.70 g/t and the optimal gold cyanide leaching extraction reached 93.66%.

Jan 1, 2015

By Cynthia Belt

"Before energy can be saved in the materials industry, the process must be understood. At the same time, baby boomers are starting to retire. New people are entering the field without experience and training especially in methods to save energy. Various classroom courses, seminars, books, software, and websites are available for the professional to better understand the industry with the ultimate goal to reduce energy use. This paper is a review of what is currently available with some comments on potential needs.IntroductionEnergy use is high within the materials industry. For the United States, the primary metal industry uses 8% of all energy used in manufacturing (Figure 1 )1 or 1, 736 trillion BTUs per year. Sadly, while energy use is high, energy management is not universal within the industry. Counting both internal programs and external such as the utility supplier, equipment manufacturers, federal and state programs, only 66% of primary metals companies participate in an energy management activity1.For the materials field, process heating is the majority of the energy use in a plant2. Understanding and optimizing process heating is a critical need for materials energy professionals. Surprisingly, process heating is not necessarily the work addressed within an energy program. The U.S. 2006 Manufacturing Energy Consumption Survey (see Table 1) found more primary metal companies addressing lighting with 31 % participation versus 15% with process heating work even though energy used in lighting tends to be a minor (in the range ofl-3% ofa typical plant's energy use)."

Jan 1, 2013

By A. Bilodeau

A new hydrometallurgical process for the production of refined gold and the recovery of palladium and platinum from silver anode slimes has recently been developed and installed at the, CCR Division of Noranda Inc. The process, which facilitates the production of gold of >99.99% purity in the face of increasing palladium receipts comprises; leaching silver anode slimes with hydrochloric acid and hydrogen peroxide at 95°C to solubilize gold, palladium, platinum and base metals while simultaneously rejecting silver as insoluble silver chloride; precipitating gold from the leach solu¬tion with sulphur dioxide gas in two stages to produce a first-stage high purity gold product and a second stage impure gold which is recycled to the leach; washing, melting and casting of the pure gold; precipitation of a palladium-platinum concentrate from the gold-free solution by reduction with sodium formate at pH 4 and 95°C; and neutralization of the palladium precipitation effluent to pH 10 with lime. The results of laboratory and pilot plant studies leading to the adop¬tion of this process are discussed, and data are presented for each of the unit operations. Details of the engineering of the commercial plant are given, and plant start-up experience is described.

Jan 1, 1987

By Hiromichi Ohta

Precise thermal properties of molten materials are essentially required for analyzing the metal production process. These properties are also important as a clue to consider the dynamic structure of liquid materials. However, it is difficult to obtain the precise thermal diffusivity values of molten oxides at high temperature because of the experimental uncertainties arising from the bubble formation or the severe separation of radiative and conductive heat components. Recently a novel laser flash method has also developed for measuring thermal diffusivity of molten oxides at high temperature. In this new technique, the sample is melted in a metal crucible and heated to the desired temperature. A single laser pulse is flashed on the bottom of the metal crucible and the infrared ray irradiated from the same bottom surface is measured for obtaining the temperature decay, from which the thermal diffusivity of the liquid sample can be estimated. The usefulness and validity of this new laser flash technique have been confirmed by obtaining the thermal diffusivity values of silicate melts in the wide temperature range between 773 and 1673 K.

Jan 1, 2003

By M. C. Ruiz

In the present study, the size distribution, Fo(v), of organic drops produced in a continuous-mixing vessel has been determined experimentally for various conditions. The organic phase used was a 1: 1 mixture of a salicylaldoxime (LIX 860N-IC) and a ketoxime (LIX 64-IC) in an aliphatic diluent (Escaid 103). The aqueous phase was a copper sulfate solution. The results indicated that an increase in stirring speed, extractant concentration, and pH produced smaller drops. The effect of the stirring speed was the most significant, decreasing the average volume of drops by 57 % for a change from 300 to 400 rpm. On the contrary, an increase in the dispersed phase fraction, copper sulfate concentration, and retention time produced larger drops. Changes in temperature from 23 to 30°C did not affect significantly the drop sizes. In all cases, the experimental drop size distributions could be accurately represented by a lognormal distribution.

Jan 1, 2001

By H. H. Kellogg

The Process Fuel Equivalent (PFE) for nine different flowsheets for production of anode copper from sulfide concentrates has been evaluated and compared for a set of uniform conditions and a "standard" concentrate analysis. The processes considered are: reverberatory smelting, (wet-charge and hot-calcine charge), electric furnace smelting, Outokumpu flash smelting (2 versions), mom flash smelting, Noranda Continuous Process (2 versions), and the Mitsubishi Continuous Process. The energy required for the numerous processes auxiliary to the principal smelting processes-¬roasting, drying, air compression, gas handling, dust collection, slag cleaning, acid manufacture, etc.--are separately evaluated and incor¬porated into the process comparisons. The factors in process design that lead to important energy savings are: use of fuel rather than electric energy; use of oil or coal rather than natural gas; maximum use of oxygen enrichment of the process air; drying of charge before smelting, or, even better, drying and preheating of charge by partial roasting in a fluid-bed; recovery of waste heat from all major hot process gases.

Jan 1, 1976

By Huimin Lu, Qiang Li, Jingbo Xu

"The smelting reduction of V-Ti bearing beach placer by combined rotary hearth furnace and direct current arc furnace was studied in laboratory. It takes the aid of back propagation (BP) neural network theory to build the nonlinear mapping relations between the crucial process variables such as content of carbon, temperature and time and the degree of reduction. Then by the integrating BP neural network and genetic algorithm (GA), the optimized process parameters for the high degree of reduction were searched. The comparisons between experiment results and neural network simulation results show that GA-based on BP method can predict the degree of reduction with higher prediction accuracy. Calculations show that the integrated energy consumption of new technology is 580kgce/tHM, less than the current existing blast furnace.IntroductionThese V-Ti bearing beach placers (VTBBP) are secondary Fe-rich minerals formed by rivers, ocean waves, ocean tides and ocean currents on beach zones, their useful minerals are V-Ti magnetite ores. On Asia Pacific zone, such as Japan, China, Philippines, Indonesia, Australia and New Zealand, the VTBBP have large reserves and wide distribution. But so far, the VTBBP are not still comprehensively utilized. Therefore, in this paper, a combined rotary hearth furnace technology and arc furnace smelting method is studied for comprehensive utilization of the VTBBP. The main objective of this paper is to find optimum operation conditions for the production ofV-bearing iron and titania-rich slag from the VTBBP by means of the laboratory testing.Recently, neural network (NN) expected to be able to provide an effective tool because of its advantages, which describe nonlinear mapping relations. With the characteristics of strong selflearning, self-organization, robust error toleration and accurate nonlinear relation approximation, artificial neural network can be applied to nonlinear process modeling based on sufficient training. Back-propagation (BP) training algorithm is probably the frequently used one in practical application. Genetic algorithm has parallel search strategy and global optimization characteristics, which makes the trained neural network being higher classification accuracy and faster convergence speed. So it is necessary to combine neural network and genetic algorithm. The nonlinear relationship between input and output presented by NN and the global optimal function of GA are abroad applied in the engineering and scientific research [1, 2]. So these methods supply an efficient path to solve the above problems. At present, it is common to study the optimization of process parameters by orthogonal experimental design, the method combining neural network and genetic algorithm is a novel and better method than orthogonal experimental design. Tills study organized the above advantages to optimize the process parameters for comprehensive utilization of the VTBBP."

Jan 1, 2012