Search Documents

By Alaina B. Hanlon

Keywords: Undercooling, Convection, Dendrites, Stainless Steel, Levitation Certain Fe-Cr-Ni stainless steel alloys solidify from an undercooled melt by a two-step process in which the metastable ferrite phase forms first followed by the stable austenite phase. Recent experiments have shown that the lifetime of the metastable phase is strongly influenced by flow within the molten sample. The current research will provide insight to why flow affects the metastable phase. This new understanding will lead to the use of convection to control microstructural evolution in spray-forming of stainless steels. Simulations using a commercial computational fluid dynamics package, FIDAP, yield a range of convective flow velocities that cause mechanical damage to the dendrites which is compared to experimental results. If the convective velocities are great enough that the dendrites bend, then low angle boundaries form at the points of collision. These result in high energy sites that could serve as nuclei for the stable phase.

Jan 1, 2005

By Yuanbo Zhang

Keywords: Complex Iron Ores, Roasting, Tin, Zinc, Pellets, Comprehensive Recovery. The complex iron ores containing tin, zinc are typical refractory ores. Large reserves of the ores are found in China and have not been utilized efficiently so far. A new process of tin and zinc recovery and pellet preparation from iron concentrate containing tin and zinc by controlled atmosphere roasting is developed in this investigation. The results of 2573 N/P compression strength of product pellets, the 91.49% and 82.22% volatilization of tin and zinc respectively, are achieved for a concentrate containing 0.39% tin and 0.28% zinc. The strength and chemical compositions of the pellets meet the requirement of blast furnace ironmaking. Volatilization mechanism of tin and zinc are investigated. Thermodynamic study shows that the reduction balance curves of SnO2(s) and SnO(g) are proximate in the presence of carbon, and the standard formation free enthalpy of FeO and SnO2 is also approachable. Therefore, it is difficult to realize the complete volatilization of tin in the form of SnO(g) by selective reduction. But SnO2(s) and SnO(g) will form SnCl4(g) or SnCl2(g) in the presence of chlorides and can be easily volatilized from the ores.

Jan 1, 2005

By Elisa Alonso

Recycling is generally a more sustainable alternative to landfilling. Its financial costs however, do not always justify its practice, especially in the short term. As a result, even for precious metals such as platinum, significant amounts can end up unrecovered. In considering risks of materials scarcity for firms that require platinum and platinum products, this paper examines how recycling provides additional benefits as a risk-mitigating strategy against scarcity. The experimental platform for this examination is a System Dynamics simulation model that strives to capture the dynamics of platinum market supply, demand and price. The detailed structures of supply and demand are key features of the model. Results show that since the secondary supply of platinum depends on a supply chain separate from primary extraction, recycling can diversify the risks of primary supply instabilities and reduce the impact of price fluctuations upon firms.

Jan 1, 2009

By K. Morsi

Carbon nanotube (CNT) reinforced metallic composites have been recently generating significant scientific interest, due to their expected superior properties compared with other composites. Out of the metallic matrices investigated for reinforcement with CNTs, aluminum has received considerable attention. A major problem has been the dispersion of CNTs in metallic matrices. This paper discusses preliminary results on the mechanical dispersion of CNTs in aluminum powder, powder processing, stability and characterization of aluminum dispersed with CNTs at reinforcement levels equal to and below 5 wt.%.

Jan 1, 2009

By B. Xu

Keywords: Magnetic damping, g-jitter, Hot-film anemometry Results from an experimental study on natural convection induced by temperature gradient in molten gallium contained inside a rectangular container. The damping effect of the convective flow from an externally applied static magnetic field is investigated. Induced velocity and temperature fields are mapped using a standard constant temperature hot-film anemometry and a thermocouple with and without the applied magnetic field, respectively. Detailed experimental setup and procedure are depicted in the present paper. Obtained velocity and temperature profiles are examined against previous numerical simulations and reasonably good agreement has been achieved. Obvious damping effect can be observed in both the temperature and the velocity profiles when the external magnetic field presents.

Jan 1, 2005

By A. C. Neiva

An energy-dispersive x-ray fluorescence spectrometer was assembled with the aim of analysing alloys and corrosion products of artistic, ethnological and archaeological pieces. The spectrometer is semiportable and consists basically of an 60kV/1.5mA X-ray tube with W anode and a Si-drift X-ray detector with Peltier cooling, with no need of liquid nitrogen. It was used for the analysis of the alloys and occasional corrosion products of several metallic pre-Hispanic pieces of the Museum of Ethnology and Archaeology of the University of São Paulo. Special care was taken to account for the contribution of spurious radiation from both the Pb primary collimator and the Zr detector collimator. The main components of most alloys were Au, Ag and Cu, but Pb, Ca, Fe and other elements were also identified. The characterization of the alloys and corrosion products is important for the subsequent conservation of the collection.

Jan 1, 2006

By Alex Del Castillo

The mineral processing industry has followed the development of database control systems, and various systems have been installed in existing and new plants. The goal is to improve product quality, raise productivity and lower production costs. Improvements in different units for mineral .processing .have been applied. This has led to increasing information for the operators. To support the operators and for an easy overview of the process, a complete concept for an integrated process-control system is required. This paper describes the plant-wide [process control system for the Collahuasi copper project located in northern Chile. The total investment for the project was $1,700,000,000 and included a port area and two copper processing plants, an oxide plant with a cathode production of 50 tons per year and a sulfide plant with a concentrate production of 330 kilotons per year. The main characteristics of the plant-wide process control system include a 200- kilometer long redundant control network and a 24-kilometer long redundant serial network providing coverage for the entire plant. The plants are located around 4,700 meters above sea level, serial communication lids allow the integration of over 2,700 SCADA data units, and the system handles over 7,500 physical signals plus the SCADA data integration. The main equipment consists of 39 different sized controllers, 16 operator stations, 5 engineering stations, 2 information management systems and 4 X- terminals. The project management, control configuration, factory acceptance test, system integration test, training, commissioning and start-up were carried out in close cooperation with the customer. The result was completely satisfactory for the customer.

Jan 1, 1999

By I. Nikolic

Twin-roll casting is an integrated casting and rolling process that involves the continuous solidification of a melt and the plastic deformation of the solidified metal between two rotating rolls. Computer modeling is a valuable tool to help engineers understand the metallurgical process during twin-roll casting. However, commercially available software can only model either the fluid flow/heat transfer of the melt or the plastic deformation of the solid, but not both. In this study, an object-oriented finite element program was developed to simulate the steady-state fluid flow, solidification and plastic deformation of an A7,31 magnesium alloy in a horizontal twin-roll caster. The melt, the mush zone and the solid were treated as a generalized Newtonian flow in an Eulerian reference frame and different constitutive equations were employed to describe the material behaviours. The effect of operational parameters on the solidification process was discussed based on the simulation results.

Jan 1, 2010

By Nan Wang

Based on the commercial computational fluid dynamics software, Fluent, the fluid flow and temperature field in an iron-bath reactor were simulated numerically, and the effects of top-blown and side-blown operating parameters on the mixing time of iron bath, distribution range of oxygen in top space, and post-combustion ratio were investigated. The simulated results showed that the mixing time of iron bath increased initially and then decreased with the increase of inclined degree and immersion depth of side-blown lance. The distribution range of oxygen became wider as pulling the top lance away from the iron bath. Furthermore, post-combustion ratio was reduced given the top lance was too close the bath. The simulation results provide theoretical base for the process optimization of iron-bath reactor and further development of new type iron-bath smelting reduction process.

Jan 1, 2009

By Nikhil Dhawan

Electronic waste (e-waste) is a collective name given to discarded electronic devices such as Television, Cellular Phones and Personal Computers. Among the heterogeneous metals present in the e-waste are the base metals: copper, aluminium, nickel, tin, zinc, iron and precious metals: gold, silver, palladium, platinum apart from several hazardous and halogens metals. Hence there is a need to recover these metals from electronic scrap by recycling and then re-use, which can meet large amount of metals demand. Hydrometallurgical processing was employed for the recovery of metals from television printed circuit board (TV PCB). Different lixiviants such as hydrochloric acid, Sulphuric acid, and nitric acid were used to understand the dissolution behavior of copper, iron and lead present in the TV PCB. Effect of increasing concentration of nitric acid was also studied. Selective recovery of tin over 95% in the form of tin oxide was precipitated. The precipitated tin oxide was identified by X-ray diffraction technique. Tin oxide of purity more than 99.9% was obtained.

Jan 1, 2009

By Harumasa Kurokawa

Since the initial start-up, the Toyo Smelter & Refinery has been operating in harmony with the ambient environment, and improvements have been implemented with technologies specifically developed for further protecting the environment. Toyo Smelter & Refinery is now planning to increase the copper production capacity from 280,000 tpy to 450,000 tpy, over a period of several years. In 2003, the first step of this smelter expansion and modernization plan was implemented. The production capacity of the P-S converter was increased dramatically, as it became possible to operate under a ?2 hot-2 blowing? schedule. In 2005, an additional converter will be installed, in order to allow operation under a ?3 hot-2 blowing? schedule. This report will describe the technical improvements on the P-S converters, as well as describe the Toyo expansion program and discuss the technologies applied to the fugitive gas collecting system.

Jan 1, 2005

By C. M. F. Vieira

This work has as its objective to characterize ceramic bodies for vitrified tiles elaborated with the mixture of nepheline-syenite flux and kaolinitic clay. Formulations were prepared with 0, 30 and 50 wt.% of nepheline-syenite incorporated in a kaolinitic clay. To determine the physical and mechanical properties such as dry bulk density, linear shrinkage, water absorption and flexural rupture strength, specimens were prepared by 30 MPa uniaxial pressure-molding and then fired in a laboratory furnace at 1150oC. The microstructure of the fired ceramics was evaluated by scanning electron microscopy. The results indicated that the nepheline-syenite improved the evaluated properties of the clay and attended the specifications of vitrified ceramic tiles.

Jan 1, 2010

By Jian Li

Developing the Generation IV nuclear reactor is an international collaborative effort. One of the most promising Gen IV nuclear reactor designs is the supercritical water (SCW) concept, in which the water coolant runs at about 625 oC at the outlet. Under this temperature and high pressure condition, the cooling water is at supercritical state, which poses significant demand for both in-core and out of core materials. High-temperature mechanical properties, corrosion resistance and radiation damage are some of the key challenges. At present, no single commercial material can meet all the requirements of the severe SCWR conditions. Corrosion experiments per-formed under SCW condition yield various kind of corrosion modes, some are very challenging to characterize using conventional techniques. A combination of various advanced characterization techniques proofed to be essential to understand the root cause of materials? degradation.

Jan 1, 2010

By T. V. Swaminathan

Monazite sand is normally processed by, the caustic soda route to produce mixed rare earths chloride, thorium hydroxide and trisodium phosphate. Bulk of the mixed rare earths chloride is used for the preparation of FC catalysts. Recently some of the catalyst producers have shown preference to cerium depleted (lanthanum enriched) rare earths chloride rather than the natural rare earths chloride obtained from monazite. Therefore, a process for producing cerium depleted rare earths chloride, cerium p thorium and uranium from Rare earths + thorium hydroxide obtained by treating monazite based on stepwise hydrochloric acid extraction, was developed in our laboratory. The process involves drying of the mixed rare earths-thorium hydroxide cake obtained by monazite-caustic soda process followed by stepwise extraction of the dried cake with hydrochloric acid under specified conditions.

Jan 1, 1989

By Yong-Moo Cheong

When the zirconium pressure tube(PT) is in contact with the calandria tube(CT) in the pressurized heavy water reactor(PHWR), the temperature gradient between the inner and outer wall of the PT results in a thermal diffusion of hydrogen(deuterium) and hydride blisters are formed on the outer surface of the PT. Since Zr-2.5Nb pressure tubes have a high risk for the formation of blisters during their operation in a PHWR, there is a strong incentive to develop a method for the non-destructive detection of the blisters grown on the tube surfaces. However, because there is little mismatch in an acoustic impedance between the hydride blisters and zirconium matrix, it is not easy to distinguish the boundary between the blister and the zirconium matrix with the conventional ultrasonic methods. This study has focused on the development of an ultrasonic method to detect the hydride blisters formed on Zr-2.5Nb pressure tubes. Hydride blisters were grown on the outer surface of a Zr-2.5Nb pressure tube using a cold finger attached to steady state thermal diffusion equipment. Ultrasonic velocity ratio method as well as conventional ultrasonic parameters with an immersion technique was developed to detect small hydride blisters on the Zr-2.5Nb pressure tubes.

Jan 1, 2006

By Qiang Zhang

Hybrid composites are fabricated by adding two reinforcements into matrix materials so that the expected excellent properties can be achieved through the combined advantages of short fibers, and different size particles (micron or submicron), which provide a high degree of design freedom. In this paper, hybrid preforms were produced with the different size reinforcement of the Al2O3 particles and short fibers. The Al-Si alloy-based hybrid composites were fabricated by preform-squeezing casting route. The structure and performance of composite materials were studied with the Transmission Electron Microscopy (TEM), and Scanning Electron Microscopy (SEM). The results show that the reinforcements, both particles and fibers, distribute homogeneously in the matrix materials, and the properties of composites are found to improve in comparison with the matrix Al-Si alloy.

Jan 1, 2009

By Torben Edens

Norddeutsche Affinerie?s (NA?s) primary smelter continually increased production in the past decade. The smelter?s concentrate capacity was expanded from 500,000 in 1993 to 1,000,000 t/a dry concentrate in 2000 and the goal of the present upgrade is 1,150,000 t/a. These goals were reached without erecting new equipment in the anode area, but instead by refitting the existing plant. The life-span extension of the casting moulds was absolutely necessary to increase the casting performance from 260,000 to 450,000 t anodes per year on a single casting wheel. Different mould manufacturing processes and alloys were tested in order to find the optimal mould. In the past the moulds were cast directly, now the anode mould is milled into NA copper cakes. Accompanying measures taken were the shortening of maintenance and repair times as well as improvements in the refining furnace equipment.

Jan 1, 2005

By Varadajan Seshadri

Keywords: torpedo car, kinetics, physical modeling A 1:6 torpedo car physical model was built to assess the optimum refining conditions for pig iron desulfurization in the torpedo car considering the industrial parameters used in the steel plant CSBM (Companhia Siderurgica Belgo-Mineira, João Monlevade, MG, Brazil). The refining practice in this plant is through injection of a CaO-CaF2-Mg powder in the pig iron melt. Similarity between the model and prototype were established through Froude and turbulent Reynolds criteria. Mixing times were evaluated by pulse tracer addition and the kinetics of metal/slag interactions were assessed from experiments investigating iodine transfer from kerosene to water. The influence of parameters such as level of metal, gas flow rate, lance penetration, lance orientation were also evaluated.

Jan 1, 2005

By Xuan Li

Aluminum slag is generated when aluminum metals are recycled through a smelting process in the presence of salt. There are small amounts of aluminum metals trapped in the aluminum slag. This research aims at evaluating the use of aluminum slag as an expansion agent for the production of lightweight concrete by taking advantage of the residual aluminum metals in the slag. The research identified key elements of producing lightweight concrete products through utilizing various mixture components including sodium hydroxide (NaOH), lime (CaO), cement, and gypsum. The volumetric expansion rate was investigated and the density and strength of the products were determined. The results show that aluminum slag can be utilized for the production of lightweight concrete products.

Jan 1, 2010

By A. L. D. Skury

In the synthesis of diamond, the precursor graphite must present a degree of crystallinity to assure optimum yield and quality for the transformed crystals. X-ray diffraction, SEM and TEM analyses were carried out to investigate the structural and morphologic transformations produced in natural graphite by high pressure-high temperature treatment. The present study had as its objective to characterize the morphological and structural changes suffered by a natural graphite that was subjected to high pressure and high temperature treatments in the region of diamond thermodynamic stability. The results indicate that the material that constitutes the gasket, for the deformable capsule, could act as catalyst in the graphite recrystallization process.

Jan 1, 2006