Search Documents

By R. Craig McClung

Contrary to other sulfide minerals, where recovery is principally liberation controlled, the recovery of molybdenite is more complex. It is this complexity that initiated a geometallurgical investigation of molybdenites from Bingham Canyon. The aim of this investigation was to determine the effect mineralogy and/or mineralogical attributes have on recovery. All samples were analyzed using normal mineralogical techniques. The results reveal the presence of two distinctly different types of molybdenite. These have been identified as the two polytypes of molybdenite: i.e. hexagonal (2H); and rhombohedral (3R). The 2H-polytype occurs as textbook-shaped particles in quartz-molybdenite veins that are located in the current pit bottom. The 3R-polytype occurs as disseminated, “ball”-shaped particles with a dull or frosted appearance and are concentrated along the margins of the current pit. Concerning their metallurgical behavior, each type exhibits unique metallurgical properties that are consistent with those reported in the published literature. The 2H-polytype is easily ground and kinetically “faster” floating with surface attributes that are amenable to higher rates of recovery. This results in the production of a high quality concentrate under normal operating conditions. The 3R-polytype, by comparison, is difficult to grind and kinetically “slower” floating with surface attributes that are less amenable to recovery. Therefore, in deposits with higher concentrations of the 3R-polytype, modifications to the normal operating parameters may be necessary to improve recovery. This investigation highlights the necessity for understanding the mineralogical characteristics of any economic mineral(s), as these will have a direct impact on recovery.

By Robert D. Pehlke

"Current continuous casting processes are going through a rapid evolution of advances and new developments. At the same time, intense efforts are being directed to the development of radical new technologies such as continuous casting of thin slabs and strip steel.Traditionally, the casting processes for steel have been anticipated by the development and implementation of processes in the non-ferrous industry. This trend is reviewed and what it may portend for steel is described.IntroductionThe continuous casting of steel has been a widely adopted process in the production of steel. The concepts for this processing go back into the early and mid 1800's; however, commerical development was delayed for a variety of reasons until the mid twentieth century.Beginning in the early 1960's, adoption of continuous casting was initiated and continues at this point in time to be accelerated. In Japan, more than 90% of the steel produced is continuously cast (1). More than 50% of the steel produced in the United States is continuously cast and this fraction continues to rise (2). Numerous examples can be cited of installations costing well over $200,000,000 which have provided a payoff in less than a year and a half. As this process has continued to be applied and its technology to increase, computer control systems have been installed. In particular, in the larger plants producing slabs, sophisticated computer systems involving the integration and networking of mini-computers, micro-computers, and mainframe including back-up systems at all levels are being utilized. Pehlke (3), and Harabuchi and Pehlke (4) have described the structure of these systems."

Jan 1, 1988

By Wenjun Duan, Kun Wang, Qingbo Yu, Qin Qin

"A novel oxygen production technology noted chemical looping air separation (CLAS) was introduced and properties of Cu-based oxygen carriers used were investigated. The oxygen carriers were prepared by mechanical mixing. Al2O3, Fe2O3, ZrO2, TiO2 and SiO2 were used as binders during the preparation. XRD patterns show that spine! oxides are formed using Al2O3 and Fe2O3 as binders. Phases of CuO and binders keep stable using ZrO2, TiO2 and SiO2 as binders. BET values of oxygen carriers increase in the order of ZrO2>TiO2>SiO2>Fe2O3>Al2O3. The effects of temperatures, binders, particle sizes and flow rates on reduction/oxidation reaction rates were studied in TG experiments. The reduction reaction rate increases in the order of ZrO2>TiO2>SiO2. The effect of binders on the reactivity of oxidation is not obvious. The reduction and oxidation reaction rates both have the tendencies of increasing with the temperature increasing and with gas flow decreasing. However, the effects of gas flow and particle size are little.IntroductionChemical looping air separation (CLAS) is a novel oxygen production technology. The oxygen carriers used in CLAS release oxygen in reduction reactor and regenerate in the oxidation reactor. Selecting suitable oxygen carriers is the key for CLAS. Oxides of CuO, Mn2O3, Co3O4, Pb3O4, CrO2, SrO2, PdO2 and CeO2 have the property of releasing oxygen at suitable temperature and oxygen partial pressure [1]. Among these oxides, CuO, Mn2O3, Co3O4 are the most common compositions used to prepared oxygen carriers for chemical looping combustion (CLC) or chemical looping with oxygen uncoupling (CLOU) [2-5]. Moreover, thermodynamic calculations and preliminary experiments were carried out on oxides of Cu (CuO/Cu2O), Mn (Mn2O3/Mn3O4) and Co (Co3OJCoO) by Moghtaderi to ascertain their feasibility for CLAS process [6]. CuO has the highest oxygen transport capacity (0.1 g 02/g CuO compared to 0.03 g 02/g Mn2O3 and 0.06 g 02/g Co3O4). However, agglomeration is the biggest issue for copper oxides used at high temperature because of its low melting point (l 450°C for CuO, 1235°C for Cu2O and 1075°C for the mixture of CuO and Cu2O) [7]. In order to improve the capability of anti-sintering and stability ofCuO, binders (ZrO2, MgAl2O4, TiO2, SiO2, Fe2O3, Al2O3, cement) are added during the preparation of Cu-based oxygen carriers [8]. In this paper, the Cu-based oxygen carriers were prepared by mechanical mixing method. TiO2, Al2O3, Fe2O3, ZrO2 and SiO2 were selected as binder. XRD, BET and SEM were used to analyze the phase, surface area and surface morphology of oxygen carrier prepared. The reactivity of oxygen reduction and oxidation of oxygen carriers prepared were investigated in STA409PC thermal analyzer."

Jan 1, 2014

By Regina Krachler, Herbert Ipser

"The principles of the derivation of statistical-thermodynamic models to interpret the compositional variation of thermodynamic properties in non-stoichiometric intermetallic compounds are discussed. Two types of models are distinguished: the Bragg-Williams type, where the total energy of the crystal is taken as the sum of the interaction energies of all nearest-neighbor pairs of atoms, and the Wagner-Schottky type, where the internal energy, the volume, and the vibrational entropy of the crystal are assumed to be linear functions of the numbers of atoms or vacancies on the different sublattices.A Wagner-Schottky type model is used for the description of two examples with different crystal structures:For B'-FeAl (with B2-structure) defect concentrations and their variation with composition are derived from the results of measurements of the aluminum vapor pressure; the resulting values are compared with results of other independent experimental methods.For Rh3~ (with an NiAs-derivative structure) the defect mechanism responsible for nonstoichiometry is worked out by application of a theoretical model to the results of tellurium vapor pressure measurements. In addition it is shown that the shape of the activity curve indicates a certain sequence of superstructures.In principle, there are no limitations to the application of statistical thermodynamics to experimental thermodynamic data as long as these are available with sufficient accuracy, and as long as it is ensured that the distribution of the point defects is truly random, i.e. that there are no aggregates of defects."

Jan 1, 1996

By Sang Han Son

The vapor pressures of FeCL2 and ZnCL2 in the FeCL2?ZnCL2 system were measured by the transpiration method at 873K and 9I7K, The vapor pressure data were interpreted to indicate the formation of complex ions in the FeCL2?ZnCL2 melts, It is presumed that the complex molecule FeZnCl4 as well as FeCL2 and ZnCL2 exists in the vapors in equilibrium with molten FeCL2-ZnCL2 mixtures, The activities in the FeCL2-ZnCL2 system are shown a negative deviation from Raoult's law. These results suggest the formation of complex ions such as ZnCL14 in molten FeCI2?ZnCL2 mixtures.

Jan 1, 2003

By Jürgen Antrekowitsch, Thomas Griessacher

"Heavy metal containing residues are typically hazardous wastes because on the one hand, a deposition gets more and more complicated and on the other hand, the large amounts of metals like Zn, Cu, Fe and Pb represent a significant value. Thus, a post-treatment of these materials with the recovery/recycling of the metals and stabilization of the waste is not only ecological but often also economical. The therefore typically applied recycling processes utilize pyrometallurgical steps, where carbon or carbon monoxide from fossil coal and coke is used as a reducing agent, which results in large amounts of CO2 emissions. An alternative option is the application of a hydrogen-rich gas emitted in biomass utilization processes as a carbon-neutral reducing agent. Investigations in a retort process which were done at different temperatures and times showed excellent results concerning the achievable reduction rates and final contents of the heavy metals for various residues.IntroductionNowadays heavy metal containing residues like electric arc furnace dust (EAFD), dust from cupola furnaces, waelz slag, etc. are declared as hazardous wastes in a growing number of countries due to the leachability of the heavy metals in these residues. For that reason it is no longer possible to landfill these materials or use them for road construction or disposal works. Some land filling activities, carried out until now, have only been realizable because of some process modifications or cost intensive post-treatment steps of these residues. But the disposal capacities for such materials are decreasing, therefore increasing the prices. The second point for the growing disposal limitations is the stringent environmental legislations and regulations, which restrict the number and amounts of materials which can be dumped [1 – 5].From the other point of view these heavy metal containing residues usually have high contents of zinc, lead, iron, etc., which represent a significant value and therefore a big potential to recover these metals. This is why in recent years the number of recycling processes and the amount of recycled heavy metal containing residues have continuously increased. These recycling processes have the target to recover the valuable metals from the residual materials in the form of a saleable product as well as the stabilization of the slag produced in these processes [5, 6]."

Jan 1, 2011

By John W. Ahlrichs

Microscope, electron microprobe and x-ray diffraction have been used to provide quantitative evaluation of products from the mill, smelter, refinery and other metallurgical processes. Phase compositions and their quantities are necessary for an adequate understanding of the various products obtained throughout an operation and in laboratory testing. By careful evaluation, important information can be gained in improving recoveries and increasing grades at various stages of processing. Four case histories are discussed in this paper. Quantitative microscopic counting techniques are applied to mill products to determine degrees of locking and liberation of the economic minerals. Rapid, but accurate evaluation aids the metallurgist to develop or improve the grinding and flotation circuits. In the smelter, the identification and quantification of the phases are important for predicting reaction mechanisms and kinetic trends. Mineralogic techniques have been applied to conventional smelter products, and to those obtained in laboratory tests for newly developed innovations to smelting. Small, but important, values of gold occurrences in ore are difficult to determine. Evaluation of gold usually requires special separations into various mineral concentrates, followed by assays and mineralogic determinations of the products. Numerous occurrences of solid solution constituents can be treated as by-products, but often they are deleterious to metallurgical treatment. Most solid solution problems can be unraveled by the mineralogist's tools.

Jan 1, 1981

By D. V. Hughes, J. R. Nyberg

"Since 1985, a comprehensive automation system has been installed at the Outokumpu Oy Zinc Plant, Kokkola, Finland. In leaching and solution purification special sample handling equipment, on-line analyzers and instruments, and a computer-based control system with duplicated supervisory stations have been installed. The system has enabled closer control of the process and more efficient use of labor. Since its installation recovery of zinc has improved, and use of zinc dust, steam, and water have decreased. The system has performed reliably. It includes optimizing programs and process study tools, which facilitate improving process performance. An expert system has been built-up to prompt process personnel to take appropriate action on the basis of process data. In electrolysis a similar system, based on extensive monitoring of the process and of production of zinc cathodes, is used to maximize- current efficiency by maintaining optimum conditions in the process. It is planned that in the future the control systems will be integrated and extended to cover the roasting plant and effluent control.IntroductionThe Zinc PlantThe Zinc Plant of Outokumpu Oy Metallurgical Division at Kokkola, on the West Coast of Finland, has grown from a 90,000 t/a plant founded in 1969 to become, with its present capacity of 170,000 t/a, one of the world's ten largest zinc plants. Especially since the completion in 1988 of a thorough modernization programme, it is also among the world's most modern.The Kokkola plant takes its raw materials from Outokumpu's own mines, Vihanti and Pyhasalmi in Finland, and Tara in Ireland, and from outside sources. Concentrates are roasted in two Lurgi fluid-bed furnaces, and the calcine is leached and iron removed by the Conversion process. Following this copper, cobalt, and cadmium are removed, and zinc is refined by electrowinning. The leaching and purification, and the cell-house are automated under computer-based control, and anode and cathode handling in the cell-house are mechanized and fully automatic."

Jan 1, 1989

By M. Elbert Nigri

Radioactive wastewaters from nuclear source of electrical energy production need to be treated and disposed of properly. Sr, Ca, Mg and Ba are common elements in this effluent, which can cause incrustation in process equipments and being unsafe to human health (90Sr). Fixation of CO2 can be applied to remove the ions mentioned before and to provide a solution where CO2 is sequestered and the deleterious elements precipitated, becoming one of the possible steps to reuse the water into the process. Moreover, removal of several metals from distinct wastewater has been evaluated using bone char through adsorption. The chemical similarity between calcium and strontium makes the exchange of these two metals favorable in the hydroxyapatite structure contained in bone char. This paper evaluated the combined action of precipitation and adsorption process with injection of CO2 and bone char addition in simulated nuclear wastewater. Removal levels of 89.0% (Sr) and 83.3% (Ca) were obtained in the combined process. The presence of bone char as seed increased the precipitation kinetics, allowing a Sr removal of 85.2% in five minutes, higher than 75.3% obtained in absence of seeds. However, removal of 91.6% (Sr) and 89.8% (Ca) were obtained in absence of seeds at 24 h. Analysis of solids have evidenced that CO2 was consumed to precipitate the metals as carbonates, since the hydroxides are formed at higher pH’s.

By Lawrence L. Brown

As part of the Federal effort to help maintain an adequate supply of fertilizer materials, the Bureau of Mines conducted research to characterize complex low-grade Michigan phosphate materials and to devise methods for recovering fertilizer-grade phosphate concentrates. The rock is from middle Precambrian sedimentary formations in the Marquette Range located in the central part of the Upper Peninsula of Michigan. Occurrence of phosphate-bearing sediments in Precambrian rocks is rare. This deposit, containing 12 to 15 pct P2O5 is believed to be the richest Precambrian phosphate deposit in the United States. Petrographic examination showed that the conglomeritic rock contains crystalline apatite both in "black pebbles" and in quartz matrix. Attrition scrubbing and sizing tests showed that there is no tendency for phosphate to concentrate in any of the sized fractions. In beneficiation tests, which included grinding to minus 325 mesh followed by phosphate mineral flotation using a fatty acid-fuel oil collector, a phosphate concentrate was obtained that had a grade of 30 pet P2O5 and a P2O5 recovery of 72 pct. This concentrate should be suitable for fertilizer manufacture.

Jan 1, 1982

By Alice Barreto Bevitori, Felipe Perissé Duarte Lopes, Denise Cristina Oliveira Nascimento, Sergio Neves Monteiro, Isabela Leão Amaral da Silva

"The piassava fiber is one of the most rigid natural lignocellulosic fibers, which has since the last decade been investigated as possible reinforcement for polymeric composites. In the present work, the tensile properties of polyester composites reinforced with piassava fibers with thinner diameters were investigated. Composites with volume fractions up to 30% of continuous and aligned piassava fibers were tensile tested at room temperature to evaluate the ultimate strength, elastic modulus and total strain. For each volume fraction, individually separated fibers with the smaller diameters were tested. The results indicated that the tensile properties tend to improve with increasing volume fraction of the thinner piassava fibers. The role played by the fiber/matrix interaction was analyzed by scanning electron microscopy.IntroductionA significant change in the transportation sectors mainly the aerospace and automotive, occurred last century with the introduction of stronger and lighter materials. The most relevant example was the polymer composite reinforced with synthetic fiber. They are nowadays replacing conventional materials such as the aluminum alloys in airplane body owing to superior specific strength. in recent years, however, environmental problems in a global scale are imposing a reversion in the use of synthetic fiber specially the glass fiber. In spite of its higher specific strength, this fiber and its polymer composites can neither be recycled nor incinerated in a thermal plant to generate electricity [1]. Moreover, the fabrication, processing and transportation of a glass fiber composite are associated with C02emission, the major responsible for global warming [2].A possible substitute for glass fiber without the above-mentioned environmental problems, could be a natural fiber. In fact, natural fibers obtained from cellulose-rich plants, also called lignocellulosic fiber, are already being used in several engineering fields, particularly the automobile industry [3-6]. Figure 1 illustrates an automobile and its many components made of lignocellulosic fiber composite [7]."

Jan 1, 2011

By Allan MacRae

Freeport-McMoRan Inc. operates an ISASMELTTM furnace for the smelting of copper concentrate at the Miami Smelter in Claypool, Arizona. In May 2017, the furnace was restarted after incorporating newly designed copper cooling elements from just above the tap hole to the underside of the roof. The objective of the improved cooling design was to extend campaign life by eliminating existing failure mechanisms with the wall refractory. In addition to upgraded bathline coolers and complete coverage of the gas offtake transition, or ‘kettle’, with plate coolers, a novel arrangement of coolers was installed in the remaining freeboard area. The shell required significant cutting and re-stiffening, as well as extensive modification of the cooling water piping. Based on performance observed to date, it is expected that smelter throughput will be increased due to extended ISASMELTTM refractory campaign life.

By Leonard Harris, Rosa H. Harris

"It is becoming increasingly obvious to mining and exploration companies, when operating overseas, that their activities should not conflict with the interests of the surrounding communities. The world's largest gold heap leach operation, Minera Yanacocha has installed community assistance programs in Peru concerned with health, education, electrification, agricultural assistance and road improvements. The programs are conducted with joint venture partners consisting of the company, the community people, the contractors and suppliers, government and non government organizations and a ladies association composed of the employees' wives and female staff.IntroductionThe l 990's is the decade highlighted by enormous investments in mineral exploration and mining projects in the developing world. Figure 1 illustrates the distribution of exploration spending by mining companies in 1995."

Jan 1, 1997

By Eleazar Salinas R., Miguel Perez L., J. Cesar Juarez T., Martin Reyes P., Eduardo Cerecedo S., Isauro Rivera L., Francisco Patino C., Juan Hernández A.

"A complete characterization of burrows from Mining district of Pachuca - Real del Monte, in Hidalgo state Mexico, was done. These kind of residues had not been formally characterized, founding an average chemical composition of 70.43 % wt. of Si02, 7.032 % wt. of Ah03, 2.69 % wt. of Fe20 3, 0.70 % wt. of Mn, 3.98 % wt. ofK20, 3.34 % wt. of CaO, 2.50 % wt. ofNa20, 1.01 % wt. of MgO, 0.26 % wt. of Ti02, 0.04 % wt. of Zn, 0.026 % wt. of Pb, 56 g/ton of Ag and 0.6 g/ton of Au; In the same way, the residues present as majority mineralogical phases the following: Quartz, Berlinite, Orthoclase, Feldspar, Anorthoclase and Calcite. By the other hand, joint with the big volume that present these residues and the chemical and mineralogical characteristics, these materials or sub - products can be used for production of ceramics, into mixes forming some materials for architecture (bricks, blocks, and tiles), refractory bricks, in the production of cement and to get some metallic values such as gold and silver involved in these residues.IntroductionActually the mining residues in Hidalgo State, Mexico are the result of more tan 500 years of mining, leading so a great volume of deposits, which we can classify in different types, among the most communes we have: Acid Mining Waters, Waters of solid transport and elements in the form of radicals, deposits of abandoned minerals without processing, and mining wastes of processed minerals known as burrows or dumps, being these the most abundant in the Hidalgo State [1-4].Form the metallurgical point of view, it is known that a characterization study if fundamental to find the viability of reuse of these kind of residues, leading so an additional use and the opportunity of get an alternative use into several industrial processes, due to its contents of oxides of silicon, iron, aluminum, calcium, sodium and potassium, principally, besides of its mineralogy and distribution of chemical elements into its primary and secondary phases [ 1-2, 5- 6]."

Jan 1, 2011

By Pengfu Tan

A thermo-chemical model of the copper P-S converter and a viscosity model for the converter slag have been developed to predict the behavior of magnetite in the converter slag, amounts of slag and matte, compositions of slag and matte, volume of the bath, bath temperature, slag blow endpoint determination, SEMTECH OPC signals, and the viscosity of converter slags. The predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by the industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. The effect of oxygen potential, SiO2/Fe in slag, detection of slag blow endpoint, and temperature on Fe3O4 content in converter slag, slag viscosity, liquidus temperature of converter slag and skimming operation has been modeled and discussed as well. Some applications of the industrial operations have been presented.

Jan 1, 2009

By F. Kongoli

Viscosity is an important parameter of copper smelting and converting processes. It affects the settling of matte or metal droplets in the slag, distribution of elements etc. Despite this importance, confusion exists on the viscosity of copper smelting slags as a result of disagreements found among the measured viscosity data of several authors especially in the slags of high ferric iron content and close to magnetite precipitation. In this work a critical review of the existing data on the viscosity of copper smelting slags has been first carried out and the effect of oxygen potential on the viscosity of copper smelting slags has been clarified through a coupled quantification of viscosity and liquidus temperature. The confusion in the literature has been clarified and the importance of the relation between the viscosity and the liquidus temperature is discussed.

Jan 1, 2003

By A. Kontopoulos

Refractory sulfide gold ores or concentrates require an oxidation pretreatment step to yield the contained gold amenable to the subsequent leaching step. The process options for oxidation pretreatment can be broadly classified as follows: roasting, high or low pressure oxidation bacterial oxidation, chemical oxidation, each with a number of alternative suboptions. Roasting and high pressure oxidation are being applied on an industrial scale; the stage of development of the other options range from preliminary laboratory to advanced pilot plant- In this paper, the major technical, environmental and economic aspects of the above processes are being discussed. Future industrial trends will also be considered. Particular emphasis will be placed on the treatment of arsenical ores and concentrates, where safe plant operation as well as, handling and disposal of the arsenic containing products and/or effluents 'and residues is of paramount importance.

Jan 1, 1990

By G. Mark Aylmore

Various processes have been developed using a combination of elevated temperature and chemical treatment processing to recover Li from silicate minerals. To facilitate further process development, a comprehensive understanding of the deportment of Li and associated minerals in ore bodies is essential to allow the industry to predict the response of ore reserves to metallurgical treatment options. This paper describes results from the integrated use of the John de Laeter Centre’s state of the art analytical and mass spectrometry techniques to characterise a selection of Li bearing ore bodies and determine their amenability to potential processing options for the extraction of Li. The mineralogy, mineral associations, and liberation characteristics of ore-bearing and gangue minerals were characterised using a combination of the TIMA and XRPD studies. The Li content and distribution within minerals were defined using LA-ICPMS and field emission scanning electron microscopy techniques (EBSD, ToF-SIMS) and atomic probe microscopy.

By Sebastiaan Peelman

NdFeB permanent magnets are the best available magnets used in many technology applications. However, at their end-of-life (EoL) most of magnets and the contained REEs are lost during the recycling of the bulk metals. The REEs are classified as the most critical raw materials in the European Union, and recycling of REEs from EoL products will reduce their criticality and contribute to the sustainability of REE. Various technological routes have been reported, but most of the methods are effective for highly concentrated magnets or magnet scrap, which is greatly dependent on expensive pre-dismantling processes. This paper presents various innovative metallurgical solutions to the effective REE recovery from current industrial practice for WEEE recycling, including the ferrous scrap from WEEE shredder products and shredder residues from computer hard disk drives. Both hydrometallurgical and combined hydro- and pyrometallurgical REE recovery routes are developed after demagnetization and physical upgrading.

By Ikuhiro Sumi

A new steelmaking process, in which manganese ore was intentionally reduced, was developed to achieve a higher manganese Yield using a combined blowing converter. In this study, manganese behavior was discussed through the introduction of a model. Apparent reduction rates of manganese were calculated by the two terms that were determined experimentally, with SOkg and 2S0ton combined blowing converters. The model calculated manganese changes during the operation. We applied the model to the actual operation and found that manganese behavior was predicted fairly well by this model.

Jan 1, 1996