Search Documents

By Z. T. Bieniawski

This paper presents the results of a survey of room and pillar dimensions and design practice in U.S. coal mines aimed at improving the design procedures in room and pillar mining. A review is given of the current pillar strength formulas and suggestions are made for better utilization of research results in engineering practice.

Jan 1, 1981

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By Leo Gilbride

Western U.S. longwall operators face increasing challenges with optimizing ground control and productivity as mines reach greater depths and coal bursting hazards increase. Some western U.S. mines, many known to be bump-prone, achieved a successful balance between ground control and productivity by transitioning to side-by-side longwall panel mining combined with a yield pillar gateroad system. With this design, development footages could be minimized and pillar bumping averted by controlled yielding at moderate depths, generally in the range of 450 to 600 m. Over the past four decades, the yield pillar system has won wide acceptance among western mines facing pillar bursting hazards, particularly those in the Wasatch Plateau and Book Cliff coal fields of central Utah. However, recent attempts among the deepest Utah operators to mine side¬by-side panels with yield pillars at depths in excess of 600 m have been met with mixed success and, in some circumstances, with serious difficulty. Challenges include violent face bursting and excessive tailgate convergence outby the face, which can be crippling to ventilation. The use of interpanel barriers, i.e., barriers left between longwall panels, offers one possible solution to mining under deep cover with bump-prone geology. Interpanel barriers have already been adopted by Utah's deepest longwall mine, and others are considering their use. The geomechanical implications of mining with and without interpanel barriers, and the competing tradeoffs between ground control and ventilation are discussed.

Jan 1, 2004

By Brian E. Travis

The recent development of polymer grids for the underground coal mining industry has created new alternatives for supplemental ground control practices. The grids utilize strong, lightweight polymers - usually special grades of polypropylene. High tensile strengths and resulting load support characteristics are achieved by molecular orientation of these polymers in the manufacturing process. One of the most important applications of polymer grids as supplemental ground control is in longwall shield recovery. When shields are moved from one face to another, the determining factor in the success of the recovery is the ground control provided by roof support structures along the old face. Whereas primary support is usually provided by roof bolts and cables which run the full width of the panel, supplemental support is often provided by metallic meshes of welded wire or chain-link fence. lightweight, high-strength polymer grids replace these heavy, cumbersome metallic meshes, giving the operation increased productivity by decreasing installation time and reducing injury downtime.

Jan 1, 1990

By George S. Kalamaras

Coal strata strength is included as a vague term in most of the pillar design formulas, either as a questionable fraction of the intact coal strength or a size-dependent relationship for scaling down a laboratory value to the in situ strength. In order to introduce a coal mass strength criterion which would be compatible with current design trends, the Rock Mass Rating (RMR) system was revised to incorporate factors governing coal seam behavior under load. A number of adjustment factors have been proposed but, the most significant change, is the introduction of a parameter representing the heterogeneity of the seam. When developing a rock mass strength criterion, it is necessary to find the constants of appropriate intact rock strength criteria and to establish a correlation to scale down these constants as a function of the RMR. For four intact rock strength criteria, the constants for coal were found using the Nelder-Mead method. To correlate the constants of the strength criteria with the coal seam quality values (RMR), a procedure was developed based on finite element modeling of in situ large scale tests for which the RMR was known. A new coal strata strength criterion is proposed, in a principal stress formulation, for modeling coal pillar behavior when the stress field in a pillar is known. A linear relationship is also given, to be used when empirical pillar strength formulas are used to design pillars. The proposed criteria have been evaluated in a case study.

Jan 1, 1993

By Ben Mirabile, Alan Campoli, Rodney Poland

"The majority of U.S. underground coal mines use some form of cable bolt as supplemental support to a primary roof bolting system. Many coal operators employ the high load capacity of non-tensioned cable bolts, cable roof trusses, or solid bar trusses in an attempt to suspend the primary bolted horizon to overlying strata. However, in cases where many discontinuities exist in the roof strata or where pre-existing fractures are present, these passive supplemental support systems often cannot adequately control roof deflection. This paper examines the application of tensioned cable systems to minimize roof deflection in very laminated and fractured strata. Three underground case studies are presented to demonstrate the application of tensioned cable bolts. The first case study involves the rehabilitation of a longwall head gate in the Eagle Seam with highly laminated and fractured sandstone. The second case study examines the recovery of a longwall face in the Alma Seam. The final case study addresses rehabilitation of a longwall head gate in the Pittsburgh No. 8 Seam that was developed in a sandstone channel margin area and subjected to horizontal stress concentration.INTRODUCTIONDuring the previous decade, Jennmar Corporation has recognized coal operators' increasing interest in tensioned cable bolts. The majority of these tensioned cable bolt systems have been applied in adverse roof conditions including broken ground, high horizontal stress areas, and highly laminated roof strata. In most cases, qualitative data on roof conditions after application of tensioned cable bolt support indicate successful implementation of these systems. The qualitative evidence suggests that the combination of high load' capacity and applied tension provides superior supplemental roof support in adverse roof conditions. This research aims to quantify the effects of applied tension to cable bolts. This paper will review the types and installation of tensioned cable bolt systems, present initial laboratory test data, discuss successful case studies, and propose an instrumentation system for quantification of tensioned cable bolt performance."

Jan 1, 2010

By Stephen C. Tadolini

The U.S. Bureau of Mines (USBM) is conducting research to provide alternatives for traditional secondary support methods. These cost-saving methods are proving to afford safer installation, improve entry stability, eradicate material-handling injuries associated with crib supports, and enhance ventilation. In cooperation with Mountain Coal Company, the USBM replaced timber cribbing with high- strength cable supports to provide stability in a gate road that was used for two longwall panels. The support design consisted of 2.1-m (7-ft) full-column resin-grouted bolts and 4.8-m- (16-ft-) long high-strength resin-grouted cable supports. Three support concepts were evaluated: passive, stiff, and tensioned systems. Cable loading and roof deformations were monitored to evaluate the behavior of the immediate and main roofs during panel extraction. The stress and loading histories for both panels and the abutment and yield pillars were monitored to assist in evaluating the stress transfer and pillar performance in conjunction with the roof behavior. The test results indicated that resin- grouted cable support systems successfully maintained the immediate and main roofs during the extraction of two longwall panels. This paper describes the theory, application, and advantages of resin-grouted cable supports and presents the mine measurements made to assess the cable performance during the retreat process of longwall mining.

Jan 1, 1994

By H. N. Maleki

Tension-torque relationships were investigated *n a coal mine for bath standard 5/8 in. (16 mm) bolts and a vibrating wire instrumented bolt, using conventional and controlled installation techniques. The instrumented bolts differed from the standard bolts by their head size and hole preparation procedures. The controlled installation technique developed by the U. S. Bureau of Nines (USBN) involved using hardened washers and lubrication in the bolt assembly, and maintaining a minimum thrust level during bolt installations. The object of this study was to determine the tension to torque ratio (lb/ft-lbs; for standard bolts and instrumented bolts for both conventional and controlled installation techniques, and to modify the bolt assembly so that the ratios would be equal for the instrumented and standard bolts for both installation techniques. It was shown that the instrumented bolts installed in faced holes had a similar tension torque ratio td that of standard 5/8 in. (16 mm) bolts installed in unfaced holes for each installation technique, and thus they were representative of other uninstrumentea bolts. This was achieved by evaluating the influence of several factors oh the relationship, including: facing the hale surface, introducing washers and lubrication in the bolt assembly, and applying different levels of thrust at installation due to bolter operator practice. The tension to torque ratio fur conventional bolts was only 21 (lb/ft-lb) for the coal mine, resulting in an installation tension of 4000 lbs (17.8 kg) with the typical installation torque of 150 to 400 ft-lb. This tension level was approximately 50 percent of the required bolt tension, and thus, it was concluded that torque standards are not sufficient to assure adequate bolt tension. .he low tension levels were due to the particular wait hardware in use, operator practice, and bolt fencing.

Jan 1, 1984

By Kikro Matsui

Longwall mining 1s more productive in comparison to other methods but requires particular conditions for its effective use This paper relates to longwall roof instability at Ikeshima Colliery In order to make clear the cause of the longwall roof instability, scientific investigation in terms of geomechanical factors and longwall support system was planned and carried out

Jan 1, 1997

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Daniel S. Mazzei

This paper will be a general discussion of surface flooding considerations as they affect mining facilities site selection, based primarily on experience with several such problems with which MSHA's Bruceton Technical Support staff has been involved. The detailed analytical procedures used in arriving at engineering solutions of these problems will not he presented here; the emphasis is on drawing attention to this additional aspect of mine design which hitherto has been largely overlooked due to insufficient awareness, information and criteria. The paper's purpose is to stimulate thought and offer guidance concerning the selection of sites for mining facilities in light of the potential for flooding problems caused by surface waters. Flooding by surface waters, would generally not be a serious consideration in areas of relatively low topographical relief, i.e. flat lands, although there are exceptions to this rule, for example, in Western areas where flash flooding is a major concern. Therefore, this discussion will mainly apply to areas where the severity of surface flooding would be amplified by the topography-large, well defined watersheds of considerable relief, i.e. mountainous areas. In these regions, steep valley walls cause any rainfall to flow quickly into the relatively narrow valley bottoms. These valley bottoms provide little flow area during storm conditions, so deep and rapidly flowing streams result.

Jan 1, 1982

By Erik Westman, Benjamin Mirabile

"Quantitative evaluation of secondary support performance in longwall tailgates in U.S. coal mines was introduced with the U.S. Bureau of Mines (USBM) Wood Crib Performance Model. This model evaluated crib performance based on load capacity, stability, and convergence characteristics. The introduction of a large variety of alternative secondary supports in the 1990s prompted a full-scale load-displacement testing program conducted by the USBM and, subsequently, NIOSH. The application of the ground response curve concept to secondary supports provided a more complete estimation of secondary support loading in longwall abutment zones. Secondary support loading from floor heave, horizontal stress effects, and pillar yield are captured by the ground response curve. A point on the ground response curve can be measured by instrumenting a secondary support with load and convergence measurement devices. A segment of the ground response curve can be measured by instrumenting two secondary support types of varying stiffness. Numerical models have been used to construct complete ground response curves for longwall tailgates based on measured secondary support performance. The ground response curve concept can be used as a design methodology for secondary supports in the #2 entry, as well as the longwall tailgate. Extending published evaluation and design methodologies for secondary support in longwall tailgates, a ground response curve unique to the loading conditions and required functionality of the #2 entry can be developed. Numerical models can be used to construct full ground response curves based on measured data in the #2 entry.INTRODUCTIONA longwall ventilation system is designed to continuously dilute and move methane-air mixtures and other contaminants from the active face, to bleeder systems, and out of the mine. The #2 entry of the tailgate gateroad serves to transport contaminated air from the longwall face to the bleeder system. The #2 entry is required to function as an air course between two longwall gobs and is subject to significant ground movement and loading. Current ground support design and evaluation practices are based on empirical evidence and little to no quantitative data on support performance exists for these entries. Substantial volumes of research have been conducted on ground movement and support performance in longwall tailgate entries. Following the successful ground support evaluation and design practices established for longwall tailgate entries, a practical and efficient design methodology can be adapted for supporting the #2 entry of a three-entry gateroad system."

Jan 1, 2018

By Sun Henghu

This paper analyses problems associated with cement based technique in metal mines, and provides a new mining technique of packing the tailing sand and water into solidified material. In the new technique, the cementing agent is a solidifying material containing a high percentage of water and tailing sand. The sand and water solidify into the packed body at the same time. The slurry of the packed body varies widely in concentration and suitability for different mining conditions. It consists of two liquid materials, each composed of a cementing agent, tailing sand and water. The thick liquids are transported to the packing place at the same time. Their pumping property is good; they do not solidify or block up the pipe during transportation. At the packing place, the two liquids are evenly mixed. The mixed liquid flattens out well and its solidifying speed is so fast that it solidifies into a packed body within a very short period of time. The compressed strength of the packed body can reach 1.2-5MPa in one day, which satisfies the requirements of different mining conditions. By using the new mining technique, all the tailing sand can be used again in the packed body and it is low in cost and investment. The mechanisation is easy and thus the working efficiency is increased and the use of labour decreased. Contamination problems caused by excess water drainage under the ground are resolved.

Jan 1, 1992

By J. K. Owens

As part of a larger research effort focused on ground control, the U.S. Bureau of Mines is currently evaluating the effectiveness of using stereological analysis for characterizing mine roof strata. Input for a stereological analysis of a rock mass is best obtained by scanning (imaging) the walls of clean drill holes using a video-imaging borescope or other video device. Two classes of features are being investigated: (1) Lithologic types that comprise the overall rock mass and (2) structural discontinuities (e.g., joints, foliation, bedding planes) within a given lithologic unit. In the former, the volume fraction of a given Lithologic unit in relation to the entire rock mass can be estimated. In the latter, the mean intercept length between adjacent structures and surface area density of the geologic structures can be estimated. Examples of sampling procedures and subsequent computations are presented for several situations using information collected from drill holes in roofs of underground mines. One such example is based on the trace of a cycloid curve used as a stereological sampling path on the cylindrical wall of a drill hole. Stereological measures, such as intercept length, volume fraction, and surface area density, are explained in the context of rock mass characterization.

Jan 1, 1994

Virtually all mineable Appalachian coal seams exist in a multi-seam environment. This makes it inevitable that most seams will eventually experience interaction induced ground control and mining problems. Indeed, it has been estimated that every working face will experience interaction effects from previous or current workings at least once during its lifetime (1), and that these problems are considerably exaggerated when seams are in close proximity -- a distance of less than 110 feet. The continued increase in multi-seam problems has resulted in considerable research activities over many years (2,3,4,1). Theoretical analysis, numerical and physical model studies, statistical and empirical analysis of numerous interaction related field data have been applied to multi-seam mining situations and have identified many useful trends and design criteria (4,5,6,7). To fully utilize research results and transfer multi-seam mining technology to field engineers, a design model -- USEAM was constructed (8). This model, designed for close seam under-mining situations, was computerized to facilitate utilization. In the current research, a new computer program "MSEAM" was developed to produce a model for both under- and overmining close seam situations. It is hoped that both of these software packages will aid field engineers in using important interactive design criteria to gain a better understanding of interaction mechanisms. Through advance planning with these programs, detrimental interaction may be avoided and minimized, and occasionally a design can be selected which will allow interaction effects to be utilized to the benefit of mining operations.

Jan 1, 1987

By Erdal Unal

In gate roads where supports are subjected to dynamic loading four times due to retreating longwall panels, it is a real challenge to replace the rigid arches with flexible reinforcement systems and yet to provide safety and stability of these openings within better economical limits. The results presented in this paper are based on a three years of research project aimed at developing safe and economical support systems for gate roads in Çayìrhan coal mine. Çayìrhan -Mine Project includes laboratory and field studies, design analysis, pilot scale design applications and performance monitoring. Based on outputs of the design approach developed, four types of bolts, namely, Split Set, Yielding Super Swellex, Sis-Resin, and Fosroc-Resin bolts were installed in a gate road together with widely spaced yielding steel-arches. In order to compare the performance of these flexible support systems and to provide feed back for the design approach, a monitoring program was initiated.

Jan 1, 1993

By Tim Ross

Slurry injection into mined-out panels is an attractive alternative for disposal of coal preparation plant fines. however, in areas where surface subsidence cannot be tolerated, either by law or necessity to protect surface structures or aquifers, special consideration trust he given to the effect of slurry injection on panel stability. Slurry injection can lead to panel failure and unplanned subsidence by degrading roof, pillar, and floor strength. Water degradation is of particular concern where clay is present in the floor. Recently. unplanned subsidence related to slurry injection occurred at an Indiana room-and-pillar coal mine subject to weak floor conditions. This paper discusses the efforts of the mine operator to determine the causes of the panel failure and to design panels and injection procedures to allow for future economic slurry injection without subsidence. The numerical and empirical/analytical techniques applied give the operator a rational approach to pillar panel design for future injection panels under various cover depths and weak floor conditions.

Jan 1, 1998

By G. Bucelluni

An essential element of truss bolt installation requires machines to angle a hole in the top of approximately 39° to 45° from its vertical axis. Parameter which inherently effect the drill position are: height, width of truss, physical size of mast, and whether single or dual mast bolting is utilized. The combination of these facets govern the installation procedures required for the bolting cycle. The following illustration with written explanation will demonstrate this concept. See Figure #1. [ ] This model assumes certain fixed criteria which corresponds to a dual mast drill design and a set 41° drill angle. Using the derived formula, the maximum possible seam height for both masts to touch the bottom can be calculated for any given condition by substituting by the appropriate bolt spread distance. [ ] In a high seam application where the mast touching the bottom was considered a requirement, the proposed model demonstrates the advantage of single mast drilling. See Figure #2. [ ]

Jan 1, 1982

By Wm. Mark Hart

Under a specific geological condition, roof supporting method, and pillar-entry system, an entry convergence concept may be the most effective means that can be used to effectively indicate the longwall entry stability (i.e. pillar bumps, roof falls, or floor beaver This concept may also be used to verify the effectiveness of the current pillar-entry system and roof supporting method. Furthermore, convergence measured under different mining phases may lead to a better understanding of the longwall mining-induced abutment loads and may be used to estimate stress change in pillars and thus pillar stability. In this paper, a remote entry activity monitoring system was designed; a comprehensive entry convergence monitoring strategy was proposed; thee abutment loading phases in longwall mining were defined; the relationship between roof deflection and stress change in a pillar was derived, and finally the extent and magnitude of the mining-induced abutment loads as well as their impact on entry convergence were discussed using the field data obtained so far.

Jan 1, 1995

A procedure fm the estimation of pilla1 strength is presented where the design of underground coal pillars is emphasized. An analytical approach has been developed, proposing that the effect of end constraints on the pillar strength and the ductile behavior of coal material should be incorporated in the computation of the stability of coal pillars. Bad on this approach, it has been found that end constraint has a significant influence on the pillar strength. The study indicates that when the end constraint is zero the computed strength of the pillar is the same as the unconfiied compressive strength of the coal mass and will not increase with the increase in the width to height ratio. However. when the end constraint is greater than zero the pillar strength will increase exponentially as the width to height ratio increases.

Jan 1, 1990