Search Documents

By Carlos Ortiz

The Huelva Flash Smelting Furnace was commissioned in September 1975. The Smelter and the Acid Plant were expanded in 1995 to their present capacity of 300,000 tpa new copper equivalent and one million tonnes of concentrate per year. During these years of operational experience, most of the initial practices have been reviewed, process control has drastically improved and main process equipment has been modernised. The fourth Flash Furnace campaign lasted 9 years (1995-2004) during which 8 million tonnes of concentrate were smelted. Increasing sulphur content in concentrates and new environmental requirements imply new challenges for smelters to keep production and operation costs down. This paper is an overview of the modifications and improvements carried out in the 2007 general shutdown in Smelter and Acid Plants. Al

Jan 1, 2008

By Berndt Moeller

Mercury-cell chlor-alkali production plants generate mercury contaminated wastewater streams from which mercury must be precipitated and filtered, resulting in a sludge containing 2% mercury (designated KI06) that cannot be landfilled in the United States without treatment. REMERC is a chemical treatment process used to recover 99% of the mercury from wastewater sludge generated at these plants. The process uses leaching to oxidize mercury compounds to mercuric chloride, washing and filtration to separate mercuric chloride from the treated sludge, and cementation to reduce the mercuric chloride to metallic mercury. Mercury not recovered in cementation is recycled to the wastewater process for precipitation and filtration. Treated sludge contains less than 260 ppm total mercury and 0.2 ppm TCLP, meeting the USEPA low mercury subcategory specifications that allow landfill disposal. REMERC uses readily available chemicals, is straightforward to control and inexpensive to operate, has no mercury emissions to air, and recovers metallic mercury. REMERC enabled significant cost savings including lower solids disposal costs, recovery and reuse of metallic mercury in the chlor-alkali process, and ability to treat non-wastewater sludge. No new EPA permits were required. REMERC was shown to be a viable process for recovery of metallic mercury from K106 designated sludge.

Jan 1, 2003

By Thomas Brynjulfsen, Merete Tangstad, Eli Ringdalen

Manganese ore fines cannot be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace, they are typically agglomerated into sinter. In this work, the melting and reduction properties of Gabonese sinter and Gabonese ore have been investigated in pilot scale experiments. Two experiments were conducted, one with 100% sinter as manganese source and one with 50/50 sinter and ore. Lime was used to achieve a charge basicity of 0.72 in both experiments. The composition of slag samples from the excavation of the furnace was established using EPMA(WDS), and the composition of the tapped slag and metal was found using XRF. It was found that while the coke-bed size would determine the tapped slag composition, the melting behavior of the Mn source would determine the mixing with lime.

Jan 1, 2014

By John Anawati

Bauxite residue is an environmentally unfriendly byproduct of alumina manufacturing, produced worldwide in large quantities. This material contains 50– 100 ppm of scandium, a critical material for the production of stronger, weldable, corrosion resistant, and heat tolerant aluminum products. Aircraft manufacturers are particularly interested in Al–Sc alloys because of its ability to form weldable alloys that could potentially reduce aircraft weight by 15–20%. Because of its abundance and low cost, bauxite residue has the potential to be used as an efficient feedstock for valorization processes to recover its scandium content, while in turn degrading this problematic waste. In this project, we developed an efficient process to recover scandium and rare earth elements from a Canadian bauxite residue with high extraction yields, using industrially scalable and economical techniques. The process employs a modified version of sulfuric acid leaching and subsequent impurity removal by selective precipitation. This article outlines the current progress and design rationale in the development and optimization of this innovative and sustainable recovery process.

By Brandon R. Ball

An investigation of the effects of ozone and ozone-induced hydroxyl radical on reducing whole effluent toxicity is described and discussed relative to the application of ozone for industrial water treatment. Results from operation of an ozone system treating industrial effluent from a lead and zinc mine in Colorado are presented. The mine discharges 1,000 gpm of wastewater into a tributary of the Arkansas River and has historically exceeded Whole Effluent Toxicity (WET) limits and on occasion has exceeded numeric limits for copper, ammonia, and cyanide. Based on results of a Toxicity Identification Evaluation (TIE) conducted on the effluent and individual process waste streams, the source of effluent toxicity is believed to be primarily associated with organic reagents used in the milling process. Based on test results, an applied ozone to COD ratio of 3: 1 by weight and a contact time of 30 minutes was found to be effective for reducing whole effluent toxicity at pH 11 but not at pH 7, indicating oxidation by hydroxyl radical to be the dominant mechanism responsible for toxic-ity reduction. At an applied ozone to COD ratio of 3:1 and a pH of 11, toxicity was improved from 0 percent survival to 100 percent survival for Ceriodaphnia dubia and fathead minnow (Pimephales promelas) based

Jan 1, 1996

By Tom Marttila

During the last few years, when a new tankhouse or a major modernization has been planned, automatic or semiautomatic crane and grab systems have at least been considered. It seems that in the future tankhouse managers for new, modernized and even old tankhouses will be looking for a proven and reliable system for automatically moving and positioning electrode loads in the tankhouse and in storage areas. In this paper, we will describe the Wenmec solution for automatic electrode handling. The advantages of automatic handling and very accurate electrode positioning will be discussed, and the way Wenmec has solved the problems in mechanical construction and in automatic, accurate and reliable positioning will be presented.

Jan 1, 1990

By Munetaka Iwasaki

Nitrogen strongly affects mechanical properties of steel and therefore we may sometimes modify the various processes for its content. Numerous studies based on the results of chemical analysis of quenched samples were reported with a few exceptions of Hot Sievert method. The technique always poses a risk of uncertainty whether the true content of nitrogen in liquid metal is measured or not. In this study vacuum remelting under relatively low pressure was done to enhance gas phase mass transfer. Total pressure of the melt chamber was about 10-3 pa and electron beam heating was used. Mass spectroscopy was used for the direct observation of the rate of denitrization. Nitrogen molecules or atoms were detected by a mass spectrometer set above the melt. Continuous monitoring of the intensity of the fixed mass number may reflect the transfer of nitrogen from the melt to the vacuum. The results of the new and conventional techniques agree, both technique can be verified.

Jan 1, 1999

By C. Geenen

At its Olen site, Union Minière Copper operates a new full-size deposit tank house. A first 200,000 t/y module was commissioned in October 1996, and an additional 130,000 t/y unit started in April 1998. The main objectives of the new tank house project were to produce grade A cathodes starting from anodes with a wide range of compositions and at a minimal operating cost. The tank house uses Isa Process technology. Based on the process parameters agreed upon with MIM, UM Copper developed the basic design and UM Engineering was the in-house contractor for the engineering. The new tank house is equipped with advanced technology polymer concrete cells, automated two-bale cranes and high-capacity machines. The first 200,000 t/y module treats anodes with a more conventional composition at 330 A/m2; the second 130,000 t/y module treats anodes with a high slimes fall (12- 13 kg/t) at current densities up to 285 A/m2. After some teething problems, the new tank house is meeting all set targets. This paper illustrates and comments on the design characteristics and operational results.

Jan 1, 1999

By H. Kandemir

An experimental study of the bacterial oxidation of naturally occurring high-purity sulphide minerals (FeS2, Fe1-xS, Cu5FeS4, ZnS) is presented using a mesophilic strain of T. ferrooxidans. As well as metal analyses and solution pH, partitioning of sulphide sulphur into elemental sulphur and sulphate has been monitored as a function of leach time. Partially oxidized sulphide substrates have been characterized, at regular time intervals, by X-ray diffraction methods and extracellular organic compounds reporting into leach solution .have been identified by thin layer -chromatography.

Jan 1, 1985

By S. S. Babu, T. Hong, T. DebRoy, S. A. David

"Oxide inclusions form in welds because of deoxidation reactions in the weld pool. These inclusions control the weld microstructure development. Thermodynamic and kinetic calculation of oxidation reaction can describe inclusion characteristics such as number density, size, and composition. Experimental work has shown that fluid-flow velocity gradients in the weld pool can accelerate inclusion growth by collision and coalescence. Moreover, fluid flow in welds can transport inclusions to different temperature regions that may lead to repeated dissolution and growth of inclusions. These phenomena are being studied with the help of computational coupled heat transfer, fluid-flow, thermodynamic, and kinetic models. The results show that the inclusion formation in steel welds can be described as a function of the welding processes, process parameters, and steel composition.IntroductionThe relationship between inclusions and formation of a high-toughness phase, namely acicular ferrite in low-alloy steel welds, is well known (1-4). Past research has focused on maximizing acicular ferrite amount in welds by controlling welding processes, process variables, and welding consumable parameters. Research has shown that there is a complex interaction between inclusion characteristics, prior austenite grain size, and weld metal hardenability. In a low-alloy steel weld, the small addition of titanium lead to a change in the inclusion composition and resulted in a transition in the microstructure from bainitic to acicular ferrite [see Fig. I]. This in turn lead to the best combination of strength and toughness. This paper describes the inclusion formation in low-alloy steel welds."

Jan 1, 1999

By Eric J. Grimsey

Steady state Excel models for a copper flash smelter and an iron blast furnace are used to enhance the teaching of pyrometallurgical smelting principles within a fourth year level process engineering unit delivered at the Western Australian School of Mines. A lecture/workshop approach has been adopted in which student teams undertake process simulation assignments that illustrate the multifaceted responses of process outputs to variation of inputs, the objectives being to reinforce their understanding of smelting principles. The approach has proven to be popular with students, as evidenced by the consistently high ratings the unit has received through student feedback. This paper provides an overview of the teaching approach and process models used.

Jan 1, 2014

By Roger Wilmoth

Exposed, open pit mine highwalls contribute significantly to the production of acid mine drainage (AMD) thus causing environmental concerns upon closure of an operating mine. Four innovative technologies were evaluated under the U.S. Environmental Protection Agency?s, Mine Waste Technology (MWTP), Prevention of AMD Generation from Open-Pit Highwalls Demonstration Project. This project is funded by the U.S. Environmental Protection Agency (EPA) and jointly administered by the EPA and the U.S. Department of Energy (DOE) through an Interagency Agreement. The objective of the field demonstration was to evaluate the technologies ability to decrease or eliminate acid generation from treated areas of the highwall in comparison an untreated highwall area. The field demonstration was performed at the Golden Sunlight Mine (GSM) a subsidiary of Placer Dome U.S., located near Whitehall, Montana. GSM is an operating gold mine. The highwall at GSM was divided into five plots measuring 15.24 by 15.24 metres (m) and each technology was assigned a plot with the fifth plot being used for comparison as a background control plot. The four technologies were spray-applied. The applied insitu treatment technologies included: 1) A modified, furfuryl alcohol resin sealant, utilizing wood and agricultural by-products to coat the rock surface. 2) EcobondTMARD, a phosphate based process that forms a stable, insoluble compound, coating the rock surface. 3) Two ARD passivation technologies, magnesium oxide and the Dupont technology developed to create an inert layer/coating on the pyrite, preventing oxidation. The technologies were evaluated using the following methods: 1) ASTM D 5744-96, Accelerated Weathering of Solid Materials using a Modified Humidity Cells, 2) mine wall residual wall rinse sampling, 3) microscopy, and 4) core drilling followed by water injection testing.

Jan 1, 2003

By Lichao Ding, Chunhua Liu, Yunnen Chen

"In this paper the simulated acid magenta dye discoloring the reaction process was researched. The results showed that it attained highest decolorization efficiency for acidic magenta simulation dye wastewater when pH 9 and reaction time 10 min. With the initial dye wastewater concentration increased, the decolored rate decreased. The decolored rate in general kept a tendency to increase with the temperature increased. Kinetics researches showed that when pH 9, reaction temperature 20 and 35 ?, the decoloring reaction process for the dyes accorded with the First-order dynamic equation. The decoloring reaction rate constant was influenced by initial concentration of dye wastewater and temperature.1. IntroductionIn China, textile printing and dyeing industry is one of industrial departments which using more water and discharging more wastewater. There is about 7 billion tons of waste water discharge each year, of which 80% from the process of printing and dyeing. Being complex ingredients, high chroma, more toxic substances and severe environment pollution, the treatment of printing and dyeing wastewater becomes problem urgent to be resolved. The traditional treatment methods such as adsorption [1], coagulation [2], biochemical method [3,4], which has advantages of simple equipment, simple operation and mature process, but they can cause waste accumulation and secondary pollution [5,6].Magenta is a kind of organic compounds, which classified into acid and alkaline magenta. Considering the advantages of simple operation, low cost, simple experiment equipment and friendly to environment, acid magenta dyes wastewater was chose as object in this paper. Some parameters such as pH, contact time, temperature and the initial concentration on of simulative acid magenta dyes wastewater were studied."

Jan 1, 2012

By Daoxin Wu, Zhong Cao, Yan Shi, Yu Ding, Huanli Yang, Zhongliang Xiao

"2-substituted benzimidazole-zinc and 2-substituted benzimidazole-copper complexes were main components of organic solderability preservative (OSP) in PCB producing process and affect the thermal stability of OSP film. So these four complexes were prepared by 2-substitutedbenzimidazole reacting with zinc ion and copper ion, the complexes crystals were determined by IR, its thermal stabilities were studied by TG method. The results indicated that the thermal stability of 2-substituted benzimidazole-zinc is higher than the 2-substituted benzimidazole copper,and the thermal decomposition mechanism was presentedIntroductionImidazole compounds which is an important heterocyclic compound shows the important value and outstanding prospects[I-3l in field of biological engineering, medicine, and high-performance composites. It's said that imidazole compounds is an excellent new metal surface treatment[4] agent, because it has good reaction activity with metals and can form a chemical layer on the metal surface. The complexes of imidazole were main components of organic solderability preservative (OSP) in PCB producing process and affect the thermal stability of OSP film. The mechanism of imodazole combined with metal and film deposited has been reported, but the opinions about thermal stability of film have bifurcation, let alone the thermal decomposition mechanism of film at high temperature. The complexes were prepared by combining of 2- substituted-benzimidazole with zinc and copper iron, which were studied by IR and TG method, in order to get thermal stability of different complexes."

Jan 1, 2011

By Mark Jolly

"Over the last ten years or so many man hours have been dedicated to developing methods for simulating shape casting processes. The majority of the methods developed have been devised by a combination of computer, mathematics and materials specialists often with limited knowledge of foundries and foundrymen. As a result of this it would appear that although there are many software packages for the foundryman to use there still exist fundamental misunderstandings as to their usefulness and suitability within the foundry.The paper aims to identify how well current software packages perform. The relationships between physical phenomena, practical defects and software capabilities are presented. Some discussion of the use of criteria functions is also presented. Finally issues arising from the postprocessing of results are discussed as the presentation of the results to the lay-person in simulation techniques is possibly one of the most important aspects in influencing the adoption of this type of software in the foundry community."

Jan 1, 1999

By Jozef Zmik, Sergey Dobatkin, Martin Fujda, George Raab, Libor Kraus

"The present work, likewise, deals with grain refinement of medium carbon steel AISI 1045 having different initial microstructure resulting from thermal and/or thermomechanical treatment (TM) applied prior severe plastic deformation. In case of TM treated steel, structure refinement was conducted in two steps. Preliminary structure refinement has been achieved due to multistep open die forging process which provided total strain Eef ~ 3. Uniform and fine recrystallized ferrite structure with grain size of the order of 2-5 µm and with nest-like pearlite colonies was obtained. The further grain refinement of steel samples having different initial structure was accomplished during warm Equal Channel Angular Pressing (ECAP) at 400°C. The microstructure development was analyzed in dependence of effective strain introduced ( Eef ~ 2.5 - 4). Employment of this processing route resulted in extensive deformation of ferrite grains where mixture of subgrains and ultrafine grain was found regardless the preliminary treatment of steel. As straining increases the dynamic polygonization and recrystallization became active to form mixture of polygonized subgrains and submicrocrystalline grains having high angle boundaries. The intensive straining and moderate ECAP temperature caused the partial cementite lamellae fragmentation and spheroidization as straining increased. The lamellae cementite spheroidization was more extensive in TM treated steel samples. The deformation behavior of for both steel structural state confirm the strength increase; however the work hardening behavior was modified with respect to initial structure of steel prior SPD processing.IntroductionIn the last years, ultrafine grained materials have attracted considerable research interest because they tend to possess high strength without sacrificing toughness and ductility. Microstructural refinement of steel is usually achieved by alloying and/or by thermomechanical treatment process, which modifies phase transformation. Recently, advancement of severe plastic deformation (SPD) techniques provides another efficient access for grain refinement of metals and alloys. The fabrication of bulk materials with ultrafine grain sizes has attracted a great deal of attention over the past two decades because of the materials' enhanced properties [ 1, 2]. In last decade a worldwide effort in manufacturing process to obtain ultrafine grain structures in steels is persisting."

Jan 1, 2011

Aluminum has experienced significant growth in automotive applications over the last decade as a result of its properties and performance attributes. Looking to the future, the opportunities for continued growth in powertrain and suspension applications plus light weighting of body structures offer the potential for considerable further growth. This represents a growing "energy bank" of aluminum that will become available for recycling at the end of these vehicles' lives. Today, around 90% of the aluminum is recovered and recycled from scrapped vehicles because of its high value relative to other materials. The future growth offers opportunity for new technology and practices, to maximize scrap quality and recycling application. This paper will review the demand for these new technologies and practices and will discuss industry activities being pursued in this area.

Jan 1, 2000

By L. A. Kazanbayev

The Chelyabinsk Electrolytic Zinc Plant (CEZP) was commissioned in 1935. Over the elapsed years the Plant capacity has been increased from 10 thousand tons of zinc (1935) to 150 thousand tons of zinc (2005). The paper describes the Plant main achievements in production updating for the last 10 years.

Jan 1, 2006

By Pan Cao

The process of reduction roasting of nickel laterite with rotary hearth furnace combined with magnetic separation becomes a very potential way to prepare ferronickel alloy, especially for the low grade nickel laterite ore. In order to realize this new process, the effect of roasting temperature, time and additive on the reduction degree were investigated in the laboratory experimental. The results indicated that the recovery rate of Ni increased with the roasting temperature increasing to 1500°. Most of nickel and a spot of iron are selectively reduced with adding 25.19% SiO2, 6.42% coal, and roasting for 60min at 1500℃. Then conventional magnetic separation was carried out. The content of Ni and Fe are 7.50% and 59.08% in ferro-nickel nugget prepared by this method. And the recovery rate of Ni is 90.91%, which indicates that a high recovery of ferro-nickel from nickel laterite ore is achieved indeed.

Jan 1, 2014

By Tejs Vegge

The lack of suitable means of storing hydrogen for use in the transport sector is generally viewed as a primary showstopper for a hydrogen economy. Recent developments within solid state hydrogen storage in complex hydrides and metal ammines have sparked new hope of a long term solution, but as of now, no materials fulfill all the DoE targets for onboard storage [1]. A detailed physical understanding of the ab-/desorption processes and the role of the essential catalytic additives is an essential prerequisite for the development of new optimized hydrogen storage systems. Here, we illustrate the potential of utilizing the synergy of combining state-of-the-art in theoretical methods and experimental techniques in the analysis and design of materials for hydrogen storage. Recent advances in computer hard- and software has made it possible to treat many of the essential problems in such materials, i.e. structural stability, hydrogen dissociation and diffusion, with high accuracy methods like density functional theory. We rely on such results to guide our synthesis of new materials, and to interpret our experimental results from, e.g. time dependant in situ x-ray diffraction, synchrotron/neutron experiments, and advanced materials testing. Through a continuous feed-back optimization loop between theory and experiments, the obtained nano-scale insight is used to expedite the design and development of novel materials for hydrogen storage.

Jan 1, 2006