Search Documents

By Rikiya Kamezawa, Rudiono, Manabu Takeuchi

"Schottky type solar cells based on phthalocyanine (Pc) thin films were fabricated, and their photovoltaic performance was investigated in various ambient atmospheres. Most of cells prepared in this study showed a good rectification and photovoltaic effects in the visible wavelength region. The introduction ofN02 gas into the measuring chamber was confirmed to increase the current both in dark and under light illumination. However, chemical reaction between the Al electrode and N02 formed some oxide and deteriorated the Schottky barrier, resulting in an increase in cell resistivity. SF 6 gas also showed similar effects on the cell performance.IntroductionPhthalocyanine is one of the typical organic semiconductors, which shows high photoconductive sensitivity in the visible to infrared region. Today, several kinds of metal phthalocyanines are used in electrophotographic photoreceptors. In addition, application of phthalocyanines to solar cells have also been trying by many workers [1, 2]. Many efforts have been made for improving performance of phthalocyanine solar cells by modification of device structure [3, 4], doping by dye or pigment [5, 6] and incorporation of metal clusters [7]. It is known that electrical conductivity in phthalocyanine is increased by adsorption ofNO2 [8, 9]. We tried to improve photovoltaic performance ofphthalocyanine solar cell by adsorption ofNO2. This paper describes the influence of N02 adsorption on the photovoltaic behavior of phthalocyanine solar cells."

Jan 1, 2000

By Luciano B. Oliveira, Luis G. C. Marques, Sergio N. Monteiro, Marcos V. M. Fagundes

"Biodiesel production is normally associated with large plantations of oily vegetables such as soybean and colza, in large rural areas. However, in the municipal limits of the city of Rio de Janeiro, southeast of Brazil, biodiesel is being produced from wastes commonly generated by typical urban activities such as sewage sludge, discarded fat from meat markets and post-used cooking oils. In the present work, the experience of producing biodiesel from urban wastes in Rio de Janeiro is assessed. The type of precursor materials, equipments and logistics are presented. The environmental and economical advantages as well as the drawbacks are discussed.IntroductionThe interest for a liquid fuel that could substitute those obtained from petroleum started more than one hundred years ago when Rudolph Diesel tested his no-spark internal combustion engine, impelled by compression, with peanut oil. By that time, petroleum was beginning to be extracted in large scale and no one was concerned with the future environmental problems and its eventual depletion. In the last century, the successful association of petroleum based fuels with the automotive industry was an almost insurmountable obstacle to any attempt to use nonmineral oils [1]. In addition to the greater efficiency and, by then, lower price of the diesel from petroleum, the use of plain vegetable oils introduced undesirable carbon deposits and reduced the engine lifetime. Today, the situation is reverse. The continuous increase in the price of petroleum and, above all, its contribution to climate changes are strongly motivating the use of biofuels to replace those obtained from fossil fuels such as petroleum, natural gas and coal [2].In the case of the common petroleum derived diesel, many countries are now engaged in large scale substitution programs. The USA should produce more than 700 million litters of biodiesel, while the European Community is expected too produce around 6.5 billion litters in 2008. In Brazil, the federal biodiesel program imposed a minimum of 2% addition to the common diesel. This would demand a production of 800 million litters in 2008 [3]. The Brazilian biodiesel is made from a diversified source of vegetables mainly castor bean, African palm and soybean. The main producers are agrobusiness firms located in large rural areas of the Brazilian hinterland [4]."

Jan 1, 2008

By Xiping Chen, Wangxing Li

"Spent potlining is unavoidable solid waste from aluminum smelters. About thirty kilograms spent potlining is discharged in China to produce per ton primary aluminum. Spent potlining has high level soluble fluorides and cyanides so that it brings heavy pollution to environment. It is prohibited to keep a large amount of spent potlining in open air because it will lead concentrated pollution to local soil and water source due to hydrated reactions between spent potlining and rain water/moisture in air. Landfill may solve pollution of spent potlining provisionally, but it is difficult to be accepted by aluminum smelters because of its high investment, troublesome monitoring and perennial maintenance. Detoxifying of spent potlining not only can remove deleterious fluorides and cyanides in SPL, but also can make fluorides in SPL recycle and return to aluminum electrolysis cells, at the same time benign SPL solid residue can be recycled and ready for cement production.IntroductionChina became the largest primary aluminum manufacturer in 2001. In the past few years, its aluminum output increased by twentyfive percent every year and reached 12.56 million metric tons in 2007. The whole world was very surprised and focused attention upon Chinese aluminum industry. It is more and more important to keep sustainable and steady development with the rapid development of Chinese economy. Aluminum industry is an important base industry and does a great contribution to Chinese economy. But aluminum industry is high energy-consumption and heavy-pollution industry. The government has paid more attention to aluminum industry in recent years. Nowadays the bothersome problem which counterworks Chinese aluminum industry is pollution from solid wastes. Main Solid wastes from aluminum industry are red mud from alumina refineries and spent potlining (short as SPL) from aluminum smelters. Spent potlining are waste lining materials from aluminum electrolysis cells. During production of aluminum, due to reactions between melted electrolyzer and pot lining as well as penetrating of fluorides into pot lining, newly-formed compounds inlayed in pot lining, destroyed the lining structure and brought pot lining cracking. Melt rushed out of lining cracks, cells have to be stopped running and ready for heavy repair. Cell life generally varies from 1500 to 2000 days. Spent potling is an unavoidable solid waste from aluminum industry."

Jan 1, 2008

By Petr Sulovsky, Jaroslava Ledererova, Miroslav Svoboda, Michaela Suchardova

"The thinning resources of natural raw materials necessitate an increased degree of waste material recycling. The building industry offers a range of technologies enabling incorporation of industrial wastes into building materials for construction purposes in an economically acceptable way. Our research is focused on finding the appropriate technologies for specific groups of industrial waste materials (IWM). The studied IWM involve coal combustion residues (CCR), desulphurization products, sludges, metallurgical slags, and various other wastes. Many of them contain increased amounts of toxic elements that can under certain conditions get released. In order to prevent this, each specific IWM requires finding the technology that best ensures the binding of toxic elements in the building matter are fixed for the long term.Introduction The sustainable development of mankind is more than ever viewed as a matter of resources. Many aspects of the switch from a throw-away to a recycling society concern one of the largest consumers of natural resources and producer of greenhouse gases, the building industry. One of the biggest tasks lying before the researchers in the field of building materials is to find substitute or alternative raw materials that would save the thinning reserves of natural resources. The most promising and natural way is to replace the traditional raw materials with rejected and unwanted products of industrial processes, classified as wastes. These of course are not produced with the primary intention of achieving some desired properties. The usage of industrial wastes therefore involves finding the optimal way of usage their existing positive (from the point of view of utilizations) properties and minimizing the impact of their undesired properties, i.e. from the perspective of the considered application."

Jan 1, 2008

By Mao Chen, Baojun Zhao, Zhixiang Cui, Leonel Contreras

Viscosity is one of the important physiochemical properties of metallurgical slags which is important for slag tapping, metal loss in slag, freeze lining and fluid dynamics. High temperature viscosity measurements are time- and cost-consuming and the number of experiments is limited. Viscosity model is an effective way to predict the viscosities of the complex slags at high temperature. However, a reliable viscosity model can only be developed on the base of accurate experimental data. A unique high-temperature viscosity measurement apparatus developed at The University of Queensland enabled accurate viscosity data to be measured for the “FeO”-SiO2-CaO-MgO-Al2O3 system in equilibrium with Fe. An accurate viscosity model has been developed based on Eyring’s theory and extensive viscosity measurements. The viscosities of copper smelting, converting and cleaning slags over a wide range of compositions and temperatures can be predicted and applied in the process control.

Jan 1, 2016

By L. J. Davies

Refractories usage in furnaces for the extraction of nickel from both sulphides and lateritic ores is reviewed. Recent changes in raw materials and basic brick qualities developed to meet the increasing demands of existing and new processes are outlined. Examples of used brick examinations to establish mechanisms of wear are given. The importance of physical and chemical properties are discussed. The use of simulative laboratory testing to aid in refractories development and selection is described.

Jan 1, 1988

By P. E. Donaldson

Since 1992, Falconbridge has made available to the international copper industry, Kidd Creek's licensed refinery process technology under the name of the Kidd Process. This has resulted in the supply and installation of permanent cathodes and associated product handling equipment to refineries in Canada, the United States, South Korea, Chile and Mexico. These installations accommodate both electrorefining and electrowinning processes. The growth and industrial acceptance of the Kidd Process has generated technical advancements in the areas of product random sampling, corrugation, marking, labeling, product tracking and data acquisition. In a different area, the expanded development of custom materials processing at Kidd created a need to advance technologically. The process-related problem of high nickel concentrations in refinery electrolyte compromised an increase in current density to >300 A/m2. The need for nickel removal resulted in Kidd Creek's newly developed Nickel Recovery System. The effective and economical extraction of nickel, along with reduced antimony and bismuth levels, reduces bleed stream volumes and/or neutralization costs and simultaneously produces a marketable nickel carbonate product.

Jan 1, 1999

By Chen-Ming Kuo, Esher Hsu

"Under the 4-in-1 recycling system, Taiwan producers and importers who using packaging containers have responsibility to pay the recycling fees for recycling the waste packaging containers they produced or imported; while the collectors/recycling plants who collect/sort/recover waste packaging containers receive subsidy for conducting recycling. A reasonable pricing for recycling charge and subsidy is a way for sustainability of the recycling. The objective of this study is to provide an amending mechanism for product charge and recycling subsidy in response to the social economic changes. This study employs a regression analysis and cost adjusting model to link the factors used for calculating product charge and recycling subsidy on recycling waste packaging containers with socio-economic indicators, raw material prices, wholesale prices, and secondary material prices. Study results provide estimated models to EPA in Taiwan for amending product charge and recycling subsidy in response to the social economic changes.IntroductionUnder ""4-in-1"" recycling system in Taiwan, waste packaging containers are officially announced to be recycled. The waste packaging containers announced to be recycled include iron cans, aluminum cans, glass bottles, plastic containers, paper containers, aluminum foiled paper packs. In order to compensate the recycling system, EPA charges associated manufacturers and importers for recycling fee and subsidies recyclers to create the economic incentive for raising recycling performance. Basically, the budget for subsidy recyclers is from the recycling charge. That means if we want to increase recycling efficiency by increasing subsidy to recyclers then the manufacturers and importers have to pay more for reaching financial balance of recycling foundation. The benefit of recyclers and fee payers are always conflicted. The recycling charge and subsidy is thus argued by fee payers and subsidy receivers all the time. A reasonable pricing for recycling charge and subsidy is the only way to keep the recycling system sustainable. Moreover, a suitable mechanism has to be changed along with the changing social economic condition. The recycling performances and effectiveness of this recycling system is also highly dependent on the pricing mechanism. This study intends to provide an amending mechanism for product charge and recycling subsidy in response to the social economic change. Related previous studies about recycling system in Taiwan with its performance include Hsu and Kuo (2002, 2005), Bor, Chien, and Hsu (2004) and Hsu (1999). Hsu and Kuo [1] estimated total production values of recycling and evaluated the performance of recycling performance based upon the estimated production values."

Jan 1, 2011

By Ryosuke O. Suzuki

A combined process of electrolysis of CaO in the molten CaCl2 and of calciothermic reduction, so-called OS process, was applied to prepare metallic vanadium directly from V2O3. The fine metallic powder containing 1860 mass ppm oxygen was obtained using 0.5mol%CaO-CaCl2 melt for 10.8 ks at 1173 K. The oxygen level did not decrease further even when twice electricity was applied. Because the metallic vanadium could be electrochemically deoxidized to the level of 10 ppm oxygen from 1.48 %, the large amount of by-product, CaO, due to reduction and the large surface area of the fine particles are the reasons of high oxygen content in the reduced powder.

Jan 1, 2006

By Carlos Maurício Fontes Vieira, Sergio Neves Monteiro, Diogo Neves Henriques

"This work evaluates the effect of incorporation of an ornamental rock waste into an industrial clayey body used for roofing tiles fabrication. Formulations with 0, 10, 20 and 30 wt.% of waste were prepared by replacing the sand in the industrial clayey body. The plasticity of the formulations was determined by the Atterberg limits. Specimens were fabricated by 18 MPa press-molding and then fired from 850 to 1100oC. The specimens were tested to determine the water absorption, linear shrinkage and three points bending flexural strength. The results indicated that the waste improves the extrusion performance of the clayey body by decreasing its plasticity. The use of the waste was beneficial to the water absorption and mechanical strength of the fired clayey ceramic at temperatures above 1000 ° C.IntroductionOrnamental rock is a natural resource available in the municipal area of Santo Antônio de Pádua and located 150 km from the city of Campos dos Goytacazes, northe of state of Rio de Janeiro, Brazil. Intense industrial activity related to ornamental stones, especially gneisses, is traditionally occurring in the region. After mining, the flagstone is submitted to sawing to obtain blocks and then, after a manual operation, the final products are small flagstones [1,2]. During the sawing operation, a sludge composed of water and fine particles of rock is generated. A monthly production of 1000 tons of ornamental rock waste is estimated to be produced at Santo Antônio de Pádua. The final disposal of this waste has brought serious environmental problems. Since most industries do not have an adequate sludge treatment, the waste is contaminating the soil and underground waters as well as obstructing rivers and lakes.Ceramic bodies industrially fabricated in the municipal area of Campos dos Goytacazes, 280 km from the city of Rio de Janeiro, are still empirically elaborated using a mixture of local clays. These clays are predominantly kaolinitic mineral, associated with high plasticity. Due to the excessive plasticity of the ceramic bodies, it is common to have dimensional defects in the final products after the drying and firing processes. Moreover, the kaolinitic structure and the presence of aluminum hydroxide confer a refractory behavior to the local clays. This impairs sintering during the firing operation. In the case of clay ceramics for civil construction, this results in greater porosity associated with elevated values of water absorption and low mechanical strength [3,4]. To avoid these problems, it is necessary to reformulate the ceramic body composition. The addition of both non-plastic materials to reduce plasticity and fluxes to condition the refractoriness is a possible alternative."

Jan 1, 2008

By Shengli Wu, Laixin Wang, Minyin Kou, Xinliang Liu, Weidong Zhuang, Yujue Wang

COREX process has obvious advantages in environment protection but still has some disadvantages, for example, it has a higher sulfur content of hot metal than blast furnace. In this paper, the thermodynamics and dynamics of desulfurization have been investigated to obtain the main operation parameters related to the mass fraction of sulfur in the hot metal. In addition, statistical analyses have been carried out to study the relationship between operating parameters and sulfur content of COREX hot metal based on actual plant data. It has been found that the mass fraction of sulfur in hot metal is significantly influenced by the C content in hot metal, MgO/Al2O3 in slag, the concentration of MgO in slag, the temperature of hot metal and binary basicity (R2).A linear model has been developed and subsequently used for reducing the mass fraction of sulfur in hot metal, improve the quality of hot metal and contribute to low carbon ironmaking.

Jan 1, 2016

By S-L. Jämsä-Jounela

Fault diagnosis systems have attracted growing interest in a number of engineering fields. The number of applications has increased and successful results have been widely reported. The fault diagnosis system presented in this paper is integrated, and it monitors the states of the process and performs fault detection and diagnosis on the process equipment. The monitoring of process states is carried out by means of Kohonen Self-Organising Maps that is a powerful tool in visualisation and analysis of high dimensional data in engineering applications. This paper presents the results of SOM analysis carried out on the Outokumpu flash smelting process. The subsystems analyzed in more detail are the condition of the concentrate burner, the condition of the gas line on the basis of the pressure distribution in the process and the cooling water circulation of the waste heat boiler, and the condition of the furnace and furnace equipment on the basis of the temperature distribution in the furnace and gas line. Keywords: Fault diagnosis, Process monitoring, Kohonen Self-Organising Maps, flash smelting

Jan 1, 2001

By Takeo Fujino, Nobuaki Sato, Junichi Hasegawa, Masato Nakazawa, Kohta Yamada

"Tantalum oxide thin films were deposited on quartz substrates by laser ablation of Ta2O5 target using Nd:YAG pulse laser. Deposition-was observed when a laser light energy higher than 200 mJ and its repetition rate higher than 3 Hz. A thin film of 0.1 µm thickness was obtained by the ablation using a laser light of 300 mJ and 6 Hz for 2 sec. The thickness of the film increased with increasing energy, repetition rate and irradiation time of laser. By the SEM observation, it was found that many island-like particles were deposited on quartz substrate forming a thin film. The obtained thin film, which was identified as ? Ta-O by X-ray diffraction, was oxidized to Ta2O5 by the heat treatment in air at I273 K for 3 h.IntroductionTransition metal oxides have a potential to show special characteristics in electrical, magnetic and/or optical properties. When such compounds are fabricated in the form of thin film, the special properties would be improved or new characters would appear in comparison with bulk materials. Tantalum penta-oxide is widely used as a capacitor since Ta2O5 shows high dielectric constants up to high temperatures. The tantalum solid capacitor has been fabricated by the electrical oxidation of sintered Ta metal cylinder followed by MnO2 film coating. However, further improvements, reduction and layered structure formation, are required for compacting the devices. The layered structure of thin films would be applicable for the above requirements. The formation ofTa2O5 film by low pressure CVD1), photo CVD2) and magnetron sputtering3l were reported. The laser ablation -method is one of the most convenient techniques for the deposition of thin films from their compounds, such as oxides. Formation of Ta2O5 film by pulse laser deposition (PLD) method using ArF excimer4), Nd:YAG (533nm)5) and TEA CO2 6 lasers was reported. In these PLD studies, ablation was carried out in relatively high oxygen pressures resulting in formation of Ta2O 5 film. In this paper, the deposition of tantalum oxide thin film by the laser ablation of Ta2O 5 using Nd:YAG pulse laser was examined at a viliety oxygen pressures ranging from 10-8 to 10 Torr. The morphology of the films was also investigated in relation with substrate temperature and oxygen pressure."

Jan 1, 2000

By Raj P. Singh

Applications of cementation in the recovery of metal ions from process solutions have been known for a long time. Cementation reactions involve electrochemical precipitation of a noble metal from solutions of its salts on a more electropositive metal which, in tum, progressively dissolves. For example, addition of zinc metal powder in a solution containing zinc and cobalt ions would allow for the precipitation (separation) of cobalt according to the following chemical reaction. This paper pertains to the recovery of cobalt from cobalt process solutions via a cementation reaction on aluminum shavings (metal scraps from cans etc). Specifically, we report on the characterization of cobalt process solutions, a by-product obtained from cobalt chemicals, and the kinetics of cobalt, nickel and manganese cementation from process solutions on aluminum shavings.

Jan 1, 2000

By Baozhong Zhao

The direct smelting of copper concentrates to copper metal in a single furnace offers environmental and energy advantages over conventional two-stage copper smelting processes. However, the direct copper making results in unacceptably high level impurities (As, Sb and Bi) in the anode copper. Experimental studies have shown that it is possible to remove these impurities from molten copper by injection of sulfur-hexafluoride. This paper discusses the experimental findings on the influence of various factors on the rate of removal of impurities, such as the impurity inter-effects, initial oxygen content in the metal and injection rate of SF6.

Jan 1, 1995

By Shun Myung Shin, Dong Hyo Yang

Cobalt is recovered from square type of spent lithium ion batteries (LIBs) containing 5~20 % Co, 5~7 % Li, 5~10 % Ni, 15% organic chemicals, and 7% plastics together with Cu, Al, Fe, and Mn. The waste LIB was prepared by physical treatment. After screening, the crushed LIBs were separated to +8 mesh, -8/+16 mesh, and -16 mesh powder. Among these, -16 mesh powder was selected for leaching. The leaching test was investigated at 2 M H2SO4, 6 vol.% H2O2, reaction temperature 60 ?, agitation speed 300 rpm, solid/liquid ratio 50 g/ 500 ml, reaction time 1 h. The leaching efficiency of cobalt was more than 99 % and its concentration was 24.9 g/L. For removing of impurities such as copper, iron, and aluminum in the leaching solution before cobalt solvent extraction, the impurities were eliminated by pH control with alkali solution. For selective extraction of cobalt, the aqueous phase removed impurities was equilibrated with different volumes of 0.4 M Cyanex 272 saponified of 50 %. Extraction efficiency of cobalt was about 80 % at first step. Separation coefficient (ßCo/Li) of cobalt and lithium extractions was 206.5. Over 9.0 % of pure cobalt sulfate solution was obtained after stripping with H2SO4 solution.

Jan 1, 2008

By Duclerc Fernandes Parra, Washington Luiz Oliani, Christiano Gianesi Bastos Andrade, Ademar Benevolo Lugão, Danilo Marin Fermino, Francisco R. Valenzuela Diaz

This work concerns the study of the effect of discarded bond paper on the mechanical behavior of polypropylene/organophilic clay nanocomposites. A brown polycationic bentonite from the state of Paraíba, Brazil, was treated with sodium carbonate to transform it into a bentonite that swells in water and then treated with hexadecyltrimethylammonium ammonium chloride to transform it into a bentonite that swells in organic liquids. Polypropylene with 3 % polypropylene graft compatibilizer (PP-g-AM) was mixed with 1 % and 2 % by weight of discarded bond paper and with 1% and 2% by weight of organophilic clay using a twin-screw extruder. The specimens were prepared by the injection process. The clay as received and after organophilization was characterized by XRD, SEM, and capacity of swelling in water and in organic solvents. The nanocomposite specimens were characterized by XRD and thermal analysis. The mechanical behavior of the injected specimens was evaluated by strength, flexural and impact tests. The nanocomposites showed improved mechanical properties compared with the polymer without filler.

Jan 1, 2015

By P. A. Botha

Most sinter producers prefer to use a range of iron ores with the aim to optimize their sinter blends. ISCOR is however limited to the use of ore from two deposits, namely Sishen and Thabazimbi. Only sinter produced from Sishen ore is described in this report. The Sishen iron ore deposit provides high-grade hematite ore with a mean iron content of 65 per cent. Three major ore types are developed: massive, laminated and conglomeratic. The main ore mineral is hematite with minor to trace amounts of quartz, mica, phosphates and, in places, carbonates. A sinter product is characterized by its mineralogical composition and metallurgical properties. The production rate also plays an important role in the economic evaluation of sinter quality. Sinter-pot tests were conducted with varying basicities, given as the ratio of CaO to SiO:< and coke content. The results of these tests were characterized by mineralogical and metallurgical methods. Basicity of a sinter mix directly influences the mineralogical composition and metallurgical properties. The content of calcium ferrite and calcium silicate increases with increasing basicity, thereby increasing the reducibility and cold strength of the sinter product. Experiments performed during this study provided a model for the optimization of the sinter mix with respect to its mineralogical and metallurgical parameters.

Jan 1, 1991

By J. H. Meza V

La Caridad operated at only 65% of design capacity during the first five years of operation. After the first major shutdown and repairs to the furnace in mid- 1992, the smelter quickly reached 95% of design capacity. Converter operation is now more efficient; blowing times have decreased from about 1.7 to 1.2 min/ton of matte. Anode copper production is now 15000 tons/month. The increased efficiency provided by better coordination and scheduling ensures La Caridad&apos;s ability to operate at present and expanded production capacity while simultaneously meeting environmental control standards.

Jan 1, 1993

By Z. Yang

The flotation behavior of the. green algae Chlorella vulgaris and a wild Chlamydomonas spp. was studied in the presence of Zn(II) using dodecylammonium chloride as collector. At about pH 6. both organisms readily float as amine concentration approaches lx10-3 kmol/m3. In addition, electrokinetic measurements were made on the organisms as a function of pH in both the presence and absence of Zn(II). It was found that the Zn(II) has a considerably greater effect on the zeta potential of C. vulgaris than on Chlamydomonas. Zn(II) adsorption studies also indicated that C. vulgaris is able to accumulate more Zn from solution than the Chlamydomonas.

Jan 1, 1991