Search Documents

By Takashi Nagai, Hideaki Sasaki, Masafumi Maeda

"The production of solar cells is increasing dramatically and the shortage of polycrystalline silicon for these cells has become a serious problem, making development of a low-cost production process for solar grade silicon essential. An electron beam melting technique is known to be effective for the removal of phosphorus from molten silicon. Although the phosphorus is removed by preferential evaporation in this process, the rate of removal is not sufficient, and its improvement requires thermodynamic information on phosphorus in the molten silicon. In this research, the vapor pressure of phosphorus in equilibrium with a siliconphosphorus alloy was measured by double Knudsen cell mass spectrometry with a system blowing gas into the Knudsen cell. The activity of phosphorus in silicon, the Gibbs energy change of the dissolution of phosphorus in silicon, and other factors were estimated from the results. Using these data, we provided guidelines on how this process can be improved.IntroductionSolar energy is in great demand since it is inexhaustible and cleaner than that from conventional energy resources. Silicon is the material most widely used to convert solar energy into electricity. Figure 1 shows the recent production of solar cells. High purity silicon for solar cells, namely solar grade silicon (SOG-Si), has been commercially supplied mainly from off-grade high purity silicon in the semiconductor industry. However, production of solar cells has increased rapidly in recent years, and the shortage of SOG-Si has become a serious problem, so that a new processes which can produce SOG-Si economically are required.Directional solidification was applied to remove transition metal elements such as Fe or Ti by segregating them from the remaining melt. However, such solidification is useless for phosphorus because the segregation coefficient of phosphorus is nearly unity. Numerous approaches have been made in an attempt to produce a resource of low cost SOG-Si from metallurgical-grade silicon (MG-Si). [1,2]"

Jan 1, 2012

By Erich Hovestädt, Hans-Jürgen Odenthal, Christian Wuppermann, Herbert Pfeifer, Antje Rückert

"During the argon oxygen decarburization (AOD) process high-chromium steel melts are decarburized by oxygen and inert gas injection through sidewall nozzles and a top-lance. Due to the large amount of the injected processing gas, low frequency oscillations of the vessel can be observed. It is suspected that these oscillations can influence the converter's structure. The exchange of forces between fluid and the surrounding vessel is the focus of this study. An oscillation model was developed and tested, one objective being to limit the computational effort which is necessary for fully coupled and time resolved CFD and FEM simulations. Experimental results obtained from water-model studies as well as from on-sight measurements are available and were used in order to validate the numerical results. The authors' intention is a contribution towards a more in depth understanding of the factors influencing vessel vibration during the AOD process.IntroductionDuring the last four decades the AOD process has been established as a reliable and efficient refining process in stainless steel making. The injection of process gases (O2, N2, Ar) through sidewall nozzles shows advantages in mixing effectiveness compared to other injection geometries e.g. bottom blowing [1]. Stainless steel grades contain usually more than 10% chromium. With decreasing carbon content during the decarburization periods the tendency of chromium oxidation increases according to the varying chemical equilibrium which depends on the partial pressure of carbon-monoxide (CO) in the gas phase. That's why oxygen is gradually replaced by inert gases, usually argon or nitrogen, in order to lower the CO partial pressure and thus to minimize chromium oxidation. Despite the high injection velocity of approximately Ma = 1, the kinetic energy of the gas jets is consumed within a short distance from the nozzle exits due to the large density ratio between gas and melt of approximately 1:8000. With increasing distance to the nozzle exit, the initial horizontal velocity of the gas jet decreases and due to buoyancy force motion of the detached bubbles turns into a vertical direction. Subsequently a gas plume develops with its typical conical shape described by various authors [1-4]. Due to the drag force between gas bubbles and melt also the liquid phase is forced into a vertical motion. Near the free surface and the wall regions the melt flow is deflected in different directions. Subsequently, the typical flow pattern in the AOD vessel arises, as sketched in Figure 1 and described in literature [5-9]."

Jan 1, 2012

By N. V. Sujathkumar, I. Vasudhevan, R. Santhakumar

"Freshwater ornamental fish culture is gaining importance in India and cheaper and nutrient rich live foods such as infusorians, daphnids, copepods and tubifecids are needed urgently. In this regard, adequate research has been conducted to produce such live feeds through recycling of agriculture and animal wastes. By this venture, besides generation of additional income, environment is also kept clean. In order to popularise the technologies relating to production of live foods from wastes and generate employment opportunities, training programmes were conducted for 100 Self Help Group women belonging to Thoothukudi district. The topics of the training included, breeding of ornamental fishes by utilizing the building material wastes, production of live foods through recycling of agricultural and animal wastes. A study on feed back was conducted with 100 respondents represented from different villages. The variables such as socio economic status, economic motivation, usefulness of training and constraints were included in this study. The impact assessment of this training of rural women indicated that 79 percent respondents were in favour of using the training for self employment by utilizing different kinds of wastes. Similar training programmes have also been planned in other parts of Tamilnadu. Introduction Ornamental fish culture is one of the most appropriate sectors to provide opportunities of employment to uplift the status of rural women. To ensure women utilize their full potential in useful and profital activities like freshwater ornamental fish culture, it is necessary to provide training and support for rural women which will ultimately lead to empowerment. Self Help Group Women are being trained routinely in India on the production of live foods for ornamental fish culture through recycling of agricultural and animal wastes. In this regard, training programmes were organized for the Self Help Group Women on freshwater ornamental fish culture. Which is gaining much importance in India. Cheaper and nutrient rich live foods such as infusorians, daphnids, copepods and tubifecids are needed urgently. The techniques of live feed production through recycling of agricultural and animal wastes would not only generate additional income by would also keep the environment clean."

Jan 1, 2008

By E. Anelli

Based on experimental continuous cooling transformation (CCT) diagrams, an artificial neural network has been trained to predict the amount of microsturctural constituents and hardness resulting from and controlled cooling at rates from 150 to 0.015 K/s. It can be applied to quenching and normalizing processes of low-alloy steels with 0.05-0.30 C% and 0.4-2.0% Mn -with possible microalloying additions. Examples of the good predictive capabilities about 15 Vickers standard deviation for hardness and a few percent for volume fraction of phases) are reported' Keywords: Austenite decomposition, low. And medium-carbon steels, artificial neural networks

Jan 1, 2003

By A. Pagliero

The coulombimetric reduction method has been used as an evaluation technique for Pb-Ca-Sn anode corrosion in the LIX-SX-EW process. The proposed methodology involves three consecutive steps, i.e., cleaning, oxidation and reduction. They are carried out in the same experimental unit, in solutions containing 180 g/L H2S04 with and without the addition of cobalt. The authors have worked in a wide range of oxidation current densities, from 150 to 500 A/m2 for in a period from 0.5 to 120 hours. It can be concluded from the results that there would be a linear relationship between the applied electrical charge I*T (Coulomb) and the anode corrosion expressed as transformed Pb mass (mg), for solutions with or without the addition of cobalt. The exception is that for the last one the corrosion rate is 5 times faster, which was observed for every layer. From the evaluation of different corrosion layers, one can point out that its composition is mainly in the form of sulphate. In the presence of cobalt, about 67% of Pb would be as sulphate (PbSO4), about 27% as a basic oxide (PbO) and only 6% as oxide PbO2 on the surface. From this result, it appears that great transformations occurred in the metal/sulphate interface. Without the addition of cobalt, the proportion of oxide Pb02 on the surface increased up to 11.5%. According to the previous statement and considering that Pb was found mainly as sulphate, the authors recommend its determination be used as quality selection criterion. Its evaluation should be performed in the acid solutions with 200 ppm cobalt addition at an oxidation current density of 300 A/m2 for a period of 24 hours.

Jan 1, 1999

By E. A. Thiers

The causes of structural changes in the markets for high technology alloying metals are discussed in terms of technological, economic, and financial trends. Recent market imbalances have affected producers in developed and developing countries differently. Possible response strategies for suppliers in the two types of countries are examined that may alleviate future market imbalances.

Jan 1, 1988

By Xiaobing Yang, Animesh Jha, Greg Doughty

"Successful use of inert anodes should reduce the CO2 footprint in aluminum production. The search for a “holy grail” inert anode for metal electro-winning from constituent oxides using molten salt bath as an electrolytic medium is continuing. In this article we demonstrate the engineering approaches for the fabrication of intermetallic anodes, based on a quaternary Al-Ti-Cu-M (M:Ni, Fe) system for primary aluminium production. In particular, we examine the microstructural and electrochemical properties of alloys, based on the quaternary compositions. We explain the aspects of phase stability under anodic potential, which leads to the loss of anodic materials in the temperature range of 850-1050oC. The results are analysed in the context of oxidation reaction and formation of oxide layers which readily dissolve in the cryolite melt and prevent passivation. The paper also describes the conditions under which the reduction of aluminium at the graphite cathode occurs which also strongly depends on the molten salt chemistry for the nucleation of molten aluminium at the cathode.1. IntroductionOxygen-evolving inert anodes are an alternative to the conventional consumable carbon anodes for the production of primary aluminium. In this paper the materials selection criteria chosen for the engineering of anode is based on the understanding of the thermodynamic stabilities of aluminide intermetallic phases, some of which are formed and remained stable in fluoride melts. For example, the formation Al3Ti dispersed in aluminium metal via molten-fluoride flux reaction is well known in the context of aluminium casting and grain refining [1-3]. It is for this reason in our research we concentrated on the engineering of stable intermetallic phase mixture in the Al-Ti-Cu ternary system, shown in Figure 1 [4]. In this figure two compositions in the Al3-0.5zTi1-0.5zCuz family are shown with the substitution of 7 atomic % and 11 atomic % copper. However initial investigations showed that these two compositions were unsuitable due to the formation of low-temperature liquid (~540oC) and intermetallic phase, Al2Cu along the Al-Cu binary edge during solidification. The Al2Cu phase segregated along the boundaries of Al3Ti and Al5Ti2Cu, and dissolved away when electrolysis was carried out using these anodes above 800oC. The presence of consequential porosity in the anode material increased the corrosion of the alloy through local heating due to high current density at 0.8 A cm-2. The early tests were carried out with cryolite melts, shown in Figure 2, having 3 weight percent of Al2O3 in the bath at 850oC."

Jan 1, 2010

By Roma T. Dec

Many industrial wastes may require preliminary processing to change their particle size, density, surface properties or flowability to become more suitable for treatment and recycle. This can be achieved by pressure agglomeration using roll presses. In the following paper an overview of various roll press processing methods like briquetting, compacting, compacting-granulating or densification is presented together with basics of process and equipment design. The emphasis is focused on major factors influencing compaction process and responsible for pressure build up and final product quality. Finally, two examples of roll press application for briquetting of steel plant wastes and compaction of alumina base catalyst tailings are introduced.

Jan 1, 1996

By Guo Chen, Jin Chen, Jinhui Peng

In this paper, solving common problem of electrostatic precipitator (ESP), which was frequently ruptured of the cathode insulation in the production process were studied. The microwave heating airflow technology was introduced, which takes full advantage of its unique properties, solves the output problem of the high temperature air, achieves purpose of energy conservation, important economic significance and environmental significance. The mathematical models and designing of microwave high-temperature hot air system was calculated. The common forms of heat exchangers and comparative analysis were also introduced. The conditions found to be at the temperature of 240 °C. Under optimum conditions, the microwave heating power was 1482 W. Based on the mention results, this microwave heating method can be applied effectively and efficiently way for the production process of electrostatic precipitator.

Jan 1, 2015

By Kenneth L. Reid

The Mineral Resources Research Center at the University of Minnesota has recently installed a QEM*SEM system (Quantitative E.valuation of Materials using Scanning Electron Microscopy) to aid in detailed mineralogical evaluation of potential mineral resource developments in Minnesota and to provide services to the North American mineral industry. A primary application for the unit is to serve the Minnesota taconite industry by providing mineralogical analysis of ores and concentrator products. Minnesota taconite ores contain fine-grained magnetite in a quartz matrix. The ores undergo several size-reduction/magnetic-separation steps to produce a final concentrate with approximately 75% passing 325 mesh and containing about 5% gangue. The paper describes a typical taconite concentrator flowsheet and reports some preliminary results of the applications of QEM*SEM particle image maps and cumulative yield liberation data to samples from selected points in the concentrator circuit.

Jan 1, 1988

By Masaaki Naito

The Japanese steel industry has a long history of introducing new and innovative technologies in the field of ironmaking. The new technologies introduced during the past ten years include technologies to use cheaper and lower-grade raw materials and fuels, measures to prolong the service life of blast furnaces and coke ovens, promotion of energy saving, use of wastes and solutions to environmental problems. This report outlines the condition of production and technological trends and technical development themes in ironmaking technologies.

Jan 1, 2006

By Rafael Padilla

The recovery of copper from chalcopyrite concentrates by leaching is difficult due to the slow dissolution kinetics of this mineral in most leaching media. However, recovery of copper from sulfidized chalcopyrite (a mixture of CuS and FeS2) by leaching is faster and could be selective depending on the leaching media. In this paper, the result of an investigation on the H2SO4-O2 pressure leaching of sulfidized chalcopyrite is presented. The variables considered in the study were stirring speed, concentration of sulfuric acid, temperature, and partial pressure of oxygen. The experimental data indicated that stirring speed over 500 rpm and sulfuric acid concentration over 0.1 M had very little effect on the leaching rate. An increase in temperature from 90 to 100 ºC increased both copper and iron dissolution; however, further increase to 120 ºC affected negatively the copper dissolution. Oxygen partial pressure was found to be the main variable that controls the copper/iron selectivity of the leaching. An increase in oxygen partial pressure increased significantly the rate of copper dissolution but deteriorated the copper/iron selectivity. The analysis for sulfur of the leaching solid residues indicated that most of the copper sulfide sulfur in the sulfidized concentrate oxidized to elemental sulfur.

Jan 1, 2006

By Renaud Metz

The DOPA process (Direct Oxidation of a Precursor Alloy) was used to prepare ceramic powders based on doped SnO2 and ZnO. The DOPA process consists essentially in the direct oxidation of a homogeneous precursor alloy. A unique advantage of this process is its rather benign environmental impact since no dangerous reactants are used and no harmful by-products are generated. Only oxygen and the alloy metals participate on the chemical reaction to produce the multi-component oxide. Homogeneous alloys of niobium, cobalt and chromium doped tin have been prepared. The molten metal alloy is atomised in air using a double fluid nozzle to produce metallic powders. A subsequent thermal treatment is carried out to fully oxidise the sprayed metal alloy powders. These raw powders are used to prepare a ceramic powder through a mill homogenisation and atomisation process. The ceramic powder is then uniaxially compacted in disc shape and sintered in an oxidising atmosphere. The resulting sintered bodies are metallised on their flat faces and the cylindrical surface is passivated using lead free glass enamel. These ceramics present excellent semiconducting properties with non-linear (non-ohmic) characteristics. The DOPA process is found to be an attractive procedure to obtain ceramic powders for the preparation of SnO2 varistors.

Jan 1, 2006

By Hideyuki Takahashi, Taro Aichi, Kazuyuki Tohji, Makoto Muramatsu, Rie Sato

"There are several ways to condition lead-based alloy anodes for zinc electrowinning: electrochemical treatment, chemical treatment and physical treatment. Two advantages of physical treatments are their productivity and variety. In this report, physical treatments, including blasting with silica, alumina, steel grit and cut zinc wire, were tested. The laboratory tests confirmed there were differences in the formation of anode scales during electrowinning and in the suppression of lead dissolution from the anodes. With an increase in the surface roughness, the misfit between the PbC""2 and the MnC>2 was mitigated and the anchor effect was promoted; these effects resulted in dense Mn oxide scales on the anode.IntroductionZinc is widely used for hot-dip zinc plating and for die casting alloys. As a supplier of materials, we have endeavored to produce zinc that is economical and contains as little impurity as possible. As a result of our efforts, a technology for consistently providing special high-grade (SHG) zinc has been established. However, as seen in the issuance of the Restriction of Hazardous Substances (RoHS) Directive, public awareness of the industrial impact of heavy metals on the environment has been heightened. Increasing efforts to control environmentally sensitive substances will be necessary for our production processes.Electrolytic SHG zinc is produced by electrodeposition in an acidic solution with a Pb-Ag or Pb-Ag-Ca alloy for the anode and an Al alloy for the cathode. Pb alloy anodes are widely used because of their excellent durability; however, they are a source of Pb, which is the main impurity of the product."

Jan 1, 2012

By Shun Fujieda, Shigeru Suzuki, Kozo Shinoda, Tetsuo Fujita

"Dowa's scorodite, synthesized by oxidation of Fe(II) ions in the presence of As(V) ions at atmospheric pressure, was characterized. The scorodite was well crystallized and had a very low solubility. To examine the conditions for stable storage of the scorodite for long periods, experiments with various synthesis and leaching conditions were done. The scorodite had a very low arsenic solubility in sea water. It was estimated in consecutive leaching tests that the arsenic concentration would eventually converge to zero. The prevention of arsenic leaching by adding goethite or ferrihydrite was limited in some cases. Very low toxicity was confirmed by toxicity tests. The investigation results suggest that disposal at a specifically designed well-controlled storage place is preferable for the scorodite whose toxicity had been made sufficiently low. Disposal to an isolated final disposal site with more stringent prevention for the outflow of toxic substances was thought another option.IntroductionArsenic is a considerable environmental concern. A system of technologies for the effective immobilization, storage and final disposal has been sought. Dowa Metals & Mining Co. Ltd. has developed a unique scorodite synthesis method (DMSP®) which works at ambient pressure [1]. The scorodite is precipitated by oxidizing Fe(II) ions in a high-concentration As(V) solution. The scorodite produced in this way does not readily release arsenic because of its high crystallinity. Final disposal is necessary because scorodite currently has no commercial value. A standard method for the final disposal of scorodite has not been established because its long-term stability under various conditions has not been fully examined."

Jan 1, 2012

By C. M. Egert, S. Rajic

"We have developed a monolithic micro-spectrometer suitable for a variety of sensing applications including industrial process monitoring. The device consists of a solid structure with a volume less than 6 cubic centimeters. All optical components of the spectrometer including two aspheric mirrors, a diffraction grating, and entrance and exit surfaces are fabricated onto the surface of the structure. All light paths are internally contained within the structure. The result is a small, rugged spectroscopic sensor ideally suited for use as a process monitor. Due to its monolithic nature the device requires no post-fabrication alignment; nor can it be knocked out of alignment during use. Although many materials and thus wavelength regions were possible, the prototype device discussed here was produced in PMMA by precision diamond turning. However, lower cost manufacturing approaches involving injection molding are under development to produce an affordable sensor.Due to its rugged monolithic design, small footprint, and low cost the monolithic micro-spectrometer is ideally suited for distributed monitoring applications often required for industrial processes. It is expected that modified versions of this sensor designs will be required for specific applications so as to maximize the performance and resolution over the operating range. For example, the prototype device described here operates over a wavelength range of 500 nm to 1000 nm. The performance of this device as a real-time surface monitoring sensor will be discussed in detail. Our approach of using wavelength dependant scattering resulted in the reduction to practice of a miniature, monolithic, rugged, low-cost, micro-instrument in a sensor sized package. The process sensor applications community has been faced by the cost versus performance issue. Simple go/no-go sensors are typically inexpensive but they provide very limited and sometimes dubious data. Scaled down traditional instruments offer very good measurand information but are typically cost prohibitive, fragile, and still relatively large. This work will bridge the gap between these two extreme sensing alternatives."

Jan 1, 1997

By Xuyang Liu, Xuewei Lv, Chenguang Bai, Meilong Hu

"The electro-deoxidation process for ilmenite concentrate in molten salt was studied by cyclic voltammetry and AC impedance spectroscopy. The results from cyclic voltammetry are consistent with those of AC impedance spectroscopy. The results showed that the electro-deoxidation process for ilmenite concentrate consists of two steps. In the first step, Fe is reduced from the ilmenite concentrate. The second reaction is the decomposition of TiCh. CaTiCh is an intermediate product. At low voltage, the electrochemical reaction is the main step. With the increasing potential, the diffusion of ion is the main rate controlling step for the electro-deoxidation of FeTiO3.IntroductionTitania and titanium-rich products are mainly prepared from ilmenite concentrates (FeTi03), which contain about 40%-60% T1O2 after ore dressing and other physical or chemical processes [1]. At present, the main methods to prepare titania are the sulfuric acid process and the chloride process, but the sulfuric acid process consumes a large amount of sulfuric acid and the materials requirements for the chloride process are strict [2], Since the Electro-Deoxidization in Molten Salt (FFC) method was put forward in 2000, many researchers have successfully extracted the metal and alloys by this method, such as Ti, Cr, Tb, Si, Al-Si, TiV, FeTi, etc. [3-7], FeTi alloy is a typical hydrogen storage material, and because of its favorable properties, the preparation of FeTi alloy has become a hot research topic [7-9]. However, the mechanism of electro-deoxidization has not been studied thoroughly [10-11]. Therefore, in this study, the electro-deoxidation process for titanium concentrate was investigated by electrochemical methods, and the study makes a contribution to improving the current efficiency of the electrolysis."

Jan 1, 2012

By Pinakin Chaubal

The campaign life of a modern blast furnace depends on hearth wear. Distributions of liquid iron flow and refractory temperatures have a significant influence on hearth wear. A 3-D comprehensive CFD model has been developed specifically for simulating the blast furnace hearth. It includes both the hot metal flow and conjugate heat transfer thorough the refractories. The model has been extensively validated using measurement data from actual blast furnaces. Good agreements between measured and calculated refractory temperature profiles haven been achieved. It has been used to analyze the velocity and temperature distributions and wear patterns at different furnaces and conditions. The results can be used to point out the directions for protecting the hearth.

Jan 1, 2006

By Vladimir Lobanov, Vladimir Skorohodov, Boris Radionov, Olga Makovskaya

"The synthetic sorbents and the activated carbons which are used for the metals extraction from weak process liquors are rather expensive. It is propose to use mineral and synthetic high-porous substances which sharply increased sorption properties by special processing. For achievement the desirable properties sorbents are impregnated by specially prepared solutions. Such solutions should contain the substances or its anionic forms which on the one hand are strong enough fixed in a supporter pores, with another are capable to form the insoluble compounds with extracting metals. Selectivity is provided by chemism of the reagent interactions with extracting metal. Due to the high concentration of a reacting ion in a sorbent phase the capacity and rate of sorption increases. Formed insoluble compound remains in a phase of the sorbent and necessity of its filtration disappears. For synthesis the sulfhydryl compounds which chemical properties allow to increase degree of extraction and capacity of the activated carbon were used. At hydrometallurgical processing of precious metals mineral raw materials the commercial solutions with the concentration of gold from 0,1 to 5 mg/dm3 are received. Commonly gold is precipitated from cyanic solutions by the zinc dust. The sorption methods are widely applicable. But the synthetic sorbents and the activated carbon using to these purposes are rather expensive. Expenses for sorbents even at its regeneration can reach 10-15 % from total expenses of gold extraction from ores. When sorbent regeneration, mostly for carbon, is not provided, this share increases to 30-40 %. Thereupon search of the sorbents combining availability, the sufficient capacity, demanded degree of extraction and the low price is actual. For the specified purpose it is offered to use the mineral and synthetic high-porous materials which sorption properties are sharply rose by special treatment. Among such substances are natural zeolites, silica gel, lignine et al. Similar treatment can improve the sorption properties of sorbents used in practice, particularly, the activated carbons. The simplest treatment of potential sorbents consists in its impregnation by specially prepared solutions. Such solutions should contain substances or its anionic forms - impregnating agents. These agents should be on the one hand strong enough fixed in a carrier pores, on the other hand are capable to form with extracting metals insoluble compounds. The more strong compounds are formed the high degree of metals extraction from solutions. The sorbents with similarly changed properties are named the impregnated sorbents."

Jan 1, 2008

By Yanping Xiao

In submerged-arc furnace (SAF) for smelting chromite ores into ferrochrome, there exist large temperature gradients and wide distributions of mineralogy and compositions in the furnace, due to the complexity of feed structure and electrical-thermal-chemical interactions. This leads to various zones in the furnace and thus different reaction mechanisms. In the present paper, the behaviour of chromium in the submerged arc furnace is discussed in various reaction zones, including solid state chromite reduction in the packed bed zone, chromite dissolution and reactions in the smelting and coke bed zone, and recovering chromium from slag to metal. In the gas-solid reaction zone, the reaction mechanism is discussed based on the experimental observations and analysis. In the smelting zone, the behaviour of partially reduced chromite and slag formation are analyzed based on the information in literature. The slag in FeCr process contains mainly Al2O3, MgO, SiO2, CaO and CrOx, featured by chromium with both divalent and trivalent oxidation state, which plays an important role for chromium recovery into metal. The factors influencing the slag and metal interfacial reactions and the chromium recovery are addressed.

Jan 1, 2006